Tender For special Repair To Bldg No P-6/29A (Sm Bk Ofd) & P-6/39 (Office & Store) Of Fd Regt And Provn Of Toilet Block At Tech Area Of Rpas Flt At Mil Stn Jammu Under Ge Satwari
Tender Value
34.13 Lakhs
Estimated cost
Bid Submission
29 Aug 2026
0 days left
EMD
68260
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jammu → Jammu and Kashmir
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repair To Bldg No P-6/29A (Sm Bk Ofd) & P-6/39 (Office & Store) Of Fd Regt And Provn Of Toilet Block At Tech Area Of Rpas Flt At Mil Stn Jammu Under Ge Satwari
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of brick work or stone/boulder masonry , built in cement mortar or cement lime mortar including all quoins, arches & pillars etc of any description and in any position and removing unserviceable material from work site to outside defence premises complete all as specified and directed |
| 2 | Demolition of reinforced cement concrete of any description & from ground floor to 4th floor and removing the rubbish from the work site to outside defence premises complete all as specified and directed. |
| 3 | Taking down cement plaster of any description on brick or stone walls or from concrete surface including raking out joints, hacking for key, scrubbing down with water etc, and removing unserviceable material outside cantt area, complete all as specified and directed. |
| 4 | M&L for brick work with sub class 'B' bricks, using old size bricks, straight or curved on plan exceeding 6m mean radius , built in cement mortar 1:6 complete all as specified and directed |
| 5 | All as per Ser item No 4 here-in-before but except brick complete all as specified and directed. |
| 6 | M&L for rendering 15mm thick in cement mortar 1:6 on brick work or concrete surface,surface finished even and smooth without using extra cement complete all as specified and directed. |
| 7 | M&L for rendering 15mm thick in cement mortar 1:4 on brick work or concrete surface,surface finished even and smooth without using extra cement complete all as specified and directed. |
| 8 | M&L for rendering 5 mm thick in cement mortar 1:3 on ceiling, surface finished even and smooth without using extra cement complete all as specified and directed. |
| 9 | M&L for preparation of new plastered surfaces of walls & applying two coats of oil bound distemper over two coast of wall care putty of 1-2 mm thick each and one coat of primer complete all as specified and directed. |
| 10 | M&L for complete removal of existing treatement on wall surfaces mechanically including washing and rubbing down , preparation of surfaces and applying two coats of oil bound distemper over two coats of wall care putty of 1 to 2 mm thick each and one coat of primer complete all as specified and directed. |
| 11 | M&L for preparation of old decorated surfaces of ceiling and applying two coats of white wash complete all as specified and directed. |
| 12 | M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed. |
| 13 | M&L for Preparation of newly plastered surfaces on wall/ roof projections including facia, cornices etc and applying exterior water proof wall care putty @ 1 Kg(un-diluted) per sq mtr. of average thickness 1mm to 2mm over the plastered wall/ceiling surfaces, one or more coats and grinding the puttied surface with mechanical grinder for make the surface even and smooth for receiving primer and applying two or more coats of 100% premium acrylic smooth exterior emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives & Color stay technology, Excellent dirt pickup resistance @ 1.79 litre/ 10 sqm diluted with water as per manufacturers instructions over and including priming coat of exterior primer applied @ 0.9 litre (Undiluted) / 10 sqm over new putty surfaces of wall/ceiling complete all as specified and directed. Note:-Painting to be done using Airless spray technology with max working pressure of 3300 PSI and capable of operating single spray gun with a max material hose length of 30 mtr the spray machine should be of reputed manufacturer. |
| 14 | M&L for complete removal of existing treatment on wall/ roof projections including facia, cornices etc by scrapping with mechanical sander (having mechanical vaccum mechanism) with sanding pad of appropriate grit to make surface clean,free from dust, loose paint etc by skilled labour with mechanical sander having RPM of 1500 - 2700 rpm, with internal dust extraction system for clean environment and preparation of old plastered/scrapped surfaces of wall/ceiling by filling cracks by external wall care putty/crack fill paste and applying exterior water proof wall care putty @ 1 Kg(undiluted) per sqm. of average thickness 1mm to 2mm over the prepared plastered wall/ceiling surfaces, one or more coats and grinding the puttied surfaces with mechanical grinder for make the surface even and smooth for receiving primer and applying Two or more coats of 100% Premium acrylic smooth exterior emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives & Color stay technology, Excellent dirt pickup resistance @ 1.79 litre/ 10 sqm diluted with water as per manufacturers instructions over and including priming coat of exterior primer applied @ 0.9 litre (Undiluted) / 10 sqm over old/new putty surfaces of wall/ceiling complete all as specified and directed. Note:-Painting to be done with airless spray technology with max working pressure of 3300 PSI and capable of operating single spray gun with a max material hose length of 30 metre |
| 15 | Taking down chowkats or frames with shutter (without taking off shutter from the frame) n. exc 1.5 sqm each including cutting holes for taking out hold fast or dismantling brick work and removing from site complete all as specified and directed. |
| 16 | Taking down chowkats or frames with shutter (without taking off shutter from the frame) exc 1.5 sqm & n. exc 4 sqm each including cutting holes for taking out hold fast or dismantling brick work and removing from site complete all as specified and directed. |
| 17 | S&F steel window 1.25 mm thick Box type (Double Shutter) ERW hollow P section of size 60 mm x 25 mm single rebated comprises glazed & wire gauged skelton shutter ERW sec 50 mm x 20 mm and 1 mm thick with two Nos sash bar of T- section 20 mm x 3 mm complete welded to frame with one vertical mullion of ERW box type T- section of size 60 mm x 25 mm and 1.25 mm thick including cutting holes and making good dismantled portion in PCC 1:2:4 type B-1 four No for each window including following fitting welded to frame shutter hold fast of 150 mm long of 12 mm x 3 mm FI made to shape 4 No, handle of Z section 20 mm x 25 mm x 100 mm long 1 No per leaf, MS tower bolt 150 mm long 2 No per leaf, Z sec 20 mm x 25 mm, 100 mm long stopper 1 No on per leaf, MS pintal hinges of size 75 mm x 12 mm 2 No per leaf fabrication, 10 mm Square bar gril, specing of gril 100 mm center to center and fixing arrangement as per drg No CEPZ/TD-324,325 complete all as specified and directed. |
| 18 | S&F pressed steel frames of size 125mm x 60 mm made out of size 1.25 mm thick MS sheet for doors with one or more rebates including mild steel hinges, 100 mm long , medium weright and 25 mm x 3 mm flat iron as in hold fast , tie bar including necessary fixing lugs, lock strike plate and fixing arrangement and making good the disturbed surfaces in cement mortar 1:3 or cement concete 1:2:4 type B-1 including PCC 1:3:6 type C1 as in back fill to chowkats complete all as specified and directed. |
| 19 | M&L for 30mm thick flush shutters, solid core construction with block board core and plywood face panels commercial type on both sides complete all as specified and directed. |
| 20 | S&F 35 mm thick 2nd class hard wood , glazed and skelton shutters, open rebated and prepared to receive glass, gauze etc divided into squares with plain, chamfered or rounded, mitred and rebated sash bars, any numbers size of members of shutters as specified in SSR Part-I Section-8 clause 8.24 (a) fitted to chowkats complete all as specified and directed. |
| 21 | S&F galvanised mild steel wire cloth , 0.56 mm normal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or stainless steel wire staples complete all as specified and directed. |
| 22 | M&L for 3 mm thick, plain sheet glass, ordinary quality and glazing with glazing pins, oil putty or with any type of beads in squares n. exc 0.5 sqm each pane complete all as specified and directed. |
| 23 | M&L for preparation of new or previously untreated wood or wooden based surfaces of any description not other wise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 24 | S&F aluminium anodised barrel tower bolts, 150mm long of extruded section, fixed to doors with screws complete all as specified and directed. |
| 25 | S&F aluminium anodised , fabricated type handle 100mm size complete all as spcified and directed. |
| 26 | S&F aluminum alloy, anodised, sliding door bolt of length 250mm with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolt and sliding bolts of extuded sections or cast aluminum alloy and fixed complete all as specified and directed. |
| 27 | S&F aluminum hanging floor door stopper ,twin rubber of size 100mm, anodised (anodic coating not less than grade AC 10 as per IS 1868) transparent or dyed to required colour and shade with necessary screws complete all as specified and directed |
| 28 | Dismantling of stone slabs and tiles of any description or thickness in floors, laid dry or pointed in any mortar complete all as specified and directed. |
| 29 | S&F machine cut kota stone slab in flooring, treads of steps, 18-20 mm thick, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing cutting and mirror polishing over and including 15 mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and directed. |
| 30 | M&L for machine cut kota stone slab 18-20 mm thick in riser of steps, skirting , dado and pillar, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, cutting and mirror polishing over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed. |
| 31 | M&L for granite (Z-Black) work 16 to 18 mm thick, any colour (table rubbed and polished) in steps, jambs , pillars, window cills , cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match shade of granite over and including 20mm thick screed bed in cement motar 1:4 complete all as specified and directed. |
| 32 | Complete removal of existing water proofing treatment of any description including under layer, taking down cement plaster any thickness and removal of debris off the premises including grubbing up of trees and preparation of concrete surfaces by scrubbing down with steel brushes and cleaning with water to remove all loose dirt/dust complete all as specified and directed. |
| 33 | M&L for PCC 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregates) as in padding over roof, finished & laid to required slope complete all as specified and directed . |
| 34 | M&L for preparation of surface free from dirt , dust & washing with water and water proofing treatment to roof surface (in four coat) with fibre reinforced elastometic liquid water proofing membrane formulated with PU hybrid polymers and reinforcing acrylic fibres with sun reflective index (SRI) of 100-110 having minimum elongation of 350%, tensile strength 2.9 MPa and shall have rack bridging ability upto 2.55 mm and shall resist 10 bars of hydrostatic pressure reduce temperature upto 10 degree celcius to RCC roof slabs, roof treatment shall be carried out in four coats to newly plaster roof surface as per the procedure given below :-(a) Apply first coat of fibre reinforced elastometic liquid water proofing membrane as described above with 33% dilution as priming coat as directed and allow it to dry before next coating. (b) Laying second coat of fibre mesh 0.3 mm thickness weave in leno pattern having weight 45 gms per sqm and pasting it properly with overlap of 50 mm as directed and allow it to dry before next coating.(c) Apply third coat of fibre reinforced elastometric liquid water proofing membrane as described in para (a) above but undiluted @ 0.45 litre per sqm of roof surface as directed.(d) Apply fourth and final coat of fibre reinforced elastometric liquid water proofing membrane as described in para (a) above but undiluted @ 0.45 litre per sqm of roof surface as directed.(e) Work shall be carried out by the authorised applicator of manufacturer and contractor shall submit a triparty agreement MoU (between contractor ,said manufacturer and their authorities appicator ) on Non judicial stamp paper to GE and shall be approved by the GE before commecement of work at site. |
| 35 | S&F 25mm outer dia stainless steel decorative drapery rod of thickness 20 gauge with stainless steel brackets near to ends with stainless steel finials at both ends and necessary fittings complete all as specified and directed. |
| 36 | Demolition of cement concrete (un-reinforced) in ground floor and pavings n exc 15 cm thickness (below or above ground level) and removing the rubbish from the work site to out side defence premises complete all as specified and directed |
| 37 | M&L for 75mm thick Plain cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregates) as in sub base, finishing surfaces even and fair complete all as specified and directed. |
| 38 | M&L for providing and laying 60 mm thick factory made charmfered edge cement concrete paver block of M-35 grade of approved colour, design & pattern as in foothpath, parks, lawns, drive ways or light traffic parking etc of required strength , thickness & size/ shape made by table vibratory method using PU mould, laid in required colour & pattern over and including 50 mm thick compacted bed of fine sand, compacting and proper embedding/ laying of interlocking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed. |
| 39 | M&L for factory glossy polished machine pressed chequered cement concrete tiles 30cmx30cmx25mm thick, polished with grey cement and pigment, set , jointed and pointed in neat cement slurry as in floors, laid over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed. |
| 40 | M&L for plain cement concrete 1:2:4 ,type B1(using 20mm graded crushed stone aggregates) as in lintels upto 1.5m clear span, window or door cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railing upto 60cm in height, copings,side posts of precast jallies etc. including slightly rounded or chamfered angles including necessary formwork complete all as specified and directed. |
| 41 | M&L for 40 mm thick plain cement concrete 1:2:4 ,type B-1 (using 20 mm graded crushed stone aggregates) as in floor finishes/ plinth protection and similar works, finished even and smooth without using extra cement complete all as specified and directed. |
| 42 | Surface excavation n.exc. 30 cm deep and averaging 15 deep and getting out in any type of soil complete all as specified and directed. |
| 43 | Excavating in trenches, n. exc 1.5 m wide and n. exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and n. exc 1.5 m in depth and getting out in any type of soil complete all as specified and directed . |
| 44 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in any type of soil complete all as specified and directed. |
| 45 | Removing excavated material to a distance n.exc 50 m & depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and directed . |
| 46 | M&L for plain cement concrete 1:4:8, type D2 (using 40mm graded crushed stone aggregates) as in foundation, filling & mass concrete complete all as specified and directed. |
| 47 | M&L for reinforced cement concrete 1:2:4 type B-1 (using 20 mm graded crushed stone aggregates) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed . |
| 48 | M&L for reinforced cement concrete 1:2:4 type B-1 (using 20 mm graded crushed stone aggregates) as in columns, pillars, piers, posts and struts complete all as specified and directed. |
| 49 | M&L for reinforced cement concrete 1:2:4 type B-1, (using 20mm graded crushed stone aggregates) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies complete all as specified and directed. |
| 50 | M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 51 | M&L for Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups , spacers and binders including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed. |
| 52 | M&L for use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter etc complete all as specified and directed. |
| 53 | M&L for use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed. |
| 54 | M&L for use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed |
| 55 | M&L for use and waste of form work to edge of concrete flats, treads, break in floors, window cills, concrete railings, openings in concrete walls , floor and roof and not exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or slopping and similar work exc 10cm but n. exc 20 cm wide for fair finished surfaces of concrete complete all as specified & directed. |
| 56 | M&L for brick work with fly ash bricks using old size bricks, straight or curved on plan exceeding exc 6 metre mean radius, built in cement mortar 1:6 complete all as specified and directed . |
| 57 | M&L for hard core of gauge not exceeding 63mm using broken bricks, deposited, spread and leveled in layers not exc 15cm thick, watered and rolled/rammed to a true surfaces complete all as specified and directed . |
| 58 | M&L for 25 mm thick plain cement concrete 1:2:4, type B-0, (using 12.5 mm graded crushed stone aggregates) as in sub base/ levelling course of floors, finished rough complete all as specified and directed. |
| 59 | M&L for 7 to 8mm thick non skid coloured ceramic tiles (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc, set and jointed in neat cement slurry and poined in white or coloured cement to match the colour of tiles over and including 15mm thick screed bed in cement motar 1:6 complete all as specified and directed. |
| 60 | M&L for glazed ceramic coloured tiles,300x450x7 mm/300x600x6mm thick, as in vertical surfaces, set and jointed in neat cement slurry and pointed in white or colored cement to match the colour of tile over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed. |
| 61 | M&L for 75mm thick PCC 1:3:6 , type C-1 (using 20 mm graded crushed stone aggregate) as in plinth protection, laid in slope in 1:30 in alternative bays not exceeding 3 mtr in length. surfaces finished even and fair including raking out joints between panel to panel and panel to wall and plugging the same with bitumen mastic using bitumen and sand mixture in 1:3 complete all as specified and directed . |
| 62 | M&L for HomeSheild PU Roofkoat(or equivalent) is a one component liquid ,solvent free , cold applied , water-proofing membrane that is highly elastic and UV resistant with 10 years warranty .ASTM D 6083-97 a Waterproofing and heat reflecting system having following key performance properties:-a) UV resistant ,prevent yellowing and weatheringb) Highly elastic upto 350% and crack bridgingc) Excellent adhesion on porous and non-porous substratesd) Tensile Strength >10 N/mm2 with GeoTextile fleecee) Soler Reflective Index (SRI) more then 109-111 ASTM E1980-11System: First coat:Providing and applying primer over the prepared surface with HS PU roofkoat Primer(or equivalent)Coverage: 0.2kg/sqm(with 50% dilution of water)Reinforcement: Geotextile 40 gsmSecond coat:Home sheildroofkoat(or equivalent)Consumption: 0.5 kg/sqm.Third coat: HS PU roofkoat(or equivalent)Consumption : 0.8 kg/sqm.System buildup-1.5kg/sqm with geotextile of 40gsm |
| 63 | S&F 12.5 mm thick sheet toughened glass (tinted/frosted/plain) as in partition wall with any type of eaching designed on glass,off cuts with necessary fixing arrangements complete all as specified and directed. |
| 64 | S&F solid PVC door frame of size 50mm x47mm made out of 5mm thick both side prelam PVC sheet reinforced with mild steel square tube, supplying and fixing in opening as per specifications and drawing including making good to distributed surface of walls complete all as specified and directed. |
| 65 | S&F Factory made solid panel PVC door shutter 30 mm thick ( style ) consisting of frame work made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour P.V.C‘ C’ channel having a PVC sheet strip 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheet for top rail lock rail and bottom rail on either side and as gap inserts for top rail; and bottom rail paneling of plain, colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles and rail with suitable PVC sheets beading and jointed together with solvent cement S&F in frame at site as per specification complete all as specified and directed. |
| 66 | S&F aluminium alloy powder coated aluminium door frame fixed with side hung shutters and glazing or composite panel LDPE core PET coating ( both side decorative type ) fixed with and including 5.0mm thick aluminium composite panel fixed with rubber gasket with aluminium heading, clips, frame made with aluminium box section as appended below complete all as specified and directed :-(a) Frame 100x38x1.48mm thick with rawl plug(b) Middle and lock rail : 85x44x1.48mm thick(c) Bottom rail : 114x44x1.48mm thick(d) Top rail/style : 114x44x1.48mm thick(e) Aluminium beading : 0.7mm thick(f) Aluminium handle D type 150mm long, aluminium tower bolt 9.9mm dia shoot 200mm long, brass mortise lock 100mm 4 leaver with stainless steel hinges (g) Making good the wall surface to match with existing finishes complete. |
| 67 | S&F pressed steel ventilators, fixed type, with glazing bars complete all as specified and directed. |
| 68 | S&F stainless steel wire cloth , 0.56 mm normal dia of wire and average width of aperture 1.18mm and fixed with stainless steel wire staples complete all as specified and directed. |
| 69 | S&F aluminium anodised , cast type handle 150mm size complete all as spcified and directed. |
| 70 | S&F 100mm long stainless steel butt hinges, fixed with screws complete all as specified and directed . |
| 71 | S&F Rotational moulded polyethlene water storage tanks of 1000 litres capacity (cylindrical vertical with closed top) with plastic lid cover, hoisted and fixed in position including PTMT Ball valves high pressure with epoxy coated aluminum rod & high density plastic ball complete, screwed for iron pipe or brass ferrule and fixed for 20 mm bore pipe including making connections complete all as specified and directed. |
| 72 | S&F Ball brass valves,high pressure,with polythene float and flynut complete, screwed for iron pipe or brass ferrule of bore 20mm complete all as specified and directed. |
| 73 | S&F Gun-metal, globe or gate valves, with iron wheel head,screwed both ends for iron pipe of 20 mm bore pipe, including making connections complete all as specified and directed. |
| 74 | S&F Galvanised steel tubing, 15mm bore, medium grade with all fittings, fixed to wall with clamps /ceiling or laid in floors complete all as specified and directed |
| 75 | S&F Galvanised steel tubing, 20mm bore, medium grade with all fittings, fixed to wall with clamps /ceiling or laid in floors complete all as specified and directed |
| 76 | S&F vitreous china counter wash basin, size 560x470x190mm, oval shape , white, to be fixed on counter/ RCC slab including chromium plated waste coupling, 32mm waste pipe,swan neck pillar tap including bottle trap complete all as specified & directed |
| 77 | S&F bib tap with flange, quarter turn, chromium plated, fancy type, cast copper alloy ,screwed down, screwed for 15 mm bore of iron pipe or for brass ferrule and fixed complete all as specified and directed. |
| 78 | S&F two way bib cock with flange,cast copper alloy , fancy type, chromium plated, screwed down for high pressure with crutch or butterfly handle, screwed both ends for iron pipe of 15mm bore complete all as specified and directed. |
| 79 | S&F PVC connection 15 mm x 450 mm including PTMT check nut at both ends complete all as specified and direced. |
| 80 | S&F Chromium plated soap dish of size 160x160x90mm, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed. |
| 81 | S&F Chromium plated tubular towel ring of 150mm dia, fixed to plugs with chromium plated brass screw including wooden/plastic beads complete all as specified and directed. |
| 82 | S&F sheet glass shelf assembly consisiting of 5.5 mm thick sheet glass, shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed. |
| 83 | S&F angle valve ,cast copper alloy , fancy type, chromium plated, screwed down for high pressure , screwed both ends for iron pipe of 15mm bore complete all as specified and directed. |
| 84 | S&F vitreous china squatting pan, Orissa pattern, size 580 x 440mm white with integral foot rest, cast iron 'P' or 'S' trap of size 100mm, including provision of plain cement concrete bedding and connection to trap and to flushing pipe, anti syphonage pipe etc and making good the floors complete all a specified and directed |
| 85 | S&F vitreous china wash down water closet pan (pedestal pattern) of size 565x360x395mm white in colour including connection pipe to union of flushing cistern, inlet and overflow pipes, connecting only to flushing cistern, anti-syphonage pipe with PVC flush pipe of 32mm dia including plastic seat with cover, white in colour with mild steel chromium plated hinging and 'P' or 'S' trap device complete all as specified and directed |
| 86 | S&F 10 litres PVC, valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float 32mm PVC 'L' bend and handle including brackets complete all as specified and directed |
| 87 | S&F health faucet (ABS Body) mild steel chromium plated suitable for 8mm dia pipe with 1.00 metre long flexible tube and ABS wall hook including making connectios and fixed in position complete all as specified and directed. |
| 88 | S&F chromium plated toilet paper holder fixed to walls with chromium plated brass screws complete all as specified and directed. |
| 89 | S&F Vitreous china urinal of size 590x390x375mm, white including providing and fixing plugs, bedding urinal against wall in CM 1:2 securing urinal to plugs with & including 60 mm long brass screws, pointing around urinal back in cement, flush pipe, grating and union for discharge pipe and Brass chromium plated waste coupling 32mm bore, Waste pipe PVC 32mm bore complete all as specified and directed. |
| 90 | S&F Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimumweight 60gms) complete all as specified and directed . |
| 91 | S&F PVC (SWR) multi floor trap plain with grating having diameter of outlet 75 mm including jointing with solvent cement to waste pipe, laid in cement concrete 1:2:4 type B-1 complete all as specified and directed. |
| 92 | S&F PVC (SWR) floor trap plain with grating having diameter of outlet 75 mm including jointing with solvent cement to waste pipe, laid in cement concrete 1:2:4 type B-1 complete all as specified and directed. |
| 93 | S&F PVC (SWR) type B pipes, 75 mm bore, single socketed, in any length with rubber ring joints fixed to walls with nail at spacing of 1m center to center including stack clamp of GI flat 30mm wide 2mm thick complete all as specified and directed. |
| 94 | S&F PVC (SWR) type B pipes, 110 mm bore, single socketed, in any length with rubber ring joints fixed to walls with nail at spacing of 1m center to center including stack clamp of GI flat 30mm wide 2mm thick complete all as specified and directed. |
| 95 | S&F PVC (SWR) bends any radius, 110 mm bore complete all as specified and directed |
| 96 | S&F PVC (SWR) bends any radius, 75 mm bore complete all as specified and directed |
| 97 | S&F PVC (SWR), junction single, (single 'T') with access door equal or unequal for 110 mm bore complete all as specified and directed |
| 98 | S&F PVC (SWR) vent cowl 75 mm dia complete all as specified and directed. |
| 99 | S&F PVC (SWR) vent cowl 110 mm dia complete all as specified and directed. |
| 100 | S&F designed looking mirror of size exc 0.54 sqm but n. exc 0.75 sqm of selected quality 6mm thick glass, fixed to wall with chromium plated plugs with chromium plated brass screws and cup washers complete all as specified and directed. |
| 101 | M&L for preparation of new plastered/concrete surfaces of walls and applying two coats of cement base paint over one coat of wall care putty complete all as specified and directed . |
| 102 | M&L for preparation of new or previously untreated steel surface of any description over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed |
| 103 | M&L for framed work as in doors or gates,water tank staging,cooler stand,cattle fencing etc of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing using Fe 290 (Gde-E-165) complete. complete all as specified and directed . |
| 104 | M&L for reinforced concrete pipes class NP-2 laid and jointed complete with collar of size 150mm (internal dia) complete all as specified and directed. |
| 105 | M&L for Concrete bed to drain pipes of dia 150mm in cement concrete 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) including packing under and haunching against the sides of pipe after laid & tested including necessary formwork complete all as specified and directed. |
| 106 | M&L for plain cement concrete 1:2:4, type B-1 (using 20mm graded crushed stone aggregates) as in surface channel and drain including necessary form work complete all as specified and directed |
| 107 | M&L for providing precast cement concrete 1:2:4, type B1, (using 20mm graded crushed stone aggregates) as in landings, cover slabs (for man holes cover) and similar articles with plain faces set in cement mortar 1:4 complete all as specified and directed . |
| 108 | Taking down carefully existing aluminium/copper point wiring for light, fan, socket or power bell complete with fittings such as Switches, sockets, ceiling roses, holders, call bells etc & making good the disturbed surfaces of walls/ceiling, matching the colour with existing surface complete all as specified and directed.Note : Rate for making good shall be deemed to be included in above item rate |
| 109 | Taking down of unserviceable MCB DB, SPN /TPN along with MCB's complete all as specified and directed. |
| 110 | Taking down of unserviceable sub main wiring of any size complete all as specified and directed. |
| 111 | Point wiring complete with 1.5 sqmm single core PVC insulated unsheathed cable(ISI marked) 1100 volts grade FRLSH with multistranded copper conductor, drawn through concealed / surface in wall / roof/ceiling surface and its accessories on the surface etc including PVC rigid concealed conduit of suitable size with all accessories such as bend, reducers, MS hooks including modular galvanised flush boxes of suitable size and white cover plate with frame as per relevant IS for mounting modular switches, sockets, fan regulators etc including continuous earth wire of size 1.5 Sqmm PVC FRLSH stranded copper conductor unsheathed, insulated, stranded connected to common earth point dolly for one light point/fan point/call bell point, 230 volts controlled by one switch complete all as specified and directed . Note:- Proper colour coding is to be followed as per IS specifications. |
| 112 | All as per srl item No 111 above but One 3 pin socket outlet 6 amp independent complete all as specifieds and directed. |
| 113 | All as per srl item No 111 above but One 3 pin socket outlet 6 amp same board complete all as specifieds and directed. |
| 114 | All as per Srl item No 111 here-in-before but for one 3 pin socket outlet 16 Amp independent with cable of size 2.5 Sqmm for point wiring and 2.5 sqmm as in continuous earth wire complete all as specified and directed |
| 115 | S&F modular type switch, one way 6 Amps,1 module complete all as specified and directed |
| 116 | S&F modular type socket 3 pin, 6 Amps, 2 module complete all as specified and directed . |
| 117 | S&F modular type switch, one way 16 Amps, 1 module complete all as specified and directed . |
| 118 | S&F modular type socket 3 pin, 6 A/16 Amps 2 module complete all as specified and directed . |
| 119 | S&F ceiling rose, surface backelite, two/three terminal, 240 volts complete all as specified and directed . |
| 120 | S&F LED light fitting 1 x 18Watt, 220V, Integrated batten type with driver, holder including LED tube light, connecting up with three core flexible copper conductor cable of suitable size from ceiling rose with all fixing arrengenment complete all as specified and directed. |
| 121 | S&F energy saving new generation 10W LED bulk head luminaire with opal diffuser, IP 65 and including connecting up with twin core twisted flexible copper coductor cable with suitable size of 230 volt,50 Hz complete all as specified and directed. |
| 122 | S&F Sheet metal enclosure for DBs,SPN, double door,IP-43 protected, 230 Volts,8 ways with 100 amps rated copper bus bar complete all as specified and directed . |
| 123 | S&F MCB SPN, 32 Amp, 240 Volts with rupturing capacity 10 KA, 'C' series, complete all as specified and directed . |
| 124 | S&F MCB Single pole, 6 to 32 Amp, 240 Volts with rupturing capacity 10 KA, 'C' series, complete all as specified and directed . |
| 125 | S&F Submain wiring with two runs of single core PVC FRLSH unsheathed, insulated, copper cable of 6 Sqmm size, multi stranded, 1100 volts grade with PVC insulated,unsheathed FRLSH copper wire 6 Sqmm for continous earth wire drawn into and including concealed PVC conduit of suitable size complete all as specified and directed . Note :- Two runs of 6 Sqmm copper cable and one run of 6 sqmm copper wire earth continuty conductor in conduit with accessories shall be measured as one length) |
| 126 | Taking down ceiling fan of any size , dismantling blades and removing fan for depositing in MES Store Yard complete all as specified and directed |
| 127 | S&F ceiling fan complete with blades,clamp, hooks,down rod of suitable size and accessories, 230 V, 1200 mm sweep, min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor(BLDC) with compatible regulator and fixing of hooks by anchor fastner including connecting from ceiling rose/connector with & including flexible copper cable of suitable size complete all as specified and directed . |
| 128 | M&L for complete earthing with galvanised mild steel earth plate electrode of size 600x600x6mm thick, burried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the earth plate not less than 1.5 mtr below ground level connected to galvanised earth lead wire 4mm dia (8 SWG) by means of nut, bolt, check nuts and washer of galvanised iron including PCC pit in PCC 1:2:4 type B-1, precast RCC cover slab using reinfocement with XPM weighing not less than 1.87 kg/Sqm with suitable handle made of 12mm round bar including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube for watering with one end fixed with cast iron funnel and wire mesh ,15mm dia light grade galvanised steel tubing upto 7.5 m length for drawing earth lead wire protection, common salt, charcoal, etc complete all as shown in electrical plate No 3 of SSR Part-I and testing on completion complete all as specifieds and directed . |
| 129 | S&F exhaust fan, steel body, AC single phase. 230 V of size 300 mm sweep with, blades and frame and louvers, hanging on wall with 4 Nos steel fasterners 10mm dia & 100mm long including wall hole and making good the disturbed surfaces as per existing complete all as specified & directed |
| 130 | Supply, laying, jointing, testing and commissioning of Low Tension (LT) XLPE insulated, armoured, heavy duty, electric power cable, cross sectional area 50 Sqmm, 3.5 core, aluminum conductor, 1100 volts grade under ground cable including both side connection with lugs/thimbles of suitable size etc, laid in trenches, along poles or passing through pipes or laid under floor or through walls etc, complete including taking out old cable & bricks all as specified and directed. Note: (i) Returning filling, earth work, sand cushioning and cable cover for protection of cable shall be measured and paid separately. |
| 131 | M&L for sand cushioning with a layer of dry river sand, 80mm thick before laying of cable and 150mm thick (punned down to 100mm thick) after laying of cables, in trenches/ducts, complete all as specified and directed. Note : Punned down thickness (overall 18cm), shall be considered for measurement and payment. |
| 132 | M&L for factory made unreinforced precast concrete cable cover LV type-1, flat, of size 250x150x40mm, laid flat and dry in trenches over the cable for protection, length perpendicular to the direction of cable adjacent to each other, complete all as specified and directed. |
| 133 | S&F Galvanised steeI tubing, light grade, 40mm bore, for cable protection, fixed to pole/wall with MS clamps, nuts, bolts etc or laid under floor/road/pavement complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 08, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 29, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedAug 31, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 1 dayTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender