Tender For Addition/Alteration/Improvement To Certain Watch Towers At Darjipura Alongwith Provn Of Grease Trap For Airmen Mess At Afs Deesa Under Ge (Af) Baroda
Tender Value
23.78 Lakhs
Estimated cost
Bid Submission
22 Aug 2026
10 days left
EMD
47560
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Vadodara → Gujarat
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Addition/Alteration/Improvement To Certain Watch Towers At Darjipura Alongwith Provn Of Grease Trap For Airmen Mess At Afs Deesa Under Ge (Af) Baroda
BOQ
| Sl. No. | Item Description |
| 1 | Taking down chokwats or frame exc 1.5 Sqm and n exc 4.0 Sqm each (without taking off shutter from the fram) complete all as specified and directed. |
| 2 | Taking down chokwats or frame exc 1.5 Sqm each (without taking off shutter from the fram) complete all as specified and directed. |
| 3 | Taking down shutter only of any description exc 1.0 Sqm n exc 2.0 Sqm and removing complete all as specified and directed. |
| 4 | Taking down shutter only of any description n exc 1.0 Sqm and removing complete all as specified and as directed |
| 5 | M&L 35mm thick 2nd class hardware glazed and skeleton shutter open rebeted and prepared to receive glass gauze etc (withou shash bar) edges of framing plain chamfeted or runded filled with cut and mtered beads for securing, glass etc size of member of shutter as per specifed in SSR Part-I section 8, clause 8.24(a) supplyed and fitted to chowkats and directed |
| 6 | M&L factory made flush shutters 35mm thick solid core construction, with block board core and plywood face panels, commericial type on both sides as in shuter complete all as specified as directed. |
| 7 | M&L factory made flush shutters 25mm thick solid core construction, with block board core and plywood face panels, commercial type on both sides as in CB shutter all as specified and as directed. |
| 8 | M&L pressed steel frames (125 x 60) for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. complete all as specified |
| 9 | M&L PCC 1:2:4 Type B-O using 12.5 mm graded aggregate for filling of pressed steel door frame complete all as specified and directed. |
| 10 | M&L framed work ( Fe 290 gde E165) as in doors or gates of angle or other section with gusset plates, rails, braces, etc, complete, drilled for fixing of steel sheeting or other covering. Doors, etc to be prepared for hanging or sliding with and including either hooks and butt hinges or steel hanging door fittings sliding bolts, handles etc (exclusive of steel sheeting or other covering, running rails and uides) and hanging also fastening and fixing complete all as specified and as directed |
| 11 | S&F Mild steel, plain black sheet 1.6mm thick in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40mm lap joints with riveted or welded seams, including bending or turning up, mitered angles, etc. as required complete all as specified and directed |
| 12 | M&L for cutting holes in brick wall for inserting hold fast etc, built in CM of depth of embedded portion exc. One brick but n. exc. Two brick thick wall including making good dismantled portion in cement mortar in (1:3) or PCC (1:2:4) type B1 complete all as specified and directed. |
| 13 | S&F 75mm long SS heavy weight butt hinges and fixed to frame with screwed or welding complete |
| 14 | S&F 100mm long SS heavy weight butt hinges and fixed to frame with screwed or welding complete |
| 15 | S&F aluminum alloy anodized sliding door belt with haps and staple (bolt type) and fixing clip of sheet cast or extruded section or cast aluminum alloy and fixed length of bolt 200mm |
| 16 | S&F for 200mm long aluminum anodized barrel tower bolts of extruded section and fixed complet all as specified and directed |
| 17 | S&F for 150mm long aluminum handle cast type anodized complet all as specified and directed |
| 18 | S&F in door stopper of aluminum alloy body and tongue double legged anodized with hard draw steel spring over all length of cover plate 150mm fixed in floor complete all as specified and directed. |
| 19 | S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed |
| 20 | S&F 4mm thick figured glass pin headed type and glazing with oil putty in squares not exc 0.5sqm in each pane including taking down existing broken glass from metal frames complete all as specified and directed. |
| 21 | M&L for taking down steel window shutters of any description n exc 1 Sqm including removing of old hinges and reflexing the shutters in same opening with new hinges ( 2 or 3 Nos) properly welded with frame, this job shall be included with all required material and tools/ resources to the satisfaction of EIC complete upto 2nd floor height all as specified and directed |
| 22 | M&L for repair of steel window shutters hinges of any description with oiling, welding and hinges or material and tools required for this job to the satisfaction of EIC complete upto 2nd floor height complete all as specified and directed |
| 23 | S&F in repair stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed |
| 24 | S&F 4mm thick sheet glass, ordinary quality and glazing with oil putty in squares not exc 0.5 sqm in each pane including taking down existing broken glass from metal frames complete all as specified and directed. |
| 25 | Dismantling floor, hearth or wall tilling including cement mortal bedding, (but not backing) removing serviceable tiles to store and rubbish off the premises |
| 26 | M&L Non skid coloured ceramic tiles 7 to 8m thick (Square/ Rectangular) area of each tiles exc. 0.11 sqm but not exc. 0.18 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed 20mm thick in CM 1:4 as bedding layer for floor finishes. |
| 27 | M&L glazed ceramic coloured tiles in vertical surface such as dado/ skirting etc 450x300x7mm thick set and jointed in neat cement slurry point in white or colour cement to match over and including 10mm thick rendering in CM 1:4 as backing coat complete all as specified and directed |
| 28 | Demolition of concrete in ground floors and pavings n exc 15mm thickness (below or above ground level) complete all as specified and directed |
| 29 | M&L 75mm thick PCC (1:3:6) type C2 using 40mm grade stone aggregate as in plinth protecting and finished even and smooth without using extra cement |
| 30 | M&L for cement concrete Type D2 1:4:8 (40mm graded aggregate) as in, foundation fillig and mass concrete similar work complete all as specified and directed |
| 31 | M&L for 100mm thick cement concrete type B-2 1:2:4 (40mm graded aggregate) as in flooring, finishing cement concrete surface even and smooth without using extra cement for path all as specified |
| 32 | S&F in repair vitreous china squatting pan, Orissa pattern, size 580 x 440mm white, with integral foot rests ( excluding flushing cistern and flush pipe) complete all as specified and directed. |
| 33 | S&F in repairs, PVC flushing cistern symphonic action type, low level 10 liter capacity incl flush pipe and all accessories |
| 34 | S&F PVC (SWR) ‘P’ trap of 110mm |
| 35 | S&F in repair PVC (SWR) floor trap plain with grating including jointing with solvent cement of 75mm dia |
| 36 | S&F bib tap cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for union pipe or brass ferrule and fixed to 15mm dia pipe complete all as specified and directed. |
| 37 | S&F in repair vitreous china wash basin (WHB), white bowl type size 550mm x 400mm (approx.) excluding supply of taps, but including waste pipe 1mtr long and waste fittings brass chromium plated for glazed basins etc. with long screw shanks and fit nuts, flange end embedded in red lead cement and other end fixed, chain and plug and porcelain stopper and brackets including cutting for and pinning in ends of brackets or erecting stand, making connections to waste and supply pipes and complete all as specified and directed |
| 38 | S&F pillar taps swan neck type cast copper alloy with capstan heads, chromium plated screwed down high pressure with or without lettered Hot or cold with long screwed shanks and flynuts, screwed for union pipe and fixed to 15mm dia pipe. |
| 39 | S&F PVC connections 15mm size with PTMT nuts of length 450mm |
| 40 | S&F in repair brass chromium plated shower rose 125mm size swivel type |
| 41 | S&F in repair 15mm dia angle valves cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed |
| 42 | S&F in repairs concealed type stop valves fancy type, chromium plated with long shank and cup cast copper alloy, screwed down, high pressure, screwed both ends for iron pipe or for unions and fixed to 15mm bore pipe complete all as specified and directed. |
| 43 | Demolition and breaking up drain pipes( CI drain pipes/ PVC/ AC or reinforced concrete) set in cement mortar (100mm dia), if required complete all as specified and directed |
| 44 | S&F 110mm bore PVC(SWR) pipes single socketed in any length with rubber ring joints fixed to wall or in trenches or in floor complete all as specified and directed |
| 45 | S&F 75mm bore PVC(SWR) pipes single socketed in any length with rubber ring joints fixed to wall or in trenches or in floor complete all as specified and directed |
| 46 | S&F 110mm bore PVC (SWR) branch piece, single (single Y) equal or unequal complete all as specified and directed |
| 47 | S&F 110mm bore PVC (SWR) reducers complete all as specified and directed |
| 48 | S&F 110mm bore PVC (SWR) couplers complete all as specified and directed |
| 49 | S&F 110mm bore PVC (SWR) bends any radius complete all as specified and directed |
| 50 | S&F soap dish, any type, fixed to plugs with chromium plated brass screws completed all as specified and directed |
| 51 | M&L for taking down steel tubing and connections 15mm dia including all fittings and fixture fixed to existing line completed all as specified and directed |
| 52 | M&L for taking down steel tubing and connections 20mm dia completed all as specified and directed |
| 53 | S&F 15mm bore GI tubes medium grade including all fittings of pressure rating 10kgf/cm2 fixed complete to walls. Ceilings or in floors etc. complete and making good the area to match with existing surface complete all as specified and directed |
| 54 | S&F 20mm bore GI tubes medium grade including all fittings of pressure rating 10kgf/ cm2 fixed complete to walls, ceilings or in floors etc, complete all as specified and directed |
| 55 | S&F in repairs tubular towel rail brass chromium plated, 20mm dia 600mm long completed all as specified and directed |
| 56 | S&F 600x450mm beveled edge mirror of selected quality glass mounted on PVC sheet/ commercial ply/ AC board with PVC molded all around beading and fixed to wooden plugs with chromium plated brass screws and cup washers |
| 57 | Dismantling water tanks exc 200 Ltr & n exc 500ltr capacity and removing to store |
| 58 | S&F 500ltr rotational molded polyethylene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position completed all as specified and directed |
| 59 | S&F 20mm ball brass valves, high pressure with polythene float and flynut complete screwed for iron or brass ferrule and fixed |
| 60 | Taking down cement plastering of any description on brick/ stone/concrete wall/ ceiling surfaces of any description incl racking out joints hacking for key, scrubbning down with water etc. |
| 61 | M&L rendering 10mm thick on fair faces of brick or concrete surfaces in CM 1:6 and finished even and smooth without using extra cement |
| 62 | M&L rendering 15mm thick on fair faces of brick or concrete surfaces in CM 1:4 finished fair and even complete all as specified and directed. |
| 63 | M&L rendering in CM 1:3:, 5mm thick on concrete surfaces as in ceiling, finished fair and even complete all as specified and directed |
| 64 | M&L for preparation of new surfaces of walls and applying two coats of oil bound distemper over a chalk whiting, on plastered surfaces, preparatory to distempering complete all as specified and directed |
| 65 | M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and as directed |
| 66 | M&L preparation of newly plastered surfaces and priming with alkali resistant priming paint and painting with two coats of exterior ACRYLIC emulsion paint (Colour or shade as approved by GE) in camouflage pattern over and including a coat of primer complete all as specified and directed |
| 67 | Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for and removing debris out of MD land complete all as specified and directed. |
| 68 | M&L for reinforced cement concrete (design mix) (M-25) using 20mm graded stone aggregate as spiral stair case including landings complete all as specified and directed. |
| 69 | M&L for TMT bars 10mm dia and over cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia |
| 70 | M&L for TMT bars 6mm to 8mm cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia |
| 71 | M&L for formwork for fair finished surfaces to spiral staircase with slopping or stepped soffits, inclining risers and stringers (excluding landing) complete all as specified and directed |
| 72 | M&L for formwork for fair finished surfaces to edges of concrete treads, horizontal or sloping and similar work exc 5cm but not exc. 10cm wide complete all as specified and directed |
| 73 | M&L for rendering 10mm thick in CM 1:4 on fair faces of brick work or concrete surfaces complete all as specified and directed |
| 74 | Dismantling wrought iron or mild steel work of any description not otherwise provided for |
| 75 | Fixing only framed work such as grills, gratings etc. with ends of bars shouldered and or riveted or forged into spikes framed guard bars barred iron doors ladders framed balusters walk ways railings framework of water tanks and similar work conforming to Fe 290. Gde—E-165 complete all as specified and directed. |
| 76 | M&L for MS framed work such as grills, gratings etc. with ends of bars shouldered and or riveted or forged into spikes framed guard bars barred iron doors ladders framed balusters walk ways railings framework of water tanks and similar work conforming to Fe 290. Gde—E-165 complete all as specified and directed. |
| 77 | M&L for preparation of new surfaces of steel or iron over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer completer all specified and directed |
| 78 | M&L for preparation of old painted steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint completer all specified and directed |
| 79 | M&L for preparation of new wooden surface of any description not otherwise described over 10cm width or grith and applying two coats of synthetic enamel paint over one coat of pink primer |
| 80 | M&L for preparation of old painted surfaces of wood and wood based material of any description over 10cm width or girth and applying one coat of synthetic enamel paint completer all specified and directed |
| 81 | M&L for complete removal of existing treatment and applying three coats of white wash on ceiling surface completer all specified and directed |
| 82 | M&L for preparation of old decorated surfaces of wall rubbing down and applying two coat of oil bound distemper completer all specified and directed |
| 83 | M&L for complete removal of loose/ cracked, spalled concrete upto depth of the reinforcement rods or depth of carbonation incl reinforcement if required from existing surfaces of RCC members like roof projection, chajjas, beams, columns, staircase etc and cleaning of the reinforcement bars and exposed concrete surfaces of RCC members by chipping, wire brushing emery sheets etc and provide required reinforcement by welding/ binding to connect or overlap with existing reinforcement and application of zinc primer on all sidesof the reinforcement and application of epoxy bonding agent to exposed old concrete surfaces and pouring / pumping micro-concrete mix as per relevant ASTM/BS/IS having compressive strength of 45mpa at 2 days of make pidilite/ BASF/ Sila/ Forsoc or equivalent in RCC members which shall be pre-packed single component, chloride free, Non shrink, free flow, slef compacting and mixed as per manufactures specifications, including required leak proof shuttering, presoaking of substrate, manual application . |
| 84 | Taking down carefully point wiring including (light, fan, socket or power complete fittings, such as switches, ceiling roses, pendant holders, Batten holders, shades conical fan regulators, light or power sockets etc) removing materials from site and making good disturbed surfaces of walls roofs etc all as directed. |
| 85 | Taking down carefully Sub main wiring complete including removing materials from site and making good disturbed surfaces of walls roofs etc all as directed. |
| 86 | M&L for Point wiring complete as specified with 1100 volt grade 1.5 sq.mm. (nominal area) single core PVC insulated unsheathed (FRLS) cable multi-stranded copper conductor drawn through existing rigid non-metallic PVC concealed conduit of suitable size but not less than 20mm dia, with all fittings, concealed in wall/roof /floor including decorative modular cover plates (inner and outer) suitable for housing modular pattern switches/ sockets/ regulators etc. along with necessary metal boxes flush mounting in the wall duly earthed with same cable as for wiring above but green in colour as continuous earthing wire complete all as specified for :- |
| 87 | (a)One light point controlled by one one/way switch. |
| 88 | (b)One Fan/Ex fan point controlled by one one/way switch. |
| 89 | (c) One 3 pin 5 Amps socket outlet on same board with other switch. |
| 90 | (d) One 3 pin 5 Amps socket outlet on independent board with other switch. |
| 91 | (e ) One bell point controlled by one one/way switch. |
| 92 | (f) One light point controlled by one two/way switch. |
| 93 | All as per item No.2 above but wiring with 2.5 sqmm multistranded copper conductor unsheathed and 2.5 sqmm copper conductor unsheathed cable as earth continuity conductor for one 5 pin 15 Amps power socket outlet point on independent board/400 watt flood light. |
| 94 | M&L for sub main wiring using two run single core 4 Sqmm fire retardent PVC insulated and unsheathed cable with copper conductor 1100 vots grade, ISI mrked complete with PVC conduit accessories like bends tees etc and PVC insulatd copper cable 4 Sqmm for earth ire and connecting to earth dolly , complete all as specifiedvand directed. |
| 95 | M&L for sub main wiring using two run single core 2.5 Sqmm fire retardent PVC insulated and unsheathed cable with copper conductor 1100 vots grade, ISI mrked complete with PVC conduit accessories like bends tees etc and PVC insulatd copper cable 2.5 Sqmm for earth ire and connecting to earth dolly , complete all as specifiedvand directed. |
| 96 | S&F switch 1 way 6A, 1 module complete all as specified and directed. |
| 97 | S&F switch 1 way 16A, 1 module complete all as specified and directed. |
| 98 | S&F Bell push 6A 1 module complete all as specified and directed. |
| 99 | S&F switch 2 way 6A,1 module complete all as specified and directed. |
| 100 | S/F 6A - 2/3 pin combined 2 module complete all as specified and directed. |
| 101 | S/F Socket 6A/16A - 2/3 pin combined 2 module complete all as specified and directed. |
| 102 | S/F ceiling rose surface bakelite three terminal three terminal 250/230 volts ISI marked complete all as specified and directed. |
| 103 | S&F Fan step regulator, 120W - 2 module complete all as specified and directed. |
| 104 | S&F bell ding dong type A/C 240 V complate all as specified and as directed. |
| 105 | S/F in DB's Sheet metal double door enclosure for SPN DB 4 way type 240 volts and 200 Amp ratings bus bar complete all as specified and directed. |
| 106 | Supply and fixing amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and directed. |
| 107 | (a). MCB SP up to 32 Amp, 240 volts |
| 108 | (b). MCB SPN upto 63 Amp, 240 volts |
| 109 | Supply and fixing LED Tubelight fitting ENERGY Efficient 20 Watt 2000 lumen bright light complete all as directed by Engr-in-charge |
| 110 | Supply and fixing LED Tubelight fitting ENERGY Efficient 10 Watt 2000 lumen bright light complete all as directed by Engr-in-charge |
| 111 | S&F BLDC Ceiling fan 1200 mm sweep single phase 230 V with blaade complete all as specified and directed. |
| 112 | S&F Exhaust fan steel body AC single phase 230 V of size 300 mm sweep with blade & frame complete all as specified and directed. |
| 113 | S&F Exhaust fan louvers for 300 mm sweep inreplacement complete all as specified and directed. |
| 114 | M& L for making hole for exhaust for 300 mm dia in existing wall and making good the damage surface all as directed ccomplete. |
| 115 | M & L for earthing complete with galvanised steel earth plate electrode 600 x 600 x 6.0 mm thick burried directly in ground earth pit not less than 2.25 mtr deep below ground level connected to & including galvanised earth lead wire 4 mm dia by means of nuts and bolt check nuts and washers of galvanised rion sheet all as shown in electrical plate Nos 5 of SSR Part - I and connected to earthing test point complete including testing filling of adquate quantity of charcoal dust and common salt including refilling earth and removal of surplus soil upto 50 mtrs PCC 1:3:6 type CI chamber precast RCC cover 40 mm thick reinforced with 6 mm dia MS bar 3 Nos both way with handle made out of 6 mm dia MS bar water pipe with wire mesh and connecting testing etc complete all as specified and directed. |
| 116 | Supply and fixing LED security light luminaire 35 Watt freedom , pressure die cast aluminum housing, heat resistant glass, IP65 protection, better optics for uniform distribtion complete with all accessories internally pre wired and including connecting up with three core 1.5 sqmm flexible copper conductor cable from ceiling rose to connector of light complete all as specified and directed. |
| 117 | Following items shall be executed under the job\\"PROVN OF GREASE TRAP FOR AIRMEN MESS AT AFS DEESA\\" |
| 118 | Demolition of Brickwork or stone/boulder masonry, built in cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles. |
| 119 | M&L Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in CM 1:6 all as specified and as directed. |
| 120 | Demolition of reinforce Cement Concrete of any description and in any pisition complete all as specified and as directed |
| 121 | Taking Down cement plaster any description on brick or stone wall/ceiling including raking out joint, haking for key scrubbing with water etc |
| 122 | M&L rendering 15mm thick cement plaster on fair faces of concrete surfaces in CM 1:4. |
| 123 | M&L cement concrete Type B1 1:2:4 (20mm graded aggregate) as in copping all as directed. |
| 124 | Dismantling of 100mm dia cast iron drain pipes, jointed in cement mortar and taking out of trenches, if required all as directed |
| 125 | M&L 100mm did Cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, laid in (spun pipe) trenches or in floors/wall all as directed. |
| 126 | S & F 1.5mm thick stainless steel (grade of steel 304) grease trap of durability, corrision resistance, an longevity with inclusive internal baffles walls for guide the flow of water with some traps include a basket to collect solid food waste, preventing it from entering the trap for a easy access and for cleaning and maintenance. size of grease trap 1.95m x 1.15m x 0.95m (LxBxH). complete all as specified and directed. |
| 127 | Note for all items :- If any item gets repeated in this schedule, the lowest rate quoted for those same items by the L-1 bidder shall be considered for payment and decision of Accepting Officer i.e. GE(AF) Baroda in this regard shall be final and binding. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 08, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 22, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 10 daysAug 24, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 12 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender