Tender For Provision Of Parking Shed With Hard Standing For Ops Complex At Bhisiana Under Ge (Af) Bhisiana
Tender Value
3.50 Lakhs
Estimated cost
Bid Submission
27 Aug 2026
14 days left
EMD
70000
Bank guarantee accepted
Document Fee
300
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Bathinda → Punjab
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Provision Of Parking Shed With Hard Standing For Ops Complex At Bhisiana Under Ge (Af) Bhisiana
BOQ
| Sl. No. | Item Description |
| 1 | Surface dressing not exceeding 15cm deep in soft/ loose soil including cutting of grass, roots, bushes and removing from site all grass, roots and extra soil if any complete all as specified and as directed. |
| 2 | Excavation in trenches (Manual), not exceeding 1.5m wide and not exceeding 1.5m in depth for foundations of shafts, wells, cess pits, manholes, pipe line, cable in trenches etc., not exceeding 10 Sqm on plan and getting out in any type of soft including trimming the sides and forming bottom surfaces to required levels complete all as specified and as directed. |
| 3 | Returning, filling including spreading, leveling watering and well ramming in layers not exceeding 25cm thick in soft/loose soil complete all as specified and as directed. |
| 4 | Removing excavated material (surplus soil) to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and as directed. |
| 5 | Excavation in post holes in soft/loose soil n. exc 0.50 cum each, getting out, returning filling in and ramming earth or broken rubble mixed with earth around, in layers n. exc 25 cm including removing of surplus spoil to a distance n exc 50 mtr and making good the disturbed surfaces all as specified and directed by Engineer-in-Charge. |
| 6 | Material and labour for PCC (1:2:4) type B-1 using 20 mm graded crushed stone aggregate as in foundation filling, in post hole, bed block, around the poles/stay, coping/Pedestal of pole, etc & similar work including necessary form work, finishing the exposed surfaces of the concrete even & smooth without using extra cement, complete all as specified and as directed. |
| 7 | Material and labour for brick work with sub class ‘B’ old size burnt clay bricks, straight or curved on plan exc. 6 metre mean radius built in cement mortar (1:6) complete all as specified and as directed by Engineer-in-charge. |
| 8 | Material and labour for 15mm thick cement plastering in cement mortar (1:4) on any face of Brick walls or concrete surfaces, finished even and fair complete all as specified and as directed. |
| 9 | Material and labour for hard core of broken stone or boulders of gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface complete all as specified & directed by Engineer-in- charge. |
| 10 | Material and labour for PCC ( 1:4:8), type D-2 using 40 mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and as directed |
| 11 | Material and labour for 100mm thick cement concrete ( 1:4:8), type D-2 using 40 mm graded stone aggregate as in sub base complete all as specified and as directed. |
| 12 | Supply and laying/fixing 60mm thick factory made chamfered edge cement concrete paver block/ interlocking tile of M-35 grade, prepolished & preglazed, with approved colour, design & pattern (laid in required colour & pattern as directed) as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 30mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand, finishing and sweeping extra sand complete all as specified and as directed. |
| 13 | Material and labour for mild steel framed structural work comprising angle iron vertical posts, columns, main beams, cross beams, rafters, purlins, bracings, tie members, frames for sunshades/chajjas, parking sheds, canopies, platforms, walkways, steel gate and other similar works, fabricated from rolled mild steel joists, channels, angles, tees or other rolled steel sections, together with gusset plates, base plates, cleat plates, rails, braces, round bars, stiffeners and other connecting plates, conforming to Grade Fe-410-W (Grade E-250 Quality A). The work shall include cutting, bending, notching, coping, drilling, punching, shaping, edge preparation, welding, grinding of welds, fabrication, shop assembly, transportation, erection, alignment, plumbing and fixing in position with approved holding-down bolts, anchor fasteners, nuts, bolts, washers and all necessary fixing accessories. The item shall include all labour, materials, welding electrodes, gas cutting, scaffolding, staging, lifting arrangements, tools and plant, consumables, safety measures and all incidental works necessary for satisfactory completion of the work at all locations up to a height of 5.00 metres above the existing ground level or any accessible roof, floor, platform or balcony level, complete in all respects, as specified and directed by the Engineer-in-Charge. |
| 14 | Material and labour for preparation of new steel and iron surfaces of any description, not otherwise described, exceeding 10 cm in width or girth, including cleaning the surface free from dust, dirt, grease, oil and other foreign matter and surface imperfections by rubbing down with emery paper/sand paper or by other approved means to obtain a clean, smooth and even surface and further applying one coat of red oxide zinc chromate primer and two coats of first-quality synthetic enamel paint of approved brand, shade and tint, each coat applied by brush only after proper preparation and complete drying of the preceding coat, to produce a smooth, uniform, durable and aesthetically acceptable finish, complete in all respects as specified and directed by the Engineer-in-Charge. |
| 15 | Material and labour for Providing and fixing pre-painted galvalume hot-dip aluminium–zinc alloy metallic coated corrugated steel sheets (profiled) of any approved profile/pattern, 0.50 mm thick (BMT), coating class AZ150, conforming to IS 15965:2012, durability class 3 and atmospheric classification category C3, factory pre-painted in an approved colour and having a minimum yield strength of 550 MPa. The sheets shall be used for roof covering, chajjas, and shall be fixed to the existing/proposed supporting structure with approved self-drilling screws complete with suitable corrosion-resistant washers, including all necessary end and side laps, cutting, bending, folding, drilling, fitting, alignment, levelling and making good. The item shall also include all necessary scaffolding, staging, ladders, working platforms, lifting arrangements, tools, tackles and safety/fall-protection measures required for execution at any floor level or height, complete, all as specified and as directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 08, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 27, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 14 daysAug 29, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 16 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender