Tender For Installation Of Closed Combustion Cremation Furnace (Cccf) Town And Junction Shamshan Bhumi
Tender Value
19.38 Lakhs
Estimated cost
Bid Submission
17 Aug 2026
2 days left
EMD
38760
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Hanumangarh → Rajasthan
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Installation Of Closed Combustion Cremation Furnace (Cccf) Town And Junction Shamshan Bhumi
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in excavation in foundation, trenches etc. including dressing of sides and ramming of bottoms, including getting out the excavated material, refilling after laying pipe/ foundation and disposal of surplus excavated material at a lead upto 50m suitable site as per direction of Engineer for following depths, below natural ground / Road top level.In all types soils/ saturated soil such as moorum, sand, sandy silt,clay, black cotton soil, kankar, etc. Depth upto 1.5 m |
| 2 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level :1:4:8 (1 Cement : 4 fine/ coarse sand : 8 graded stone aggregate 40 mm nominal size). |
| 3 | Brick work with FPS bricks of class designation 75 in foundation and plinth in:Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 4 | Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In stringers, treads, landings etc. of stair cases including use of chequered plate wherever required, all complete |
| 5 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level : 1:1½:3 (1 Cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size). |
| 6 | Providing and fixing of 60mm thick precast cement concrete interlocking paver block casted with rubber moulds in approved reflective colour and design having minimum compressive strength of 300 kg/ sq cm. The CC paving blocks be laid on average 50mm thick bed of coarse sand and the joint is to be filled with fine sand. Laying procedure on compacted sub-base as defined. Complete job is to be executed as per the instruction of Engineer in-charge. The rates to be inclusive of all lead & Lifts etc. complete as per specifications. |
| 7 | Providing corrugated G.S. sheet roofing including vertical/ curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead and including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete upto any pitch in horizontal/ vertical or curved surfaces) excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.63 mm thick with zinc coating not less than 275gm/m² |
| 8 | SITC of Antyeshti Yantra with following specification :-1.(A) Body MS. Sheet size 3mm & 2 mm angle structure 50x50x5mm MS(B) Lining fire brick alumina 30% with ceramics board thickness 50 mm capacity 1260 C(C) White heat castable (k) & accost (50) for fire bricks feting(D) Angle 65x65x10 & 35x5 SS 304 grade(E) Road 30 mm 370 mm SS 304 Grade(F) Pipe OD 40 mm thickness 5 mm SS 304 grade(G) Ceramics blanket (64D) total bolts & nut MS & SS(H) Thermostat size 20 mm OD x 450 mm length(I) Control panel auto and manual both with change over /2-way switch(J) Blower complete with fan size 305 mm with 1 HP Motor Nos 2(K) Chimni length 3-meter size 350x350 mm tapper sheet thickness 3 mm With ceramic board lining(L) Ceramics board fitting 50 mm and 25 mm(M) Both side MS Door with lock size -600x550 mm thickness 5 mm MS 50 mm ceramic board and ceramic blanket(N) Sliding Trolly alignment bed angle size 50x50 mm+35x35mm+strip, length 4.5 meter(O) Sliding Trolly cover 1750x1180x400 mm sheet size 3 mm with bearing roller(P) Sliding Asthiya & Ash collecting trey Size 2200x350x100mm sheet thickness 3mm with roller SS 304 grade(Q) Coated with heat resistance paint with capacity of 600-degree silver color(R) Two step fabricated checker plate and angle size 6'x2'x1' qty 2 including loading, unloading and Transportation ele. |
| 9 | SITC of Inverter with batteries with - O/P Voltage - 220 V, O/P Current 12 amp AC Nominal, I/P current 12 amp AC max, O/P power -2 KVA, power factor-0.8, frequency-50 Hz including 12 V 150 Ah Battery Rack and battery bank comprising SMF/VRLA batteries, inter-connection wiring etc. as required complete in all respect. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 07, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 17, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 2 daysAug 18, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 3 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender