Tender For Provn Of 01 X Covered Approach From Living Line To Toilet Block Of 72 Arty Be C At Nanak Hill Mil Stn (Nhsm) And Rep/ Replacement Of Wiring Of Bldg No T-366 (Cl Sec) Of 5118 Asc Coy At Nimu Mil Stn Under Age (I) Nimu
Tender Value
9.46 Lakhs
Estimated cost
Bid Submission
25 Aug 2026
2 days left
EMD
20000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Leh → Ladakh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Provn Of 01 X Covered Approach From Living Line To Toilet Block Of 72 Arty Be C At Nanak Hill Mil Stn (Nhsm) And Rep/ Replacement Of Wiring Of Bldg No T-366 (Cl Sec) Of 5118 Asc Coy At Nimu Mil Stn Under Age (I) Nimu
BOQ
| Sl. No. | Item Description |
| 1 | Excavation in trenches not exceeding 1.5m wide and n exc 1.5m in depth for foundations, laying of pipes etc and not exceeding 10 Sqm on plan for manhole, laying of cable etc and not exceeding 1.5 meter in depth and getting out in hard/dense soil, complete all as specified and directed by Engr-in charge. |
| 2 | M&L Cement concrete type D-2 1:4:8 (using 40mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and directed by Engr-in charge. |
| 3 | M&L for PCC 1:3:6 type C-1 using 20mm graded crushed stone aggregate) block masonry with solid block exc 10cm in width and set as in wall etc in CM 1:6. complete all as specified and directed by Engr-in charge. |
| 4 | M & L 75mm thick Cement concrete type D-2, 1:4:8 (using 40mm graded aggregate) as in sub base complete all as specified and directed by Engr-in charge. |
| 5 | TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire(annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engr-in charge. |
| 6 | All as per item No 5 here-in-before but of 6 and incl 10mm dia in stirrups, spacers and binders complete all as specified and directed by Engr-in charge. |
| 7 | Form work to sides of roof beams band and similar and soffits of girder, lintle, cantilever shelves including supports flat rough surface of concrete complete all as specified and directed by Engr-in charge. |
| 8 | M & L RCC Nominal mix type B-1 1:2:4 (20mm graded crushed stone agg) as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed by Engr-in charge. |
| 9 | S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beams, tee, angle, channel or flat sections) including distance piece, cleats etc. conforming to Fe 410 W (Gde- E- 250) quality A complete all as specified and directed by Engr-in charge. |
| 10 | S&F Mild steel bolts purpose made with hexagonal or square head one end and screwed the other, or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square nut exceeding 30cm long and dia of neck exceeding 12mm but not exceeding 20mm, complete, all as specified and directed by Engineer-in-Charge. |
| 11 | M&L applying two coats of synthetic enamel painting to new surfaces steel based over a coat of red oxide primer exc. 10cm width/girth including preparation of surfaces including filling with filler where reqd complete all as specified and directed by Engr-in charge. |
| 12 | S&F Prepainted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall fixed with self tapping screws as spd and directed complete all as specified and directed by Engr-in charge. |
| 13 | S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed by Engr-in charge. |
| 14 | M&L for Rendering 10mm thick on fair faces of brickwork or concrete surfaces in cement mortar (1:6) and finished even and smooth without using extra cement complete all as specified and directed by Engr-in charge. |
| 15 | M & L preparation of new plastered surfaces and applying three coats of white wash on walls complete all as specified and directed by Engr-in charge. |
| 16 | S&F Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed by Engr-in charge. |
| 17 | M&L for Rendering 15mm thick on fair faces of brickwork or concrete surfaces in cement mortar (1:4) with WPC and finished even and smooth without using extra cement (Note : WPC will be measured and paid separately) complete all as specified and directed by Engr-in charge. |
| 18 | Supply only WPC complete all as specified and directed by Engr-in charge. |
| 19 | M&L preparing new plastered surfaces of walls and applying two coats of cement base paint over a coat of alkali resistant primer all as specified complete all as specified and directed by Engr-in charge. |
| 20 | M & L 2nd class hardwood 35mm thick Plain, framed, panelled shutters (Two panels), with lock rail and panels of 9mm B.W.P commercial ply or 12 mm veneered particle board with commercial veneering on both faces. the size of rail and stile as per IS :1003 (part-1) kiln seasoned and chemicaly pressure treated supplied and fitted to chowkats complete all as specified and directed by Engr-in charge. |
| 21 | S & F Mild steel 100mm long Butt hinges, medium weight, cold rolled mild steel, and fixed complete all as specified and directed by Engr-in charge. |
| 22 | S & F extruded aluminium alloy handles, 150mm size, fabricated type, anodised complete all as specified and directed by Engr-in charge. |
| 23 | S & F Aluminium alloy, anodised, sliding door bolt 250mm size with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast alumimnium alloy and fixed complete all as specified and directed by Engr-in charge. |
| 24 | S & F Aluminium anodised, barrel tower bolt of extruded section and fixed, 150mm size of extruded sections and fixed complete all as specified and directed by Engr-in charge. |
| 25 | M&L applying two coats of synthetic enamel painting to new surfaces wooden based over a coat of pink primer exc. 10 cm width/girth including preparation of surfaces including filling with filler where reqd complete all as specified and directed by Engr-in charge. |
| 26 | Surface excavation n.exc (not exceeding) 30cm deep and averaging 15cm deep and getting out hard/dense soil complete all as specified and directed by Engr-in charge. |
| 27 | M & L hard core of broken stone and boulders gauge n exc 60mm deposited spread and level in layers n exc 15cm thick watered and rammed to a true surface complete all as specified and directed by Engr-in charge. |
| 28 | Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge. |
| 29 | S & F Sheet glass, ordinary quality and glazing with oil putty in square exc 0.5 sq. m in each pane. complete as per architectural drawings and the directions of Engineer-in-charge. |
| 30 | S&F 9mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with nails to timber frame work as in Ceiling, complete all as specified and directed by Engr-in crage. |
| 31 | Returning, filling under floor excavated soil including spreading, leveling watering and well ramming in layers not exceeding 25cm thick complete all as specified and directed by Engr-in charge. |
| 32 | Removing excavated material (soils) to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point, complete all as specified and directed by Engr-in charge. |
| 33 | Supply and laying or fixing or passing through pipe, 6sq mm 2core 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed 6 sq. mm 2 CORE nominal cross section in service connections |
| 34 | M&L in repair for point wiring with PVC FRLS insulated single core cable of stranded copper conductors of size 1.5 sqmm, 1100 volt grade drawn in and including rigid PVC casing caping accessories lain on wall/ceiling surface and fixed with PVC saddles and back-plate and GI screws, including PVC insulated single core cable of stranded copper conductor of size 1.5 sqmm as earth continuous wire connected to common earth and PVC Board for housing like switches, sockets, fan regulators etc all as directed by Engineer-in-Charge for following :-(a) One light point/one fan point controlled by one switch |
| 35 | S&F Switch piano flush type 5 Amp, single pole, one way complete all as specified and directed by Engr in Charge. |
| 36 | S&F in replacement of existing worn out ceiling light with enviromental friendly, new generation, aesthetically designed, ultra modern recessed mounted LED light luminaries of size 595 mm x 595 mm(2'x2') an independent Isolated, electronic LED driver (SMPS based constant current supply) housed in CRCA powder coated sheet of system wattage - 36/40/42 Watt, Lumen out put- 4000-4300 Lm, THD < 10%, PF > 0.9, having short circuit and surge protection suitable for Armstrong/ Grid ceiling with all connected accessories including making connection with three core PVC insulated, sheathed copper conductor cable of size 23/0.0076 complete all as specified and directed. |
| 37 | Taking down carefully aluminium/Copper point wiring light, fan socket or power complete fitting such as switches, ceiling rose, fan regulator, socket including light fitting etc complete with /PVC /MS conduit and T/W battern / casing caping and all as specified and as directed by Engineer-in-Charge. |
| 38 | Taking out old unsv Service wiring of any size/make/ type etc from excavted tranches/ on pole passing through pipes etc from different locations complete all as specified and directed by the engr in charge. |
| 39 | Supply and laying or fixing or passing through pipe, 16sq mm 2core 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed 16 sq. mm 2 CORE nominal cross section in service connections |
| 40 | M&L for point wiring with PVC FRLS insulated single core cable of stranded copper conductors of size 1.5 sqmm, 1100 volt grade drawn in and including rigid PVC casing caping accessories lain on wall/ceiling surface and fixed with PVC saddles and back-plate and GI screws, including PVC insulated single core cable of stranded copper conductor of size 1.5 sqmm as earth continuous wire connected to common earth and PVC Board for housing like switches, sockets, fan regulators etc all as directed by Engineer-in-Charge for following :-(b) One 3 pin 5 amps socket outlet independent with cables 2.5 sqmm size |
| 41 | M&L for point wiring with PVC FRLS insulated single core cable of stranded copper conductors of size 1.5 sqmm, 1100 volt grade drawn in and including rigid PVC casing caping accessories lain on wall/ceiling surface and fixed with PVC saddles and back-plate and GI screws, including PVC insulated single core cable of stranded copper conductor of size 1.5 sqmm as earth continuous wire connected to common earth and PVC Board for housing like switches, sockets, fan regulators etc all as directed by Engineer-in-Charge for following :-(c) One 3 pin 5 Amp socket outlet on same board with cables 2.5 sqmm size |
| 42 | All same as per item No 40 above but with conductor of size 4 sqmm (Nominal area) for one 3 pin socket outlet 15 Amps on independent board complete and earth continuity wire with 4 sqmm PVC insulated stranded copper conductor Cable. |
| 43 | S&F Socket 2 in 1, 5 pin 5 Amp flush type complete all as specified and directed by Engr In Charge. |
| 44 | S&f Switch socket combination 2 in 1, 3 pin, 5 Amp flush type complete all as specified and directed by Engr in Charge . |
| 45 | S&F Switch Socket Combination 2 in 1, 3 pin, 15/16 amp flush type Universal complete all as specified and directed by Engr in Charge . |
| 46 | M&L for ceiling rose surface Bakelite 65x50mm two to three terminal complete all as specified and as directed by Engr-in-Charge. |
| 47 | S & F LED light fitting 1x9W/1X10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size all as specified and directed by Engr in Charge. |
| 48 | S&F basic all purpose surface and wall mounted LED batten with polycarbonate housing and integreted electronic driver of cap 20 watt, 4 feet long, with all accessories complete all as per specified and as directed by Engr-in-Charge. |
| 49 | Supply and fixing LED luminaire 600 mm x 600 mm, 40 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete. |
| 50 | S&F in repair sheet metal powder coated versatile Double door SPN distribution board, 12 way suitable for MCB's fitted with copper bus bar rated 200amps, neutral link , earth bar and din rail suitable for use on 240 Volt, 50Hz all as directed by Engr in Charge. |
| 51 | M&L in repair for MCB SPN 63 Amp, 240V with 10KA breaking capacity of 'C' series in distribution boards all as specified and directed. |
| 52 | S&F in repair to MCB SP 6-32 Amp with 10KA breaking capacity of 'C' series in distribution boards with all accessories complete all as per specified and as directed by Engr-in-Charge. |
| 53 | Dismantling and Taking down old u/s street / building sequrity Light fittings from poles, flood lights, post top lantern lights and garden lights for replacement with LED fittings all as specified and as directed by Engr in Charge. |
| 54 | Supply and fix LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete Specified and directed by Engr in charge. |
| 55 | M&L for GI bracket 1.5 mtr long made out of GI pipe 40mm dia bend to suitable radius incl clamps nuts bolts washers incl painting with aluminum paint etc complete all as specified and directed by Engr in charge. |
| 56 | S&F in repair Air termination, single pointed, copper rod 12mm dia and 300mm long different locations / Bldg complete all as specified and directed by the engr in charge. |
| 57 | S&F in repair Test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 nos. 8mm dia 25mm long hex. head screw complete all as specified and directed by the engr in charge. |
| 58 | S&F in repair Galvanised earth lead wire 4.0mm dia for roof conductors and down conductors above ground complete all as specified and directed by the engr in charge. |
| 59 | Supply and fix in repair or laying 32 mm light grade GI Tubes in trenches/on wall/ poles/ structures as in repairs GI tubeing light grade for road crossing/ for cable protection / fixing of pigmi lights etc, of the folling size including necessary provision for cable / Strip entry if reqd in pigmi lights pole fixinf screws / clmp complete as required complete all as specified and directed by Engr in Charge. |
| 60 | M & L in repair for Earthing complete with galvanised steel earth plate electrode of size (600 x 600 x 6) mm thick buried directly into ground vertically to depth not less than 2.25 metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level, surrounded on all sides by alternate layers of 150 mm thick charcoal and common salt, connected to galvanised earth lead wire 4.0mm dia by means of lugs, bolts, nuts, washer, check nuts of galvanised iron or steel all as shown in Electrical plate No. 3, GI strip laid in dia 40 mm bore light grade GI Pipe laid in floor and fixed to wall with proper size of clamps and watering pipe of bore 20 mm dia GI light grade including wire mesh funnel, PCC, earth chamber pit (30X30X30cm) with PCC 1:2:4 type B-1 using 20 mm grade stone aggreate including form work cement mortar including CI Pit cover with frame necessary excavation and earth work in any type of soil including testing on completion for desired result all as specified. ( DBs & Lighting conductor) |
| 61 | Taking out old unserviceable underground cable of any size/ make/ type etc from excavated trenches/ on poles/ passing through pipes etc from different locations complete all as spd. |
| 62 | Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sq mm 4 core complete all as specified and as directed by the Engineer - in - Charge. |
| 63 | Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth for taking out pipe line etc for repairs / laying cables etc and getting out in soft / loose soil complete all as specified and as directed by the Engineer - in - Charge. |
| 64 | Material and labour for un reinforced pre cast concrete cable cover class LV type I, flat size 250 mm x 150 mm x 40 mm. |
| 65 | Sand cushioning to under ground cable complete all as specified in clause 19.75 of SSR Part - I. |
| 66 | Dismantling and Taking down LT U/S panels incl all outgoing and incoming connections and making good the disturbed area from site all as specified and directed by Engineer-in-Charge. |
| 67 | M&L for Busbar chambers with 4 aluminium busbar strip of rating 400 Amp 6 way fixed on angle iron of size 40mm x40mm x5mm complete all as specified and directed by Engineer in Charge. |
| 68 | M & L in repaIr for Earthing complete with galvanised steel earth plate electrode of size (600 x 600 x 6.3) mm thick buried directly into ground vertically to depth not less than 2.25 metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level, surrounded on all sides by alternate layers of 150 mm thick charcoal and common salt, connected to MS galvanized earh strip of size 32 x 6 mm by means of lugs, bolts, nuts, washer, check nuts of galvanised iron or steel all as shown in Electrical plate No. 3, wire protected by dia 15 mm bore light grade GI Pipe laid in floor and fixed to wall with proper size of clamps and watering pipe of bore 20 mm dia GI light grade including wire mesh funnel, PCC, earth chamber pit with PCC 1:2:4 type B-1 using 20 mm grade stone aggreate including form work cement mortar including CI Pit cover with frame necessary excavation and earth work in any type of soil including testing on completion for desired result all as specified. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 06, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 25, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 2 daysAug 27, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 4 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender