Tender For Addition/Alteration To Otm Accn At Cerain Location At Nagrota Under Ge Nagrota
Tender Value
5.35 Crore
Estimated cost
Bid Submission
07 Sep 2026
22 days left
EMD
5.92 Lakhs
Bank guarantee accepted
Document Fee
3000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jammu → Jammu and Kashmir
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Addition/Alteration To Otm Accn At Cerain Location At Nagrota Under Ge Nagrota
BOQ
| Sl. No. | Item Description |
| 1 | Taking down chowkhats or frames with shutters (without taking off shutters from the frames) not exceeding 1.5sqm and removing to store, complete all as directed. |
| 2 | Taking down chowkhats or frames with shutters (without taking off shutters from frames) exceeding 1.5 sqm but not exceeding 4 sqm each and removing to store, complete all as specified and directed. |
| 3 | Demolition of brickwork or stone/boulders masonry, built in cement mortar including all quoins, arches, pillars etc, but excluding ashlar facing, dressed stonework and precast concrete articles complete all as directed. |
| 4 | Demolition of cement concrete (unreinforced) in ground floors and pavings not exceeding 15cm thickness (below or above ground level) complete all as directed. |
| 5 | Demolition of unreinforcement cement concrete of any description and in any position not otherwise specifically provided for, complete all as directed. |
| 6 | Demolition of reinforcement (reinforcement cut as required to facilitate demolition) cement concrete of any description and in any position not otherwise specifically provided live damaged surfaces irregular facia, chajjas and like on for complete all as specified and directed. |
| 7 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. |
| 8 | Taking down cement plaster on brick or stone wall etc including racking out joints, hacking for key scrubbing down with water etc; to receive new plaster etc; complete all as specified and directed. |
| 9 | Pressed steel frames of size 125mm x 60mm, made out of 1.25 PBI sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc., including one coat of primer, including filling of plain cement concrete (1:3:6) type C-0 (using 12.50mm graded crushed stone aggregate), complete all as specified and as directed . |
| 10 | Pressed steel frames of size 105mm x 60mm, made out of 1.25 PBI sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., including one coat of primer, including filling of plain cement concrete (1:3:6) type C-0 (using 12.50mm graded crushed stone aggregate), complete all as specified and as directed . |
| 11 | Solid PVC Door Frames of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed. |
| 12 | 100mm mild steel butt hinges, medium weight, cold rolled and fixed, completed all as specified and directed. |
| 13 | 75mm mild steel butt hinges, medium weight, cold rolled and fixed, completed all as specified and directed. |
| 14 | Floor doors stoppers of aluminium alloy body and tenque anodised with hard drawn steel spring fixed in floor 140mm long, fixed in repair, complete all as specified and as directed. |
| 15 | Extruded aluminium alloy handles fabricated type anodised of size 125mm long 12mm dia complete all as specified and directed. |
| 16 | 300mm long ordinary brass rat tail rod pattern springs including roller and roller plate, complete all as specified and as directed. |
| 17 | Aluminium alloy anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed 250mm long, complete all as specified and as directed . |
| 18 | 150mm long, aluminium anodised barrel tower bolt of extruded section and fixed completed all as specified and directed. |
| 19 | Box type Steel windows with double shutters (inside for wiremesh & out side for glass), incl guard bar, hinges, steel handle, tower bolt and steel peg stay complete with glazing bar dovetailed or welded including a coat of red oxide after preparation of surface before fixing complete all as shown on drawing No CEUZ/TD/1302/2009 sheet No 1/3 to 3/3 and directed. |
| 20 | Box type Steel ventilators top hung double shutters (inside for wiremesh & out side for glass), incl guard bar, hinges, steel handle, tower bolt and steel peg stay complete with glazing bar dovetailed or welded including a coat of red oxide after preparation of surface before fixing complete all as shown on drawing No CEUZ/TD/1302/2009 sheet No 1/3 to 3/3 and directed. |
| 21 | Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails, MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain PVC sheets for top rail lock rail and bottom rail on either side and as gap insert for top rail and bottom rail panelling of plain colour PVC sheetto be fitted in the MS frame welded/sealed to the styles and rails with suitablePVC sheet beading and joined together with solvent cement, suppling and fixing in the frame at site as per specification and drawings complete all as specified and directed. |
| 22 | Factory made, HDF prelaminated moulded door shutter, 35mm thick (style) with 2, 4 or 6 raised panel design with 2mm thick, 3D wood grain moulded PVC sheet on the front face and 2mm plain colour PVC sheet on back face, supplied and fixed to frame at site all as per specification and drawing No CEUZ/TD-1343/2013 sheet No 1/1 complete all as specified. |
| 23 | Factory made, single piece wire guazed panel HDF door shutter 35mm thick (style) with 2, 4 or 6 raised panel design including GI wire gauge complete supplied & fitted in the frame at site as per specification and drawing No CEUZ/TD-1343/2013 sheet No 1/1 complete all as specified. |
| 24 | Anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, door seal at bottom,anodised aluminium snap beading screws etc. (thickness of powder coating should not less than 50 micron) complete all as specified and directed. |
| 25 | Powder coated aluminium frame work (minimum thickness of powder coating 50 micron) for doors, windows, ventilators and partition, (sliding/openable/fix doors, windows, ventilator), etc with one, two or more rebates (reqd as per site), including joining cleat for fixing with dash fasteners of required dia and size, including filling up gaps at junctions, ie top, bottoms and sides etc complete all as specified and directed. |
| 26 | Powder coated aluminium work (minimum thickness of powder coating 50 micron) for window, ventilator shutters and partition wall, etc; sliding/openable/fixed (as per required at site) type without sash bar, aluminium section weighing 0.55 kg/m, including necessary locking arrangement, guide wheels, joining cleats, glazing clips rubber packing anodised aluminium snap beading screws etc; complete all as specified and directed. |
| 27 | Sheet glass plain/coloured (as approved by GE), 5.5mm thick, and glazing with rubber packing, screws or glass putty in squares exceeding 0.5 Sqm each pane complete all specified. |
| 28 | Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, complete all as specified and as directed. |
| 29 | Dismantling wall and ceiling boards (fiber, pulp, insulation; etc) or insulation boards / slabs / blankets; any thickness including cover fillets, complete all as specified and as directed. |
| 30 | 8mm thick, seamless calcium silicate ceiling made out of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25mm long self drilling and tapping screws having philips head with under head cutter at 200mm center to centre including finishing thr joints of face board with specially formullated jointing compound and 48mm wide fibre tape to provide seamless finish with 8 mm thick for seamless false ceiling fixed with screw over and including Gl frame work comprising of Gl perimeter channnel 0.55mm thick with two unequal flanges of 20mm and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre / intermediate channel 0.9 mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exceeding 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre complete as per manufacturer instruction including two coat of oil emulsion over 1mm putty, hangers 6 mmm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40mm x 3mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long complete all as specified and directed |
| 31 | Stainless steel wire cloth of 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed. |
| 32 | Sheet glass, 3.00mm thick, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane, complete all as specified and directed. |
| 33 | Figured glass, 4.00mm thick, pin head type and glazing with oil putty in square not exceeding 0.5 Sqm in each pane, complete all as specified and directed. |
| 34 | Tubular curtain rail 32mm dia aluminum brass polished with ends bulbs rings of required size including brackets complete all as directed.Note: Colour as directed by Engr-in-charge. |
| 35 | Brick work with subclass \\"B\\" bricks, using old size bricks, straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6 complete all as specified and directed. |
| 36 | Brick work with subclass \\"B\\" bricks using old size bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and directed. |
| 37 | Rendering 15mm thick in cement mortar 1:6 on fair faces of brick work or concrete surfaces, finished the surface even and smooth without using extra cement, complete all as specified and directed. |
| 38 | Rendering 15mm thick in cement mortar 1:4 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement including mixing of water proofing compound as per manufacuture instructions, complete all as specified and directed. Note: (i) Qty of WPC 200ml per cement Bag or as per manufacturer instructions (ii) Integral water proofing compound shall be measured and paid for seperately as supply only. |
| 39 | Rendering 5mm thick in cement mortar 1:3 on ceiling finished even and smooth without using extra cement including three coat of white wash on ceiling including preparation of surface complete all as specified and directed. |
| 40 | Supply only liquid water proofing compound. |
| 41 | Providing 10mm thick cement plaster in cement mortar 1:4 on parapets over roof and finished surface even and smooth without using extra cement including taking down old plaster complete all as specified and directed. |
| 42 | Roughening surfaces of old concrete surfaces of any description over damaged surfaces irregular fascia, chajjas and in similar work and also for narrow width etc and rendering dubbing coat 15mm thick cement plaster in CM (1:4) over a coat of cement slurry @ 3.00 Kg/Sqm making surface even followed by 05mm thick rendering in cement mortar 1:3 finished even & smooth without using extra cement complete all as specified and directed |
| 43 | Applying two coats of synthetic enamel paint on new steel surfaces any description, not otherwise described over 10 cm width or girth complete all as specified and directed |
| 44 | Applying two coat of synthetic enamel paint over a coat of pink primer on new wood or wood based surfaces, over 10cm width or girth including preparation of surfaces complete all as specified and directed at site. |
| 45 | Preparing newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of wall putty 2mm to 3mm thick on plasterd surfaces preparatory to distempering on wall surface, complete all as specified. |
| 46 | Complete removal of existing treatment applying two coats of oil bound distemper over a coat of wall putty 2mm to 3mm thick on plasterd surfaces preparatory to distempering on wall surface, complete all as specified. |
| 47 | Preparing newly plastered surfaces of walls and applying two coats of cement base paint over a coat of primer, complete all as specified. |
| 48 | Complete removal of existing treatment on wall and applying two coats of cement base paint on old surfaces, complete all as specified and directed. |
| 49 | Preparation of newly plastered or old plastered surfaces of wall and applying two coats of white wash, complete all as specified and directed. |
| 50 | Preparation of new plastered surfaces of ceiling and applying two coat of white wash, complete all as specified and directed. |
| 51 | Preparation of old plastered surfaces of ceiling and applying two coat of white wash, complete all as specified and directed. |
| 52 | Non skid joint free coloured ceramic floor tiles 7mm to 8mm thick, (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floor etc set & jointed in neat cement slurry and pointed in coloured cement to match the surface with and including 15mm thick screed bed or bedding layer in cement mortar 1:6 including roughening of existing floor surfaces, complete all as specified and directed. |
| 53 | All as per item No. 52.00 above but in Skirting/Dado complete all as specified and directed. |
| 54 | 50mm x 300mm thick coloured glazed ceramic tiles as on walls/ vertical surfaces over 15mm cement rendering in cement mortar 1:4, including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing ), removing serviceable tile to store and rubbish off the premises, complete all as specified and directed. |
| 55 | Vitrified Ceramic tiles 10 mm thick Light shade (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over and including 15 mm thick screed bed in cement and sand mortar 1:4, complete all as specified. |
| 56 | All as per item No 54.00 above but in Skirting/Dado complete all as specified. |
| 57 | Machine cut kota stone flooring 18mm to 20mm thick of any colour laid and jointed with grey cement slurry mixed with pigment to match the shade of the stone including grinding and polishing ( mirror finish) (Each stone not less than 55 cms x 55 cms) over 15mm thick screed bed in cement mortar 1:4 as in floor finished rough including roughening of existing surfaces by pick axicess and applying a coat of cement slurry @ 03 Kg/Sqm of surface, complete all as specified. |
| 58 | Machine cut kota stone slab 18mm to 20mm thick in skirting, dado and pillar laid and riser of stair case size (0.90-1.00 x 18-25cm) jointed with grey cement slurry mixed with pigment to match the shade of the stone including grinding and polishing ( mirror finish) over 15mm thick rendering in cement mortar 1:4 including taking out of existing dado complete all as specified. |
| 59 | All as per item No 56.00 above but in tread of stair case |
| 60 | 20mm thick, marble tiles machine cut in makrana white marble laid over cement screed and jointed with grey cement slurry including cutting and polishing of type, complete all as specified and directed. |
| 61 | 40mm thick, PCC (1:2:4) type B1 using 20mm graded crushed stone aggregate as in flooring finished even and smooth using extra cement complete all as specified and directed. |
| 62 | 25mm thick PCC 1:2:4 type B-1 using 20mm graded crushed stone aggregate as a sub base to receive topping layer finished even and rough complete all as specified and directed. |
| 63 | Plain cement concrete, 1:3:6, type C-2 (using 40mm graded crushed stone aggregate) as in plinth protection (75mm thick) finished even and fair complete all as specified and as directed. |
| 64 | Plain cement concrete 1:2:4 type B-1, using 20mm graded crushed stone aggregate, as in surface channel and drain, including form work, complete all as specified and directed. |
| 65 | Extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement including forms, moulds, mitred/stopped ends etc., complete all as specified and as directed. |
| 66 | Plain Cement concrete 1:5:10 type E-2 (using 40mm graded crushed stone aggregate) as in any situation, complete all as specified and directed. |
| 67 | RCC 1:2:4, type B1 (using 20mm graded crushed stone aggregate) as in chajja etc, complete all as specified and directed. |
| 68 | Form work to chajjas troughs and similar items including edges complete all as specified and directed. |
| 69 | Formwork on rough finished surfaces to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs not exceeding 20cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exceeding 5cm but not exceeding 10cm wide complete all as specified. |
| 70 | MS TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed. |
| 71 | Mild steel, TMT bars 6mm to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed. |
| 72 | Mild steel framed work such as grills, gratings. etc. with ends of bars shouldered and or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railing , framedwork or water tanks and similar work conforming to Fe 290, Gde-E-165, complete all as specified and directed. |
| 73 | Rotational moulded polyethylene water storage tanks of 500 Litres capacity (ISI marked), (cylindrical vertical tanks with closed top) (White in Colour and three layered) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc; complete all as specified and directed. |
| 74 | Rotational moulded polyethylene water storage tanks of 1000 Litres capacity (ISI marked), (cylindrical vertical tanks with closed top) (White in Colour and three layered) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc; complete all as specified and directed. |
| 75 | Taking up or down steel tubing and connections including cleaning for refixing or removal to store for following bore of pipe complete all as specified and as directed. |
| 76 | 15mm bore |
| 77 | 20mm bore Please Enable Macros to View BoQ information |
| 78 | 20mm bore Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 07, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 07, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 22 daysSep 09, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 24 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender