Tender For Providing New 5Kl Bmc Shed Work At Muthandipatty Mpcsin Thanjavur Union, Thanjavur District.
Tender Value
9.41 Lakhs
Estimated cost
Bid Submission
25 Aug 2026
2 days left
EMD
9500
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Thanjavur → Tamil Nadu
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Providing New 5Kl Bmc Shed Work At Muthandipatty Mpcsin Thanjavur Union, Thanjavur District.
BOQ
| Sl. No. | Item Description |
| 1 | Earth work excavation for foundation (for narrow excavation) in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and refilling the sides,cleaning and leveling the site, etc., complete complying with standard specification. |
| 2 | Supplying and filling with M-Sand for basement to required thickness, watered, well rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers. |
| 3 | Supplying and filling with gravel for foundation and basement to required thickness, watered, well rammed and consolidated, etc., completed as directed by the departmental officers. |
| 4 | Plain Cement Concrete 1:5:10 (One Cement, Five M-sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation and flooring the top surface rough to receive the floor including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification. |
| 5 | Brick work in Cement Mortar 1:5 (one part cement and five parts M-sand) using best quality II class Ground moulded chamber burnt bricks of size 9\\" x 4-1/2\\" x 3\\" to line, level and to plumb on one face including necessary scaffolding, racking out joints, curing etc., complete as directed by the departmental officer and as per standard specification.- for Foundation and Basement |
| 6 | for above basement up to 4.50m ht. |
| 7 | Supplying , erection and steel centering for all RCC works using M.S Sheet, M.S. angles casurina props C.W.joints for all type of RCC works (ie) beams, roof slab, lintel, column footing, column & roof beam etc., including necessary supports with all cross bracing, filling the slits and holes the reprieved materials should be taken by the contractor and side shuttering etc., complete as directed by the departmental officers.Up to basement-Column surface |
| 8 | Plain surface |
| 9 | above basement level 3.30m heigh- Column surface |
| 10 | Reinforced Cement Concrete 1:2:4 (One Cement, Two M-sand and Four hard broken stone jelly) using 20 mm gauge machine crushed hard broken granite stone jelly for all RCC items of works excluding cost of reinforcement grill and fabricating charges, centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc. complete complying with standard specification and as directed by the departmental officers - for Foundation and Basement |
| 11 | Above basement up to 4.50m ht |
| 12 | Supplying, fabricating and placing in position of reinforcement, grills for all RCC works including cost of steel and binding wire , cutting and tying etc., complete as directed by the departmental officers. |
| 13 | Supplying and fixing of cuddapah slab 38 / 40mm thick including cutting and polishing on both side etc.,complete complying with standard specification and as directed by the departmental officers. |
| 14 | Supply and laying Shahabad stone slabs with machine cutting edges in cement mortar 1:3, 20 mm thick 0.6X0.6M etc complete |
| 15 | Supplying and laying of flooring stone(not less than 10cm tk) flooring at milk unloading platform with base morter of 1:5,Including cost and conveyemce of all charges etc,.comleted |
| 16 | Supplying and fixing of steel rolling shutter (pull and push type)with ISI make of approved quality with MS lathes 75mm wide and 18 gauge GI sheet thick to a different sizes including all accessories like sliding groves, shafts, springs, bearings, hood and locking arrangements and grouting the side and top assembly with walls and beams etc. complete and as directed by the departmental officers. |
| 17 | Fabricating, Supplying and fixing in position of steel sheeted windows ( Three Leaves) with the following specifications. Outer frames of windows made of 'Z' section F7D of size 33 x 25 x 3mm at 1.419 kg/ m and mullion 'J' section (F4B) of size 46x25x3mm at 2.28kg/m and shutter section of made of F7D of 33x25x3mm at 1.419 kg/m as specified in IS 7452/1990. Each openable shutter should not exceed a width of 600mm to enable separate operations and easy maintenance. The panel of the shutters to be covered with 18 gauge cold rolled sheet of superior quality and welded intact with shutter frames. Horizontal stiffeners using 18x5mm MS Flat at 0.70kg/m at 3 Nos. for each shutter and additional diagonal stiffeners of the same MS flats at all the four corners of each shutters to the suitable length welded to the shutters, for holding the CR Sheets in position firmly etc complete as directed by the departmental officers. |
| 18 | fabricating, Supplying and fixing in position of mild steel (RHS) Rectangular steel hollow section following thickness and M.S channel sizes of 150mmx75mmX5.7mm thickness for loading dock area including cutting, welding and fixing in purlin etc., completed as directed by the departmental officers. |
| 19 | Supplying and fixing in position of Powder coated galvalume colour sheet of 0.47mm thickness with necessary bolts, nuts and washers, metal screws etc. complete with standard specification and as directed by the departmental officers. |
| 20 | Plastering with Cement Mortar 1:5 (One cement and Five P-sand), 12mm thick in all floors including curing and scaffolding etc. complete complying with standard specification and as directed by the departmental officers. |
| 21 | Plastering with Cement Mortar 1:3 (One Cement and Three P-Sand) 20mm thick mixed with water proofing compound conforming to BIS at 2% by weight of cement used including finsihing, curing, etc., complete in all floors complying with standard specification and as directed by the departmental officers. |
| 22 | Supplying and fixing in position CI manhole covers with CI frames (Heavy duty) of size 60cm x 60cm of best approved quality as directed by the departmental officers with standard specifications. |
| 23 | Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification. |
| 24 | Painting two coats of new iron work using ready mixed synthetic enamel paint of approved quality and colour over a priming coat etc. complete as directed by the departmental officers. (such as steel window, Grill , M.S Channel & rolling shutter ets.,) |
| 25 | Supplying and fixing of weld mesh at 7.50cmx5.0cmx6mm thick 10 gauge with 35mmx35mmx6mm angle.Including cost and conveyence of all charges etc,..completed |
| 26 | GST (Note: The tenderer should quote the amount towards Goods and Service tax (GST) in the appropriate columns in terms of percentage (%). If not quoted, it will be considered that the rate quoted is inclusive of GST.) Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 10, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 25, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 2 daysAug 27, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 4 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender