Tender For Special Repairs To Dsc Jcos In-Living Accommodation (G + 2 Block) Building At Naval Dockyard, Visakhapatnam Under Ge (I) Dm, Visakhapatnam.
Tender Value
71.16 Lakhs
Estimated cost
Bid Submission
02 Sep 2026
25 days left
EMD
1.31 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Visakhapatanam → Andhra Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repairs To Dsc Jcos In-Living Accommodation (G + 2 Block) Building At Naval Dockyard, Visakhapatnam Under Ge (I) Dm, Visakhapatnam.
BOQ
| Sl. No. | Item Description |
| 1 | [SCHEDULE 'A' PART-I [B/R WORKS] |
| 2 | Demolition of textile covering and including all padding concrete over RCC slab over roof removing rubbish off the premises complete all as specified and directed. |
| 3 | M&L for providing, cement concrete type B1 1:2:4 (Using 20mm graded stone aggregate) as in roof padding concrete and kerbs or mud stops, rounded or chamfered on edges complete all as specified and directed. |
| 4 | M&L for 10mm thick screed bed over padding concrete cement mortar 1:4 with water proofing compound as per manufacture instructions by weight of cement and finish the surface even and smooth with out using extra cement complete all as specified and directed.Note :- Supply only WPC will be measured and paid separately |
| 5 | M&L for applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.20 kg per Sqm including cleaning of surfaces all as specified and directed. |
| 6 | M&L for APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (Weight not less than 150 gms/sqm) shall be laid over entire roof surface and on vertical surface up to groves with other laps of 100mm. The over lap shall be sealed by flames finished with one coat of aluminium paint @0.10kg/sqm complete all as specified and directed. |
| 7 | M&L for applying one coat of aluminium paint @ 0.10 kg/sqm incl preparation of surfaces complete all as specified and directed. |
| 8 | Dismantling floor, hearth or wall tiling or stone slabs of any description and in any postion including cement mortar bedding (but not backing), removing and rubbish off the MD land complete all as specfied and directed |
| 9 | Demolition of cement concrete of any description and in any position not otherwise specifically provided complete all as specified and directed. |
| 10 | M&L for 25 mm thick cement concrete type 'B-0' 1:2:4 using 12.5mm graded stone aggregate as in flooring all as specified and directed. |
| 11 | M&L for Light shade vitrified ceramic tiles 8 to 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over 15mm thick cement mortor (1:6) screed bed complete all as specified and directed. |
| 12 | M&L light shade vitrified ceramic tiles 10 mm thick (square/ rectangular) polished as in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10 mm thick 1:4 cement morter complete all as specified and as directed |
| 13 | Material & labour for coloured Non - skid ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed inneat cement slurry and pointed in white or coloured cement to match laid over and including cement screed 15 mm thick in 1:6 complete all as specified and as directed. |
| 14 | M & L for coloured glazed ceramic tiles 350 x 250 x 7 mm /450X300X7/8 mm thick in dado set and jointed in neat cement slurry and pointed in coloured cement to match fixed over including rendering in CM 1:4, 10mm thick all as specified and directed. |
| 15 | Taking down chowkats or frames not exceeding 1.5 Sqm each (Without taking off shutters from the frame) and removing away from site complete all as specified and directed. |
| 16 | Taking down Chowkats or frames exceeding 1.5 Sqm but not exc 4.00 Sqm each (Without taking off shutters from the frame) and removing away from site complete all as specified and directed. |
| 17 | S&F factory made solid PVC door frame of size 50 mm x 47 mm made out of 5mm thick plain colour PVC sheet reinforced MS square tube, supplying & fixing in opening as per specification & drawing on page no. 178 of SSR Part -II complete all as specified and directed. |
| 18 | S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. square tube for top and bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip 20 mm wide stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in M.S. frame welded /sealed to the stiles and rails with suitable sheet beading, and jointed together with solvent cement, supplying & fixing in the frame at site as per specification and drawing of page no 174 of SSR Part -II complete all as specified and directed. |
| 19 | S&F 75 mm butt hinges heavy weight cold rolled mild steel and fixed complete all as specified and directed. |
| 20 | S&F 150 mm aluminium anodised barrell tower bolts of extruded section and fixed complete all as specified and directed. |
| 21 | S&F extruded aluminium alloy handles 125 mm long fabricated type anodised complete all as specified and directed . |
| 22 | S&F plain, solid, 2nd hard wood class straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with the glue pinned at joints as in doors and windows with 2nd class hardwood complete all as specified and directed. |
| 23 | S&F bands, straps, supports or stays for rainwater, ventilating pipes,including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed. |
| 24 | S&F 30mm thick moulded beed is provided and planted round panels, panelled shutters (any number of panels), 1st class softwood with, or of veneered particle board medium density, wood particle board with commercial face veneers boards on both side with lipping/frame to match a supplied and fitted to chowkats all as specified and directed. |
| 25 | S&F 150mm floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed. |
| 26 | S&F 100 mm butt hinges heavy weight cold rolled mild steel and fixed complete all as specified and directed. |
| 27 | S&F aluminium alloy sliding door bolt 250 mm long with hasp and staple and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast alumimnium alloy and fixed complete all as specified and directed. |
| 28 | S&F 150 mm aluminium anodised barrell tower bolts of extruded section and fixed complete all as specified and directed. |
| 29 | S&F 150 mm extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed. |
| 30 | Providing and fixing factory made UPVC white colour sliding window exceeding 2.00 Sqm. Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mmx52mm), sliding sash (42mmx67mm). Sliding mesh sash (42mmx57mm), sliding interlock (One vertical length in each shutters) (45.5mmx28mm), Glazing bead (24.5mmx16mm) will be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc. making arrangement for fixing of hardware. EPDM gasket, 1.2 +, - 0.2mm thick galvanised steel frame (30mmx18mm) 2 Nos, sliding sash (30mmx18mm), sliding mesh sash(26mmx10mm) profile to be inserted in required profile,frame will be fixed to the wall with 8 mmx100mm long fasteners, Hardware (touch lock of zinc alloyed (white powder coated), steel roller system. Stainlesssteel wire cloth 0.36mm nominal dia of wire and average width of aprature 1.40mm and required accessories complete.Note :- The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose |
| 31 | S&F anodised aluminium DG-102 (anodised transperent or dyed to require shade according to IS 1868 with minimum anodic coaing of grade AC -15) of approved design / pattern , with approved standered scetion and fixed to the existing window frame with CP brass /stainless steel screw @200 mm ceneter to center ,WT 225gm/square feet including cutting the gril to propre opening size for fixig and operation of hanmdles and fixing approvedanodised aluminum stanedre scetion around the openings , all comete as per requirement and direction of Engr-in- Charge. |
| 32 | M&L for sheet glass 4.8mm thick, ordinary quality and glazing with oil putty in sqaure not exc 0.5sqm in each pane complete all as specified and directed. |
| 33 | Supply and fixing factory made UPVC white colour fixed glazed window/ ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to UPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. Note :- Glass shall be paid separately |
| 34 | S&F 5mm thick figured glass, pin head type and glazing with oil putty in squares not exc 0.5 sq. m in each pane complete all as specified and directed. |
| 35 | Demolition of stone slabs and tiles of any description or thicknes in floors, aprons etc laid bedded and pointed in any mortar complete all as specified and directed. |
| 36 | M&L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking plat forms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admix ture of pigment to match with shade of granite including round edging and marking anti skid cutting lines with cutters on treads, complete all as specified and directed. |
| 37 | M&L for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and as directed. |
| 38 | Dismantling water tanks of capacity exc 1000 Ltr but not exc 2000 Ltr and removing to store complete all as specified and directed. |
| 39 | S&F rotational moulded polythylene water storage tanks 2000 ltrs capacity (cylindrical or vertical with closed top) hoisted and fixed in position, complete all as specified and directed. |
| 40 | Supply & fix brass ball valve 25 mm dia high pressure with polythene float and flynut complete including taking down old one all as specified and as directed |
| 41 | S&F in repair of 0.63mm mild steel, plain, black sheet in wall cladding, crumple joint, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and directed. |
| 42 | Demoliton brick work or stone masonry built in cement mortar including all quoins, arches, pillars etc and removing the debries to a distance 5km away from the Dockyard premises all as specified and directed. |
| 43 | M&L for Pre cast cement concrete type 1:3:6 type C-1 (20mm graded stone aggregate) block masonry with solid blocks exc 10 cm in width and setting in cement mortar 1:4 complete all as specified and directed. |
| 44 | Dismantling wrought iron or mild steel work of any description not otherwise provided complete all as specified and directed. |
| 45 | M&L for structural steel work as in roof truss (framed), trussed, purlins, rails and fastenings and heavy bracket framing (Beam, Tee, Angle, Channel or flat sectios) including distance pieces, cleats etc.confirming to Fe-410-W(Gde-E-250) quality A complite all ss specified and directed. |
| 46 | Taking down rain water or soil pipes or PVC pipes including all fittings any size and pattern complete all as specified and directed. |
| 47 | S&F 160 mm dia PVC (SWR) pipes single, socketed, in any length with rubber ring joints fixed to wall complete all as specified and directed |
| 48 | S&F 160 mm bore PVC (SWR) bends (any radius) with oval access door complete all as specified and directed. |
| 49 | S&F 160 mm bore PVC (SWR) junction single, (Single T) equal or unequal with oval access door complete all as specified and directed.PVC (SWR) |
| 50 | M&L 40 mm dia High density polyethylene (HDPE ) pipe of pressure rating 6 Kg /Sq.cm as in waste pipe (Short Length) fixed to wash hand basin waste etc complete to floor including taking out old one all as specified and as directed |
| 51 | Dismantling Galvalume aluminium zinc coating ( corrugated or semi corrugated ) sheets, in roof covering complete all as specified and directed. |
| 52 | S&F pre painted galvalume aluminium zinc coating GI based corrugated/ semi corrugated, tripizoidal or any profilesteel sheet 0.50mm thick of an labour having tensile strength of 550 MPA as in roof covering/cladding to wall fixed with self traping screw complete all as specified and directed. |
| 53 | S&F in repair vitreous China Wash Basin, white, flat back of size 550 x 400 mm including suitable size of CI brackets, brass chromium plated waste fittings 32 mm dia with long screw shanks and fly nuts, flange and bedded in red lead cement complete all as specified and directed including taking out old one. |
| 54 | S&F in repair 15 mm dia pillar taps, cast copper alloy with capstan head/swan type, chromium plated, screwed down, high pressure with or without letter 'Hot' or Cold' with long screwed shanks and fly nuts screwed for iron pipes including taking out old one complete complete all as specified and directed |
| 55 | S&F in repair 15 mm dia bib taps, cast copper alloy fancy type, chromium plated with crutch or butterfly handle, screwed down screwed for iron pipe of for brass ferrule including taking down old onecomplete all as specified and directed |
| 56 | S & F in repair health faucet 15 mm bore brass chromium plated jet spray with CP pipe of 900 mm long and connector all as specified and directed. |
| 57 | S&F in repair 10 Ltr capacity PVC valveless syphonic action type flushing cistern low level white, with inlet, ball valve, float and handle including PVC flush pipe and brackets complete fixed in wall and floor to trap of WC as required including taking down old one complete all as specified and directed. |
| 58 | S&F in repairs vitreous China wash down water closet pan (pedestal pattern) white excluding fixing bolts, flushing cistern and flush pipe including taking out the existing unserviceable pedestal pan complete all as specified and directed. |
| 59 | S&F in repair 15 mm dia PVC connections, 600 mm long with PTMT nuts of suitable size at two end complete all as specified and directed |
| 60 | S&F in repair 15 mm dia PVC connections, 450 mm long with PTMT nuts of suitable size at two end complete all as specified and directed |
| 61 | S&F in repair tubular towel rail 20 mm dia brass chromium plated 'D' type 60 cm long between flange brass CP including taking down old one all as specified and directed. |
| 62 | S & F in repairs fancy type chromium plated 15 mm bore Stop valves, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed. |
| 63 | S&F 125 mm size brass chromium plated shower rose fixed to steel pipe or union complete including taking out old one all as specified and directed. |
| 64 | S & F 20 mm dia Gun Metal, globe or Gate Valve with Iron wheel head Screwed both ends for Iron Pipe complete all as specified and directed. |
| 65 | S&F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long all as specified and directed. |
| 66 | M & L 75 mm bore PVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified and directed. |
| 67 | S&F in repairs 600mm x 450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. |
| 68 | S & F in repairs angular stop cock (Fancy type chromium plated) 15 mm bore , cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed. |
| 69 | Taking up or down 15 mm bore steel water tubing and connections including cleaning for refixing or removal complete all as specified and directed. |
| 70 | Taking up or down 20 mm bore steel water tubing and connections including cleaning for refixing or removal complete all as specified and directed. |
| 71 | Taking up or down 25 mm bore steel water tubing and connections including cleaning for refixing or removal complete all as specified and directed. |
| 72 | S&F 15 mm dia (outer diameter of the pipe) Unplasticised PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe complete all as specified and directed. |
| 73 | S&F 20 mm dia (outer diameter of the pipe) Unplasticised PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe complete all as specified and directed. |
| 74 | S&F 25 mm dia (outer diameter of the pipe) Unplasticised PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe complete all as specified and directed. |
| 75 | Cutting chases, pinning in stone, concrete block or slab wall, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting exceeding 20cm girth in brick walls complete all as specified and directed. |
| 76 | Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) as in Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and directed. |
| 77 | M&L reinforced cement concrete type B1 (1:2:4) 20mm graded aggregate in walls, retaining walls, basement walls, ballast walls,fin wall and the like; any thickness; above top of footings; including attached pilaster and buttresses complete all as specified and directed. |
| 78 | M&L for Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 79 | M&L for formwork to edges of concrete flats, breaks in floors, openings in concrete walls, floors and roofs and sides of RCC/PCC bands in walls, horizontal or sloping, and similar work all exceeding 20cm wide. (Where RCC/PCC band in walls, spanning and opening, the formwork soffit complete all as specified and directed. |
| 80 | Material & labour for chipping (20mm to 50mm) of existing damaged, spalled & loose portion of concrete of the RCC members completely till the reinforcement is exposed and sound concrete is observed by using mechanical means and manual chisels and further the surface is cleaned with water jet, again clean the surface with blower to remove all loose fine particles present in the surfaces complete all as specified and directed. |
| 81 | M&L for preparation of exposed of rusted steel reinforcement with metal wire brush , cleaning the rusted surfaces free from loose rust and application of rust remover cum passivator with brush to the rusted reinforcement , and removing rust with flex after 24 hours of application of rust remover with the help of wire brush, sand paper and thoroughly washed with water with the help of pressure jet and allowing it to dry complete all as specified and directed. Note: Area of cleaned reinforcement steel bar shall be measured for payment. |
| 82 | M&L for preparation of surfaces of steel of reinforcement by cleaning and providing, mixing and applying zinc anti-rust agent as per manufacturers method of application to rebar corrosion protection system to reinforcement Fosroc or equivalent in M/S Sika India Pvt. Ltd. / M / S Choksey Chemicals Pvt. Ltd. / M/S Mapei Const Product India Pvt Ltd. / M/S THermax Ltd / M/S STP / M/S Dr Sunanada / M/S BASFor any other approved manufacturer of E-in-C's branch @3.75Kg/Sqm surface of steel reinforcement in two coats complete all as specified and directed. |
| 83 | M&L for applying a coat of Polymer modified cementious bonding coat on the concrete surfaces with one part of Styrene Butadiene Rubber latex emulsion (SBR latex) manufactured by M/s Fosroc chemicals or equivalent in M/S Sika India Pvt. Ltd. / M / S Choksey Chemicals Pvt. Ltd. / M/S Mapei Const Product India Pvt Ltd. / M/S THermax Ltd / M/S STP / M/S Dr Sunanada / M/S BASFor any other approved manufacturer of E-in-C's branch with four parts of water and six parts of cement by weight. Coverage of SBR latex-0.25Ltr / sqm for one coat complete all as specified and directed. |
| 84 | M&L for providing Shear connectors and Anchoring by drilling 16 mm dia holes up to depth of 100mm in concrete surfaces and fixing 10 mm dia TMT bars L shaped anchor rods as shear connectors by using Fosroc Lokfix chemical or any other equilent make as approved by GE (Mix of base and hardener of the polyester resin) in defective concrete area of the slab / column / beams / chajjas / lintel etc or any other structural member as per site requirement after cleaning the drilled hole by using water jet and after drying clean the surface with blower to remove all loose fine particles present in the hole. The Mix of base and hardener of the polyester resin shall be prepared by thorough mixing of base & hardener by the help of spatula. After preparing the mix the holes shall be filled to a minimum depth of 1/3rd of the hole with the prepared polyester resin and the reinforced bar shall be inserted to full depth of hole and extra length of the reinforcement bar shall be bent into the concrete to maintain proper cover to the reinforcement complete all as specified and directed. |
| 85 | M&L for applying polymer modified, cementitious mortar fibre reinforced, single component shrinkage controlled, (Renderoc SP40 of Fosroc Makeor equivalent in M/S Sika India Pvt. Ltd. / M / S Choksey Chemicals Pvt. Ltd. / M/S Mapei Const Product India Pvt Ltd. / M/S THermax Ltd / M/S STP / M/S Dr Sunanada / M/S BASFor any other approved manufacturer of E-in-C's branch having a compressive strength of 40 MPA strength for reparing of RCC members like columns, Beams / Slab soffits incl necessary formwork etc. complete all as specified and directed. |
| 86 | M&L for application of polymer modified reinstatement mortar 20mm thick in isolated places of repair works of RCC members with Rendroc S2 of M/s Fosroc make or equivalent in M/S Sika India Pvt. Ltd. / M / S Choksey Chemicals Pvt. Ltd. / M/S Mapei Const Product India Pvt Ltd. / M/S THermax Ltd / M/S STP / M/S Dr Sunanada / M/S BASFor any other approved manufacturer of E-in-C's branch having a compressive strength of 40 MPa complete all as specified and directed. |
| 87 | Providing double steel scaffolding for the outer surfaces of the building to provide platform to the workmen complete all as specfied and directed.Note : The superficial area of the building cover is measured for payment |
| 88 | Taking down cement plaster on brick or concrete wall etc including racking out joint hacking for key, scrubbing down with water etc. complete all as specified and as directed. |
| 89 | M&L for 10 mm thick rendering in cement mortar (1:6) on brick or concrete surfaces and finishing the surfaces even and smooth without using extra cement complete all as specified and directed. |
| 90 | M&L for rendering 15 mm thick in CM (1:4) on fair faces of brick work or concrete surfaces and finishing the surface even and smooth with out using extra cement and using WPC at the rate of 3% by weigth of cement all as specified and directed. |
| 91 | M&L for 5 mm thick plastering in cement mortar 1:3 on concrete surfaces of ceiling and finishing the surfaces fair and even without using extra cement all as specified and directed. |
| 92 | Supply only integral water proofing compound all as specified and directed. |
| 93 | M&L for preparing newly plastered and unplastered surfaces of ceiling and applying three coats of white washing complete all as specified and directed. |
| 94 | M&L for preparation of new plastered surface of wall and applying two coats of oil bound distemper over a one coat of alkali resistant primer with 1mm thick wall care putty over plastered surface to prepare surface even and smooth complete all as specified & directed. |
| 95 | M & L for preparation of newly plastered surfaces of walls and applying two or more coats of 100% premium acrylic paint having VOC less than 50 gm/litre and UV resistance a per IS 15489:2004, Alkali & fungal resistance, dirt resistance ecterior paint of required shade 9company depot tinted with silicon additives @ 1.43 litre/10 sqm over and including priming coat of exterior promer applied @ 0.9 litre/10 sqm over new surfaces complete all as specified and directed. |
| 96 | Complete removal of existing treatment of old decorated surfaces of walls and applying two coats of oil emulsion distemper over a coat of alkali resistant primer over two coats of cement based white wall putty of minimum thick ness 1.5 mm (in two coats) and cutting to smooth surfaces by sand paper complete all as specified & directed. |
| 97 | Complete removal of existing treatment on walls and for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm over new surfaces with one coat of birla putty complete all as specified and directed. |
| 98 | M&L for preparation of new or previously untreated steel and iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed. |
| 99 | M&L preparation of new or previously untreated wooden surface of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 100 | Cutting of sapings of any size from buildings in any situation & at any height incl removal of roots from walls incl applying root killer chemicals as per maunfactures instruction and making good disturbed portion with PCC 1:2:4 type B0 (using 12.5mm graded stone aggregate) complete finish with cement mortar (1:4) as specification and as directed. |
| 101 | S&F in repair precast cement concrete louvres and jallies, 25mm thick (measured solid) type B0 (1:2:4 using 12.5mm stone aggregate) set in cement mortar 1:4 , including all mould- ings but excluding frame all as specified and directed.Note :- Pre cast frame shall be measured separately. |
| 102 | Demolition of cement concrete in ground floor and paving not exc 15cm thick complete all as specified and directed. |
| 103 | M&L for cement concrete type D2 1:4:8 (40 mm graded aggregate) as in foundation filling and mass concrete all as specified and directed. |
| 104 | M&L for 100mm thick Cement concrete type B-2, 1:2:4 (40mm graded aggregate) as in sub base of flooring complete all as specified and directed. |
| 105 | M&L chequered cement concrete tiles with grey and any pigments 30cm x30cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors and incl cement screed 15mm thick in 1:6 complete all as specified and directed. |
| 106 | M&L for 75mm thick in cement concrete type C2 1:3:6 (Using 40mm graded stone aggregate) as in sub base flooring /plinth protection finished even and smooth with out using extra cement complete all as specified and directed. |
| 107 | Removing building material i.e., bitumen felt, concrete, tiles, debris etc ) outside dockyard premises exc 5.00 km complete all as specified and directed, |
| 108 | Material & Labour for providing and fixing stainless steel (Grade 304) of railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specfied and directed. |
| 109 | M&L for brickwork with fly ash bricks in one brick thick honey-comb walling, built in (1:4) cement mortar complete all as specified and directed. |
| 110 | M&L rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 and finished even and smooth without using extra cement complete all as specified and directed. |
| 111 | Demolition of reinforced cement concrete in any position and removal of rubbish outside dockyard premises complete all as specified and directed. |
| 112 | M&L for reinforced cement concrete (M-25 grade using 20mm graded aggregate) Beams, cantilevers, bressummers, lintels over 1.5m span all as specified and directed. |
| 113 | M&L for reinforced cement concrete (M-25 grade using 20mm graded aggregate) Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed. |
| 114 | M&L for precast reinforced cement concrete type C1 (1:3:6) (20mm graded stone aggregate) in manhole covers setting in cement mortar (1:4) complete all as specified and directed. |
| 115 | M&L for cement concrete type B2 1:2:4 (40 mm graded stone aggregate) as in surface channels and drains complete all as specified and directed. |
| 116 | M&L for brickwork with subclass ‘B’ bricks used as brick bats all as specified and as directed. |
| 117 | Dewatering / desludging of septic tanks,soakage wells etc, cleaning of all sludge ,silt residue of both orgenic and inorgnic nature by manual labour or by mechanical scrappers etc and disposal off the same out side the Dockyard area and including dumping the material to any depth, complete all as specified and directed. |
| 118 | Cleaning of manhole by taking out sludge in semi liquid/solid stage (Incl all wate etc) from inside of manhole of depth not exceeding 1.5 m and removing the sludge and disposal off the same out side the Dockyard area and including dumping the material to any depth, complete all as specified and directed. |
| 119 | Excavation in trenches, not exc 1.5m wide and not exc 1.5m deep and getting out in soft and loose soil complete all as specified and directed. |
| 120 | Returning filling in including spreading, leveling watering and well ramming in layers not exc 25 cm complete all as specified and directed. |
| 121 | Removal of extra excavated soil not exc 50m and depositing where directed at level not exc 1.5m above the starting point complete all as specified and directed. |
| 122 | M&L for PCC 1:3:6, type C2 (using 40mm graded stone aggregate), concrete bed to 100 mm dia drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested complete all as specified and directed. |
| 123 | M&L for PCC 1:3:6, type C2 (using 40mm graded stone aggregate), concrete bed to 150 mm dia drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested complete all as specified and directed. |
| 124 | M&L for Salt-Glazed stone ware drain pipes, 100mm dia (internal dia) laid in trenches and jointed as specified complete all as specified and directed. |
| 125 | M&L for salt-Glazed stone ware drain pipes, 150mm dia (internal dia) laid in trenches and jointed as specified complete all as specified and directed. |
| 126 | M&L for cutting of existing 100mm dia manholes for connecting new drains making good to pipe and rendering cutting out existing benching for and forming benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching required complete all as specified and directed. |
| 127 | M&L for cutting of existing 150mm dia manholes for connecting new drains making good to pipe and rendering cutting out existing benching for and forming benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching required complete all as specified and directed. |
| 128 | Extra for forming fair finished drain or channel 60 cm inner girth in cement concrete, using extra cement, including forms, moulds, mi- tred/stopped ends etc., all as specified and directed. |
| 129 | M&L for PCC 1:2:4, type B1, (using 20mm graded stone aggregates) for Coping, lintel bands etc complete all as specified and directed. |
| 130 | M&L for framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks,manhole covers, duct covers and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and directed. |
| 131 | Taking up deposited silt/earth from existing brick drain / open drain/closed drain and culverts to clear the water ways and removing the deposited silt/earth to a distance ecx 100m but not exc 250m complete all as specified and directed |
| 132 | [SCHEDULE 'A' PART-II [E/M WORKS] |
| 133 | Taking down old unsv copper /aluminium point wiring (light, fan.socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc removing materials to store for keepin or for taking credit (credit for above items should be made as per conditions separately ) and making good disturbed surfaces of walls,floors etc., complete all as specified and directed. |
| 134 | Taking down old UNSV DBs and main switches along with MCB's and MCCB's all as specified and directed. |
| 135 | M&L concealed point wiring with with 1.5 sq mm (nominal area), PVC insulated, stranded single core unsheathed FRLS copper conductor cable drawn through with PVC conduit medium grade with all fittings and accessories of PVC conduit/ casing caping (like Tee, bend etc) complete fixed to walls etc with and including 1.5 sqmm (nominal area) PVC insulated stranded single core unsheathed FRLS copper cable as earth continity wire connecting to common earth point including supply & fixing of galvanized pressed mild steel Modular terminal boxes of suitable size as require for fixing modular switch socket regulator etc. complete all as specified and directed including necessary chase cutting for conduits to walls, floors and sinking boxes and making good to walls, floors complete all as specified and directed. |
| 136 | One light point point controlled by one 5 Amps switch one way |
| 137 | One fan point controlled by one 5 Amps switch one way |
| 138 | One 3/5 pin 5 Amp switch socket outlet on independent board |
| 139 | One 3/5 pin 5 Amp socket outlet on same board. |
| 140 | Supply & fix modular type switch 6 Amp oneway flush type all as specified and directed. |
| 141 | Supply & fix modular type switch 6 Amp twoway flush type all as specified and directed. |
| 142 | S&F Modular Switch socket outlet 2 in 1,3 pin 5 amp all as specified and directed. |
| 143 | S&F modular coverplate with support plate for 3 modules and more complete all as specified and as directed. |
| 144 | S&F modular coverplate with support plate for 8 modules and more complete all as specified and as directed. |
| 145 | M&L for concealed point wiring with with 2.5 sq mm (nominal area), PVC insulated, stranded single core unsheathed FRLS copper conductor cable drawn through with PVC conduit medium grade with all fittings and accessories of PVC conduit / casing caping (like Tee, bend etc) complete fixed to walls etc with and including 2.5 sqmm (nominal area) PVC insulated stranded single core unsheathed FRLS copper cable as earth continity wire connecting to common earth point including supply & fixing of galvanized pressed mild steel Modular terminal boxes of suitable size as require for 3/5 pin socket outlet 15 Amps including necessary chase cutting for conduits to walls, floors and sinking boxes and making good to walls, floors complete all as specified and directed. |
| 146 | S&F 6/15 Amps modular switch socket combination complete all as specified and directed. |
| 147 | S&F ceiling rose,3 phase /PVC/ polycarbonate, isolated body all as specified and directed. |
| 148 | S&F fan step regulator, 120W - 2 module complete allas specified and as directed |
| 149 | Supply & fix LED batten with CRCA body, pre coated with white and prewired suitable for LED tube 2x20 watt 4'long alongwith 2 number of tube all as specified and directed. |
| 150 | S&F SP MCB 6 to 32 Amps C Curve complete all as specified and directed |
| 151 | S&F TPN MCB 63 Amps C Curve complete all as specified and directed |
| 152 | S&F TP MCB 63 Amps C Curve complete all as specified and directed. |
| 153 | S&F MCB, Double Pole, 32 amps, 240 Volts, 10 KA breaking cap, ‘’C” curve incl dismantling taking down unsv one all as specified and directed. |
| 154 | S&F MCB distribution board, IP 43 protection, Double door, metal enclosure, SPN, 230 Volts, 8 way including dismantling taking down unsv one all as specified and directed. |
| 155 | S&F doubledoor TPN DB 4 way double door with 200 amp rated bus bar all as specified and directed. Please Enable Macros to View BoQ information |
| 156 | S&F doubledoor TPN DB 4 way double door with 200 amp rated bus bar all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 05, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 02, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 25 daysSep 04, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 27 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender