Tender For special Repair To Boundary Wall And War Memorial Near Bldg No P-194 At Si Line Under Ge Bhopal
Tender Value
48 Lakhs
Estimated cost
Bid Submission
29 Aug 2026
6 days left
EMD
96000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Bhopal → Madhya Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repair To Boundary Wall And War Memorial Near Bldg No P-194 At Si Line Under Ge Bhopal
BOQ
| Sl. No. | Item Description |
| 1 | Note :(i) Please refer Sch A/ BOQ Notes before quoting the tender for all phases/ items mentioned below.(ii) Amount of Schedule of credit shall be deducted offline |
| 2 | Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed. |
| 3 | Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed. |
| 4 | M&L for PCC (1:4:8) type D-2 using 40 mm graded stone aggregate as in foundation filling & mass concrete complete all as specified and directed. |
| 5 | M&L for 25mm thick in PCC 1:2:4 type B0 using (using 12.5mm gradded stone aggregate) as in bedding layer for laying in floor as in levelling course complete all as specified and directed. |
| 6 | M&L for reinforced cement concrete (design mix) M-25 (using 20 mm graded stone aggregate) Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed. |
| 7 | M&L for reinforced cement concrete (design mix) M-25 (using 20 mm graded stone aggregate) Columns, pillars, piers, posts and struts etc complete all as specified and directed. |
| 8 | M&L for reinforced cement concrete (design mix) M-25 (using 20 mm graded stone aggregate) Beams, bands, cantilevers, bressummers, lintels over 1.5m span etc complete all as specified and directed. |
| 9 | Use&waste for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter surface flat with fair finished surfaces complete all as specified and directed. |
| 10 | Use&waste for Formwork sides of pillars, posts, struts, piers, columns and stanchions.; vertical or to batter surface flat and fair finished surfaces complete all as specified and directed. |
| 11 | Use&waste for Formwork to Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc..; vertical or to batter surface flat and fair finished surfaces complete all as specified and directed. |
| 12 | M&L mild steel TMT reinforcement bars 10mm and over, using cut to length, bent to shape as required including cranking bending spirally for hooking ends and binding with and including mild steel wire (annealed not less than 0.9mm dia or securig with clips etc complete all as specified and directed. |
| 13 | All as per ser item no 11.00 here-in-before but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders round bars complete all as specified and directed. |
| 14 | M&L for modular size brickwork with fly ash bricks straight or curved on plan exc 6 m mean radius built in cement mortar 1:4 complete all as specified and directed |
| 15 | M&L rendering 15 mm thick on fair face of brick work or concrete surfaces or brick masonry surfaces or surface in CM 1:4 finished even and smooth without using extra cement complete all as specified and directed. |
| 16 | M&L rendering 15 mm thick on fair face of brick work or concrete surfaces or brick masonry surfaces or surface in CM 1:4 finished even and rough complete all as specified and directed. |
| 17 | M&L for preparation of newly plastered or unplastered surfaces in walls soffits, facia, chajjas and applying two coat of exterior weather proof water based emulsion over a coat of compatible primer complete all as specified and directed. Make:Asian paints apex ultima/berger weather coat long life 7/Nerolic Excel total |
| 18 | S&F Providing and laying 80mm thick rubber moulded factory made chamfered edge cement concrete glossy finish paver block of M-40 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, laid in required colour & pattern over and including 50 mm thick compacted bed of fine river sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer and filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed |
| 19 | M&L Providing, cement concrete 1:2:4 type B1 using 20mm gradded stone aggregate as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands,plinth courses, string courses,lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed including neccessary formwork complete all as specified and directed |
| 20 | Surface Excavation n exc 30 cm deep averaging 15cm deep and getting out in hard dense soil complete all as specified and directed |
| 21 | Excavating in trenches n exc 1.5m wide and not exc 1.5m in depth for foundation and getting out in hard dense soil complete all as specified and directed. |
| 22 | Returning, filing in, excavated soil including spreading, levelling, watering and well ramming in layers not exceeding 25cm etc complete all as specified and directed. |
| 23 | Removing surplus excavated soil nexc 50 mtr and depositing where directed at a level n-exc 1.5 mtr above the starting point complete all as specified and directed. |
| 24 | M&L for 18-20mm thick granite (of approved color and shade) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking plat forms, riser and like in fixed with stone tile adhesive including pointing in white cement (1:2) using marble dust with admi ture of pigment to match with shade of granite complete all as specified and directed. |
| 25 | M&L for Granite (of any type) tiles 18-20mm thick machine cut, laid bedded over tile adhesive and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and directed. |
| 26 | M&l for Makrana White Marble work (table rubbed and polished) for wall lining (veneering to wall) 18-20mm thick fixed with approved tile adhesive and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade complete all as specified and directed. |
| 27 | M&L Providing edge moulding to marble stone any desc 18-20mm thick stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc.complete all as specified and directed. |
| 28 | M&L for rounding to edges of granite stone slabs one edge, such as in steps, cooking platform and other similar situations complete all as specified and as directed by Engr-in-Charge |
| 29 | M&L Providing and fixing machine cut/ cnc carved marble jali panel of approved Makrana/ italian marble, 25 mm thick of approved design and pattern including all carving and cutting, edge finishing, polishing necessary grooves, dowels, SS cramps / pins fixed with epoxy adhesive in position as directed by the Engr-in-Charge |
| 30 | M&L for full body vitrified tile 9-10 mm thick of size n. exc 1.00 sqm each fixed with approved tile adhesive and 5mm spacer, joint filled with tile grout (epoxy) of any colour including all as directed by the Engr-in-Charge |
| 31 | M&L for Engraving, carving and highlighting of inscriptions, names, letters, numerals, logos and approved designs on existing polished black granite stone of any thickness of size (25-30) mm x (18-20) mm by computerized/CNC engraving or sand blasting process, including filling the engraved portion with weather-resistant white/golden enamel paint, polishing, cleaning the surface and making good complete as directed by the Engineer-in-Charge. |
| 32 | S&F of traditional marble canopy with kalash top made from marble of thickness 20-25mm including all moulding ,cuttting and size as per drawing complete all as specified and directed |
| 33 | M&L for concealed point wiring for one light/one fan/one exhaust fan controlled by one switch complete with and includidng single core PVC insulated unsheathed FRLS copper conductor 1.5 sqmm cable as per IS 694:2010 ISI marked annealed multistranded copper conductor drawn through and including medium grade PVC conduit as per IS 9537 (Part-III): 1983 of suitable nominal size as required at site dia but not less than 20mm noninal size including modular / non modular type all accessories/fitting / metal flush box / cover plate/junctiion boxes/ inspection cover etc ISI marked and sunk terminal boxes flush galvanised metal boxes with addtional single core PVC insulated unsheathed FRLS copper conductor 1.5 sqmm multi-strands cable as continious earth wire connected to metalic body at one end and common earth dolly to other end including cost of cutting chase and making good to distrubed surfaces of wall with cement mortor 1: 3 including necessary plaster and poiinting in cement mortor 1:3 with white wash / distemper/ other painting complete all as specifiecd and as directed Note:- cost of cutting chase and making good shall be included in the quated rates. |
| 34 | All as per Srl item No 32.00 here-in-before but for socket outlet 5/6 amp on independent board complete all as specified and directed by Engineer - in - Charge. |
| 35 | All as per Srl item No 32.00 here-in-before but for one three pin socket outlet 5 Amp on same board with other switches complete all as specified and directed by Engineer - in - Charge. |
| 36 | All as per Srl item No 32.00 here-in-before but for one socket outlet 6 pin 5/ 15 Amps on independent board with wire of size 2.5 Sqmm complete all as specified and directed by Engineer - in - Charge. |
| 37 | All as per Srl item No 32.00 here-in-before but for socket outlet 6 pin 5/ 15 Amps on independent board with wire of size 4.0 Sqmm complete all as specified and directed by Engineer - in - Charge. |
| 38 | S & F modular switch one way 6 Amp one module, 240 volts complete all as specified and directed by Engineer - in - Charge |
| 39 | Supply and fixing modular socket outlet 2-in-1, 2/3 pin, 6 Amps, 240 volts, controlled by one switch complete all as specified and directed by Engineer - in - Charge |
| 40 | S&F modular switch one way 16 Amp one module, 240 volts complete all as specified and directed by Engineer - in - Charge |
| 41 | Supply and fixing modular socket outlet 2-in-1, 2/3 pin, 6/16 Amps, 240 volts, controlled by one switch complete all as specified and directed by Engineer - in - Charge |
| 42 | S&F of PVC insulated PVC sheathed, flexible circular cable 3 core, 2.5 Sqmm multi strandrands copper conductor AC, 230 V complete all as specified and directed. |
| 43 | S&F non metalic heavy grade PVC conduit ISI marked of size 20mm dia incl all accessories complete all as specified and directed. Make Plasto/ Palza/ Polycabor equivalent. |
| 44 | S & F in replacement sheet metal enclosure double door, type surface mounted concealed in wall 12 ways, 240 Volts, ISI marked 200 amps bus bar dust and vermin proof suitable for incorporation MCBs and isolators etc complete all as specified and directed by Engineer - in - Charge. |
| 45 | S&F in replacement MCB SP suitable for 240 volts, AC supply 6 to 32 Amps , with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed by Engineer - in - Charge. |
| 46 | S&F in replacement MCB SPN suitable for 240 volts, AC supply 40 to 63 Amps, with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed by Engineer - in - Charge. |
| 47 | M&L for sub main wiring with approved colour coding as per IS with single core PVC insulated FRLS cable 1100V unsheathed 3 wires, (2 for phase and neutral and one for earth) with stranded copper conductor of 6.0 sqmm nominal cross section area,and drawing into 20mm external diameter rigid non metallic PVC conduit, ISI marked, medium grade, inclusive of all fittings such as tees, bends, junction boxes, elbows, saddles, pipe hooks, couples, lock outs, etc. in concealed wiring system by cutting of walls (brick or stone) and making good disturbed surface of wall in CM 1:3 complete all as specified and directed. Note : (i)Wiring to be done as per approved colour code in IE rule. (ii) Two runs of 6.0 sqmm cable for phase and neutral ansd one run of 6.0 sqmm cable of earth continuity conductor & PVC conduit pipe shall be measured as one unit length. |
| 48 | M&L for sub main wiring with approved colour coding as per IS with single core PVC insulated FRLS cable 1100V unsheathed 3 wires, (2 for phase and neutral and one for earth) with stranded copper conductor of 4.0 sqmm nominal cross section area,and drawing into 20mm external diameter rigid non metallic PVC conduit, ISI marked, medium grade, inclusive of all fittings such as tees, bends, junction boxes, elbows, saddles, pipe hooks, couples, lock outs, etc. in concealed wiring system by cutting of walls (brick or stone) and making good disturbed surface of wall in CM 1:3 complete all as specified and directed. Note : (i) Wiring to be done as per approved colour code in IE rule. (ii) Two runs of 4.0 sqmm cable for phase and neutral ansd one run of 4.0 sqmm cable of earth continuity conductor & PVC conduit pipe shall be measured as one unit length. |
| 49 | M&L for sub main wiring (Three phase) with approved colour coding as per IS with single core FRLS PVC insulated, unsheathed, mutistranded copper conductor cable of size 4.0 sqmm 6 wires (three for phase one for neutral and two for earth) drawn into 25 mm external diameter rigid non metallic PVC conduit, ISI marked, medium grade with its accessories, inclusive of all fittings such as tees, bends, junction boxes, elbows, saddles, pipe hooks, couples etc. in concealed wiring system by cutting of walls (brick or stone) and making good disturbed surface of wall in CM 1:3 and complete all as specified and directed. Note : (i)Wiring to be done as per approved colour code in IE rule. (ii) Four runs of 4.0 sqmm cable for phase and neutral, two runs of 4.0 sqmm cable of earth continuity conductor & PVC conduit pipe shall be measured as one unit length. |
| 50 | Supply & fixing decorative wall light, gold finish fixture with white glass diffuser Brown Metal Wall Light colour- Metal (Black Antique) Glass (White) Cap Type: suitable for E27 Holder to fit LED bulb & Maximum Wattage Support : Upto 40W- Voltage : 220V.design:- Versatile & Stylish design with modern fittings & Metal frame. incl 9 W warm LED bulb suitable for Guarden light. complete all as specified and directed by Engineer in charge. |
| 51 | Supply and fixing of 6W warm white decorative wall led lighgt 2 way K type light & Input Voltage: Typically 160V-280V AC, suitable for standard household voltage. Light Source: SMD LED or Epistar LED chips.Color Temperature: 3000K (Warm White) is standard for cozy, non-glare illumination.Luminous IP Rating (Waterproofing): IP65, indicating dust-tight and protection against water jets (suitable for indoor/outdoor use) Die-cast aluminum body (powder-coated, anti-corrosion) with a polycarbonate diffuser. Lifespan: Often up to 50,000 burning hours all as specified and directed. |
| 52 | Supply & fix surface mounted LED bush light pressure die-cast aluminium heat sink & clear PC as a cover in white powder coated finish with Independent electronic LED driver. mounting spot focus LED light round warm in colour with excellent thermally managed luminaire 9 watt , 220V AC withtoughned glass IP66, diffuser soft glare free light suitable for garden illumination including connecting up with driver three core flexible coppder conductor cases of suitable size complete all as specified and directed by Engineer in charge.Make: Hellonix Cat part No -HLOBUL-27-09-CW or equivqlent make Bajaj/Havells / C&G/ Philips as approved by GE. |
| 53 | S&F in replacement building security light fitting complete with 36 watt LED type pressure die cast aluminium housing and heat resistant IK-64 with frame protection and better optics for uniform distribution complete fixed bracket made out of GI pipe 32 mm dia (light grade) 1.5 metre long and MS clamp and nut bolts washers and connected with twin core cable 1.5 sqmm from ceiling rose to fittings connector all as specified and directed |
| 54 | Supply and fixing of 3W warm decorative LED foot step light & Input Voltage: Typically 160V-240V AC, suitable for standard household voltage. Light Source: SMD LED or Epistar LED chips, Color Temperature: 3000K (Warm White) is standard for cozy, non-glare illumination.Luminous Flux: Approximately 100 lumens for a 3W model. IP Rating (Waterproofing): Generally IP65, indicating dust-tight and protection against water jets (suitable for indoor/outdoor use), Material: Die-cast aluminum body (powder-coated, anti-corrosion) with a polycarbonate diffuser, Lifespan: Often up to 50,000 burning hours.Dimensions: Common sizes include compact 45 x 84 x 84 mm, 8x8x4 cm, or 94x70x40 mm, Mounting: Recessed (with a plastic mounting box) or surface-mounted all as specified and directed. Cat part No -HLOSTL-27-03-CW of Hellonix or equivqlent Bajaj/Haveels / C&G/ Philips as approved by GE. |
| 55 | Supply and fixing of 3W warm decorative LED ground burial round light & Input Voltage: Typically 160V-240V AC, suitable for standard household voltage. Light Source: SMD LED or Epistar LED chips, Color Temperature: 3000K (Warm White) is standard for cozy, non-glare illumination.Luminous Flux: Approximately 100 lumens for a 3W model. IP Rating (Waterproofing): Generally IP66 indicating dust-tight and protection against water jets with toughened class (suitable for indoor/outdoor use) Material: Die-cast aluminum body (powder-coated, anti-corrosion) with a polycarbonate diffuser, Lifespan: Often up to 50,000 burning hours.Dimensions: Common sizes include compact 45 x 84 x 84 mm, 8x8x4 cm, or 94x70x40 mm.Mounting: Recessed (with a plastic mounting box) or surface-mounted all as specified and directed.Make: Hellonix Cat part No -HLOGB-27-03-CW or equivqlent make Bajaj/Havells / C&G/ Philips as approved by GE. |
| 56 | S&F of flexible LED strip uses high brightness SMD LED as the light source for indoor application, luminaire 24 watt, 220 Volts AC with high efficiency light complete with driver, holder and LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. Cat part No - LHEHDLPFUN1W024 (Flexion Neo Led Strip 24 W of any colour) of Havells or equivqlent make Bajaj/ C&G/ Philips as approved by GE. |
| 57 | M&L for earthing complete with galvanised steel earth plate electrode size 600X600X6mm thick burried directly in ground vertically to a depth not less than 2.25m deep below normal ground level with top edge of earth plate not less than 1.5m deep below normal ground level and connected to and including GI earth lead wire 4mm dia by means of bolts, nuts, check nuts & washers of galvanised iron and connected to test point all as shown in electrical plate No 3 of SSR part I-2009 and all as specified or indicated and testing on completion including excavation and earth work in any type of strata available at site, PCC (1:3:6) type C-1 earthing chamber, pre cast RCC slab 50 mm thick in cement concrete (1:2:4) type B-1 using 20 mm graded crushed stone aggregate reinforced with welded steel wire fabric (XPM) weight not less than 4 kg/sqm funnel with GI watering pipe of 20 mm bore medium grade, wire mesh and lugs, GI protection pipe of 15 mm bore light grade up to 7.5 metre long all as specified and directed. NOTE :- GI earth wire and protection pipe beyond 7.5 metre will be measured and paid separately. |
| 58 | Excavation in trenches n. exc. 1.5 mtr in wide and n. exc. 1.5 mtr in depth for laying of underground cable and getting out in hard/dense soil complete all as specified and directed. |
| 59 | Returning, filling in excavated soil in trenches including spreading, leveling, watering and well ramming in layers n. exc. 25 cm thick complete all as specified and directed |
| 60 | Removing of excavted soil to a distance n. exc. 50 mtr and deposited where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed. |
| 61 | M&L local sand dry, filling in trenches around under ground cable complete all as specified and directed. |
| 62 | M&L for providing of un-reinforced precast concrete cable cover class LV, Type 1 size 250mmx 150mm x 40mm laid flat dry for protection of under ground cable complete all as specified and directed.class,, flat, |
| 63 | Excavation in trenches n. exc. 1.5 mtr in wide and n. exc. 1.5 mtr in depth for laying of underground cable pipe and getting out in soft disintegrated rock all as specified and directed. |
| 64 | M&L for making good the disturbed surface by filling PCC 1:2:4 type B-1 using 20 mm graded course aggregate to match with existing surfaces all as specified and directed. |
| 65 | Supply, fix, testing & commissioning for outdoor Bus bar box size 650 x 650 x 400 mm fabricated out of 3.15 mm thick MS Sheet having 4 Nos closed Aluminium bus bar chamber of capacity 200 A (including necessary insulator) suitable for 3 phase & neutral, 4 wire 50 Hz AC,415V with minimum eight out going and adjustable thermal & adjustable magnetic 36KA 100 amp MCCB FP Ics= Icu 75 % at 415 volt as incomining system, 63 Amps TPN MCB (3 nos) including red,blue & yellow LED indication lamp and both side openable hinged cover with proper locking arrangement ,outdoor type weather proof with angle iron of size 50x50x5 mm(including painting of angle iron) outoor, floor mounting 100 cm above ground level grouting including making PCC 1:2:4 type B-1 using 20 mm graded course aggregate with complete plastering & white wash etc also includes provision of suitable size of cable glands,cable lugs,nut, bolts,washers etc for fixing of cable with the bus bar.The bottom portion of enclosure shall be minimum 90 cm above ground level with legs of angle iron size 25X25X3 mm complete all as specified and directed. |
| 66 | Supply, laying & testing of cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminum conductor of size 25 sqmm 4 core all as specified & directed. Note:- Excavation & earth work and pipe / sand / bricks for cable protection shall be measured and paid for separately under appropriate item of this schedule) |
| 67 | M & L GI Tubing \\"light grade\\" galvanized for protection LT Cable all as specified of size 40 mm bore complete all as specified and directed by Engr-in-Charge. |
| 68 | Supply and fix GI tubing ,medium grade, of size 25 mm dia ISI Mark galvanised laid in floors/walls including fittings such as bends elbows reducers and complete accessories complete all as specified and directed. |
| 69 | Supply and fixing Gun metal gate valve/glove valve ISI marked with Iron wheel head screwed both end for GI tubing of size 25mm dia complete all as specified and directed. |
| 70 | Deduct Schedule of credit (calculation will be done off line) Rs. 4250.00 Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 08, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 29, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 6 daysAug 31, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 8 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender