Tender For flood damage repair / Renovation Of L.I. Scheme At Debtabari Under Budhjungnagar Vc Of Lefunga Rd Block During The Year 2026-27 / Sh:- Replacement Of 1 (One) No. Pump Motor Set, Renovation Of Pump House And Pipe Line In/C Electrical Access
Tender Value
9.65 Lakhs
Estimated cost
Bid Submission
13 Aug 2026
5 days left
EMD
19306
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
tripura → Tripura
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for flood damage repair / Renovation Of L.I. Scheme At Debtabari Under Budhjungnagar Vc Of Lefunga Rd Block During The Year 2026-27 / Sh:- Replacement Of 1 (One) No. Pump Motor Set, Renovation Of Pump House And Pipe Line In/C Electrical Accessories And Other Allied Works Within The Jurisdiction Of W.R. Sub-Division Mohanpur. (Job No. Tr/13/Minor Works/Wrd-I/2026-27)
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling GS sheet roofing including ridges, hips, valleys, gutters wind ties etc. including dismembering and stacking of serviceable materials and unserviceable materials separately with all lifts and upto a lead of 50 m etc.complete as per direction of the Engineer- in-charge. |
| 2 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :i) Of area 3 sqm and below. |
| 3 | Demolishing brick work including stacking of serviceable materials and disposal of unserviceable materials with all lifts and upto a lead of 50m etc.complete as per direction of the Engineer- in-charge:- i) In cement mortar |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level.i) 1 : 2 : 4 ( 1 cement : 2 fine sand : 4 graded well burnt brick aggregate of 20 mm nominal size) |
| 5 | First class brick work in foundation and plinth including cost of all materials as required complete.I) In Cement mortar 1:4 ( 1 cement : 4 fine sand) |
| 6 | Half brick masonry work with first class bricks in superstructure upto floor five level including cost of all materials as required complete:-i) In cement mortar 1:4 ( 1 cement : 4 fine sand ) |
| 7 | Reinforcement for R.C.C. work including straightening,cutting, bending, placing in position and binding all complete upto plinth level.A) Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 8 | Centering shuttering including struttings, propping etc. and removal of form work for: i) Suspended floors roofs landings balconies and access plat form with timber plank |
| 9 | ii) Columns, Pillars, Piers, Abutments, Posts and Struts with wooden plank. |
| 10 | Reinforced cement concrete work in beams ,suspended floors, roofs having slope upto 15 degree landing balconoes shelves chajja lintels bands plain windows sills , staircase upto floor five level excluding cost centering , shurttering, finishing and reinforcement.i) 1:2:4(1 cement:2 fine sand:4 gradded well burnt aggt.20 mm nominal size) |
| 11 | Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6mm angle iron and 3mm M.S. gusset plates at the junctions and corners, & with cleats with bolts & nuts, rivets, locking arrangement, handles, hooks & eyes, pinlets including embedding in cement concrete of required grade for fixing in position, all necessary fittings, including applying a priming coat of approved steel primer etc. complete as required:-i) Using flates 30 x6mm for diagonal braces and central cross piece. |
| 12 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. all complete.i) Fixed to steel windows by welding. |
| 13 | Providing and laying cement concrete 1:2:4 (1 cement : 2 fine sand : 4 graded well burnt brick aggregate) flooring finished with a floating coat of neat cement including cement slurry, rounding of edges and strips etc.complete.i) 40 mm thick with 20 mm well burnt brick aggregate |
| 14 | Steel work in built up tubular( round , square or ractangular hollow tubes etc) trusses etc. includng cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, in/c welding and bolted with special shaped washers etc.complete i) Hot finished welded type tubes |
| 15 | Providing and fixing M.S. round holding down bolts with nuts and washer complete as per standard design. |
| 16 | Providing & fixing MS nuts & bolts. Including washers complete as per standerd design;-(a) Upto 300 mm length |
| 17 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 fine sand : 6 graded well burnt brick aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth. |
| 18 | Charges for fixing corrugated G.S. Sheet roofing fixed with polymer coated J or L hooks 8 mm diameter, bolts and nuts 6 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with lead and including a coat of approved steel primer and two coats of approved epoxy paint on overlapping of sheets complete ( upto a pitch of 60 degrees ) over a built structure including all types of necessary scaffoldings etc. but excluding the cost of the C.G.S. sheets, purlins, rafters and trusses etc.as per clauses of Chapter - 12 of CPWD specification. a) 0.63 mm thick with zinc coating not less than 275 gm / m2 |
| 19 | Providing corrugated G.S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead and including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces) excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.i) 0.63 mm thick with zinc coating not less than 275 gm / m2 |
| 20 | Providing ridges or hips of width 60 cm overall width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete.i) 0.63 mm thick with zinc coating not less than 275gm/m2 |
| 21 | Providing and Installation of Horizontal pump motor set (Centrifugal) with allied equipments by maintaining proper level / slope , alignment etc. in/c all necessary nuts & bolts, washers etc. at site of work and making necessary electrical connection with main switch / starter with motor in/c commissioning & trial run for 10 hrs. in two spell as per direction of the Engineer-in-charge.i) 25 HP motar with 60 LPS 22 m head pump |
| 22 | 12 mm cement plaster of mixi) In Cement mortar 1:4 ( 1 cement : 4 fine sand ) |
| 23 | Neat cement punning . |
| 24 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer]:i) Two or more coats on new work |
| 25 | Painting on G.S. sheet with synthetic enamel paint ( two or more coats ) of approved brand and manufacture of required colour to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer] : i) New work (two or more coats) including a coat of appropriate steel primer but excluding a coat of mordant solution |
| 26 | Providing and fitting fixing of 6 feet x 4 feet x 1 inch (thickness) Gamair wood / plywood pannel board for fitting fixing of electrical items, in/c 2 nos MS angle post ( size 2 inch x 2 inch x 9 feet ), nuts & bolts etc. for irrection of the same by 1:1.5:3 cement concrete casting ( 1 feet x 1 feet x 2 feet) below the ground level and painting two or more coats & plastic paint as per specification and direction of the Engineerin-charge. |
| 27 | Providing & fitting fixing Steel sheet enclosed switch Fuse unit (Suitable for DIN fuse) triple pole with Neutral Link (TPN) , 415/500 Volt,L&T/ Havells/BCH make etc complete as per Specification direction of Engineer-in-Charge.i) Current range 63 Amps. |
| 28 | ii) Current range 200 Amps |
| 29 | Providing & fitting fixing of Fully Automatic Star Delta type Motor startar ( 3ph, 50 Hz, 415V in steel sheet enclosure with Conductors and Timer etc. complete suitable for motor pump L&T, BCH,ABB make as per Specification direction of Engineer-in-Charge.i) 25HP/18.5 kw Relay range within 13-21 +10% |
| 30 | Supplying & fitting fixing of PVC insulated Copper Wire with all electrical equipments including trial run etc. complete (ISI Marked) on the pannel board of approved quality.i) 7/16 Copper Wire |
| 31 | Supplying and fitting fixing power capacitor (ISI Marked) of approved quality.i) 12.5 KVAr |
| 32 | Providing and fitting fixing 3 phase indicating lamp fiited with panel board with three different colour lamps with batten holder complete as per specification and direction of the Engineer-in-charge. |
| 33 | Providing & fixing 200 Amps busber of size 600 x450x100 mm with 4 nos. copper strips of size 450x40x4 mm of approved quality |
| 34 | Providing and fixing G.I. pipes of medim class as per IS : 1239 with latest amendment complete with G.I.fittings including trenching and refilling etc. complete as per CPWD specification and direction of the Engineer - in - charge.External worki) 40 mm dia. nominal bore |
| 35 | Providing and fixing C.I. non-return valve of approved quality as per CPWD specification and direction of the Engineer - in -chargei) 125 mm nominal bore |
| 36 | Providing and fixing C.I. sluice valves ( with cap ) complete with bolts, nuts, rubber insertions etc. ( the tail pieces if required will be paid separately ) as per CPWD specification and direction of the Engineer - in - charge.i) 150 mm dia. A. PN - 1.6 |
| 37 | ii) 125 mm dia. A. PN - 1.6 |
| 38 | Providing & fixing of GI . Bend , elbow in the pipe line including testing of joints complete as per CPWD specification and direction of the EIC. i) 125 mm dia |
| 39 | ii) 150 mm dia |
| 40 | Providing & fitting fixing of MS flange ( 8 mm wall thickness ) by welding with G.I. / MS pipe and placing position as per specification and the direction of the Engineer-in-charge.i) 150 mm dia |
| 41 | ii) 125 mm dia |
| 42 | Providing & fitting fixing rubber flange washer 6mm thick at site of work of approved quality.i) 125 mm dia. |
| 43 | ii) 150 mm dia. |
| 44 | Providing and fitting fixing of moving iron type Range 0-500 V. 96 x 96 mm size AC volt meter (L & T/ AE make ) with selector switch as a electrical instrument of the panel board as per specification and direction of the Eng-in-charge. |
| 45 | Providing and fitting fixing of moving iron type Range 0- 100/0-200 amps. 96 x 96 mm size AC amps meter (L & T/ AE make ) with selector switch as CT coil as a electrical instrument of the panel board as per specification and direction of the Eng-in-charge. |
| 46 | Supplying & fitting fixing of C.I. tail piece of approved quality at site of work. i) 150 mmdia |
| 47 | ii) 125 mm dia |
| 48 | Providing and fitting fixing PVC suction hose pipes of wall thickness 6 mm. as per relevant IS specification and direction of Engineer-in-charge.i) 150 mm dia |
| 49 | Providing and fitting fixing MS Foot valve as per relevant IS specification and the direction of the Engineer-in-charge.a) 150 mm dia |
| 50 | Providing & fitting fixing MS hose clamp with nuts & bolts etc.complete as per relevant IS specification and direction of Engineer-in-charge.a) 150mm dia |
| 51 | Excavating trenches of required width for pipes, cables, etc. including excavation for sockets and dressing of sides ramming of bottoms , depth minimum 1.25m including getting out the excavated soil and then returning the soil as required in layers not exceeding 20 cm in depth including consolidating each deposited layers by ramming watering etc. and disposal of surplus excavate dsoil as directed within a lead of 50 m as per CPWD Specification & direction of Engineer-in-charge.A) All kinds of soil.a) For pipe not exceeding 90mm dia . |
| 52 | b) For pipe exceeding 90 mm dia but not exceeding 300 mm dia . |
| 53 | B) For G.I. / C.I. / D.I. pipes in new worka) For pipes exceeding 90 mm dia but not exceeding 300 mm dia |
| 54 | Providing and laying different dia rigid UPVC pipes of Working Pressure 4.0 kg/ sq.cm. complete with necessary coupler and solvent cement as per CPWD Specification & direction of Engineer-in-charge.i) 90 mm dia |
| 55 | ii) 110 mm dia |
| 56 | iii) 140 mm dia |
| 57 | iv) 160 mm dia |
| 58 | v) 200 mm dia |
| 59 | Providing and fixing G.I. pipes medim class as per IS : 1239 with latest amendment complete with G.I. fittings including trenching and refilling, cutting and making good the walls etc.complete as per CPWD specification and direction of the Engineer - in - charge.a)External work.i) 150 mm dia. nominal bore |
| 60 | ii) 125 mm dia.nominal bore |
| 61 | Providing and fitting fixing of G.I hydrant suitable for PVC pipes asper standard specification complete as per direction of Engineer-incharge (Rate excluding the cost of NTP control valve).80X50 mm dia. |
| 62 | Providing and fitting fixing of different dia rigid UPVC unequal Tee (including earth cutting & backfilling all socketted) suitable for pipes as per IS specification of working pressure 4.0 kg/sq.cm confirming to IS: 10124 (part-V) as per CPWD Specification & direction of Engineer-in-chargei) 160x160x140 mm dia |
| 63 | ii) 160x160x110 mm dia |
| 64 | iii) 160x160x90 mm dia |
| 65 | iv) 140x140x110 mm dia |
| 66 | v) 140x140x90 mm dia |
| 67 | vi) 110x110x90 mm dia |
| 68 | Labour charge for repairing of leakage in existing UPVC distribution system including required earth cutting and fitting fixing of necessary coupler etc. complete and refilling the trench with available excavated earth as per direction of the Engineer-in-charge. (Payment of couplers, tees, reducers etc will be made separately)i) 250 mm dia to 110 mm dia. |
| 69 | ii) 90 mm dia. |
| 70 | Providing, fixing and laying fabricated UPVC socket / coupler conforming to IS : 10124 ( Part 2 ) with solvent cement conforming to IS : 14182 including testing of joints complete as per CPWD specification and direction of the Engineer - in -charge.i) 90 mm dia. |
| 71 | ii) 110 mm dia. |
| 72 | iii) 140 mm dia. |
| 73 | iv) 160 mm dia. |
| 74 | Providing, fixing and laying fabricated UPVC straight reducer conforming to IS : 10124 ( Part 3 ) with solvent cement conforming to IS : 14182 including testing of joints completeas per CPWD specification and direction of the Engineer - in -charge.i) 160 x140 mm dia |
| 75 | ii) 140 x110 mm dia |
| 76 | iii) 110 x90 mm dia Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 06, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 13, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 5 daysAug 14, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 6 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender