Tender For Na...Kudal Industrial Area...... Replacement Of Pumping Machineries Along With Allied Works At Jackwell & Wtp @Kudal Industrial Area.
Tender Value
10.87 Crore
Estimated cost
Bid Submission
31 Aug 2026
19 days left
EMD
5.44 Lakhs
Bank guarantee accepted
Document Fee
30680
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Raigad → Maharashtra
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Na...Kudal Industrial Area...... Replacement Of Pumping Machineries Along With Allied Works At Jackwell & Wtp @Kudal Industrial Area.
BOQ
| Sl. No. | Item Description |
| 1 | Sub Estimate - Replacement of pumping Machineries along with allied works at Jackwell @ Kudal Industrial Area. -- Providing, installing, commissioning and testing of VERTICAL TURBINE, self water lubricated above floor type pump with VHS motor capable of discharging raw water at the rate of 286 Cum/ Hr. at the duty point head and operating at the bowl head of 43 Mtr. with 1450 rpm with IE2 1500 RPM (Synchronous Speed) Vertical solid shaft Totally Enclosed Fan Cooled squirrel cage induction motor conforming to IP-55, Continuously rated(S1) suitable for operation on 415V ± 10% volts, 3ph, 50 Hz ± 5%, combined variation 10%, AC supply ambient 50 deg.C with “F” Class Insulation with temp. rise limited to class “B” (75 deg C) altitude less than 1000m above m.s.l. Performance efficiency Values are conforming to IS 12615 / IEC 60034 of capacity to run the pump of minimum 55 KW / 75HP etc. complete with all accessories . Pump including stainless steel basket type strainer, bowl assembly, column assembly, discharge head, MS base plate of suitable size with minimum thickness of 24 mm, connecting stool etc. complete as per latest IS specifications. The 4 stage pumps with column pipes shall be manufactured from ERW pipes of 10 mm thick and each of maximum 1.5 m length provided with anticorrosive and special treatment paint and all line shafts impellers shafts of stainless steel AISI 410 and impeller should be of Bronze including 25 /30 mm M.S. sole plate and base frame of ISMB 300 x 150 mm with accurate standard 150 mm dia to read entire range of pressure gauge with necessary tubing and isolation cock. including all consumable materials, accurate digital type glycerin Pressure gauge to read entire range of pressure complete with necessary tubing. The complete pump assembly from strainer to discharge head shall have to be connected with stainless steel AISI-304, 316 nut bolts as per detailed specification and the pump operating at 1480 RPM including Component to be coated for VT pump, including providing required C.C. foundation, base channel, all allied material, cutting welding etc. complete. The pump should have Water Lubricated turbine pump complete with Bowl Assembly, Column Assembly, Discharge Head, PLT & Strainer and flat efficiency characteristics between operating range as per detail item specifications. Supplying, installing, commissioning and testing of 55 KW/ 75 HP vertical solid shaft totally enclosed fan cooled (TEFC) IP 55 type squirrel cage induction motor, suitable for operation on 415 +/- 10% volts, 3 phase, 50 cycles/ sec. (Hz), 1500 RPM (synchronous speed) AC supply having Performance efficiency at full load is 80% & confirming to IS 12615/IEC 60034 and power factor not less than 0.87 @ full load fitted with non-reversible ratchet arrangement and complete with top half clutch with 'F' class insulation with temp. rise limited to class 'B' (75 degree C) for ambient temp not exceeding 45 degree etc. complete. |
| 2 | Designing ,Providing, erecting, commissioning of LT Set switch gear FCMA Soft Starter panel along , cubical type, MS sheet fabricated from 14 gauge CRCA sheet including all accessories, switch gear, Copper busbar, foundation channel this item includes Designing, providing, erecting, testing & commissioning of PLC cum FCMA starter without any active electronic component, moving parts & totally harmonics free, FCMA starter lifted with all accessories including providing & applying painting to frame with international orange colour & two doors & covers siemens gray etc. The starter shall be suitable for 55KW/75HP induction motor operating at 415/440 Volts, 3 phase 50 Hz AC supply. The starter shall be flux compensated magnetic amplifier type (FCMA type). The details list of material required for L.T. Starter panel are mentioned in itemwise specification consist of material quantity and make.The main components of panel are 2 No. FCMA Starters, 1 No. Incomer, 1 No. Changeover, 2 No. Outgoings, Auxillary Feeder, Metering & Copper Bus Bar etc. Panel fabricated from 14 Gauge CRCA MS sheet with powder coating including all accessories, switchgear, indicating lamps, push buttons, cables, meters, Copper busbar, foundation channel, with all selfcontained inter connections, internal wiring with ferrules, suitable engraved designation labels etc. complete. |
| 3 | Designing, Supplying, erecting ,testing & Commissioning of 75KVAr APFC Panel including all accessories, switchgears, control wiring etc. complete. Panel fabricated from 14 Gauge CRCA MS sheet with powder coating including all accessories, switchgear, indicating lamps, push buttons, cables, meters, Copper busbar, foundation channel, with all selfcontained inter connections, internal wiring with ferrules, suitable engraved designation labels etc. complete. |
| 4 | Providing, erecting, testing & commissioning of 100KVA DG Set for Back up including all allied works etc. complete at Jackwell, Kudal. The item includes Foundations of DG Set, earthing, 2 run of LT Cabling with DWC Pipe enclosure , AMF Panel, Weather shed etc. complete. Permission from Electrical Inspector shall be obtained as per requirement. |
| 5 | Providing, installing, commissioning & testing of 250 mm dia PN 1.6 Tilting Check Valve c/w Lever & Counter Weight, DI D/F slanted seat tilting disc swing check valve in single piece body. Body & disc. Of ductile cast Iron, shaft of stainless steel & bearing of zinc free bronze, Electrostatic epoxy powder / liquid coating inside & outside blue colour with minimum coating thickness of 150 micron. Complete with nuts, bolts, gaskets, washers etc. Suitable for pressure rating of 16 kg./ sq.cm. for seat without bypass arrangement as per detailed specifications complete including providing supporting CC block in M-150 grade concrete etc. complete. |
| 6 | Supplying erecting testing and commissioning DI D/F non-rising spindle soft seated glandless Gate Valves with body and bonnet of Ductile cast iron of grade GGG-40, wedge with fully encapsulated EPDM rubber (approved for drinking water ) and seals of NBR. The valves should be with replaceable stem nut and replaceable sliding shoes. Valve stems shall be of single piece thread rolled type. Valve shall have 3 “O” rings of NBR for stem sealing. Gate valve shall be compatible for buried application without valve chamber. Face-to- face dimensions as per BS 5163-89/IS 14846 – PD/EN 558 F4 and flange connections as per EN1092-2/IS 1538, Maximum valve operating torque should be at least 40% less than the torque as stated in the standard EN 1074. Electrostatic epoxy power / liquid coating (EP-P) inside and outside color blue RSL 5005 with minimum coating thickness of 250 microns. The EPDM rubber & Epoxy coating should be potable water certified. Material of construction :- Body, Bonnet :- Ductile Iron GGG40 (EN-JS-1030) Wedge, (Fully rubber encapsulated):- Ductile Iron GGG 40(EN-JS-1030) encapsulated with EPDM rubber- Portable water certified. Spindle / Stem: - SS: AISI 420 Stem Nut:- Brass Bonnet Gasket: - EPDM rubber potable water certified Internal fasteners: - Stainless Steel SS304 Stem Sealing :- Toroidal NBR sealing rings (Min 03 ‘O’ Rings) Coating: - Inside & Outside epoxy powder coated; DFT minimum 250 micron, shade RAL, shade RAL, 5005 (Signal Blue) potable water certified. excluding GST) 250 mm dia ,PN 1.6 rating |
| 7 | Design ,Supply , Erection , Testing & commissioning of kinetic Air Valve DN 100 mm, including sluice valve PN 1.6 and its Operation Auto etc. complete. |
| 8 | Dismantling Joints - Providing, erecting and commissioning M.S. Dismantling joint as per requirement and Department's approved drawing and specifications, including machining and rubber rings and suitable for 16 kg/cm2 working pressure with required flanges of suitable size with nut bolts etc complete. The joint should have through long bolts so that during normal working pressure there should be no sliding movement of sliding flanges. L.O.F. ( length over flange ) should not be less than 75% of dia. - PW 6-4) 250 mm dia Joint |
| 9 | Providing, erecting testing and commissioning at work site fabricated MS Pipes and specials with necessary circumferential and longitudinal joints with cutting, welding including cost of MS Pipes and flanges,nut bolts etc. with loading, unloading , transportation etc. complete. |
| 10 | Providing and fabricating structural steel work in rolled sections like joists, channels, angles, tees etc. as per detailed design and drawings or as directed including cutting, fabricating, hoisting, erecting, fixing in position making riveted / bolted /welded connections without connecting plates, braces etc. and including one coat of anticorrosive paint and over it two coats of oil painting of approved quality and shade etc. complete. |
| 11 | Providing flooring insulation for walk way and approach way etc. complete for Main LT Panel and control Panel area at RWW Kudal |
| 12 | LT Cables (Aluminum) (CB-LT/AL) - Supplying, erecting & terminating FR XLPE insulated, galvanised steel wire armoured (round) cable, 1100 V 4 core 6 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL |
| 13 | Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable, 1100 V 4 core 120 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL |
| 14 | Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable, 1100 V 4 core 185 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL |
| 15 | Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable, 1100 V 4 core 25 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL |
| 16 | Cable Enclosures (CB-CE) - Supplying and laying (including excavation of suitable width & depth up to 90 cm) 50 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, complete. |
| 17 | Plate, Pipe type Earthing (EA-EP) - Supplying, installing and testing earthing with copper earth plate size 60 x 60 x 0.315 cm with funnel with a wire mesh for watering and brick masonry block C.l. cover with minimum 25 kg Carbon based environment friendly back fill ground ehancing compound complete with all accesories of copper materials & recording the results as per specification no EA-EP/EF |
| 18 | Accessories - Supplying and erecting fencing of section having size at least 2450 mm in height from ground level and 1200 mm width with angle iron frame work erected in CC foundation and painted complete with provided earthing as per specification no. SS-AS/FSG |
| 19 | Supplying and erecting 50 x 50 x 6 mm angle iron as corner support 2.45m long fixed at the middle of the fencing frame and the other side inclined at 30 degree angle, in cement concrete foundation of 15 x 15 x 40 cm complete duly painted with one coat of red oxide and two coats aluminium paint complete. |
| 20 | Supplying and erecting double leaf hinged door each 1500 mm in width x 2450 mm in height using B class GI pipe, hinges and angle iron supports, chain link wire mesh (jali) complete supported on channel iron, erected in foundation and painted complete as per specification no SS-AS/DLD |
| 21 | Providing & Fixing of printed instruction chart for (with minimum 700 x 1000 mm in size) treating persons suffering from electric shock, printed in English & Marathi and duly laminated complete. |
| 22 | Providing pair of duly tested rubber hand gloves as per IS :47705 suitable for working upto 22 kV supply complete. |
| 23 | Supplying and fixing standard first aid box with necessary antiseptic cream, medicine for use on wounds due burn, crepe bandage, gauge bandage, medicated ready to use bandage (Band-Aid) adhesive tape for medicinal use, scissors, antiseptic solution, etc. (All above contents shall be of standard makes) |
| 24 | Providing, erecting, testing & commissioning of 3.0MT Single Girder HOT crane for Lifting of Pumps including Cross MS Gantry, Corss Travel trolley, Vertical column of testing of I-Beam with concrete foundation, applying treatment to entire newly fabricated MS structure of Gantry etc. complete. |
| 25 | Dismantling -- Dismantling existing pole mounted distribution transformer safely without any damages. |
| 26 | Brackets (OH-BKT) - Supplying & erecting end pole D. P. Structure for 11/0.415 kV, 100 kVA Transformer with R.S.J. Pole 2 Nos. of size 100 x 116 mm x 11 Mtr. Long with suitable Distribution Box of C.R.C.A. Sheet 16 SWG with 4 Pole MCCB 200 Amps as incomer & 6 Nos.100 Amps Kitkat / MCCB for out going circuits. Transformer D.P. Structure includes the A. B. Switch 200 Amps, D.O. fuse Set & L.A. Set. 2 Nos.Top channel of size 100 mmx 50 mm for erection of A.B. Switch & 2 Nos. Base channel of size 100 mm x 50 x mm for erecting Transformer. Channel of size 75 x40 mm for erecting D.O. Fuse Set, L.A., A.B. Switch handle etc.Angle of size 50 x 50 x6 mm for erecting Distribution Box , Transformer Belt etc.as per drawing (min. 124 Kg. iron work ) with necessary clamps, Nut-bolts. V cross arm, top clip, insulators etc. complete with caution board & barbed wire. D.P. Structure shall be erected in c.c. foundation complete |
| 27 | Hermetically Sealed transformer (SS-TR-HSL) - Supplying, installing, testing & commissioning of 3 phase, 11/0.433 kV, 50 Hz., 100 kVA, Mineral oil immersed and naturally cooled outdoor type, aluminium wound, without gas cushioning, hermetically Sealed transformer, delta/star connected with additional neutral brought out on load side, temperature rise should not exceed 40? by thermometer in oil and 45? by the resistance method in winding at full load rating, using type A winding insulation (kraft paper) with HV tapping (with off load tap changer) off load +2.5 to -5 in steps of 2.5%, having 4 number of tap positions, with standard accessories complete with test certificate with losses below 475 Watts at 50% load, 1650 Watts at 100% load as per IS:1180 (part 1) : 2014 : 2021, with necessary permissions of Electrical Inspector, as per specification no SS- TR-HSL. |
| 28 | MCCB Panel Boards and Accessories (SW- MCCBPB)------------Providing & erecting floor/wall mounting, MCCB panel board with door, 1.2 mm thickness suitable for 3 pole incoming 250A, 4 ways 3 pole outgoing up to 100A MCCB on iron frame compliant to IEC 61439, as per specification no. SW-MCCBPB. (Excluding MCCBs) |
| 29 | LT - MCCBs (SW-MCCB) -------------- Providing & erecting 4 Pole MCCB 415V, 250A, rated short-circuit breaking capacity 36 kA (Ics=100% of Icu) adjustable thermal (overload) setting and adjustable magnetic setting with provided leads, provision for installation of shunt/UV/trip alarm contact. MCCB should have phase barriers both sides, with insulation withstand capacity 800V, no line-load bias in provided enclosure/panel as per specification no. SW-MCCB |
| 30 | Providing & erecting 4 Pole MCCB, 415V, up to 100A, rated short-circuit breaking capacity 25 kA (Ics=100% of Icu), adjustable thermal (overload) setting and fixed magnetic setting with provided leads, provision for installation of shunt/UV/trip alarm contact. MCCB with phase barriers on both sides, insulation withstand capacity 800V, no line-load bias in provided enclosure/panel as per specification no. SW-MCCB |
| 31 | Dismantling (WG-DM) - ---------------- Dismantling the existing light, fan, bell, clock, independent plug point, wiring including circuit mains of all types along with accessories etc. complete as per specification no. WG-DM/PW |
| 32 | Dismantling - Dismantling of existing fluorescent fittings of any type & size. |
| 33 | Point Wiring (WG-PW) ------------------ Point wiring for light/bell/exhaust fan in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories as per specification no. WG-PW/SW |
| 34 | Point wiring for independent plug in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories as per specification no. WG-PW/SW |
| 35 | Outdoor Fittings (FG-ODF) ------------ Supplying and erecting integrated LED street light fitting 70-75W IP65 & IK08 class having single piece pressure die-cast aluminium housing, having system lumens output of Min. 7700 Lumens, min. efficacy of 110 lumen/W, CRI>70, CCT upto 6500K,THD<10%, p.f. >0.95, operating range of 140-270V, inbuilt surge protection of 10 kV, Life class of 50,000 Hrs at L70B50 including driver complete with minimum 2 Years warranty as per specification No. FG-ODF/SL. |
| 36 | Accessories for Outdoor Fittings (FG-BKT) ----------------------- Supplying and erecting street light Wall bracket made from 40 mm. dia ‘B’ class G.I. pipe 1.2 m in total length complete as per specification no. FG-BKT/WB. |
| 37 | Lamps and Tubes for Indoor & Outdoor (FG-LP) ------------- Supplying & erecting ready to use Retrofit T8 LED, 18 / 20 watt tube light with polycarbonate body, heat sink, integrated HF electronic driver complete & compatible to T8 / T12 LED luminaire by disconnecting starter & ballast if necessary as per specification No. FG-LP/RET. |
| 38 | Fans (FG-FN) --------------- Supplying Pedestal fan 400 mm. 230 Volts 50 cycles oscillating type complete with guard and regulator 3 mtrs. of flexible wire and hand shield type 3 pin plug top. |
| 39 | Supplying and erecting Energy Saving Ceiling fan of 3 star rating as per BEE 230 V A.C. 50 cycles 1200 mm complete erected in position as per specification no. FG-FN/CF |
| 40 | Accessories for Fans (FG-FAS) -------------- Supplying and erecting fan hook of 10 mm. M.S. round bar grouted in RCC slab with making the site as original. |
| 41 | Fire Extinguishers -------------- Supplying & erecting Carbon Dioxide (CO2) fire extinguisher of 4.5 kg. capacity cartridge type conform to IS 2878 /15683 complete erected with necessary clamp made from 50 x 6 mm. M. S. flat with nut & bolts routed in wall complete. |
| 42 | Rebate for old damaged panel, cables 2 No. 30 HP VT pump set, 2 No. 30 HP motor, LT Panel, LT Cable, MS Pipes with Valves as is where is basis including dismantling at site neatly including all labour material tools etc along with transportation etc complete. |
| 43 | Sub Estimate ----------------Replacement of pumping Machineries along with allied works at WTP @ Kudal Industrial Area. Providing, installing, commissioning and testing of VERTICAL TURBINE, self water lubricated above floor type pump with VHS motor capable of discharging raw water at the rate of 286 Cum/ Hr. at the duty point head and operating at the bowl head of 40 Mtr. with 1450 rpm with IE2 1500 RPM (Synchronous Speed) Vertical solid shaft Totally Enclosed Fan Cooled squirrel cage induction motor conforming to IP-55, Continuously rated(S1) suitable for operation on 415V ± 10% volts, 3ph, 50 Hz ± 5%, combined variation 10%, AC supply ambient 50 deg.C with “F” Class Insulation with temp. rise limited to class “B” (75 deg C) altitude less than 1000m above m.s.l. Performance efficiency Values are conforming to IS 12615 / IEC 60034 of capacity to run the pump of minimum 45 KW / 60HP etc. complete with all accessories . Pump including stainless steel basket type strainer, bowl assembly, column assembly, discharge head , MS base plate of suitable size with minimum thickness of 24 mm, connecting stool etc. complete as per latest IS specifications. The 4 stage pumps with column pipes shall be manufactured from ERW pipes of 10 mm thick and each of maximum 1.5 m length provided with anticorrosive and special treatment paint and all line shafts impellers shafts of stainless steel AISI 410 and impeller should be of Bronze including 25 /30 mm M.S. sole plate and base frame of ISMB 300 x 150 mm with accurate standard 150 mm dia to read entire range of pressure gauge with necessary tubing and isolation cock. including all consumable materials, accurate digital type glycerin Pressure gauge to read entire range of pressure complete with necessary tubing. The complete pump assembly from strainer to discharge head shall have to be connected with stainless steel AISI-304, 316 nut bolts as per detailed specification and the pump operating at 1480 RPM including Component to be coated for VT pump, including providing required C.C. foundation, base channel, all allied material, cutting welding etc. complete. The pump should have Water Lubricated turbine pump complete with Bowl Assembly, Column Assembly, Discharge Head, PLT & Strainer and flat efficiency characteristics between operating range as per detail item specifications. Supplying, installing, commissioning and testing of 45 KW/ 60 HP vertical solid shaft totally enclosed fan cooled (TEFC) IP 55 type squirrel cage induction motor, suitable for operation on 415 +/- 10% volts, 3 phase, 50 cycles/ sec. (Hz), 1500 RPM (synchronous speed) AC supply having Performance efficiency at full load is 80% & confirming to IS 12615/IEC 60034 and power factor not less than 0.87 @ full load fitted with non-reversible ratchet arrangement and complete with top half clutch with 'F' class insulation with temp. rise limited to class 'B' (75 degree C) for ambient temp not exceeding 45 degree etc. complete. |
| 44 | Providing, installing, commissioning and testing of VERTICAL TURBINE, self water lubricated above floor type pump with VHS motor capable of discharging raw water at the rate of 429 Cum/ Hr. at the duty point head and operating at the bowl head of 21 Mtr. with 1450 rpm with IE2 1500 RPM (Synchronous Speed) Vertical solid shaft Totally Enclosed Fan Cooled squirrel cage induction motor conforming to IP-55, Continuously rated(S1) suitable for operation on 415V ± 10% volts, 3ph, 50 Hz ± 5%, combined variation 10%, AC supply ambient 50 deg.C with “F” Class Insulation with temp. rise limited to class “B” (75 deg C) altitude less than 1000m above m.s.l. Performance efficiency Values are conforming to IS 12615 / IEC 60034 of capacity to run the pump of minimum 37 KW / 50HP etc. complete with all accessories . Pump including stainless steel basket type strainer, bowl assembly, column assembly, discharge head , MS base plate of suitable size with minimum thickness of 24 mm, connecting stool etc. complete as per latest IS specifications. The 2 stage pumps with column pipes shall be manufactured from ERW pipes of 10 mm thick and each of maximum 1.5 m length provided with anticorrosive and special treatment paint and all line shafts impellers shafts of stainless steel AISI 410 and impeller should be of Bronze including 25 /30 mm M.S. sole plate and base frame of ISMB 300 x 150 mm with accurate standard 150 mm dia to read entire range of pressure gauge with necessary tubing and isolation cock. including all consumable materials, accurate digital type glycerin Pressure gauge to read entire range of pressure complete with necessary tubing. The complete pump assembly from strainer to discharge head shall have to be connected with stainless steel AISI-304, 316 nut bolts as per detailed specification and the pump operating at 1480 RPM including Component to be coated for VT pump, including providing required C.C. foundation, base channel, all allied material, cutting welding etc. complete. The pump should have Water Lubricated turbine pump complete with Bowl Assembly, Column Assembly, Discharge Head, PLT & Strainer and flat efficiency characteristics between operating range as per detail item specifications. Supplying, installing, commissioning and testing of 37 KW/ 50 HP vertical solid shaft totally enclosed fan cooled (TEFC) IP 55 type squirrel cage induction motor, suitable for operation on 415 +/- 10% volts, 3 phase, 50 cycles/ sec. (Hz), 1500 RPM (synchronous speed) AC supply having Performance efficiency at full load is 80% & confirming to IS 12615/IEC 60034 and power factor not less than 0.87 @ full load fitted with non-reversible ratchet arrangement and complete with top half clutch with 'F' class insulation with temp. rise limited to class 'B' (75 degree C) for ambient temp not exceeding 45 degree etc. complete. |
| 45 | Designing ,Providing, erecting, commissioning of LT Set switch gear FCMA Soft Starter panel along cubical type, MS sheet fabricated from 14 gauge CRCA sheet including all accessories, switch gear, Copper busbar, foundation channel this item includes Designing, providing, erecting, testing & commissioning of PLC cum FCMA starter without any active electronic component, moving parts & totally harmonics free, FCMA starter lifted with all accessories including providing & applying painting to frame with international orange colour & two doors & covers siemens gray etc. The starter shall be suitable for 50 HP induction motor operating at 415/440 Volts, 3 phase 50 Hz AC supply. The starter shall be flux compensated magnetic amplifier type (FCMA type). The details list of material required for L.T. Starter panel are mentioned in itemwise specification consist of material quantity and make.The main components of panel are 1 No. Incomer, 1 No. Changeover, 2 Outgoing Suitable for 2 No.x 60HP FCMA & 2 No. x 50HP FCMA Starter, Auxillary Feeder, Metering & Copper Bus Bar etc. complete. |
| 46 | Designing, Supplying, erecting ,testing & Commissioning of 100 KVAr APFC Panel including all accessories, switchgears, control wiring etc. complete. |
| 47 | Supplying erecting testing and commissioning DI D/F non-rising spindle soft seated glandless Gate Valves with body and bonnet of Ductile cast iron of grade GGG-40, wedge with fully encapsulated EPDM rubber (approved for drinking water ) and seals of NBR. The valves should be with replaceable stem nut and replaceable sliding shoes. Valve stems shall be of single piece thread rolled type. Valve shall have 3 “O” rings of NBR for stem sealing. Gate valve shall be compatible for buried application without valve chamber. Face-to- face dimensions as per BS 5163-89/IS 14846 – PD/EN 558 F4 and flange connections as per EN1092-2/IS 1538, Maximum valve operating torque should be at least 40% less than the torque as stated in the standard EN 1074. Electrostatic epoxy power / liquid coating (EP-P) inside and outside color blue RSL 5005 with minimum coating thickness of 250 microns. The EPDM rubber & Epoxy coating should be potable water certified. Material of construction :- Body, Bonnet :- Ductile Iron GGG40 (EN-JS-1030) Wedge, (Fully rubber encapsulated):- Ductile Iron GGG 40(EN-JS-1030) encapsulated with EPDM rubber- Portable water certified. Spindle / Stem: - SS: AISI 420 Stem Nut:- Brass Bonnet Gasket: - EPDM rubber potable water certified Internal fasteners: - Stainless Steel SS304 Stem Sealing :- Toroidal NBR sealing rings (Min 03 ‘O’ Rings) Coating: - Inside & Outside epoxy powder coated; DFT minimum 250 micron, shade RAL, shade RAL, 5005 (Signal Blue) potable water certified. excluding GST) 200 mm dia ,PN 1.6 rating |
| 48 | Providing, installing, commissioning & testing of 200 mm dia PN 1.6 Tilting Check Valve c/w Lever & Counter Weight, DI D/F slanted seat tilting disc swing check valve in single piece body. Body & disc. Of ductile cast Iron, shaft of stainless steel & bearing of zinc free bronze, Electrostatic epoxy powder / liquid coating inside & outside blue colour with minimum coating thickness of 150 micron. Complete with nuts, bolts, gaskets, washers etc. Suitable for pressure rating of 16 kg./ sq.cm. for seat without bypass arrangement as per detailed specifications complete including providing supporting CC block in M-150 grade concrete etc. complete. |
| 49 | Supplying erecting testing and commissioning DI D/F non-rising spindle soft seated glandless Gate Valves with body and bonnet of Ductile cast iron of grade GGG-40, wedge with fully encapsulated EPDM rubber (approved for drinking water ) and seals of NBR. The valves should be with replaceable stem nut and replaceable sliding shoes. Valve stems shall be of single piece thread rolled type. Valve shall have 3 “O” rings of NBR for stem sealing. Gate valve shall be compatible for buried application without valve chamber. Face-to- face dimensions as per BS 5163-89/IS 14846 – PD/EN 558 F4 and flange connections as per EN1092-2/IS 1538, Maximum valve operating torque should be at least 40% less than the torque as stated in the standard EN 1074. Electrostatic epoxy power / liquid coating (EP-P) inside and outside color blue RSL 5005 with minimum coating thickness of 250 microns. The EPDM rubber & Epoxy coating should be potable water certified. Material of construction :- Body, Bonnet :- Ductile Iron GGG40 (EN-JS-1030) Wedge, (Fully rubber encapsulated):- Ductile Iron GGG 40(EN-JS-1030) encapsulated with EPDM rubber- Portable water certified. Spindle / Stem: - SS: AISI 420 Stem Nut:- Brass Bonnet Gasket: - EPDM rubber potable water certified Internal fasteners: - Stainless Steel SS304 Stem Sealing :- Toroidal NBR sealing rings (Min 03 ‘O’ Rings) Coating: - Inside & Outside epoxy powder coated; DFT minimum 250 micron, shade RAL, shade RAL, 5005 (Signal Blue) potable water certified. excluding GST) 250 mm dia ,PN 1.6 rating |
| 50 | Providing, installing, commissioning & testing of 250 mm dia PN 1.6 Tilting Check Valve c/w Lever & Counter Weight, DI D/F slanted seat tilting disc swing check valve in single piece body. Body & disc. Of ductile cast Iron, shaft of stainless steel & bearing of zinc free bronze, Electrostatic epoxy powder / liquid coating inside & outside blue colour with minimum coating thickness of 150 micron. Complete with nuts, bolts, gaskets, washers etc. Suitable for pressure rating of 16 kg./ sq.cm. for seat without bypass arrangement as per detailed specifications complete including providing supporting CC block in M-150 grade concrete etc. complete. |
| 51 | Design ,Supply , Erection , Testing & commissioning of kinetic Air Valve DN 100 mm, including sluice valve PN 1.6 and its Operation Auto etc. complete. |
| 52 | Dismantling Joints------------------Providing, erecting and commissioning M.S. Dismantling joint as per requirement and Department's approved drawing and specifications, including machining and rubber rings and suitable for 16 kg/cm2 working pressure with required flanges of suitable size with nut bolts etc complete. The joint should have through long bolts so that during normal working pressure there should be no sliding movement of sliding flanges. L.O.F. ( length over flange ) should not be less than 75% of dia.--------------------PW 6-3) 200 mm dia Joint |
| 53 | Providing, erecting testing and commissioning at work site fabricated MS Pipes and specials with necessary circumferential and longitudinal joints with cutting, welding including cost of MS Pipes and flanges,nut bolts etc. with loading, unloading , transportation etc. complete. |
| 54 | Providing, Erecting &Commissioning of 400 mm dia. Full Bore Electromagnetic Flowmeters (EMF) As per ISO 4064, With accuracy +/0.5% of measured value & protection as per given specifications for Various Sizes including sensor, cable GI duct if suitable size for 25 mtrs ,including the pipe cutting , leveling and installation of flow meter in the pipelins with necessary tool tackles etc complete , as may be required at site & based on technical specifications .400mm diameter size flowmeter. |
| 55 | Supplying , Installation, Testing and Commissioning of Electro-Magnetic Flow Meter 200 MM Dia. along with all accessories Dismantling Joint, Cables, panels etc. complete |
| 56 | Providing flooring insulation for walk way and approach way etc. complete for Main LT Panel and control Panel area at PWW Kudal |
| 57 | Providing, erecting, testing & commissioning of 200KVA DG Set for Back up in WTP area including all allied works etc. complete. The item includes Foundations of DG Set, earthing, 2 run of LT Cabling with DWC Pipe enclosure , AMF Panel, Weather shed etc. complete. Permission from Electrical Inspector shall be obtained as per requirement. |
| 58 | Providing, erecting, testing & commissioning of 3.0MT Single Girder HOT crane for Lifting of Pumps including Cross MS Gantry, Corss Travel trolley, Vertical column of testing of I-Beam with concrete foundation, applying treatment to entire newly fabricated MS structure of Gantry etc. complete. |
| 59 | Providing and fixing 900mm high S.S.304 Grade Stainless steel railing with 40mm diameter and 1.5mm thick at top, 40mm diameter and 1.5mm thick vertical supports spaced at 1.5m center to center and 8mm thick toughened glass including fabricating ,fixtures, erecting , necessary welding , grinding , finishing, buffing to stainless steel pipe etc. complete. |
| 60 | Supplying , erecting, testing & commissioning of Turbidity Analyser(2 No.), PH measurement Transmitter Ph electrode(2 No.), Chlorine Analyzer(2 No.) with Ulatrsonic Cleaning system including calibration, cabling, sensor set, flow through Assembly, Universal Four wire Multichannel controller with indicator , excavation pipe installation, clamping power supply regulator, step down transformer, surge protector , power supply cable, switch board, electrification , conduiting, air valve, Stainer and including all satisfactory trial etc. complete. |
| 61 | Providing and fabricating structural steel work in rolled sections like joists, channels, angles, tees etc. as per detailed design and drawings or as directed including cutting, fabricating, hoisting, erecting, fixing in position making riveted / bolted /welded connections without connecting plates, braces etc. and including one coat of anticorrosive paint and over it two coats of oil painting of approved quality and shade etc. complete. |
| 62 | Accessories for Outdoor Fittings (FG-BKT)---------------Supplying and erecting street light Wall bracket made from 40 mm. dia ‘B’ class G.I. pipe 1.2 m in total length complete as per specification no. FG-BKT/WB. |
| 63 | Outdoor Fittings (FG-ODF)-----------------------Supplying and erecting integrated LED street light fitting 70-75W IP65 & IK08 class having single piece pressure die-cast aluminium housing, having system lumens output of Min. 7700 Lumens, min. efficacy of 110 lumen/W, CRI>70, CCT upto 6500K,THD<10%, p.f. >0.95, operating range of 140-270V, inbuilt surge protection of 10 kV, Life class of 50,000 Hrs at L70B50 including driver complete with minimum 2 Years warranty as per specification No. FG-ODF/SL. |
| 64 | Lamps and Tubes for Indoor & Outdoor (FG-LP)--------------Supplying & erecting ready to use Retrofit T8 LED, 18 / 20 watt tube light with polycarbonate body, heat sink, integrated HF electronic driver complete & compatible to T8 / T12 LED luminaire by disconnecting starter & ballast if necessary as per specification No. FG-LP/RET. |
| 65 | Dismantling------------------Dismantling existing pole mounted distribution transformer safely without any damages. |
| 66 | Brackets (OH-BKT)---------------Supplying & erecting end pole D. P. Structure for 11/0.415 kV, 200 kVA Transformer with R.S.J. Pole 2 Nos. of size 100mm x 116 mm x 11 m Long with suitable Distribution Box of C.R.C.A. Sheet 16 SWG with 4 Pole MCCB 400 Amps as incomer & 6 Nos.200 Amps Kitkat / MCCB for out going circuits. Transformer D.P. Structure includes the A. B. Switch 200 Amps, D.O. fuse Set & L.A. Set. 2 Nos.Top channel of size 100 mmx 50 mm for erection of A.B. Switch & 2 Nos. Base channel of size 100 mm x 50 x mm for erecting Transformer. Channel of size 75 x40 mm for erecting D.O. Fuse Set, L.A., A.B. Switch handle etc.Angle of size 50 x 50 x6 mm for erecting Distribution Box , Transformer Belt etc.as per drawing (min. 124 Kg. iron work ) with necessary clamps, Nut-bolts. V cross arm, top clip, insulators etc. complete with caution board & barbed wire. D.P. Structure shall be erected in c.c. foundation complete. |
| 67 | Hermetically Sealed transformer (SS-TR-HSL)-------------------Supplying, installing, testing & commissioning 3 phase, 11/0.433 kV, 50 Hz., 200 kVA, Mineral oil immersed and naturally cooled outdoor type, Copper wound, without gas cushioning, hermetically Sealed transformer, delta/star connected with additional neutral brought out on load side, temperature rise should not exceed 40? by thermometer in oil and 45? by the resistance method in winding at full load rating, using type A winding insulation (kraft paper), with HV tapping (with off load tap changer) off load +2.5 to -5 in steps of 2.5%, having 4 number of tap positions, with standard accessories complete with test certificate with losses below 780 Watts at 50% load, 2300 Watts at 100% load as per IS:1180 (part 1) : 2014, with necessary permissions of Electrical Inspector, as per specification no SS- TR-HSL. |
| 68 | Accessories------------------Supplying and erecting fencing of section having size at least 2450 mm in height from ground level and 1200 mm width with angle iron frame work erected in CC foundation and painted complete with provided earthing as per specification no. SS-AS/FSG |
| 69 | Supplying and erecting 50 x 50 x 6 mm angle iron as corner support 2.45m long fixed at the middle of the fencing frame and the other side inclined at 30 degree angle, in cement concrete foundation of 15 x 15 x 40 cm complete duly painted with one coat of red oxide and two coats aluminium paint complete. |
| 70 | Supplying and erecting double leaf hinged door each 1500 mm in width x 2450 mm in height using B class GI pipe, hinges and angle iron supports, chain link wire mesh (jali) complete supported on channel iron, erected in foundation and painted complete as per specification no SS-AS/DLD |
| 71 | Providing & Fixing of printed instruction chart for (with minimum 700 x 1000 mm in size) treating persons suffering from electric shock, printed in English & Marathi and duly laminated complete. |
| 72 | Providing pair of duly tested rubber hand gloves as per IS :47705 suitable for working upto 22 kV supply complete. |
| 73 | Dismantling (WG-DM)----------------Dismantling the existing light, fan, bell, clock, independent plug point, wiring including circuit mains of all types along with accessories etc. complete as per specification no. WG-DM/PW |
| 74 | Point Wiring (WG-PW)-------------------Point wiring for light/bell/exhaust fan in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories as per specification no. WG-PW/SW |
| 75 | Point wiring for independent plug in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories as per specification no. WG-PW/SW |
| 76 | Fans (FG-FN)-------------Supplying Pedestal fan 400 mm. 230 Volts 50 cycles oscillating type complete with guard and regulator 3 mtrs. of flexible wire and hand shield type 3 pin plug top. |
| 77 | Supplying and erecting Energy Saving Ceiling fan of 3 star rating as per BEE 230 V A.C. 50 cycles 1200 mm complete erected in position as per specification no. FG-FN/CF |
| 78 | LT Cables (Aluminum) (CB-LT/AL)-----------------Supplying, erecting & terminating FR XLPE insulated, galvanised steel wire armoured (round) cable, 1100 V 4 core 6 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL |
| 79 | Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable, 1100 V 4 core 120 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL |
| 80 | Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable, 1100 V 4 core 185 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL |
| 81 | Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable, 1100 V 4 core 25 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL |
| 82 | Cable Enclosures (CB-CE)-----------------Supplying and laying (including excavation of suitable width & depth up to 90 cm) 50 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, complete. |
| 83 | Cable Tray (CB-CT) --------------Providing & erecting hot dipped galvanised ladder type cable tray manufactured from 16 SWG GI sheet of 300 mm width & 100 mm height with required standard accessories. |
| 84 | Dismantling----------------------Dismantling of existing fluorescent fittings of any type & size. |
| 85 | Accessories for Fans (FG-FAS) -------------------Supplying and erecting fan hook of 10 mm. M.S. round bar grouted in RCC slab with making the site as original. |
| 86 | Plate, Pipe type Earthing (EA-EP)--------------------Supplying, installing and testing earthing with copper earth plate size 60 x 60 x 0.315 cm with funnel with a wire mesh for watering and brick masonry block C.l. cover with minimum 25 kg Carbon based environment friendly back fill ground ehancing compound complete with all accesories of copper materials & recording the results as per specification no EA-EP/EF |
| 87 | MCCB Panel Boards and Accessories (SW- MCCBPB)-----------------------Providing & erecting floor/wall mounting, MCCB panel board with door, 1.2 mm thickness suitable for 3 pole incoming 250A, 4 ways 3 pole outgoing up to 100A MCCB on iron frame compliant to IEC 61439, as per specification no. SW-MCCBPB. (Excluding MCCBs) |
| 88 | LT - MCCBs (SW-MCCB)----------------------Providing & erecting 4 Pole MCCB, 415V, up to 100A, rated short-circuit breaking capacity 25 kA (Ics=100% of Icu), adjustable thermal (overload) setting and fixed magnetic setting with provided leads, provision for installation of shunt/UV/trip alarm contact. MCCB with phase barriers on both sides, insulation withstand capacity 800V, no line-load bias in provided enclosure/panel as per specification no. SW-MCCB |
| 89 | Fire Extinguishers-------------------------Supplying & erecting Carbon Dioxide (CO2) fire extinguisher of 4.5 kg. capacity cartridge type conform to IS 2878 /15683 complete erected with necessary clamp made from 50 x 6 mm. M. S. flat with nut & bolts routed in wall complete. |
| 90 | Rebate for old damaged panel, cables , 2 No. 40HP & 2 No. 30 HP VT pump set, 2 No. 40HP & 2 No. 30 HP motor, LT Panel, LT Cable, MS Pipes with Valves as is where is basis including dismantling at site neatly including all labour material tools etc along with transportation etc complete. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 06, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 31, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 19 daysSep 02, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 21 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender