Tender For Special Repair To Certain Jcos/Or Md Accn At Shekhawati Line, Npg Line & Hazipir Line Under Ge (West), Delhi Cantt-10
Tender Value
6.70 Crore
Estimated cost
Bid Submission
05 Sep 2026
20 days left
EMD
6.60 Lakhs
Bank guarantee accepted
Document Fee
3000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
New Delhi → Delhi
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repair To Certain Jcos/Or Md Accn At Shekhawati Line, Npg Line & Hazipir Line Under Ge (West), Delhi Cantt-10
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete (unreinforced) of any description and in any position not other specifically provided, removal of debries beyond MoD lands complete all as specified and directed. |
| 2 | Dismantling of brick tiles or terracing tiles single layer on roof complete all as specified and directed. |
| 3 | Demolition of mud phuska on roof slabs, any thickness including cleaning of roof surfaces and removal of debries beyond MoD lands complete all as specified and directed. |
| 4 | Scraping old tar from roof treatment over concrete padding of any thickness etc from roof including finishes or junction or parapet and cleaning the surface completely complete all as specified and ditrected. |
| 5 | M&L for providing cement concrete 1:2:4 type B-I 20mm graded in roof kerb or mud slops, rounded or chamfered on edges, plinth courses, coping, kneelers, apex stone, kerb water tough and the like including weathering, slightly rounded or chamfered angles and throating as directed) complete including necessary form work complete all as specified and directed. |
| 6 | S&F for Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface up to 3 cuts complete, including providing skirting up to 150 mm height along the parapet walls in the same manner incl 15mm thick screed bed in CM1:4 complete all as specified and directed. |
| 7 | M&L for cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) on roof padding with water proofing compound surface finished even and smooth without using extra cement complete all as specified and directed.(Note : Supply only WPC shall be measured and paid separately) |
| 8 | Demolition of brick work built in cement /lime mortor in any position / situation in walls / parapets complete all as specified and directed. |
| 9 | M&L for brick work with sub class 'B' brick straight or curved on plan exc. 6 mtr mean radius built in cement mortor 1:6 complete all as specified and directed. |
| 10 | M&L for half brick work with sub class 'B' brick straight or curved on plan exc. 6 mtr mean radius built in cement mortor 1:6. Complete all as specified and directed. |
| 11 | M&L for water proofing treatment to roof surface with APP polymeric based water proofing membrane 3mm thick & weighing not less than 3.0 Kg / Sqm of approved make black finish consisting of a central core of high molecular high density polyethylene film (HMHDPF) & reinforced with non woven polyester matt of min 150 gm/sqm with a thermo fusible finish laid over a coat of hot blown bitumen of 85/25 grade conforming to IS 702 @ 1.2 kg/sqm over a coat of an bitumen primer conforming to IS-3384 @0.4 Ltr/Sqm over prepared roof surfaces, forcing overlap with a propane or a butane gas torch with a overlap of 75mm at sides & 100mm at ends & sealing including applying a coat of cold emulsion bituminous primer complete as per manufacturer's instructions complete all as specified and directed.Note :- 1. Water proofing treatment shall be got carried out by the OEM or their authorised applicator only. Contractor will submit MoU with the authorised applicator and shall be approved by GE before commencement of work. OEM shall provide warranty of 05 five years for the waterproofing work.2. Bitumen primer, bitumen and membrane shall be of same make / manufacturer. 3. The APP Membrane to be inserted in the parapet wall/wall by cutting chases of atleast 65mm X 50mm size& making good in CM 1:3. |
| 12 | Taking up or down 15mm bore steel tubing and connections incl cleaning for refixing or removal to store complete all as specified and directed |
| 13 | All as per item No. 12 above, but 20mm bore. |
| 14 | All as per item No. 12 above, but 25mm bore. |
| 15 | All as per item No. 12 above, but 40mm bore. |
| 16 | M&L 20mm CPVC pipes SDR 11 with all plain CPVC SDR 11, ISI marked and brass threated fittings (like elbow, Tee, MTA/BTA Adeptor,tank adeptor etc.) CPVC fittings and fixed complete to walls, ceiling or laid in floor complete all as specified and directed |
| 17 | All as per item No 16 above but 25mm dia. |
| 18 | All as per item No 16 above but 32mm dia. |
| 19 | S&F for 40 mm tubes, 'Medium grade' galvanised, ISI marked with all fitting and fixed complete to walls and ceilings or laid in floors. Complete all as specified and as directed. |
| 20 | M&L for Cutting chases, pinning in making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc. and cutting chases for concealed water tubing or concealed conduit wiring etc. and making good, cutting not exc 10 cm girth for inserting GI tubing / CPVC pipes in walls, floor etc and making good complete all as specified & directed by Engr in Charge. |
| 21 | Dismantling of PVC water storage tanks exc 250 & n.exc 500 ltrs capacity and removing from site complete all as specified and directed |
| 22 | S&F rotational moulded polythylene water storage tanks 500 Ltrs capacity,ISI marked triple layered (cylindrical vertical with closed up) hoisted and fixed in position incl tank cover complete all as specified and directed. |
| 23 | Dismantling of cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required, Internal dia of pipe 100mm complete all as specified and directed |
| 24 | Dismantling of cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required, Internal dia of pipe 75mm complete all as specified and directed |
| 25 | Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc, including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed. |
| 26 | S&F 100mm bore cast iron soil waste or vent pipes in any length with or without ears with lead joints laid in trenches or in floors/ walls complete all as specified and directed |
| 27 | S&F 75 mm bore cast iron soil waste or vent pipes in any length with or without ears with lead joints laid in trenches or in floors/ walls complete all as specified and directed |
| 28 | S&F 100 mm bore cast iron bends / Tee (any radius) diminishing pieces or tapers (larger bore to be measured) with oval access doors, with lead joints. Complete all aas spd and as directed. |
| 29 | S&F 75 mm bore cast iron bends / Tee (any radius) diminishing pieces or tapers (larger bore to be measured) with oval access doors , with lead joints complete all as specified and directed. |
| 30 | S&F 100mm bore Branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with lead joints & with parallel branches including oval access door complete all as specified and directed. |
| 31 | S&F CI Cowl for 100 mm bore of CI pipe. |
| 32 | S&F CI Cowl for 75 mm bore of CI pipe. |
| 33 | S&F of 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls and trenches complete all as specified and directed. |
| 34 | S & F bends 110mm dia PVC (SWR) bends complete all as specified and directed. |
| 35 | S&F 100 mm bore cast iron 'P' or 'S' traps fixed with lead joints complete all as specified and directed |
| 36 | S&F in repairs CI floor trap with grating including jointing to waste pipe in run lead with dia of outlet 75 mm including floor around to required depth and burning lead joints etc to facilitate dismantling old CI trap and making good complete all as specified and directed |
| 37 | S&F 100mm dia stack clamps out of 50 mm by 5 mm flat iron 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 100mm bore of pipe complete all as specified and as directed. |
| 38 | S&F 75mm dia stack clamps out of 50 mm by 5 mm flat iron 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 75 mm bore of pipe complete all as specified and as directed. |
| 39 | S&F in repairs 10 litres capacity PVC valveless syphonic action type low level flushing cistern complete with syphone handle lever PVC bend including connecting to WC and fixing on walls with bracket complete all as specified and as directed. |
| 40 | S&F in repair European vitreous china wash down water closet pan S / P Trap (excluding flushing cistern but including flush pipe and pvc seat cover white) complete all as specified and as direcfted by Engr in Charge. |
| 41 | S&F in repairs vitreous china wash hand basin (flat back or angle back type) white of size 550x400mm excluding taps, waste chain and plug and porcelain stopper including a pair of mild steel angle iron brackets of suitable size complete all as specified and as directed by Engr in Charge. |
| 42 | S&F in vitreous china wash hand basin (flat back or angle back type) white of size 450x300mm excluding taps, waste chain and plug and porcelain stopper including a pair of mild steel angle iron brackets of suitable size complete all as specified and as specified by Engr in Charge. |
| 43 | S&F sink made of stainless steel 1mm thick for kitchen with plugs, washers and waste including bedding in cement mortar to dwarf wall or including fixing cantilever, brackets and connecting union to pipe over all size 495 x 420 mm, bowl size 410 mm x 330 mm x 160mm complete all as specified and directed. |
| 44 | S&F mild steel framed work as in door or gates of angle or other sections, cooler stands, with gusset plates rails, braces, door / cupboard frame etc complete drilled for fixing of steel sheeting or other covering, doors etc to be prepared for hanging or sliding with and including either hooks and purpose made hinges or steel sheeting or other covering, running rails and guides) and hanging, fastening and fixing complete conforiming to Fe 290 Gde E-165 complete all as specified and directed. |
| 45 | Taking down wooden/steel chowkhats/door frame including shutter (without taking off shutter from frame) exc 1.5 Sqm and n.exc 4 Sqm each and removing to or from store complete all as specified and directed. |
| 46 | Taking down wooden/steel chowkhats/door frame including shutter (without taking off shutter) not exc.1.5 Sqm each and removing to or from store complete all as specified and directed. |
| 47 | Taking down shutter of any description exc 1.00 Sqm and not exc 2.00 Sqm complete all as specified and directed. |
| 48 | S&F outer frame 40mmx40mm with 1.3mm thickness, corner 45 degree cut & aluminum welded center mullion size 40mmx65mm also welded , fixed 5mm frosted glass EPDM rubber gasket with provision for fresh air fan, full system powder coating with pure polister coat of any shade install with SS screw rol plug pvc & silicone complete all as specified and directed. |
| 49 | S&F Outer frame 40mmx114mm with 1.3mm thickness ,corner 45 degree cut & aluminum welded center mullion size 40mmx65mm also welded, shutter size 40mmx60mm 1.3 thickness 45degree cut mechanically joint with 6mm alen key bolt clamp , 12mm SS 202 grade round bar at 100mm cc distance in middle 150mm cc distance for safety grill welded at both ends with 6mm SS 202 grade round bar as per site reqmt, the grill will be fixed in two portion, half lower portion grill will be open able/ lifted horizontally and fixed with hinges as per site reqmt, 5mm clear glass both side EPDM rubber gasket metal body hand lever type single point lock , aluminum kobra hinges 2 nos per shutter , 40x18mm 45 degree cut & welded mosquito net shutter with aluminum 24 gauge mosquito net ss 75mm long hinges & pvc magnet , full system powder coating with pure polister coat of any shade install with ss screw roll plug PVC & silicone. Drg No CEDZ/TD-316 Chief Engineer Delhi Zone |
| 50 | M&L for Outer frame 40mmx114mm with 1.3mm thickness ,corner 45 degree cut & aluminum welded center mullion size 40mmx65mm also welded, shutter size 40mmx60mm 1.3 thickness 45degree cut mechanically joint with 6mm alen key bolt clamp , 12mm SS 202 grade round bar at 100mm cc distance in middle 150mm cc distance for safety grill welded at both ends with 6mm ss 202 grade round bar, 5mm clear glass both side EPDM rubber gasket metal body hand lever type single point lock , aluminum kobra hinges 2 nos per shutter , 40x18mm 45 degree cut & welded mosquito net shutter with aluminum 24 gauge mosquito net SS 75mm long hinges & pvc magnet , full system powder coating with pure polister coat of any shade install with ss screw rol plug PVC & silicone. Drg No CEDZ/TD-316 Chief Engineer Delhi Zone |
| 51 | S&F brass chromium plated magic eye complete all as specified and directed. |
| 52 | M&L for 600x450mm beveled edge mirror of selected quality glass 5.5 mm thick mounted on and including 4 nos. hanging SS bolts including taking down old unserviceable looking mirror complete all as specified and directed. |
| 53 | M&L for Preparation of new or previously untreated surfaces of steel surface of any description not otherwise described over 10cm width or grith and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 54 | Complete removal of existing old treatment on surface of walls with mechanical grinder (machine) as per specification of manufacturer paints/OBDs. Complete all as specified and as directed. |
| 55 | M&L for a coat of alkali resistant primer including preperations of old surfaces of walls. Complete all as specified and directed. |
| 56 | M&L for applying two coats of oil bound distemper on old wall surface with roller brush over 1mm thick wall care putty. Complete all as specified and directed. |
| 57 | M&L for Complete removal of existing old treatment on surface of walls with mechanical grinder (machine) as per specification of manufacturer paints and preparing old plastered surfaces of wall and Finishing walls with Acrylic Smooth exterior paint of required shade @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) and 1mm thick wall care putty. Complete all as specified and directed. |
| 58 | M&L for two coats of oil bound distemper on old surfaces of ceiling incl preparation of old surfaces over one coat of alkali resistant primer & including 1mm thick wall care putty complete all as specified and as directed. |
| 59 | M&L for rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surfaces of walls finished fair and smooth without using extra cement even height in multistorey building. Complete all as specified and as directed |
| 60 | M&L for rendering 12mm thick in CM 1:6 on other than fair faces of brick work or concrete surfaces of walls finished fair and even without using extra cemet and in multistorey building. Complete all as specified and as directed. |
| 61 | M&L for 5mm thick rendering in cement mortar 1:3 finished fair and even surface without using extra cement on ceiling, chajja in multy storey building etc complete all as specified and as directed. |
| 62 | M&L for preparation of newly plastered surfaces of wall and apply two coat oil bond distemper over one coat of primer from the same manufacture including 1mm thick wall care putty. Complete all as specified and directed. |
| 63 | M&L for two coats of oil bound distemper including preparation of new plastered surfaces of ceiling over one coat of alkali resistant primer & including 1mm thick wall care putty complete all as specified and as directed. |
| 64 | M&L for preparation of newly plastered surfaces of wall and Finishing walls with Acrylic Smooth exterior paint of required shade, New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) including 1mm thick wall care putty. Complete all as specified and directed. |
| 65 | Taking down cement plaster, terrazzo dado in any thickness from brick or stone walls , ceiling surfaces etc. including raking out joints, hacking for key, scrubbing down with water etc including removal of rubbish,vegitation outside complex (MOD land), complete all as specified. |
| 66 | Supply only Integral waterproofing compound (ISI marked) |
| 67 | M&L for non skid colour ceramic vitrified tiles 400×400×7 to 8 mm thick thick (square/rectangular) area of each tiles exceeding 0.06Sqm but not exceeding 0.11Sqm in floors etc. with 4mm groove and epoxy filling as directed, set jointed in neat cement slurry & pointed in coloured cement to match and including 15mm thick screed bed in CM (1:6) complete all as specified and directed. |
| 68 | M&L for coloured glazed ceramic tiles of size 600X300X7 to 8 mm on vertical surfaces such as dado/skirting, set and jointed in neat cement slurry and pointed in white/ coloured cement, laid over and including cement screed bed 10mm thick in cement mortar 1:4, complete all as specified and directed. |
| 69 | M&L for joint free Non - skid coloured Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match to match and including 15mm thick screed bed in CM (1:6) complete all as specified and directed. |
| 70 | M&L for joint free Non - skid coloured Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match to match the existing ground conditions. Complete all as specified and directed by Engr in Charge. |
| 71 | Dismantling floor, hearth or wall tiling, any type of floor finish including cement mortar bedding of any thickness, removing serviceable tiles to store and rubbish off the premises all as specified and directed. |
| 72 | M&L for Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. including Brushing neat cement slurry with 3.0kg of cement per sq. metre complete all as specified & directed. |
| 73 | M&L for machine cut Kota stone slab 20 to 25 mm thick as in treads, risers, landings of staicase laid over cement screed base and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, making of bull nose laid over and including cement screed bed 20 mm thick in cement mortar 1:6 complete all as specified and directed. |
| 74 | S&F in repair aluminium anodised tubular towel rail 20mm dia, D type 60 cm long between flanges, complete all as specified and directed. |
| 75 | S&F in repair Glass Shelf of 8mm minimum thickness including CP railing with minimum 400mm length complete all as specified and directed by the Engineer-in-Charge. |
| 76 | S&F in repair stainless steel peg set of 6 peg complete all as specified and directed. |
| 77 | S&F in repairs Stainless Steel curtain rails with fixing brackets stops and rollers, inc Knobs etc. Complete all as specified and as directed by Engr in Charge. |
| 78 | S&F in repairs 15mm dia chromium plated bib tap, cast copper alloy with crutch or butterfly handle, screwed down, ISI marked screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. |
| 79 | S&F brass CP vertical mixe, ISI marked for mixing hot & cold water for wash hand basin screwed down for 15 mm bore iron pipe of ferrule complete all as specified and directed. |
| 80 | S&F CP wall mixer,ISI marked non telephonic type for mixing hot and cold water for shower screwed down for 15 mm brass iron pipe of ferrule of complete all as specified and directed. |
| 81 | Supply and fix Brass CP mixer, ISI marked swivel spout for mixing hot & cold water for Sink screwed down for 15mm bore iron pipe or ferrul of complete all as specified and directed. |
| 82 | S&F in repairs stop valve / Angle valve, ISI marked 15mm bore fancy type chromium plated, with long shank and cup (concealed type) complete all as specified and directed. |
| 83 | S&F in repairs 15mm bore stop valves / angle valves,ISI marked cast copper alloys, fancy type chromium plated, screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed. |
| 84 | S&F in repairs 20mm bore of Gun-metal, globe or gate valves,ISI marked with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed. |
| 85 | S&F in repairs PVC connection 450mm long with 2 Nos brass check nuts, suitable for 15mm bore complete all as specified and directed. |
| 86 | S&F in repairs PVC connection 600mm long with 2 Nos brass check nuts, suitable for 15mm bore complete all as specified and directed. |
| 87 | S&F in repair ball valve high pressure of PTMT with epoxy coated aluminum rod and high density polythene float and flynut complete, screwed for iron pipe or brass furrule size 25mm bore. (Min weight 210gms complete all as specified and directed) |
| 88 | S&F in repairs shower rose, chromium plated brass, fancy type, 125 mm with or without swivel joint, any size, including fixing to steel pipe or union, complete all as specified and directed. |
| 89 | Supply in repairs only CP waste coupling 32mm size with PVC waste pipe, plugs and washers for kitchen sink complete all as specified and directed. |
| 90 | S&F in repairs stainless steel kitchen plate rack made out of stainless steel sheets 1mm thick overall size 600mmx750mmx250mm including complete all as specificed and directed. |
| 91 | M&L for providing 40mm thick PCC 1:2:4 type B-1 using 20mm graded stone aggregate admixed with integral WPC complete all as specified. (Note: Supply only WPC shall be measured and paid saparately.) without using extra cement. |
| 92 | M&L for providing Cement concrete 1:5:10 in filling of sunken portion and sub base type E2 using 40mm graded aggregate. Complete all as specified and directed. |
| 93 | M&L for protection plaster 15mm thick on cement mortar 1:3 admixed with appropriate integral water proofing compound complete all as specified and directed.(Note : Supply only WPC shall be measured and paid separately) |
| 94 | M&L for two component glass fibre reinforced acrylic modified cementious comprising one coat of polymer modified cemetious slurry, embedding the glass fibrewhile the fist coat is wet, followed by second coat to achiee minimum dry thickness of 2 mm, complete all as specified and directed |
| 95 | S&F in repairs 50mm dia PVC Pipe including Elbow, Tee, Bends as per site requirements complete all as specified and directed. |
| 96 | M&L for providing 40mm dia GI pipe spout projecting at least 150mm beyond outer face of wall complete all as specified and directed. |
| 97 | M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 grade laid over 25mm thick sand cushion with grey cement and pigment complete all as specified and directed. (Note : Sand filling to be measured and paid seperately) |
| 98 | M&L for sand filling under floors for cushion bed to interlocking paver block all as specified and directed. |
| 99 | M&L for 100mm thick PCC 1:4:8 type D2 using 40mm graded stone aggregate as in sub base flooring complete all as specified and as directed by Engr in Charge. |
| 100 | S&F framed work such as grills, grating etc. with ends of bars shouldered and or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walkways, parapet railings on tubular form, framework of water tanks and similar works conforming to Fe290 Gde-E-165 complete all as specified and directed. |
| 101 | M&L for 18 to 20mm thick, granite (of any type) work (table rubbed and polished) in window-sills, cooking platforms and like in 15mm tihck cement mortar (1:6) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including made of half round Granite Corner complete all as specified and directed. |
| 102 | S&F FRP chajjas of 450mm wide suitable for various openings including fittings and fixtures upto 4 storey bldg complete all as specified and directed. |
| 103 | M&L for cement concrete 1:3:6 type C2 (using 40mm graded stone aggregate) as in plinth protection 75mm thick laid in bays and surfaces finished even and fair. Complete all as specified and as directed by Engr in Charge. |
| 104 | Demolition of RCC jalli any size and any position and providing and fixing glass reinforced concrete (G.R.C) jalli/panels in approved size pattern,design,thickness and colour of GRC Terra firma make or equivalent.Quart,fine silica sand,Alkali resistant glass fibre manufacture by NEG or equivalent, polymer manufactured by BASF or equivalent and UV resistant synthetic norganic pigment should be usedfor pigmentationmanufactured by Bayferrox(Germony) or equivalent. The material casting should be used for pigmentation manufactured by reckli or equivalent. The fixing of screen should be Dryfixing ie to be done with MS frame work with and including fixing arrangement in required shape including brackets, fasteners and pins etc complete all as specified and directed. |
| 105 | M&L Cement Concrete 1:2:4 type B-2 (40mm graded aggreate) 125mm thick as in tank staging , platforms etc finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed. |
| 106 | S&F Grating doom 100mm dia of SS with / without holes (Minimum weight 35gms). Complete all as specified and directed by Engg-in-Charge |
| 107 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size 50 x 75mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with meter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and directed by Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). → Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 108 | S&F Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of EngineerIn- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)complete all as specified and directed. |
| 109 | S&F Factory Made 18mm thick 100% Solid WPC ( Wood polymer Composite ) Laminated Board of required size comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade ), Calcium Carbonate and natural fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with having minimum density not less than 650 kg/cbm having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compissive of 50 N/mm2 , Modulus of elasticity 850N/mm2 and esistance of spread of flame of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof and Fire Retardant. WPC to be Laminated with PVC foil of minimum 14 microns thick of approved design pasted on both faces of shutter and fixinng stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws. Complete all as specified and directed by Engineer -In-Charge, Material test certificate and authentication should be compulsory provided by the manufacturing company : For WC/Bathroom/Toilet/Kitchen and Cabinets. |
| 110 | S&F continous (piano hinges, mild steel bright finish or electro galvanized width of flap 30mm when open complete all as specified. |
| 111 | S&F of stainless steel handles 100 mm size for kitchen cabinet shutters and bed room cub boards complete all as per specified and directed.Make: ( Hettich, Ebco, Prime, Inox ) |
| 112 | S&F 100mm size hasp and stable safety type aluminium anodised with mild steel hinge pin including bolt to hinge palte and fixed screws complete all as specified and directed. |
| 113 | Supply and fixing 30mm thick FACTORY MADE WIRE MESH SOLID WPC DOOR SHUTTER consisting of density 650 kg/cbm manufactured by an ISO-9001-2015 certified company. Door to be panelled with SS mosquito and XTN aluminium mesh for additional strength and safety purpose (confirming as per IS 4020). The door should be water proof, termite proof, fire retardant and having screw holding capacity. Door to be fixed to frame with 3 nos. SS butt hinges size 100mmx25mmx2mm and 32mm long steel screws drilled suitable to pass through other hardwares should be fixed with 19x6mm size steel screws, etc. complete all as specified and directed.Note: MTC and Screw Out Test will be provided by Contractor |
| 114 | S&F Providing and fixing factory made single extruded WPC(Wood Polymer Composite) solid decorative type flush door shutter of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as specified and directed by Engineer-in-Charge. |
| 115 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screwshaving minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete all as specified and directed by Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).Note: For WPC solid door/window frames,minus 5mm tolerance indimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 116 | S&F Factory Made single extruded WPC (Wood Polymer Composite) Solid door/window/Ceosetory windows & other frames/ chowkat of size 65 x 125 mm comprising of virgin PVC polymer of K value 50-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non-toxic additives (max toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face & 1100 N Edge), min compressive strength of 58N/sqmm and resistance to flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed with MS Holdfast/ lugs/SS dash fasteners of required dia and length complete as specified and directed by Engineer-in-charge. Note: For WPC solid door/windows frames,minus 5mm tolerance in dimension i.e depth and width of profile dimension on plus side shall be acceptable but no extra payment on this account shall be made. |
| 117 | S&F stainless steel AISI 304 grade floor door stopper with hard drawn steel spring 140mm long complete all as specified and directed. |
| 118 | S&F SS barrel tower bolt extruded section 200mm long and fixed with SS Screws (ISI Marked) |
| 119 | S&F SS barrel tower bolt extruded section 150mm long and fixed with SS Screws (ISI Marked) |
| 120 | S&F 300mm extruded section SS sliding door bolt with hasp and staple and fixing bolt and nut (ISI Marked) |
| 121 | S&F 150mm extruded SS handle fabricated type and fixed with SS Screws (ISI Marked) |
| 122 | S&F SS butt hinges medium weight 100mm size fixed with SS screws (ISI Marked) |
| 123 | S&F SS butt hinges medium weight 75mm size fixed with SS screws (ISI Marked) |
| 124 | M&L for Providing & injecting chemical for post construction ATT along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc in a portion with cement mortar 1:2 to match the existing apron complete all as specified and directed. |
| 125 | M&L for Post Construction anti termiteTreatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same complete all as specified and directed. |
| 126 | M & L for Post Construction anti-termite Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floors complete all as specified and directed. |
| 127 | S&F 25mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides as shutter of cupboard etc. Complete all as specified and directed. |
| 128 | M&L for Preparation of new or previously untreated surfaces of wood or wooden base surface of any description not otherwise described over 10cm width or grith and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 129 | All as per item No. 128 above but one coat of paint on old steel surfaces. |
| 130 | Dismantling of any type of MS works like railings, grill, cooler stands etc. Complete all as specified and as directed by Engr in charge. |
| 131 | STRUCTURAL REPAIR ITEMSExcavation over areas not exceeding 1.5m deep and getting out in any type of soils complete all as specifed and as directed. |
| 132 | Returning, filling in, including spreading, levelling, watering and well ramming in layers n exc 25 cm in soft/loose soil complete all as specified and directed. |
| 133 | Removing excavated materials exc 50m and n exc 500 m and depositing where directed, complete all as specified and directed. |
| 134 | M&L for demolition of Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) , removal of debries beyond MoD lands. Complete all as specified and as directed. |
| 135 | Demolition of reinforced cement concrete in Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work etc. (Reinforcement cut as required to facilitate demolition), removal of debries beyond MoD lands. Complete all as specified and as directed. |
| 136 | M&L for removing loose and broken concrete by chiselling /picking etc upto a depth of 80 to 100 mm from columns, beams, slabs and similar structural members cutting edges cleaning the dismantled portion with wire brushes etc to remove dust, dirt and other foreign particles etc and washing with clean water with pressure and removal of debries beyond MoD lands. Complete all as specified and directed by Engineer-in-Charge. |
| 137 | Cleaning of reinforcement from rust from the reinforcing bars to give it a total rust free steel surface by using alkaline chemical rust remover of approved make with paint brush and removing loose particles after 24 hours of its application with wire brush and thoroughly washing with water and allowing it to dry, all complete as specified and directed by Engineer-In-Charge |
| 138 | M&L for applying one coat of anti corrossive primer @ 0.25 Lit/Sqm for the steel area to exposed old and new reinforcement to the full circumfrance and length of bars to form unbroken 40 Micron thick film all as specified and directed by Engr-in-Charge. |
| 139 | M&L for applying one coat epoxy bonding agent @ 2.6 sqm/lit or as per manufactures instruction to old concrete surfaces all as specified and directed by Engineer-in-Charge to surfaces of columns, beams and similar structural members complete all as specified and directed. |
| 140 | M&L for drilling holes in slabs/wall/column/beams for anchor steel reinforcement incl washing with water, and all as specified and directed by Engineer-in-Charge. |
| 141 | M&L for drilling holes in slabs/wall/column/beams for anchor steel reinforcement incl washing with water, inserting specified chemical in the holes and all as specified and directed by Engineer-in-Charge. |
| 142 | M&L mild steel TMT bars 10 mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and directed. |
| 143 | M&L Mild steel TMT bars 6-8mm dia. And over upto & including 10mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips as in stirrups binders and spacers complete all as specified and directed. |
| 144 | M&L for non shrink, cementitous micro concrete mixed with 12.5 graded stone aggregate using Renderoc RG or equivalent by weight (18 Kg Aggregate :25 Kg Renderoc RG) respectively (as per manufatures instruction) laid in average thickness 80 to 100 mm in surface complete all as specified and as directed by Engineer-in-Charge. (Mixing With 30% 6 to10mm Aggregate) |
| 145 | M&L for PCC type D-2 (1:4:8) filling & mass conc. |
| 146 | M&L for shuttering of Fdn footing, bases of columns, plinth beams etc. |
| 147 | M&L for shuttering of Floor or roof beams/lintel beams, lintels, cantilevers, shelves etc. |
| 148 | M&L for shuttering of Columns, posts, pillars etc. |
| 149 | M&L for Reinforced cement concrete in footings, fdn beams, plinth beam/band, bases of columns |
| 150 | M&L for Reinforced cement concrete in Slabs , landings, balconies, canopies, shelves |
| 151 | M&L for Reinforced cement concrete in Beams, cantilevers, lintels over 1.5 m span |
| 152 | M&L for application of high build Premix structure grade repair mortar Up-to 40mm thick in four layers surfaces over a coat of bonding agent complete all as specified and directed. Only premix repair mortar to be used. |
| 153 | Hard drawn steel wire fabric cut to lengths, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9mm in dia supplied and fixed in reinforcemnt (Weight per square metre Exc. 4 kg) complete all as specified and directed. |
| 154 | Note: (i) Complete Structural Repair work shall be got carried out by the manufacturer or their authorised applicator only. Contractor will submit MoU with the authorised applicator and shall be approved by GE before commencement of work. (ii) Contactor shall submit warranty for 10 years for the structural repair from OEM/Authorised Applicator. (iii) After execution of structural rehabilitation work, holistic testing of all structural member repaired will be got done by the contractor through IIT/NIT and structural strength achieved after repair along with structural safety from IIT/NIT will be submited by the contractor. The cost of the same shall be deemed to be included in rates quoted by the contractor. |
| 155 | INTERNAL ELECTRIFICATIONTaking down carefully copper/aluminium any type of point wiring (light/fan/socket /power) complete (fittings such as switches, ceiling roses, holders, sockets,regulators light fittings) and removal from site and making good the disturbed surfaces of (wall/floors/ceiling etc) complete all as specfied & directed. |
| 156 | Material & Labour for point wiring with 1.5 sqmm (nominal size) single core, 1100 Volts grade, multi stranded, PVC insulated, unsheathed FRLSH electrolytic copper conductor cable ISI marked conforming to IS 694:2010 with and including continuous earth wire of size 1.5 sqmm (nominal size) single core, 1100 Volts grade, multi stranded, PVC insulated, unsheathed, FRLSH electrolytic copper conductor cable and connected to earth dolly, colour coded as per IS 11353:1985 drawn through an including concealed medium grade, PVC conduit of 20 mm dia (Nominal bore) or higher, minimum wall thickness 1.6 mm conforming to IS 9537(Part 3):1983 for conduits complete with and including all conduit accessories (conforming to IS 3419:1988 for conduit accessories) and factory made not less than 1.2 mm thick sunken modular flush sheet galvanised metal enclosure having zinc coating not less than 120 GSM conforming to IS 14772:2000 having bottom, side and back-wall knockouts for conduit entry from any direction, suitable modular cover plate with frame and making good of disturbed surfaces of wall/ceiling/floor etc complete all as specified in IS 732:2019 and directed by Engineer-in-Charge at site for the following :- |
| 157 | (a) One light/fan/bell point controlled by one way switch 5 amps. |
| 158 | (b) One two way point controlled by 2 way switch 5 amps. |
| 159 | Material & Labour for point wiring with 2.5 sqmm (nominal size) single core, 1100 Volts grade, multi stranded, PVC insulated, unsheathed FRLSH electrolytic copper conductor cable conforming to IS 694:2010 with and including continuous earth wire of size 2.5 sqmm (nominal size) single core, 1100 Volts grade, multi stranded, PVC insulated, unsheathed, FRLSH electrolytic copper conductor cable and connected to earth dolly, colour coded as per IS 11353:1985 drawn through an including concealed medium grade, PVC conduit of 20 mm dia (Nominal bore) or higher, minimum wall thickness 1.6 mm conforming to IS 9537(Part 3):1983 for conduits complete with and including all conduit accessories (conforming to IS 3419:1988 for conduit accessories) and factory made not less than 1.2 mm thick sunken modular flush sheet galvanised metal enclosure having zinc coating not less than 120 GSM conforming to IS 14772:2000 having bottom, side and back-wall knockouts for conduit entry from any direction, suitable modular cover plate with frame and making good of disturbed surfaces of wall/ceiling/floor etc complete all as specified in IS 732:2019 and directed by Engineer-in-Charge at site for the following :- |
| 160 | (a) One 3 pin 5 Amps socket outlet point controlled by one way switch on independent board. |
| 161 | (b) One 3 pin 5 Amps socket outlet point controlled by one way switch on same board. |
| 162 | (c) One 3 pin socket outlet point 5/15A independent board |
| 163 | Material & Labour for point wiring with 4.0 sqmm (nominal size) single core, 1100 Volts grade, multi stranded, PVC insulated, unsheathed FRLSH electrolytic copper conductor cable conforming to IS 694:2010 with and including continuous earth wire of size 4.0 sqmm (nominal size) single core, 1100 Volts grade, multi stranded, PVC insulated, unsheathed, FRLSH electrolytic copper conductor cable and connected to earth dolly, colour coded as per IS 11353:1985 drawn through an including concealed medium grade, PVC conduit of 20 mm dia (Nominal bore) or higher, minimum wall thickness 1.6 mm conforming to IS 9537(Part 3):1983 for conduits complete with and including all conduit accessories (conforming to IS 3419:1988 for conduit accessories) and factory made not less than 1.2 mm thick sunken modular flush sheet galvanised metal enclosure having zinc coating not less than 120 GSM conforming to IS 14772:2000 having bottom, side and back-wall knockouts for conduit entry from any direction for one 3 pin AC Box outlet 20 Amps concealed and making good of disturbed surfaces of wall/ceiling/floor etc complete all as specified in IS 732:2019 and directed by Engineer-in-Charge. (For AC point) |
| 164 | Supply and fix switch modular 1 way 6 Amps,1 module, ISI marked complete all as specified and as directed. |
| 165 | Supply and fix switch modular 1 way 16 Amps,1 module, ISI marked complete all as specified and as directed. |
| 166 | Supply and fix modular socket outlet 6 A. 2/3 pin, combined 2 module, ISI marked complete all as specified and directed. |
| 167 | Supply and fix modular socket 16 A, 2/3 pin, combined 2 module, ISI marked complete all as specified and directed. |
| 168 | Supply and fix switch modular 2 way 6 Amps,1 module, ISI marked complete all as specified and as directed. |
| 169 | Supply and fix modular bell push 6 Amp 1 module, ISI marked complete all as specified and directed. |
| 170 | S&F of electric bell ding dong AC, 230 volts, single pole with brass screw and cup washers complete all as specified and directed. |
| 171 | S&F LED B22 1X12 W, 220V, AC LED Lamp decorative wall mounting light fitting fixture made up of aluminium body including LED 12 watt with system level efficacy of the luminaire is >= 100 lm/W, color temperature-6500K, including connecting up with necessary PVC sheathed 3 core 1.5 Sqmm copper conductor flexible wire fixed complete all as specified and directed. |
| 172 | S&F of lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings with connections complete all as specified and directed. |
| 173 | S&F LED Lamp of wattage 09 Watt, System Luminous Efficacy ≥ 90 lm/W with Power Factor ≥ 0.90 & CRI:80,protection against high voltage upto 360V,B-22, 230 Volts,50 Hz, CCT:6500K complete all as specified and directed. |
| 174 | Taking down sub main wiring off sizes. |
| 175 | Supply, laying and drawing submain wiring in and including 20 mm dia concealed PVC rigid conduits ISI marked including cutting of chases for laying conduit making good the surfaces as per existing surfaces or as directed on walls 02 runs of IC x 6.00 sqmm (Main Cable and neutral) and one run of IC x 6.0 sqmm (as earth wire) of multistranded copper conductor PVC insulated, FRLSH, unsheathed cables of 1100 Volts grade conforming to IS 694:2010 complete including taking down existing old wire all as specified and directed. Note :- Two runs of IC x 6.00 sqmm (Phase wire and neutral ) and one run of IC x 6.00 sqmm (as earth wire) will be measured as one unit length. |
| 176 | Taking down ceiling fan, sealing cable end, dismantling blades and removing fan and blades and deposit to MES store yard for refixing complete all as specified and directed. |
| 177 | Hanging only ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan all as specified and directed. |
| 178 | S&F of 10 watts bulkhead fitting with powder coated die cast aluminium housing with glass/ non yellowing polycarbonate cover, IP-65 Protection, System Luminous Efficacy ≥ 90 lm/W, Power Factor ≥ 0.90, CCT: 3000K-6500K, including connecting up with necessary PVC sheathed 3 core 1.5 Sqmm copper conductor flexible wire fixed complete all as specified and directed. |
| 179 | S&F of factory made epoxy polyester powder coated distribution board SP & N 12 way fabricated from minimum 1.6 mm thick CRCA sheet with metal double door (IP-43, IK 9 protection) fixed flush to wall and suitable for universal mounting and including 100 Amps copper bus bar, Neutral bar, standard DIN rail, earth bar and cable ties for cable management, top and bottom removable gland plates with knockouts and suitable for one DP MCB as incomer and 10 SP MCBs as outgoings complete all as specified and conforming to IEC 61439-3 including taking down old DBs all as specified and directed.NOTE :-(a) MCBs shall be measured and paid separately.(b) All cables terminating into MCBs shall be connected by using suitable copper lugs/thimbles/sleeves and its cost shall be deemed to be included under respective item of Sch. |
| 180 | S&F of factory made epoxy polyester powder coated distribution board TP & N 4 way (VTPN MCCB DB) with metal double door (IP-43 & IK 9 protection) fabricated from minimum 1.6 mm thick CRCA sheet and fixed on wall and suitable for universal mounting and including 100 Amps copper bus bar, Neutral bar, standard DIN rail, earth bar and cable ties for cable management, top and bottom removable gland plates with provn for 125 Amps, 4 pole MCCB and ELM as incommer and 12 SP MCBs outgoings including blank spacer for blank space complete all as specified and conforming to IEC 61439-3 including taking down old DBs complete all as specified and directed.NOTE :-(a) MCBs/MCCBs shall be measured and paid separately.(b) All cables terminating into MCBs shall be connected by using suitable copper lugs/thimbles/sleeves and its cost shall be deemed to be included under respective item of Sch. |
| 181 | S&F of MCCB 125 Amp, 4 pole, 16 KA breaking capacity at 415 V, 50 Hz conforming to IEC 60947-2 with fixed thermal magnetic release complete all as specified directed. |
| 182 | S&F of single pole MCB 40 Amps, 240 v, 50 Hz AC made from moulded self-extinguishing thermostat plastic and suitable for ‘B’ curve, 10 KA breaking capacity conforming to IEC 60898-1:2002 complete all as specified and directed. |
| 183 | S&F of single pole MCB 6 to 32 Amps, 240 v, 50 Hz AC made from moulded self-extinguishing thermostat plastic and suitable for ‘B’ curve, 10 KA breaking capacity conforming to IEC 60898-1:2002 complete all as specified and directed. |
| 184 | Taking down & refixing of MCB SP 6 to 32 Amps complete all as specified and directed. |
| 185 | S&F of SPN MCB 40 Amps, 240V, 50 Hz AC made from moulded self-extinguishing thermostat plastic and suitable for ‘B’ curve, 10KA breaking capacity conforming to IEC 60898-1:2002 complete all as specified and directed. |
| 186 | S&F surface/wall mounting LED batten luminaire with following specifications :-(a) System Power : 20 W(b) Length : 4ft(c) Housing : Epoxy powder coated white extruded aluminium channel(d) Diffuser : Milky White Polycarbonate(e) Rated Voltage : 240V(f) Safe Operating Voltage : 140V to 270V(g) Rated Frequency : 50Hz(h) Power Factor : ≥ 0.95(j) THD : ≤ 10(k) Operating Temp : - 10 deg C to + 45 deg C(l) Lumen Efficacy of LED : ≥ 120 Lm/W(m) System Luminous Efficacy : ≥ 100 Lm/W(n) CRI : ≥ 80(o) CCT : 5700K(p) Driver : Integral SMPS based constant current type with short circuit, surge voltage protection upto 2.5 KV.(q) IP rating : 20(r) IK rating : 03(s) Average LED life : 50000 Hrs |
| 187 | Taking down & refixing of LED tube light 4 feet,20 watt including all connection upto ceiling rose complete all as specified and directed. |
| 188 | S&F surface/wall mounting LED batten luminaire with following specifications :-(a) System Power : 10 W(b) Length : 2ft(c) Housing : Epoxy powder coated white extruded aluminium channel(d) Diffuser : Milky White Polycarbonate(e) Rated Voltage : 240V(f) Safe Operating Voltage : 140V to 270V(g) Rated Frequency : 50Hz(h) Power Factor : ≥ 0.95(j) THD : ≤ 10(k) Operating Temp : - 10 deg C to + 45 deg C(l) Lumen Efficacy of LED : ≥ 120 Lm/W(m) System Luminous Efficacy : ≥ 100 Lm/W(n) CRI : ≥ 80(o) CCT : 5700K(p) Driver : Integral SMPS based constant current type with short circuit, surge voltage protection upto 2.5 KV.(q) IP rating : 20(r) IK rating : 03(s) Average LED life : 50000 Hrs |
| 189 | Taking down existing exhaust fan, keeping in safe custody and refixing the same after completion of work complete all as specified and directed. |
| 190 | S&F of Fresh Air Fan made of sturdy Engineering plastic complete with louver shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250 mm sweep, single phase,including cutting of holes in wall/windows for fixing the fresh air fan complete all as specified and directed. |
| 191 | S&F in replacement LED Building security light fitting complete with mounting bracket made out of light grade GI pipe 40mm bore 1.20 mtr long bend to shape including 02 Nos of 40x5mm FI clamps with GI bolt, nut, washer and 3-core copper cable connection from ceiling rose to light fitting. Specification of light fitting are as under :-(a) System Power : 35 W(b) Housing : Pressure die cast aluminium alloy having separate optical & control gear compartment, top opening, polyster powder coated after phosphochromate treatment(c) Optics : Polycarbonate UV stabilised with integrated lens(d) Light source : SMD LED module mounted on MCPCB(e) Rated Voltage : 240V(f) Safe Operating Voltage : 140V to 270V(g) Rated Frequency : 50Hz(h) Power Factor : ≥ 0.95(j) THD : ≤ 10(k) Operating Temp : - 10 deg C to + 50 deg C(l) Lumen Efficacy of LED : ≥ 140 Lm/W(m) System Luminous Efficacy : ≥ 100 Lm/W(n) CCT : 5700K(o) Driver : In built SMPS based constant current type with protection for output open /short circuit, phase to phase, over voltage & surge voltage upto 10 KV.(p) IP rating : 66(q) IK rating : 07 |
| 192 | S&F ceiling rose 3 phase/PVC/polycarbonate isolated body complete all as specified and directed. |
| 193 | S&F of modular AC Box with 20 Amp SP mini MCB, plastic enclosure & unbreakable heavy duty ISI mark plug top complete set dully concealed in wall complete all as specified & directed. |
| 194 | Taking down existing geysers, transporting & depositing to MES yard and refixing after completion of work complete all as specified and directed. |
| 195 | S & F water heater storage type Geyser vertical type with suitable size of fastner and inner tank material of superior glass lined tank and outer body material of ABS with high pressure with standing enabling (up to 8 bar pressure) capacity including provision and connecting up of SS braided pipe of size 15mmx600mm long with adopter for inlet and outlet water connection suitable for hot and cold water having adjustable knob for temperature control and inner tank should be glass lined coated, capacity 25 Ltrs, having heating element 2 KW and BEE 5 star rated, suitable for 230 volt, 50 Hz electric supply complete all as specified and directed . |
| 196 | M&L in replacement of earthing complete with galvanised steel earth plate 600X600X6 mm thick buried directly in ground (earth pit not les than 2.25 M deep below GL with top edge of plate not less than 1.50 m below GL) connected with GI earth lead wire 4.0 mm as earthing leads by means of bolts, nuts, check nuts and washers all joints as shown on drawings and including excavation, earth work. GI pipe light grade 15 mm bore for protection of GI earth wire from earth electrode to and including the earth test point, supplying and laying charcoal dust, common salt PCC (1:2:4) type B1 chamber and MS angle iron frame of 40mmx40mm x3 mmand RCC cover 40 mm thick (1:2:4) type B1 using 20 mm graded stone aggregate reinforced with 8 mm dia TMT bars @ 75 mm C/C both ways with MS handle 12 mm dia, PGI funnel and wire mesh, 20 mm dia GI pipe light grade for watering all as shown in electrical plate No 3 of SSR Part -I and conected to earth test point including testing complete all as secified and directed at site. |
| 197 | MCCB 4 Pole, 415 V,50 HZ, Adjustable type, 160 Amps with breaking capacity 36 KA conforming to IEC 60947-2 with fixed thermal magnetic release complete all as specified directed. |
| 198 | S & F 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor copper wound, class of insulation : B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.50, Air delivery minimum 220 CMM, 350 RPM (tolerance as per IS 374:2019), THD less than 10%, remote unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC supply, earthing etc. complete as required including connecting up with twin core flat flexible copper conductor cable of suitable size with connector block to ceiling rose complete all as specified and directed. |
| 199 | S&F Modular ceiling fan regulator, step type for BLDC ceiling fan 1 or 2 module complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 07, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 05, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 20 daysSep 07, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 22 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender