Tender For Construction Of Patwar Khan At P.H Nangali Haveli(Under Capex Budget(Revenue) 2026-27). Aaa:-District Development Commissioner Poonch Vide Order No 59 Ddcp Of 2026,Dated 01-08-2026
Tender Value
8 Lakhs
Estimated cost
Bid Submission
21 Aug 2026
11 days left
EMD
16000
Bank guarantee accepted
Document Fee
600
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Poonch → Jammu and Kashmir
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of Patwar Khan At P.H Nangali Haveli(Under Capex Budget(Revenue) 2026-27). Aaa:-District Development Commissioner Poonch Vide Order No 59 Ddcp Of 2026,Dated 01-08-2026
BOQ
| Sl. No. | Item Description |
| 1 | Removal of unhygienic materials (so classified by the site engineer) from designated sites and its disposal as per directions, all inclusive. |
| 2 | Earth work in bulk excavation by mechanical means (hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m Sq. on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge. All kinds of soil : |
| 3 | Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed:All Kind of Soil |
| 4 | Dumping stone including cost of stones. On Horizontal on level. |
| 5 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with:1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) |
| 6 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with:1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) |
| 7 | Providing and laying damp-proof Course 50 mm thick with cement concrete 1:2:4 (1 cement:2 coarse sand: 4 graded stone aggregate 20 mm nominal size) and curing complete |
| 8 | Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation/plinth & superstructure above plinth level upto floor five level including curing in : Cement mortar 1:6 ( 1 cement : 6 coarse sand) |
| 9 | Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°,landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering,finishing and reinforcement with 5.3.1 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 10 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 11 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades,laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete.Size of tile 600x600 mm |
| 12 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shadesexcept burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement :3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 13 | Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, laid on 20 mm thick cement mortar 1:4 (1Cement : 4 Coarse sand), including grouting the joints with white cement and matching pigments etc., complete.In colour such as White, Ivory, Grey, Fume Red Brown |
| 14 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately):Sal wood |
| 15 | Providing and fixing 35mm thick panelled or panelled and glazed shutters for doors,windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note: -Butt hinges and necessary screws shall be paid separately).First class kail wood |
| 16 | Providing and fixing 12mm thick specified board medium density exterior grade (Grade I) to frame, backing or studding with screws etc. complete (Frames, backing orstudding to be paid separately) :Flat pressed 3 layer particle board or graded wood particle board IS:3087 |
| 17 | Providing and fixing 30mm thick glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes including ISI marked M.S. pressed butthinges bright finished of required size with necessary screws.Second class deodar wood |
| 18 | Providing and fixing 35mm thick wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge :First class kail wood |
| 19 | Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete:2nd class teak wood.50 x 12 mm |
| 20 | Providing and fixing ISI marked aluminum butt hinges ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :100x75x4 mm |
| 21 | Providing and fixing aluminum sliding door bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete : 250x16 mm |
| 22 | Providing and fixing aluminum tower bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :150x10 mm |
| 23 | Providing and fixing aluminum tower bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete.100x10 mm |
| 24 | Providing and fixing aluminum handles ISI marked anodized (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with necessary screws etc. complete.125 mm |
| 25 | Providing and fixing aluminum handles ISI marked anodized (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with necessary screws etc. complete.100 mm |
| 26 | Providing and fixing aluminum hanging floor door stopper, ISI marked,anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : Twin rubber stopper |
| 27 | 15mm Cement plaster on the rough side of single or half brick wall of mix: 1 : 6 ( 1 cement : 6 fine sand) |
| 28 | 6 mm cement plaster to ceiling of mix 1 : 3 (1 cement : 3 fine sand) |
| 29 | Providing and applying white cement based putty of specified thickness,of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.2 mm thick |
| 30 | With ready mixed pink or grey primer of approved brandand manufacture on wood work (hard and soft wood) |
| 31 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade on New work (two or more coats) over and including priming coat with water thinnable cement primer |
| 32 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade.Two or more coats on new work |
| 33 | Centering and shuttering including strutting, propping etc. and removal of form for: |
| 34 | Foundations, footings, bases of columns etc. for mass concrete. |
| 35 | Suspended floors, roofs, landings, balconies and access platforms. |
| 36 | Edges of slabs and breaks in floors and wallsUnder 20 cm wide |
| 37 | Wiring for light Point/Fan point/Call bell Point with 1.5sqm FRLS PVC insulator Copper conductor single core cable in recssed /surface medium class PVC conduit with modular switch ,modual plate suitable size of GI Box and earthing the point with 1.5 sqmm FRLS PVC Insulator copper conductor single cor cable etc As required |
| 38 | Providing and fixing of Ceiling Fan 1200mm |
| 39 | Providing and fixing of Exhaust Fan |
| 40 | Providing and fixing of CFL Lights |
| 41 | Providing and fixing of Supply Line 1600mm |
| 42 | Providing and fixing of Main Board 4 way Single Pole |
| 43 | Carriage of material by M.T incl loading/unloading & stacking complete |
| 44 | Sand for Brick work and Plaster avg. lead 220 km by MT |
| 45 | Sand /Stone agg. below 40 mm nominal size avg. lead 05km by MT |
| 46 | Bricks for an avg. lead 225 km by MT |
| 47 | PLUMBING SYSTEMSUB HEAD -I :SANITARY FIXTURES |
| 48 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 liter low level white P.V.C. flushing cistern, including flush pipe with manually controlled device (handle lever), conforming to IS:7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:W.C. pan with ISI marked white solid plastic seat and lid. |
| 49 | Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required : White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar taps. |
| 50 | Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. |
| 51 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps,including cutting and making good the walls etc.:Internal work-Exposed on wall.Medium |
| 52 | 15 mm dia. nominal bore |
| 53 | 20 mm dia. nominal bore |
| 54 | 25 mm dia. nominal bore |
| 55 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing. Rectangular shape 453x357 mm |
| 56 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank |
| 57 | Providing and fixing following PVC fitting of appeoved quality as vectus or price |
| 58 | PVC Pipe 100mm dia |
| 59 | PVC Pipe 65mm dia |
| 60 | Floor Trap 65mm x100mm dia |
| 61 | PVC Plane band 100mm |
| 62 | PVC P band 65mm |
| 63 | PVC D band 65mm |
| 64 | PVC P.Tee 100mm |
| 65 | PVC D.Tee 100mm |
| 66 | PVC P.Trap 100mm |
| 67 | PVC P.Tee 65mm |
| 68 | PVC D.band 100mm |
| 69 | PVC Clamp 100mm |
| 70 | Providing and fixing following C.P fitting of approved quality |
| 71 | Supply and fixing of CP bib Cock (long nose) |
| 72 | Supply and fixing of CP Short body |
| 73 | Supply and fixing of CP Soap Dish |
| 74 | Supply and fixing of CP waste cuppling 4\\" |
| 75 | Supply and fixing of Grating lock plane |
| 76 | Supply and fixing of Grating lock hole |
| 77 | Supply and fixing angle valve |
| 78 | Supply and fixing CP nipple 1/2\\" |
| 79 | Supply and fixing CP nipple 1\\" |
| 80 | Supply and fixing PVC connection |
| 81 | Supply and fixing waste pipe |
| 82 | Supply and fixing BAL Bal 40mm |
| 83 | Supply and fixing union 15mm |
| 84 | Supply and fixing full thread nipple (Tank Nipple) union 15mm |
| 85 | Supply and fixing brass Bal Bal 25mm Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 08, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 21, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 11 daysAug 22, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 12 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender