Tender For Special Repairs To Bldg No P-362 At Umed Vihar And Provn Of Geysers At Or Mess Of 3 Cesr At Rms
Tender Value
46 Lakhs
Estimated cost
Bid Submission
27 Aug 2026
10 days left
EMD
92000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Wokha → Nagaland
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Special Repairs To Bldg No P-362 At Umed Vihar And Provn Of Geysers At Or Mess Of 3 Cesr At Rms
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling floor, hearth or wall tiling including cement mortar bedding (including backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed. |
| 2 | Demolition of cement concrete (unreinforced) in ground floors and paving n.exc. 15cm thick (below or above ground level) and removal of rubbish from the site complete all as specified and as directed. |
| 3 | Demolition of brick work or stone/boulder masonry, built in cement mortar including all quions, arches, pillers etc complete all as specified and as directed. |
| 4 | Demolition of unreinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed. |
| 5 | Taking down chowkhat or frames not exc 1.5 Sqm each (without taking off shutter from the frame) complete all as specified and as directed. |
| 6 | Taking down chowkhat or frames exc 1.5 Sqm but not exc 4 Sqm each (without taking off shutter from the frame) complete all as specified and as directed. |
| 7 | Taking down shutter of any description exceeding 1.0 Sqm nexc 2Sqm each complete all as specified and as directed. |
| 8 | S&F in repairs/replacement of 750 ltr capacity rotational moulded polythylene water storage tank double layer (cylindrical, vertical with closed top ), including 20mm dia Ball valve high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed complete all as specified and as directed by Engineer-in-Charge. (Minimum weight 20 m m - 210 gms), all specified in SSR Part-I complete all as specified and as directed by Engineer-in-Charge. |
| 9 | Use and waste for formwork to chajjas including edges for flat rough finished surfaces complete all as specified and as directed. |
| 10 | M&L for RCC (Nominal Mix) (1:1.5:3) type A-1 (using 20mm graded stone aggregates) as in chajjas complete all as specified and as directed. |
| 11 | M&L for mild steel TMT bars 10mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed. |
| 12 | M&L for mild steel TMT bars 5mm dia and over upto and including 10mm dia as in stirrups, spacers and binders ,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed. |
| 13 | M&L for Cement Concrete type E-2,(1:5:10) (using 40 mm graded stone aggregate) as in foundation and mass concrete/sunken floors complete all as specified and as directed. |
| 14 | M & L for PCC 25 mm thick type B-0, (1:2:4) (using 12.5 mm graded stone aggregate) as in levelling course of floor complete all as specified and as directed. |
| 15 | M&L for Non Skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors laid over and including 15mm thick screed bed for laying floor finishes in CM (1:6) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles including dismantling of old tiles from its positions complete all as specified and as directed. |
| 16 | M&L for Non Skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors laid over and including 15mm thick screed bed for laying floor finishes in CM (1:6) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles including dismantling of old tiles from its positions complete all as specified and as directed. |
| 17 | M&L for Glazed ceramic coloured tiles in vertical surface 350x 250x 7mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of tile laid over and including backing coat of 10 mm thick in CM (1:4) including dismantling of old tiles from its positions complete all as specified and as directed. |
| 18 | M&L for PCC (1:4:8) type D-2,75 mm thick (using 40mm graded stone aggregate) as in sub base of floor complete all as specified and as directed. |
| 19 | M&L for chequered cement concrete tiles of Size 20cm x 20 cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and pigments, laid over and including 15mm thick screed bed for laying floor finishes in cement mortar (1:4) including dismantling of old tiles from its positions complete all as specified and as directed. |
| 20 | M&L for cement concrete tiles of size 25cm x 25cm x 22mm thick, with grey cement and no pigment laid over 15 mm thick screed in CM (1:4) mixed with water proofing compound ,joints grouted and flush pointed in CM (1:3) mixed with 5% of crude oil by weigt of cement complete all as specified and as directed. |
| 21 | M&L for Preparing the sunken floor slab grouting as specified and applying cement plaster coat laid to slope average 20mm thick in CM (1:3) finished even and fair and applying evenly a tack coat of industrial bitumen 85/25 @ the rate of 1.2 kg per sqm complete all as specified and as directed. |
| 22 | M&L for Water proofing treatment by applying bituminous primer @ 1.2 kg/sqm providing and laying 3mm thick APP modified water proofing membrane weighing not less then 3.00 kg/sqm reinforced with non woven polyster matt weighing not less then 150gm/sqm having soften point not less then 140 degree centi grade, longitudinal tensile strength not less then 650N/Sqm, tearing strength of 180 N, by torch application including min 10cm side over lap and 15cm end over lap and over the membrane and then applying one coat of bitumen based UV reflective aluminium paint @ 0.10 kg /sqm applied on treated bituminous membrane complete all as specified and as directed. |
| 23 | M&L for screed bed 10 mm thick in cement mortar (1:4) on brick/concrete roof surfaces, using WPC @ 2% by weight of cemnt (WPC measured and paid separately), surfaces finished even and smooth without using extra cement complete all as specified and as directed. |
| 24 | S&F Pressed steel frames of size 105 X 60mm (Thickness of MS Sheet 1.25mm) for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate,with and including filling hollow of frame with PCC (1:3:6) type C-0 (using 12.5 mm graded stone aggregate) complete all as specified and directed. |
| 25 | S&F Pressed steel frames of size 125 X 60mm (Thickness of MS Sheet 1.25mm) for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate,with and including filling hollow of frame with PCC (1:3:6) type C-0 (using 12.5 mm graded stone aggregate) complete all as specified and directed. |
| 26 | M&L for 2nd class hard wood plain solid straight chowkats and frames wrought framed rebated on the solid rounded or chamfered put together with glue pined joints complete all as specified and as directed. |
| 27 | S&F 35mm thick factory made Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed. |
| 28 | M&L for 0.90mm thick Decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions complete all as specified and directed. |
| 29 | S&F 30 mm thick factory made second class hard wood glazed and skelton shutter, open rebated and prepared to receive glass, gauze etc (without sash bar ) edges of framing plain, camfered or rounded, fitted with cut and mitred beads for securing glass etc size of members of shutters as specified in SSR Part -I section 8 clause 8.42(a) supplied and fitted to chowkat complete all as specified and directed. |
| 30 | Supply and fix stainless steel wire cloth 0.36 nominal dia of wire and average width apperture 1.40mm and fixed with stainless steel wire staples or wooden beads supplied with shutter etc complete all as specified and directed. Please Enable Macros to View BoQ information |
| 31 | Supply and fix stainless steel wire cloth 0.36 nominal dia of wire and average width apperture 1.40mm and fixed with stainless steel wire staples or wooden beads supplied with shutter etc complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 07, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 27, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 10 daysAug 29, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 12 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender