Tender For Repair /Maint Of B/R Works Of Water Supply Installation Under Ge (U) Bathinda At Bathinda Mil Stn
Tender Value
49.90 Lakhs
Estimated cost
Bid Submission
31 Aug 2026
20 days left
EMD
99800
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Bathinda → Punjab
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair /Maint Of B/R Works Of Water Supply Installation Under Ge (U) Bathinda At Bathinda Mil Stn
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and directed |
| 2 | M&L for Brick work with subclass ‘B’ old size fly ash bricks, straight or curved on plan exc 6m mean radius built in cement mortar (1:6) complete all as specified and directed by Engineer-in-Charge. |
| 3 | Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided complete all as specified and directed by Engineer-in-Charge. |
| 4 | M&L for Reinforced cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies deck slabs, and in shelves and the like complete all as specified and directed by Engineer-in-Charge. |
| 5 | Use & waste of Form work to soffits of suspended slabs such as roof slabs, floor slabs, landing horizontal or slopping similar work not. Exc 200mm thick and flat rough finished surfaces complete all as specified and directed by Engineer-in-Charge |
| 6 | Mild steel TMT bars 10 mm dia and over cut to length, bent to shapes required, including cranking, bending spirally for coping for columns, hooking ends and binding or welding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge |
| 7 | Hacking out old broken glass (any thickness, size, quality or description) from metal frames including punching or drilling out old glazing pins/spring clips and providing and fixing 3 mm thick ordinary sheet glass and glazing with oil putty not exc. 0.50 sqm in each pane complete all as specified and as directed by Engineer-in-Charge. |
| 8 | S&F in repair galvanized mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanized wire staples complete all as specified and directed by Engineer-in-Charge |
| 9 | Taking down Chowkats or frames with shutters (without taking off shutters from the frame) not exc 1.5sqm each and removing from site complete all as specified and directed by Engineer-in-Charge. |
| 10 | S&F solid PVC door frame of size 50mm x 47mm made out 5mm thick PVC sheet prelaminated on single side and plain on other side reinforced with MS square tube including painting of edges to match with prelaminated sheet, fixed in opening as per specification stipulated in SSR Part-I (2009) complete all as directed by Engineer-in-Charge |
| 11 | S&F factory made or fabricated by their authorized fabricator solid paneled PVC door shutter 30mm thick (Style) consisting of frame made out MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain cover PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for style and plain PVC sheet plain colour PVC sheet 5mm thick for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail paneling of both side plain colour PVC sheet to be fitted on the MS frame welded/sealed to the stiles, rails with suitable PVC sheet beading and jointed together with solvent cement, stiles and rails feathered at edges including fixing in the frame at site as per specification stipulated in SSR Part-I (2009) complete all as directed |
| 12 | S&F in repair 100mm long aluminum anodised, barrel tower bolts extruded section complete all as specified and directed by Engineer-in-Charge |
| 13 | S&F in repair 100mm butt hinges extruded aluminium alloy with galvanized mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed by Engineer-in-Charge. |
| 14 | S&F in repair 100 mm Aluminium handles, cast type, anodised complete all as specified and directed by Engr-In-Charge. |
| 15 | S&F in repairs Vitreous china wash hand basin white flat black of size 550 x 440mm including brackets, and Bottle trap of PTMT having minimum water seal of 25mm. (Minimum weight 32mm-260gms/ 40mm-270 gms) waste fitting 40mm brass chromium plated and waste pipe and 15mm dia PVC connection with brass nuts complete all as specified and as directed |
| 16 | S & F in repair 15mm dia Pillar taps, cast copper alloy, with capstan heads, chromium lated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed by Engr-In-Charge. |
| 17 | S & F in repairs 15mm stop valve concealed type fancy type chromium plated, high pressure, with crutch or butterfly handle, screwed both ends of iron pipe or for union and fixed complete all as specified and directed by Engr-In-Charge. |
| 18 | S & F in repairs 15mm bore, fancy type, chromium plated, angle valve, cast copper alloy, screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe complete all as specified and directed by Engr-In-Charge. |
| 19 | S & F in repair 15mm bore medium grade tube galvanised with all fittings and fixed complete concealed including groove cutting for concealing to walls & ceiling or laid in floor complete all as specified and directed by Engr-In-Charge. |
| 20 | S & F in repair 20mm bore medium grade tube galvanised with all fittings and fixed complete concealed including groove cutting for concealing to walls & ceiling or laid in floor complete all as specified and directed by Engr-In-Charge. |
| 21 | S & F in repair vitreous china squatting pan Orrisa pattern size 580mm x 440mm white with integral foot rest (excluding flushing cistern and flush pipe etc) with CI ‘P’ or ‘S’ trap and fixing in Cement concrete (1:2:4), 150mm thick all round and finished just below level of rim of pan to receive the floor finishing complete all as specified and directed by Engr-In-Charge. |
| 22 | Supply & fixed in repairs vitreous China Wash down water closet (Pestel pattern) EWC with s and p trap including connection to drain (or outgoing pipe) and to flush pipe including seat cover complete all as specified and directed |
| 23 | S & F in repairs PVC 10 ltrs symphonic action type flushing cistern, low level with inlet, ball valve, float and handle including brackets, flush pipe of PVC 32mm bore and connection to WC pan complete all as specified and directed |
| 24 | Supply and fixing in repairs 75mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement, complete all as specified and directed by Engineer-in-Charge. |
| 25 | S&F in repairs PVC connections 15mm size of length 450mm complete all as specified and directed |
| 26 | Supply and fixing in replacement waste pipe (LDPE) suitable for 32mm waste coupling complete all as specified and as directed by Engineer-in-Charge. |
| 27 | S&F in repair 15mm bib taps, chromium plated fancy type cast copper alloy with crutch or butterfly handle, screwed down, secrewed for iron pipe or for brass ferrule and fixed complete all as specified and directed |
| 28 | S&F in repair 500 ltr capacity ISI marked rotational moulded three layer polyethylene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I complete all as specified and directed by Engineer-in-Charge. |
| 29 | S&F in repair 500 ltr capacity ISI marked rotational moulded three layer polyethylene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I complete all as specified and directed by Engineer-in-Charge. |
| 30 | S&F 20mm float Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge. (Minimum weight 20 mm - 210 gms) |
| 31 | S & F in repairs 20mm, fancy type chromium plated bore stop valve, cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends of iron pipe or for union and fixed complete all as specified and directed by Engineer-in-Charge. |
| 32 | Taking down cement plaster/ dado, any description on brick or stone walls, ceiling etc including racking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed. |
| 33 | M&L rendering 10 mm thick in CM 1:3 on concrete surface of ceiling, finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge |
| 34 | M&L rendering 10mm thick on fair faces or other than fair faces of brick work in CM 1:6 finished even & smooth complete all as specified and directed by Engineer-in-Charge |
| 35 | M & L rendering 15mm thick on fair faces of brick work in CM 1:4 finished even & fair without using extra cement complete all as specified and directed by Engineer-in-Charge |
| 36 | M&L for applying two coats of oil bound distemper on newly plastered wall surface using Airless spray technology or roller brush complete all as specified by Engr-in-Charge.Note: - Accessories for applying distemper should be able to spray in hard to reach areas and penetration of distemper on the surface to achieve excellent application using limited manpower complete all as specified and directed. |
| 37 | M&L for applying waterproof wall care putty over prepared surface including preparation of surface (thickness vary from 1.5 to 2mm as required for desired smoothness and levelling of surfaces in two or more layers of putty) including sanding of the putty surface after drying to achieve even and smooth finish for receiving painting complete all as specified and directed. |
| 38 | M & L for applying Two or more coats of weather proof exterior acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance, of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm on newly prepared surface of brick (plastered or un-plastered) or concrete surface complete all as specified and directed.Note: 1. Allow 6-8 hrs to dry the surface for painting of subsequent coats. |
| 39 | M&L for complete removal of existing treatment on wall/roof projections including facia, cornices, etc by scrapping with mechanical sander (having mechanical vacuum mechanism) with sanding pad of appropriate grit to make surface clean, free from dust, loose paint etc by skilled labour complete all as specified and directed by Engr-in-charge. |
| 40 | M&L for applying two coats of oil bound distemper on old ceiling surface using Airless spray technology or roller brush complete all as specified by Engr-in-Charge.Note: - Accessories for applying distemper should be able to spray in hard to reach areas and penetration of distemper on the surface to achieve excellent application using limited manpower complete all as specified and directed. |
| 41 | M&L for applying two coats of oil bound distemper on old plastered wall surface using Airless spray technology or roller brush complete all as specified by Engr-in-Charge.Note: - Accessories for applying distemper should be able to spray in hard to reach areas and penetration of distemper on the surface to achieve excellent application using limited manpower complete all as specified and directed. |
| 42 | M&L for applying two coats of oil bound distemper on new plastered ceiling using Airless spray technology or roller brush complete all as specified by Engr-in-Charge.Note: - Accessories for applying distemper should be able to spray in hard to reach areas and penetration of distemper on the surface to achieve excellent application using limited manpower complete all as specified and directed. |
| 43 | S&F in repair 1.25mm lath thickness rolling shutters complete, without ball bearing, as specified including top cover, anchoring rod, hasp and staple, lock and one shop coat of primer; erected in position as indicated, complete: push pull or manual type, all as specified and directed by Engr in Charge. Please Enable Macros to View BoQ information |
| 44 | S&F in repair 1.25mm lath thickness rolling shutters complete, without ball bearing, as specified including top cover, anchoring rod, hasp and staple, lock and one shop coat of primer; erected in position as indicated, complete: push pull or manual type, all as specified and directed by Engr in Charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 07, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 31, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 20 daysSep 02, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 22 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender