Tender For Repair, Renovation And Additional Works Of Sub-Center Kumdaim At Phc Marcaim Under Xvth Fc Health Grants.
Tender Value
33.44 Lakhs
Estimated cost
Bid Submission
31 Aug 2026
6 days left
EMD
66897
Bank guarantee accepted
Document Fee
4000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
goa → Goa
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair, Renovation And Additional Works Of Sub-Center Kumdaim At Phc Marcaim Under Xvth Fc Health Grants.
Corrigendum
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 21-Aug-2026 | Bid Auto Extn Corrigendum | Bid Auto Extn Corrigendum | 31-Aug-2026 |
BOQ
| Sl. No. | Item Description |
| 1 | Earthwork in excavation by mechanical means (hydraulic excavator)/manual means in foundation pipeline trenches drain (not exceeding 1.5 m in width or 10 sq.m. on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m including getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50 m. a)All kinds of soil |
| 2 | Earthwork in excavation by mechanical means (hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sq.m on plan) including disposal of excavated earth lead upto 50 m and lift upto 1.5m disposed earth to be leveled and neatly dressed including providing barricading, danger lighting guarding as directed in : b) All types of Ordinary rock including all types of laterite rock, blasting prohibited |
| 3 | Supplying and filling in plinth under floors, trenches including watering ramming consolidating, dressing, complete. b)Moorum |
| 4 | Rubble packing with hard laterite stone under floors including watering ramming and consolidating etc. in pipeline trenches and other foundations complete. |
| 5 | Laterite masonry in neatly dressed stones of size as specified in cement mortar 1: 4 (1 cement : 4 coarse sand) in foundation and basement. |
| 6 | Laterite masonry in neatly dressed stones for 23 cms thick masonry walls in c.m. 1 : 4 (1 cement : 4 coarse sand in foundation upto plinth level |
| 7 | Extra for laterite masonry in all sizes in superstructure from floor I level upto floor V level. |
| 8 | Providing and laying in position cement concrete 1:2:4 (1 cement : 2 coarse sand: 4 graded granitic or basaltic stone aggregate 40 m nominal size) excluding cost of centering, shuttering and finishing : a)All works upto plinth level |
| 9 | Providing and laying in position (1:11/2:3) Reinforced cement conrete excluding the cost of centering, shuttering, finishing and reinfrocement (1 cement: 1½ coarse sand:3 graded stone agg 20mm nominal size) c) In beams, suspended floors, roofs having slope upto 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases upto floor five level |
| 10 | Reinforced cement concrete work 1:1½:3 (1 cement: 1½ coarse sand: 3 granitic or basaltic stone aggreate 20mm nominal size excluding plastering and cost of centering, shuttering & reinforcement, in sloping or battering surface (slabs, beams, louvers, etc) iv) Sides and Soffits of beams, Beam Haunchings, Cantilever, Girders, Bressumers and Lintels plinth beams not exceeding 1m in depth |
| 11 | Providing TMT steel reinforcement bars of (SAIL, TATA. VIZAG, JSW Steel Ltd.) ) (Confirming to IS 1786 of 1986) for RCC work (conforming to I.S. 1786 of 1986) including bending, binding & placing in position in all the floors along with the factory made precast concrete cover blocks of specified sizes whose compressive strength is not less than that of surrounding concrete in the structural member. |
| 12 | FRP (Fiber Reinforced Polymer) Frames with Wood FinishManufacture, Supply and Installation (with anchor fastener) of EPEE or equivalent Goan make FRP (Fiber Reinforced Polymer) Frame of cross section as per options below with right angle joint and FRP (Fiber Reinforced Polymer) laminate made from 450 grams per sq.mts (gsm) chop strand glass fiber (matt) and unsaturated polyester resin with viscosity range of 400/450 centipoises per second (cps). The core of frame would be filled with seasoned wood as infill material. The slot of frame for door resting will be of suitable width so as to take specified thickness door. The frame will be water proof as well as mild acid/ alkali resistant manufactured in an ISO 9001- 2015 certified company. Specified Cross Section 4'' x 2'' |
| 13 | Wood Finish Foam Core FRP (Fiber Reinforced Polymer) Door Shutter Manufacture, Supply and Installation (including accessories as mentioned below) of EPEE or equivalent Goan make FRP (Fiber Reinforced Polymer) door shutter of specified thickness as per options below by using tray system, with seasoned hard wood, moisture less than 17%, wood styles for Top rail and lock rails. FRP (Fiber Reinforced Polymer) laminate made up of 450 grams per sq.mts (gsm) chop strand matt and unsaturated polyester resin with viscosity range of 400/450 centipoises per second (cps) along with printed matt having wooden textures, used along with UV Resistant resin to give the clear wooden texture on the door. The core of shutter will be filled as specified (Expanded Polystyrene Foam / Polyurethane Foam (EPS/PU) Foam) The shutter to be water proof as well as mild acid / alkali resistant manufactured using RV TIFAC (R V Engineering College, Bangalore & Technology Information Forecasting & Assessment Council) Technology in line with IS 13034 1990 test Standard in an ISO 9001 – 2015 certified factory. Accessories:i) S. S. Hinges 4” - 3 Noii) S. S. Latch - 1 Noiii) Tower Bolt 5” - 2 Nosiv) Handle 5” - 2 NosShutter Thickness 30mm |
| 14 | UPVC ONLY DOOR FRAME:- Providing & fixing Upvc Door Frame Yashashri make or equivalent made out of Upvc extruded multi cavity frame of 60 mm x 60mm x 2mm wall thickness. Frame is reinforced with G.I. Channel & welded in corners with Average weight 0.80 kg per running mtr. These frames are tested by using BS 2782 & DIN 53459 test methods. |
| 15 | THREE TRACK SLIDING WINDOWS:- Providing & fixing Three track Sliding Windows Yashashri make or equivalent, made out of 97mm x 43mm x 2mm upvc multi-cavity reinforced with G.I. channel and having up word projection for sliding of shutter on Nylon Rollers and having slope for draining rain water outside and welded in corners. Shutters are made out of 57mm x 31mm x 2mm multi-cavity section having provision for nylon rollers fixing, glass fixing with EPDM gasket, glass bead and welded in corners. In Three Track Sliding window 4mm clear glass is used. The average weight of Three Track Sliding window is 16.5 kg per sq mtr. These Upvc sections are tested by using BS 2782 & DIN 53459 test methods. |
| 16 | FALSE CEILING:- Providing & fixing False Ceiling Yashashri make or equivalent, made out of 2” x 1” M.S sq tube frame support structure & 20mm x 155mm x 1.2mm multi-cavity upvc section, 30mm x 40mm x 2mm Upvc multi-cavity section with hidden screwing system. The average weight of False Ceiling is 8.50 kg per sq mtr. These Upvc sections are tested by using BS 2782 & DIN 53459 test methods. |
| 17 | PARTITION:- Providing & fixing Partitions Yashashri make or equivalent, made out of frame support structure in 2” x 1” M.S. sq tube & walls paneled by 20mm x 155mm x 1.2mm Upvc multi cavity section fixed on structure with hidden screwing system. Door frame & shutter made out of 50mm x 50mm x 2.5mm & 31mm x 150mm x 1.5mm Upvc multi cavity section. Some portion of partition can be made by 4mm fixed glass. The average weight of Partition is 17 kg per sq mtr. These Upvc sections are tested by using BS 2782 & DIN 53459 test methods |
| 18 | Providing and fixing flush door shutter of solid core melamine face three layered, prelaminated wood based particle board exterior grade having shade of choice on both sides (PTX) or having shade of choice on one side and balancing lamination on the other side (PLX) as per IS 3087 (1985) type I on the edge of Novopan or equivalent bonded with BWR/BWP synthetic resin with second class teak wood, lipping of section of size 12 mm x 30 mm flange and 18 mm x 10 mm web (18 mm deep) fixed into 18 x 10 mm groves of shutter with water resistant adhesive and fully threaded G.I. screws 50 mm not more than 450 mm centre to centre including anodized aluminium butt hinges with necessary screws etc. complete. Commercial on both faces: 1) 35 mm thick |
| 19 | Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc.with hairline finish, including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 20 | Supply and installation of Aluminium Louvers. The frame should be made of Aluminium tubes of size 100x50X1.50 mm thk and 50X25x1.50 mm thk C channels. Aluminium Z shaped louvers of 100mm should be fixed to the supporting frame with aluminium cleats, GI screws, etc complete. The whole assembly is powder coated with pure polyester paint. (MS framing to be paid separately) |
| 21 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) (Square Hollow Section (SHS) IS4923 /Rectangular Hollow Section (RHS) IS4923/ Circular Hollow Section (CHS) IS1161 closed Structural Steel of (SAIL, TATA. VIZAG, JSW ,APOLLO Steel Ltd.) make (Min Yeild Stress 310 Mpa)) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. |
| 22 | Cuddappah stone slab machine cut flooring over 20mm (average) thickness of cement mortar 1:4 (1 cement : 4 coarse sand laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete - 25 mm thick. |
| 23 | Providing and fixing coloured ceramic tiles spartek or equivalent of 8\\" x 8\\" size and 6 mm thick in skirting and dados on 12 thick cement plaster 1:3 (1 cement : 3 coarse sand) and jointed with cement slurry complete. |
| 24 | Providing and laying 20mm thick cuddapah in shelves over 20 mm thick base of cement mortar 1:3 complete |
| 25 | Providing 25 mm thick cuddapah slabs machine cut and polished on either side in partitions including making necessary grooves in the wall and fixing with cement mortar, complete as directed by the engineer-in-charge |
| 26 | Providing and fixing vitrified matt finished (600x600) and 10mm thick tiles in floor, treads of steps, landing on 25mm thick bed of cement mortar 1:3 and jointed with cement slurry complete. |
| 27 | Providing and fixing vitrified antiskid tiles (320x320) and 10mm thick tiles in floor, treads of steps, landing on 25mm thick bed of cement mortar 1:3 and jointed with cement slurry complete. |
| 28 | Providing and and laying scratch resistant floor tiles in different sizes of Johnson, Somany, Kajaria (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make in colours and shades as specified laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand) including grouting the joints with white cement and matching pigment etc., complete a)600x 600 mm Dark Shades |
| 29 | Providing and fixing Granite stone slabs (mirror polished) 18mm thick in risers of steps, skirting, dado and pillars laid on cement paste and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete a)Jet black |
| 30 | Providing and laying in design & pattern factory made PVC RUBBER MOULDED Interlocking Cement Concrete paver blocks of M35/M40 strength, thickness & size/shape, made by table vibratory method using Rubber mould, laid in required colour & pattern over 50mm thick compacted bed of fine sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with river/manufactured sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand in footpath, parks, lawns, drive ways or light traffic parking etc. complete as per manufacturer’s specifications & direction of Engineer. a)60mm thick -Grey colour (M35 grade) |
| 31 | Providing & laying six courses water proofing treatment with bitumen felt over roofs consisting of first, third and fifth courses of blown or/and residual bitumen applied hot at 1.45 1.20 and 1.7kg., per sq.m. of area respectively second and fourth course of roofing felt type 3 grade 1 (hessian based self finished bitumen felt ) & sixth and final course of stone grit 6 mm and down size or grade gravel spread at 0.008 cu.m per sq. m excluding grading complete a)Providing and fixing colour coated galvulium roofing sheets of 0.5mm thickness including all the accessories (TATA make) but excluding the cost of purlins, rafters, trusses, flashings etc. complete as per the directions of the Engineer in charge. |
| 32 | Providing and fixing PVC SWR pipes confirming to IS 13592 type A including jointing with seal ring confirming to IS 5382 leaving 10 mm gap for thermal expansion. |
| 33 | Providing and fixing Prince or equivalent make PVC SWR half round eaves gutter with bolts, nuts and flat iron brackets 40 x 3 mm size complete a)140 mm nominal size |
| 34 | 12mm cement plaster 1:4 (1 cement : 4 fine sand) |
| 35 | 18mm cement plaster in two coats under layer 12mm thick cement plaster 1:5 ( 1 cement : 5 coarse sand) and top layer 6mm thick with cement plaster 1: 3 (1 cement : 3 coarse sand) finished with sponge. |
| 36 | Finishing fine with neeru over plaster |
| 37 | Applying one coat of cement primer of approved brand and manufacture on wall surface. |
| 38 | Applying one coat of distemper primer of approved brand and manufacture on wall surface |
| 39 | Finishing wall with superior quality waterproofing cement paint (super snow hem or equivalent) of required shade on new work (three or more coats) to give an even shade |
| 40 | Painting (two or more coats) with synthetic enamel paint of approved brand and manufacture in all shade or new work over and under coat of suitable shade with ordinary paint of approved brand and manufacture to give an even shade |
| 41 | Repairs to plaster in patches of 2.5 sq.m. and under including cutting the patch in proper shape and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50m lead.With cement mortar 1:4 (1 cement : 4 fine sand) |
| 42 | Demolishing cement concrete 1:3:6 or richer mix including disposal of material within 50 m lead. |
| 43 | Demolishing laterite stone masonry in cement mortar including stacking of serviceable material & disposal of unserviceable material within 50 mts. lead. |
| 44 | Dismantling doors, windows and clearestory windows (steel or wood) shutters including chowkhats architrave holdfast etc. complete and staking within 50 mt. Lead a)Of area 3 sq.m. and below |
| 45 | Dismantling the tile work in floors and roofs laid in cement including stacking of materials within 50 meters lead for thickness of tiles 10mm to 25mm. |
| 46 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 mts. lead. |
| 47 | Providing and fixing M.S. grill of required pattern in wooden frames of Windows etc. with M.S. flats square or round bars with round headed bolts and nuts or by by screws. b)Ornamental grill |
| 48 | Proving and fixing white vitreous china water closet squating (European type w.c. pan) with seat and lid, C.P. brass hinges and rubber buffers 10 lts. High level P.V.C.. flushing cistern (of approved make ) with fittings, rack bolts 32 mm diameter P.V.C. telescopic flush pipe with fit tings and clamps 25mm P.V.C.. over flow pipe with specials & mosquito proof coupling of approved municipal design and nylon. chain and pull complete, cutting and making good the walls ad floors where required. a)W.C. pan with white plastic seat and lid. |
| 49 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430 x 260 x 350 mm and 340 x 430 x 265 mm sizes respectively with pvc automatic flushing cistern with fittings, R.S. or C.I. brackets, standard size galvanised steel flush pipe and spreaders with brass unions & G.I. clamps complete, including painting of cister and fittings, cutting and making good the walls and floors where required. b)Range of two urinal basin with 10 litres pvc. Automatic flushing |
| 50 | Proving and fixing kitchen sink with R.S. or C.I. brackets C.P. brass chain with rubber plug 40 mm C.P. brass waste and 40mm M.I. or C.P. brass trap necessary unions complete, including painting the fittings, cutting and making good the walls where required. a)White vitreous china sink size 600 x 450 x 200 mm |
| 51 | Providing & fixing (4’) 100 mm sand cast iron grating for gully floor or nahni trap. |
| 52 | Providing and fixing 600 x 450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick asbestos sheet ground fixed to wooden cleats with C. P. brass screws and washers. |
| 53 | Providing & fixing c.p. brass towel rail complete with C.P. brass brackets fixed to wooden cleats with C. P. brass screws b)600 x 20 mm size |
| 54 | Providing and fixing toilet paper holder : a)C.P. brass |
| 55 | Providing & fixing soap dish chromium plated with brackets fixed to wooden cleats with CP brass screw |
| 56 | Providing and fixing brass stop cock (heavy) of approved quality : a)15 mm nominal bore |
| 57 | Providing and fixing brass stop cock (heavy) of approved quality : a)20 mm nominal bore |
| 58 | Providing and fixing brass full way valve (heavy) duty with wheel of approved quality : b)20 mm nominal bore |
| 59 | Providing and fixing ball valve (brass) of approved quality : a-1) High pressure with P.V.C. floats: 15 mm nominal bore |
| 60 | Providing and fixing P.V.C. connection pipe with brass unions 15 mm nominal bore: c)45 cm (18”) length . |
| 61 | Providing and fixing normal gauge polythene pipes of approved quality complete with special flange compression type fitting (of approved make) including trenching ad refilling etc (external work) (high density): b)32 mm nominal bore |
| 62 | Providing and placing on terrace roof of floor two (1st flor roof single piece rotational moulded polythene water storage tank having I S I mark and conforming to I S 12701; 1996. c)1000 lit. capacity |
| 63 | Providing and placing on terrace roof of floor two (1st flor roof single piece rotational moulded polythene water storage tank having I S I mark and conforming to I S 12701; 1996. c)500 lit. capacity |
| 64 | Constructing brick masonry manhole or inspection chamber with second class bricks in cement mortar 1:5 (1 cement :5 fine sand) R.C.C. top slab with 1: 1 1/2:3 mix (1 cement: 1 1/2 coarse sand ;3 graded stone aggregate 20mm nominal size foundation concrete 1:1 1/2:3 mix (1 cemet ;1 1/2 coarse sand :8 graded stone agrregate 20mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 20 mm nominal size) neatly finished complete as per standard design. d)Inside size 60 x 60cm and 60cm deep including C.I. cover with frame (light duty) 455x610mm internal diameter total weight of cover and frame to be not less than 38 kg. (weight of cover 23 kg). |
| 65 | Making soak pit. 2.5 m dia 3 m deep with 45x45 cm dry brick honey comb shaft and S.W. drain pipe 100 mm diameter, 1.8 m long complete filled with laterite stone aggregate 125 to 180 mm surrounded by laterite stone aggregate of 40 mm and down gauge as per standard design. |
| 66 | Providing and fixing rigid PVC S.W.R. (soil, waste & rain water drainage pipes of approved including lubricant etc. complete (single/double) socketed: a)110 mm dia |
| 67 | Providing and fixing rigid PVC S.W.R. (soil, waste & rain water drainage pipes of approved including lubricant etc. complete (single/double) socketed: b)75 mm dia |
| 68 | Providing and fixing rigid PVC bend of required degree (of approved make) for S.W.R. drainage pipes of approved including lubricating. a) 110 mm dia |
| 69 | Providing and fixing rigid PVC bend of required degree (of approved make) for S.W.R. drainage pipes of approved including lubricating. a) 75 mm dia |
| 70 | Providing and fixing rigid PVC bend (approved make ) for S.W.R. pipes including lubricating etc complete bend with door : a)100 mm dia |
| 71 | Providing and fixing rigid PVC bend (approved make ) for S.W.R. pipes including lubricating etc complete bend with door : a)75 mm dia |
| 72 | Providing and fixing chlorinated ployvinyl chloride (CPVC) pipes confirming to IS:15778, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1 mt. spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of the Engineer-in-charge. Internal work exposed on wall (Medium duty SDR 13.5 pipe). a)15 mm outer dia CPVC pipe |
| 73 | Providing and fixing chlorinated ployvinyl chloride (CPVC) pipes confirming to IS:15778, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1 mt. spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of the Engineer-in-charge. Internal work exposed on wall (Medium duty SDR 13.5 pipe). a)20 mm outer dia CPVC pipe |
| 74 | Providing and fixing chlorinated ployvinyl chloride (CPVC) pipes confirming to IS:15778, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1 mt. spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of the Engineer-in-charge. Concealed work (medium duty SDR 13.5 pipe) including cutting chases and making good the walls etc. b)20 mm dia nominal outer dia pipes. |
| 75 | Providing and fixing chlorinated ployvinyl chloride (CPVC) pipes confirming to IS:15778, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1 mt. spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of the Engineer-in-charge. Concealed work (medium duty SDR 13.5 pipe) including cutting chases and making good the walls etc. c)25 mm dia nominal outer dia pipes. |
| 76 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 including cutting of stone and making good the walls wherever required : Kitchen sink with drain board with coupling & all accessories complete with choke stop strainer, Plain type having flat borders for correct sandwithing between the plaform top and bottom slabs complete a)Overall size 1040mmx510mm (41\\"x20\\") bowl size 460mmx410mmx200mm (18\\"x 16\\"x 8\\") depth 200 mm. Glossy. 1.0mm thk, |
| 77 | Providing and fixing NICKEL chrome plated copper alloy Fancy Bib Cock with extended lever handle and wall flange Confirming to IS 8931; 1993 15mm nominal bore |
| 78 | Providing and fixing NICKEL chrome plated copper alloy Fancy Pillar Cock with extended lever handle and wall flange Confirming to IS 8931; 1993 15mm nominal bore |
| 79 | Supplying and erecting LED square / circular Max. 14 W downlighter/Panel Light having pressure die-cast aluminium housing, polystyrenediffuser having system lumens output of Min. 1500 Lumens, min. efficacy of110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. rippleof 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, having mountingarrangement with board for surface type or spring loaded mounting clips |
| 80 | Supply and erecting of 9 inch (225 mm sweep) exhaust fan with double ball bearings, 1400 rpm, complete with all accessories. |
| 81 | Supplying and erecting anodized aluminium corridor / passage light LEDfitting (4 feet) Max. 22W with high transitivity diffuser with system lumensoutput of Min.2200 lumens , min. efficacy of 100 lumen/W, CRI>80, CCTupto 6000K, Beam Angle of 110 deg., Ripple<5%, THD<10%, p.f. >0.95,operating range of 200-270V, surge protection of 2 kV, Life class of 50,000 Hrs.at L70B50, including driver, with end caps on provided PVC Block / woodenboard with 3 years warranty |
| 82 | Supply and erecting of 48 inch ( 1200mm sweep) ceiling fan, double ball bearing type, , complete with all accessories. CAT A |
| 83 | Supplying and erecting LED square / circular Max. 11 W downlighter/Panel Light having pressure die-cast aluminium housing, polystyrenediffuser having system lumens output of Min. 1200 Lumens, min. efficacy of110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. rippleof 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, having mountingarrangement with board for surface type or spring loaded mounting clipscomplete with 3 years warranty. |
| 84 | Supplying and fixing following way TPN sheet steel, single door, Horizontal type MCB distribution board 415 V on surface/ recess complete with tinned copper busbar neutral busbar earth bar dinnbar detachable gland plate interconnections phosphotized and powder painted including earthing etc. as required ( but without MCB/RCCB/Isolator) 6way (8+18), double door, Horizontal type Cat B |
| 85 | Supplying and fixing 6 A to 32 A, C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required.(a) SP, Cat A |
| 86 | Supplying and fixing 32 A, C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required. (e) TPN, Cat B |
| 87 | Supplying and fixing following rating four pole (triple pole and neutral) 415 V RCCB having a sensitivity current upto 300mA in the existing MCB DB complete with connections testing and commissioning etc as required'(b) 40 A, Cat A |
| 88 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable in the independent surface / recess PVC conduit ( medium)of appropriate size as required.'(b) 2 x 2.5 sq.mm + 1 x 2.5 sq.mm earthwire (20mm Conduit) |
| 89 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable in the independent surface / recess PVC conduit ( medium)of appropriate size as required.2 x 4 sq.mm + 1 x 4 sq.mm earthwire (20mm Conduit) |
| 90 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable in the independent surface / recess PVC conduit ( medium)of appropriate size as required.'4 x 4 sq.mm + 2 x 4 sq.mm earthwire (25mm Conduit) |
| 91 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in recessed PVC conduit(heavy) with modular switch, modular plates, suitable size modular GI box of specified Category and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group B -- with Cat A Modular Accessories |
| 92 | Supplying and fixing 3 pin 5/6 A modular socket outlet and 5/ 6 A modular switch on board the modular surface/recessed PVC/GI modular box by suitably increasing its modular capacity, modular plate and cover including connection painting etc. as required. |
| 93 | Wiring for group controlled light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in recessed PVC conduit(heavy) and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. |
| 94 | Supplying and fixing suitable size modular PVC box with modular plate and cover in front on surface or in recess including providing and fixing 1 no 6 pin 15/16 A modular socket outlet and 1 nos 15/ 16 A modular switch connection painting etc. as required. ( For workstations)(a) Cat A |
| 95 | Supplying and fixing 3 pin 5/6 A modular socket outlet and 5/ 6 A modular switch on board the modular surface/recessed PVC/GI modular box by suitably increasing its modular capacity, modular plate and cover including connection painting etc. as required. |
| 96 | Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required (b) Cat B |
| 97 | Supply and erecting fan hook box ( 100 mm diameter or equivalent square size, 75mm deep) fabricated out of 16 SWG sheet steel with 10 m round bar hook bounded to RCC steel upto 50 mm length protruding on each side of the box, including painting with 2 coats of red oxide, complete as required. |
| 98 | Supplying, installing, testing & commissioning split type variable speed inverter technology with minimum 3 to 1 convertible mode for compressor, room air conditioning unit 1.3TR to 1.6TR capacity having ISEER minimum 3.8 to maximum 4.39 suitable to operate on 250V, 50 Hz, A.C. supply having 1 no of air handling unit hi-wall/floor mounting type complete with refrigerant R32 having copper condenser, minimum 2.5PM filter, self diagnosis feature, stabilizer free operation & temperature display on indoor unit, noise level maximum 50dBA at position as per specification no. AP-AC/ SAC |
| 99 | Supplying & erecting seamless outside & inside, smooth, dry and clean copper pipe with ROHS compliant suitable for refrigerant having 22SWG thickness and inner dia/size 12mm complete as per specification no. AP/AC-CP |
| 100 | Supplying & erecting seamless outside & inside, smooth, dry and clean copper pipe with ROHS compliant suitable for refrigerant having 22SWG thickness and inner dia/size 16mm complete as per specification no. AP/AC-CP |
| 101 | Supplying and erecting fully automatic line Voltage stabilizer buck and boost type for operation on input voltage 160 to 270V and output voltage 200 to 250V rated for, 1 kVA maximum load and with voltmeter, selector switch, 6A/16A flush type 3 pin socket for output and with 3 core flexible cord and 3 pin 6/16A plug top |
| 102 | Supplying and erecting elastomeric nitrile rubber / foam tube type sleeves for coating and insulating on provided PC / copper pipes having 9 mm thickness and inner diameter / sizes 12 mm for solar water heater /AC system |
| 103 | Supplying and erecting elastomeric nitrile rubber / foam tube type sleeves for coating and insulating on provided PC / copper pipes having 9 mm thickness and inner diameter / sizes 16 mm for solar water heater /AC system |
| 104 | Supplying and erecting HMS PVC conduit 20mm dia. with PVC accessories on wall/ceiling as per specification no. WG-MA/CON. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 21, 2026
11:30 IST
Tender Published
Tender notice published.
Completed
Aug 31, 2026
18:00 IST
Corrigendum-1 Issued
Clarifications on tender conditions and amendments issued.
Upcoming · 6 daysAug 31, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 6 daysSep 03, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 9 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender