Tender For Maintenance Of Sewer Network And Periodical Services Of Accns In Pallanwala Mil Stn And Its Outstations Under Ge (S) Akhnoor.
Tender Value
30 Lakhs
Estimated cost
Bid Submission
27 Aug 2026
3 days left
EMD
60000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jammu → Jammu and Kashmir
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Maintenance Of Sewer Network And Periodical Services Of Accns In Pallanwala Mil Stn And Its Outstations Under Ge (S) Akhnoor.
BOQ
| Sl. No. | Item Description |
| 1 | M&L for preparation of old plastered or unplastered surfaces of ceiling and applying one coat of white wash, complete all as specified and as directed. |
| 2 | M&L for preparation of old plastered or unplastered surfaces of wall and applying one coat of Exterior Emulsion paint, complete all as specifed and as diretced. |
| 3 | M&L for preparation of old plastered or new plastered surfaces of wall and applying one coat of primer over two coats of wall care putty, including preparation of surfaces/grinding of surface as required before applying any paint or oil emulsion, complete all as specifed and as diretced. |
| 4 | M&L for preparation of old painted wooden surfaces of any description, not otherwise described, over 10cm width or girth including and applying one coat of synthetic enamel paint, complete all as specified and as directed by Engineer-In-Charge. |
| 5 | M&L for preparation of old painted steel surfaces of any description, not otherwise described, over 10cm width or girth and applying one coat (finishing coat) of synthetic enamel paint, complete all as specified and as directed. |
| 6 | Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, complete all as specified and as directed. |
| 7 | M&L for brick work with sub class 'B' bricks old size straight or curved in plan exc 6m mean radius built in cement mortar 1:6, complete all as specified and directed. |
| 8 | Description all as per Serial item No. 7 here in befoe but except bricks, complete all as specified and directed. |
| 9 | Taking down cement plaster on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed. |
| 10 | M&L for rendering 10 mm thick in cement mortar 1:6 on any surfaces of brick work or concrete surfaces, finished even & smooth without using extra cement, complete all specified and directed. |
| 11 | M&L for rendering 15 mm thick in cement mortar 1:4 on fair faces of brick work or concrete surfaces, finished even & smooth without using extra cement, complete all specified and directed. |
| 12 | M&L for preparation of new plastered or unplastered surfaces of walls and applying two coats of oil bound distemper over a primer coat of chalk whitening, complete all as specified and as directed. |
| 13 | M&L for preparation of new plastered or unplastered surfaces of walls and applying two coats of cement based paint over primer coat, complete all as specified and as directed. |
| 14 | S&F for pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified & directed including dismantling of AC sheet, complete all specified and directed. |
| 15 | S&F for pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws, including dismantling of AC sheet, complete all specified and directed. |
| 16 | Providing and fixing ceiling board of 4mm thick, designer, in ceiling fixed as per manufacturer’s instructions, including powder coated galvanised iron snap grid frame work of main and tee (weight not less than 240gm/Rm), angle (weight not less than 217 gm/Rm), grid size 595x595mm, for false ceiling all as specified, and hangers 6mm dia, galvanised iron (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of galvanised iron wire of 4.0mm dia, length as required at site and expansion hold fasteners 12.50mm dia, 40mm long inclding dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets, any thickness, including cover fillets, complete all as specified and as directed . |
| 17 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and as directed. |
| 18 | M&L for glazed ceramic jointless tiles in vertical surface/ dado, size 300x450x7mm thick, set and jointed in neat cement slurry and pointed in white or colour cement to match, the shade/ colour of tiles including laid over 10mm thick rendering in cement mortar 1:4, complete all as specified and as directed. |
| 19 | M&L for non-skid, coloured, ceramic tiles 7 to 8 mm thick of size 400x400mm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and laid over and including screed bed or bedding layer of mortar 15mm thick in cement mortar 1:6, complete all as specified and as directed. |
| 20 | M&L for non-skid, coloured, ceramic tiles 7 to 8 mm thick of size 600x600mm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and laid over and including screed bed or bedding layer of mortar 15mm thick in cement mortar 1:6, complete all as specified and as directed. |
| 21 | M&L for non-skid, coloured, ceramic tiles 7 to 8 mm thick of size 600x600mm, set and fixing in skirting/ dado or any other vertical surfaces and pointed in white or coloured cement to match and including 10mm thick rendering in cement mortar 1:4, complete all as specified and as directed. |
| 22 | Demolition of (un-reinforced) cement concrete in ground floors and pavings not exceeding 15cm thickness (below or above ground level), including cleaning, removal and disposal of rubbish/ waste materials from premises, complete all as specified and as directed. |
| 23 | M&L for 25mm thick plain cement concrete in sub bases, floors type B-1, 1:2:4 (20mm graded aggregate), finishing concrete surface even and fair without using extra cement, complete all as specifed and directed. |
| 24 | M&L for plain cement concrete 1:2:4, type B-1, (using 20mm graded crushed stone aggregate), nominal mix, as in copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, including necessary form work, complete all as specified and as directed . |
| 25 | Taking down of chowkhats or frame with shutters (without taking off shutters from the frames) area not exceeding 1.50 Sqm each, complete all as specified and as directed by Engineer-In-Charge. |
| 26 | Taking down of chowkhats or frame with shutters (without taking off shutters from the frames) area exceeding 1.50 Sqm but not exceeding 4.0 Sqm each, complete all as specified and as directed by Engineer-In-Charge. |
| 27 | Taking down shutters of any descriptions area exceeding 1.00 Sqm but not exceeding 2.00 Sqm, complete all as specified and directed by Engineer-In-Charge. |
| 28 | S&F in repair door closer, aluminium extruded body section, hydraulically regulated, designation No-01, universal type, suitable for door shutters up to 700mm in width and of weight not more than 35 kg, complete all as specified and as directed by Engineer-In-Charge. |
| 29 | M&L for mild steel framed work such as in grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; staging for of water tanks, cooler stand and similar work conforming to Fe-290, Gde-E-165, including cutting and welding complete all as specified and as directed by Engineer-In-Charge.Note:- Demolition of existing brick staging shall be measured under Serial Item No.06 of BOQ. |
| 30 | M&L for preparation of old decorated plastered or un plastered surface of walls, making surface even by filling putty in small holes, cavaties, cracks and applying one coat of oil bound distemper (any tint), complete all as specified and as directed by Engineer-In-Charge. |
| 31 | M&L for pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., size of frame 125x60mm, complete all as specified and as directed by Engineer-In-Charge. |
| 32 | M&L for pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., size of frame 105x60mm, complete all as specified and as directed by Engineer-In-Charge. |
| 33 | S&F for plain framed, paneled shutter (two panel) 35mm thick, 2nd class soft wood with lock rail and panel of 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS:1003 (Part-I), kiln seasoned and chemically pressure treated, complete all as specified and as directed by Engineer-In-Charge. |
| 34 | S&F for 40 mm thick flush shutter prepared to receive glass/ wire cloth, etc. (in 2 panels n. exc 0.4 sqm each) with sash bars, solid core construction, with block board core and plywood face panels, commercial type on both sides with both faces covered with decorative face veneer with lipping/frame , including stainless steel wire cloth, 0.46mm nominal dia of wire and average width of aperture 1.18mm etc.; supplied and fitted to chowkhats, complete all as specified and as directed by Engineer-In-Charge. |
| 35 | S&F for aluminium powder coated (minimum thickness of powder coating 50micron) frame for window, ventilator with one or more rebates including joining cleat for fixing etc, complete all as specified and as directed by Engineer-In-Charge. |
| 36 | S&F for aluminium powder coated aluminium window ( including glazed and skelton shutter ) and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips,rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.)suitable handle (1 no.) (thickness of powder coating should not less than 50 micron), complete all as specified and as directed by Engineer-In-Charge. Please Enable Macros to View BoQ information |
| 37 | S&F for aluminium powder coated aluminium window ( including glazed and skelton shutter ) and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips,rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.)suitable handle (1 no.) (thickness of powder coating should not less than 50 micron), complete all as specified and as directed by Engineer-In-Charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 06, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 27, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 3 daysSep 04, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 11 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender