Tender For special Repair Of 02 X Soakage Pit At Or Living Of 336 Med Regt And special Repair To Internal Wiring, Sub Main Wiring, Mcb Dbs And Lighting And Fixtures In Jco Living Bldg No T-99 & T-100 Of 108 Med Regt At Nurla Mil Stn Under Age (I) Nim
Tender Value
9.71 Lakhs
Estimated cost
Bid Submission
25 Aug 2026
0 days left
EMD
20000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Leh → Ladakh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repair Of 02 X Soakage Pit At Or Living Of 336 Med Regt And special Repair To Internal Wiring, Sub Main Wiring, Mcb Dbs And Lighting And Fixtures In Jco Living Bldg No T-99 & T-100 Of 108 Med Regt At Nurla Mil Stn Under Age (I) Nimu
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of stone/boulders masonry, laid dry complete all as specified and directed by Engr-in charge. |
| 2 | Demolition of stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed by Engr-in charge. |
| 3 | M&L for stone masonry Walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:4, complete all as specified. |
| 4 | M&L for stone masonry Walling of random rubble, uncoursed, well bonded, and solidly heartd laid dry as directed and as specified. |
| 5 | Demolition of Reinforced Cement Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) (reinforcement cut as required to facilitate demolition) complete all as specified and directed by Engr-in charge. |
| 6 | Use & waste formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick with flat rough finished surfaces of concrete, complete all as specifed and directed by Engr-in-charge. |
| 7 | M&L for RCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in slabs supported on walls, beams, and columns in floors, roofs complete all as specified and directed by Engr-in-charge. |
| 8 | Demolition of Cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed by Engr-in-charge |
| 9 | M&L for cement concrete 1:4:8 type D2 (using 40mm graded crushed stone aggregate) in foundation, filling and mass concrete complete all as specified and directed by Engr-in-charge. |
| 10 | M&L for Precast reinforced cement concrete, type B-1, 1:2:4 (Using 20mm graded crushed stone aggregate) as in manhole cover set in cement mortar 1:4, compete all as specified and directed. |
| 11 | S&F TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engr-in charge. |
| 12 | Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar of internal dia 75-100mm incl any earth work and demolition of PCC complete all as specified and directed. |
| 13 | S&F PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or floor of 110mm bore pipe complete all as specified and directed by Engr-in-charge |
| 14 | S&F for 110 mm bore PVC (SWR) bends any radius ® complete all as specified and directed by Engr-in charge. |
| 15 | S&F PVC (SWR) Vent cowl of 110mm bore, complete all as specified as directed. |
| 16 | S&F PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or floor of 75mm bore pipe complete all as specified and directed by Engr-in-charge |
| 17 | S&F PVC (SWR) floor trap of 75mm plain with grating including jointing with solvent cement complete all as specified and directed by Engr-in charge. |
| 18 | M&L for 100mm thick cement concrete 1:3:6 type C2 bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested; complete all as specified and directed by Engr-in charge. |
| 19 | S&F for 110 mm bore PVC (SWR) branch piece, double (double Y) equal or unequal complete all as specified and directed by Engr-in charge. |
| 20 | S&F for 110 mm bore PVC (SWR) branch piece, single (single Y) equal or unequal complete all as specified and directed by Engr-in charge. |
| 21 | Demolition of precast concrete block walling masonry, built in cement mortar complete all as specified and directed by Engr-in charge. |
| 22 | M&L for Pre-cast cement concrete block masonry in cement concrete 1:3:6 type C1(using 20mm graded aggregate) with solid blocks, exc. 10 cm in width and setting in mortar 1:4 complete all as specified and directed by Engr-in charge. |
| 23 | M&L for Rendering 10mm thick on fair faces of concrete block masonry surfaces in cement mortar (1:6) complete all as specified and directed by Engr-in charge. |
| 24 | Taking down carefully aluminium/Copper point wiring light, fan socket or power complete fitting such as switches, ceiling rose, fan regulator, socket including light fitting etc complete with /PVC /MS conduit and T/W battern / casing caping and all as specified and as directed by Engineer-in-Charge. |
| 25 | Taking out old unsv underground cable of any size/make/ type etc from excavted tranches/ on pole passing through pipes etc from different locations complete all as specified and directed by the engr in charge. |
| 26 | Supply and fixing 1100 Volts grade heavy duty cable PVC insulated aluminimum conductor of size 16 Sq mm twin core, served with inner sheathing of PVC tape and overall PVC sheathed in service connections, flat or circular all as specified and directed by Engineer-in-Charge . |
| 27 | M&L for point wiring with PVC FRLS insulated single core cable of stranded copper conductors of size 1.5 sqmm, 1100 volt grade drawn in and including rigid PVC casing caping accessories lain on wall/ceiling surface and fixed with PVC saddles and back-plate and GI screws, including PVC insulated single core cable of stranded copper conductor of size 1.5 sqmm as earth continuous wire connected to common earth and PVC Board for housing like switches, sockets, fan regulators etc all as directed by Engineer-in-Charge for following :-(a) One light point/one fan point controlled by one switch |
| 28 | M&L for point wiring with PVC FRLS insulated single core cable of stranded copper conductors of size 1.5 sqmm, 1100 volt grade drawn in and including rigid PVC casing caping accessories lain on wall/ceiling surface and fixed with PVC saddles and back-plate and GI screws, including PVC insulated single core cable of stranded copper conductor of size 1.5 sqmm as earth continuous wire connected to common earth and PVC Board for housing like switches, sockets, fan regulators etc all as directed by Engineer-in-Charge for following :-(b) One 3 pin 5 amps socket outlet independent with cables 2.5 sqmm size complete all as specified and directed by Engr in Charge. |
| 29 | M&L for point wiring with PVC FRLS insulated single core cable of stranded copper conductors of size 1.5 sqmm, 1100 volt grade drawn in and including rigid PVC casing caping accessories lain on wall/ceiling surface and fixed with PVC saddles and back-plate and GI screws, including PVC insulated single core cable of stranded copper conductor of size 1.5 sqmm as earth continuous wire connected to common earth and PVC Board for housing like switches, sockets, fan regulators etc all as directed by Engineer-in-Charge for following :-(c) One 3 pin 5 Amp socket outlet on same board complete all as specified and directed by Engr in Charge. |
| 30 | All same as per item No 28 above but with conductor of size 4 sqmm (Nominal area) for one 3 pin socket outlet 15 Amps on independent board complete and earth continuity wire with 4 sqmm PVC insulated stranded copper conductor Cable complete all as specified and directed by Engr in Charge. |
| 31 | S&F Socket 2 in 1, 5 pin 5 Amp flush type complete all as specified and directed by Engr In Charge. |
| 32 | S&F Switch piano flush type 5 Amp, single pole, one way complete all as specified and directed by Engr in Charge. |
| 33 | S&f Switch socket combination 2 in 1, 3 pin, 5 Amp flush type complete all as specified and directed by Engr in Charge . |
| 34 | S&F Switch Socket Combination 2 in 1, 3 pin, 15/16 amp flush type Universal complete all as specified and directed by Engr in Charge . |
| 35 | M&L for ceiling rose surface Bakelite 65x50mm two to three terminal complete all as specified and as directed by Engr-in-Charge. |
| 36 | S & F LED light fitting 1x9W/1X10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size all as specified and directed by Engr in Charge. |
| 37 | S&F basic all purpose surface and wall mounted LED batten with polycarbonate housing and integreted electronic driver of cap 10 watt, 2 feet long, with all accessories complete all as per specified and as directed by Engr-in-Charge.(Havells Cat Pt No. - LHEXACP7IN1W010 or equivalent in Philips/Crompton) complete all as specified and directed by Engr in Charge. |
| 38 | S&F basic all purpose surface and wall mounted LED batten with polycarbonate housing and integreted electronic driver of cap 20 watt, 4 feet long, with all accessories complete all as per specified and as directed by Engr-in-Charge.(Havells Cat Pt No. - LHEXAXPNIN1W020 or equivalent in Philips/Crompton) complete all as specified and directed by Engr in Charge. |
| 39 | S&F basic all purpose surface and wall mounted LED Decorative, wall mounting, brushed nickel finish fixture with Opal Glass diffuser suitable with 9 W LED lamp B22 base. light with polycarbonate housing and integreted electronic driver of , with all accessories complete all as per specified and as directed by Engr-in-Charge.(Havells Cat Pt No. - LHEXAXPNIN1W020 or equivalent in Philips/Crompton) complete all as specified and directed by Engr in Charge. |
| 40 | S&F in repair sheet metal powder coated versatile Double door SPN distribution board, 12 way suitable for MCB's fitted with copper bus bar rated 200amps, neutral link , earth bar and din rail suitable for use on 240 Volt, 50Hz all as directed by Engr in Charge. |
| 41 | M&L in repair for MCB SPN 63 Amp, 240V with 10KA breaking capacity of 'C' series in distribution boards all as specified and directed. |
| 42 | S&F in repair to MCB SP 6-32 Amp with 10KA breaking capacity of 'C' series in distribution boards with all accessories complete all as per specified and as directed by Engr-in-Charge. |
| 43 | Dismantling and Taking down old u/s street / building sequrity Light fittings from poles, flood lights, post top lantern lights and garden lights for replacement with LED fittings all as specified and as directed by Engr in Charge. |
| 44 | Supply and fix LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete Specified and directed by Engr in charge. |
| 45 | Supply and fix in repair electric water heater,storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessoriessuch as safety valve, thermostate,NRV, connection piece etc. complete Specified and directed by Engr in charge. |
| 46 | M&L for GI bracket 1.5 mtr long made out of GI pipe 40mm dia bend to suitable radius incl clamps nuts bolts washers incl painting with aluminum paint etc complete all as specified and directed by Engr in charge. |
| 47 | Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz RPM 1200, Copper winding of sweep 250mm sweep with, blades, and frame and louvers all as per specified and as directed by Engr-in-Charge. |
| 48 | S&F in repair Air termination, single pointed, copper rod 12mm dia and 300mm long different locations / Bldg complete all as specified and directed by the engr in charge. |
| 49 | S&F in repair Test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 nos. 8mm dia 25mm long hex. head screw complete all as specified and directed by the engr in charge. |
| 50 | S&F in repair Galvanised earth lead wire 4.0mm dia for roof conductors and down conductors above ground complete all as specified and directed by the engr in charge. |
| 51 | Supply and fix in repair laying 32 mm light grade GI Tubes in trenches/on wall/ poles/ structures as in repairs GI tubeing light grade for road crossing/ for cable protection / fixing of pigmi lights etc, of the folling size including necessary provision for cable / Strip entry if reqd in pigmi lights pole fixinf screws / clmp complete as required complete all as specified and directed by Engr in Charge. |
| 52 | M & L in repair for Earthing complete with galvanised steel earth plate electrode of size (600 x 600 x 6) mm thick buried directly into ground vertically to depth not less than 2.25 metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level, surrounded on all sides by alternate layers of 150 mm thick charcoal and common salt, connected to MS galvanised earth lead wire 4.0mm dia by means of bolts, nuts, washer, check nuts of galvanised iron or steel all as shown in Electrical plate No. 3, GI strip laid in dia 40 mm bore light grade GI Pipe laid in floor and fixed to wall with proper size of clamps and watering pipe of bore 20 mm dia GI light grade including wire mesh funnel, PCC, earth chamber pit (30X30X30cm) with PCC 1:2:4 type B-1 using 20 mm grade stone aggreate including form work cement mortar including CI Pit cover with frame necessary excavation and earth work in any type of soil including testing on completion for desired result all as specified. ( DBs and Lighting conductor) complete all as specified and directed by Engr in Charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 06, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 25, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
TodayAug 27, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 2 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender