Tender For Replacement Of Bare Conductor By Ab Cable In 11 Kv Shantipuri Feeder In Jawahar Nagar, Shantipuri No.-2, 3, 4 Emanating From 33/11 Kv S/S Pantnagar Under Edd, Kichha Under The Head Of Capital (S.I.).( Rates Should Be Quoted Without Gst) (G
Tender Value
Ref. Documents
Estimated cost
Bid Submission
24 Aug 2026
0 days left
EMD
1.08 Lakhs
Bank guarantee accepted
Document Fee
5900
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Udam Singh Nagar → Uttarakhand
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Replacement Of Bare Conductor By Ab Cable In 11 Kv Shantipuri Feeder In Jawahar Nagar, Shantipuri No.-2, 3, 4 Emanating From 33/11 Kv S/S Pantnagar Under Edd, Kichha Under The Head Of Capital (S.I.).( Rates Should Be Quoted Without Gst) (Gst Will Paid Extra)
BOQ
| Sl. No. | Item Description |
| 1 | Annexure-A (LABOUR CHARGES) |
| 2 | Excavation of earth for stay pit of size 0.6x0.6x1.2 mtr in all types of soil including proper dressing of sides and ramming of bottom including getting out the excavated soil and disposal of surplus excavated soil as directed complete work |
| 3 | Fixing, tightening and nozzling of stay with pole and stay rod on required tension as per drawing/manual in LT line |
| 4 | Grouting of Stay in size 0.6x0.6x0.3 in CC ratio 1:4:8 (1 cement : 4 graded stone 20mm nominal size : 8 coarse sand ) block including cost of Cement, sand and stone ballast back filling of soil and boulders in pit and ramming and proper alignment, leveling as per RESSPO Manual. |
| 5 | Excavation of earth for pole pit of size 0.9x0.6x1/6 of full length of pole for erection of pole in all types of soil including proper dressing of sides and ramming of bottom including etting out the excavated soil and disposal of surplus excavated soil as directed complete work |
| 6 | Erection of PCC single support pole in proper level and alignment along with fixing of all accessories like top channel,& clamps as per RESPO manual. |
| 7 | Erection of SP-33 single support pole in proper level and alignment along with fixing of all accessories like top channel & clamps as per RESPO manual. |
| 8 | Grouting of pole in size 0.45x0.45x1/9 of the support in CC ration 1:4:8(1 cement:4 graded stone20 mm niminal size: 8 coarse sand) block including cost of cement, sand and stone ballast back filling of soil and boulders in pit and ramming and proper alignment, levelling as per RESPO cnstruction manual. |
| 9 | Dismantling of existing LT line 1P 2W including disc fitting, Insulator, clamps, Nut & Bolts and consumer connections and Street light connections etc. including rolling of conductor and cartage back from site to JE store(ACSR Weasel) |
| 10 | Dismantling of existing LT line 2P 3W including disc fitting, Insulator, clamps, Nut & Bolts and consumer connections and Street light connections etc. including rolling of conductor and cartage back from site to JE store(ACSR Weasel) |
| 11 | Dismantling of existing LT line 3P 4W including disc fitting, Insulator, clamps, Nut & Bolts and consumer connections and Street light connections etc. including rolling of conductor and cartage back from site to JE store(ACSR Weasel) |
| 12 | Laying and erection of L.T. PVC Cable including crimping of lugs of size 1x70,120, 150 Sq.mm. (Including all cost of material) |
| 13 | Laying/Erection & Commissioning of LT AB Cable of size 3x95+1x70 Sq.MM |
| 14 | Cartage of PCC Poles from store centre to construction site with loading, unloading at both points and proper stacking.(Distance 21-50 Km) |
| 15 | Cartage of ST pole SP-33 Poles from store centre to construction site with loading, unloading at both points and proper stacking.(Distance 21-50 Km) |
| 16 | Cartage of other material (other than poles) by vehicle from Store Center to nearest construction site Store including loading and unloading at both ends(distance 21-50 Km) |
| 17 | Headload cartage of PCC Pole from road to site (distance 0-1 Km) |
| 18 | Headload cartage of SP-33 Pole from road to site (distance 0-1 Km) |
| 19 | Head load cartage of small material(distance 1-3 Km) |
| 20 | Disconnection & Reconnection of Consumer. |
| 21 | Tightening of Stay Set as per Direction of Engineer in Charge. |
| 22 | Straightening of Tilted STP Poles as per Direction of Engineer in Charge. |
| 23 | Fixing of PG Clamp L2L 50-50 Sq.MM. |
| 24 | Fixing of PG Clamp L2B 50-25 Sq.MM. |
| 25 | Fixing of MS Clamp as per Direction of Engineer in Charge. |
| 26 | Installation of LT Distribution Box 3 Phase for LT AB Cable. |
| 27 | Erection of Dead End Clamp as per Direction of Engineer in Charge. |
| 28 | Erection of Suspension Clamp with I hook as per Direction of Engineer in Charge. |
| 29 | Fixing of Piercing Connector L2B 95-25 Sq.MM. |
| 30 | Fixing of Piercing Connector 120-35 Sq.MM. |
| 31 | Back Carriage of Scrap Material. |
| 32 | Lopping Chopping of Tree Branches near HT/LT Line. |
| 33 | Annexure-B (SUPPLY ITEMS)(As per UPCL Norms) |
| 34 | Supply of Suspension Clamp with I Hook (Ins.) Clamp, N&B |
| 35 | Supply of MS Clamp with N&B for LT Distribution Box |
| 36 | Supply of MS Clmap for Dead End Clamp with N&B |
| 37 | Supply of LT Bare N.Conn.PG. Clamp for DB 95-95 Sq.mm |
| 38 | Supply of Dead End Clamp with I Hook. |
| 39 | Supply of Stay Insulator. |
| 40 | Supply of insulated Piercing connector body molded from high quality mechanical climate and UV resistant glass reinforced polyamide, hot dipped galvanized bolts & contact teeth ABC size 95 Sqmm to 25 Sqmm TYCO/RPG/3M Make. |
| 41 | Supply of insulated Piercing connector body molded from high quality mechanical climate and UV resistant glass reinforced polyamide, hot dipped galvanized bolts & contact teeth ABC size 120 Sqmm to 95 Sqmm TYCO/RPG/3M Make. |
| 42 | Supply of MS Clamp with N&B for Suspension Clamp |
| 43 | Supply of LT Bare N.Conn.PG. Clamp for L-L 95-95 Sq.mm |
| 44 | Supply of PG Clamp |
| 45 | Supply of SMC Three Phase L.T. Distribution Box with inbuilt panal lock, Al bus bar RYB 25x6mm., Al Busbar N. 40x6mm. for connection of L.T. consumer (Sintex/RMC make or other ISO reputed company) with Panel Lock with key) (As per drawing attached) |
| 46 | Supply of MS Flat 35x5MM Set for Distribution Box with N&B |
| 47 | Supply of Al. Lugs long barrel 120 SQ.MM |
| 48 | Supply of Al. Lugs 25 SQ.MM Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 07, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 24, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
TodayAug 25, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 1 dayTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender