Tender For Special Repairs Of Jetty X And Y Under Naval Dockyard, Visakhapatnam Under Ge (I) Dm Visakhapatnam
Tender Value
17.02 Crore
Estimated cost
Bid Submission
02 Sep 2026
22 days left
EMD
11.76 Lakhs
Bank guarantee accepted
Document Fee
3000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Visakhapatanam → Andhra Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repairs Of Jetty X And Y Under Naval Dockyard, Visakhapatnam Under Ge (I) Dm Visakhapatnam
BOQ
| Sl. No. | Item Description |
| 1 | [SCHEDULE 'A' PART-I [B/R WORKS] |
| 2 | Demolition of concrete (Un reinforced) of any description and in any position not otherwise specifically provided for and removing debris outside ND(V) complete all as specified and directed. |
| 3 | M&L for design mix cement concrete M-40 grade (Using 20mm graded stone aggregate) as in floor finishing the surface fair & even with out using extra cement complete all as specified and directed. |
| 4 | M&L for forming Construction (Dummy) Joints 30mm deep X 10mm wide filled with sealing compound Grade A complete all as specfied and directed. |
| 5 | Material & labour for chipping (20mm to 50mm thick) of existing damaged, cracked , spalled & loose portion of concrete of the RCC members completely till the reinforcement is exposed and sound concrete is observed by using mechanical means and manual chisels and further the surface is jetted with clean water for removal of dust and loose particles present in the surface and making good the corrogated reinforcement by providing reinforcement/ welded steel wire fabric for strengthing the structure by welding or tying with MS wire (anealled) not less than 0.90mm dia where required and removing of dust and loose particles complete all as specified and directed.Note : Reinforcement / welded steel wire fabric shall be measured and paid as Supply only rate under resceptive items in this schedule. |
| 6 | M&L for preparation of exposed surafaces of rusted steel reinforcement with metal wire brush , cleaning the rusted surfaces free from loose rust and application of rust remover cum passivator painted with brush to the rusted reinforcement , and removing rust with flex after 24 hours of application of rust remover with the help of wire brush, sand paper and thoroughly washed with water with the help of pressure jet and allowing it to dry and providing , mixing and applying zinc anti-rust agent as per manufacturers method of application to rebar corrosion protection system to reinforcement ( Sika / fosroc/BASF/ Dr sunanda or equivalent as specified in PS) @3.75Kg/Sqm surface of steel reinforcement in two coats complete all as specified and directed ( Area of cleaned reinforcement steel bar shall be measured for payment.) |
| 7 | Supply only welded steel wire fabric fixed to RCC wall/ceiling with necessary fixing arrangement weight exc 3 kg/sqm but not exc 4 Kg/Sqm complete all as specified and directed. |
| 8 | Supply only deformed or twisted reinforcement bar of any dia all as specified and directed. |
| 9 | Material & labour applying a coat of Polymer modified cementious bonding coat on the concrete surfaces with one part of Styrene Butadiene Rubber latex emulsion (SBR latex) manufactured by M/s Fosroc chemicals or equivalent chemicals manufactured by Sika India Pvt Ltd / Choksey Chemicals Pvt. Lt M/S Mapei Const Product India PVT Ltd M/S Thermax Ltd/ M/S STP / M/S Dr Sunanada / M/S BASF or equivalent as specified in PS with four parts of water and six parts of cement by weight. Coverage of SBR latex-0.25Ltr / sqm for one coat complete all as specified and directed. |
| 10 | Material & laobur for application of polymer modified reinstatement mortar 20mm thick in isolated places of repair works of RCC members with Rendroc S2 of M/s Fosroc makeor equivalent chemicals manufactured by Sika India Pvt Ltd / Choksey Chemicals Pvt. Lt M/S Mapei Const Product India PVT Ltd M/S Thermax Ltd/ M/S STP / M/S Dr Sunanada / M/S BASF or equivalent as specified in PS having a compressive strength of 40 MPa complete all as specified and directed. |
| 11 | Material & labour for providing Shear connectors and Anchoring by drilling 16 mm dia holes up to depth of 100mm in concrete surfaces and fixing 10 mm dia TMT bars L shaped anchor rods as shear connectors by using Fosroc Lokfix chemical or equivalent as specified in PS (Mix of base and hardener of the polyester resin) in defective concrete area of the slab / column / beams / chajjas / lintel etc or any other structural member as per site requirement after cleaning the drilled hole by using water jet and after drying clean the surface with blower to remove all loose fine particles present in the hole. The Mix of base and hardener of the polyester resin shall be prepared by thorough mixing of base & hardener by the help of spatula. After preparing the mix the holes shall be filled to a minimum depth of 1/3rd of the hole with the prepared polyester resin and the reinforced bar shall be inserted to full depth of hole and extra length of the reinforcement bar shall be bent into the concrete to maintain proper cover to the reinforcement complete all as specified and directed. |
| 12 | Material & labour for 50 mm thick gunniting by chemical mortar prepared by Renderoc DS40 manufactured by Fosroc (25 kg Renderoc DS40 mixed with 12.5 kg of 6 mm downgraded crushed stone aggregate ) or equivalent chemicals manufactured by Sika India Pvt Ltd / Choksey Chemicals Pvt. Lt M/S Mapei Const Product India PVT Ltd M/S Thermax Ltd/ M/S STP / M/S Dr Sunanada / M/S BASF or equivalent as specified in PS on prepared concrete surfaces complete all as per manufacture's instruction & as directed. |
| 13 | Material & labour for 20 mm thick gunniting by chemical mortar prepared by Renderoc DS40 manufactured by Fosroc (25 kg Renderoc DS40 mixed with 12.5 kg of 6 mm downgraded crushed stone aggregate ) or equivalent chemicals manufactured by Sika India Pvt Ltd / Choksey Chemicals Pvt. Lt M/S Mapei Const Product India PVT Ltd M/S Thermax Ltd/ M/S STP / M/S Dr Sunanada / M/S BASFor equivalent as specified in PS on prepared concrete surfaces complete all as per manufacture's instruction & as directed. |
| 14 | Demolition of RCC workof any description and in any positon complete all as specified and directed. |
| 15 | M&L for fixing injection grouting nozzle of suitable size and injecting grouting material, low viscosity epoxy based grouting material Conbextra EP10 or equivalent chemicals manufactured by Sika India Pvt Ltd / Choksey Chemicals Pvt. Lt M/S Mapei Const Product India PVT Ltd M/S Thermax Ltd/ M/S STP / M/S Dr Sunanada / M/S BASF or equivalent as specified in PS in to the cracks with pressure of 40 psi mechanically including sealing the hole complete. Note: The rate quoted by the contractor is including Conbextra EP10 epoxy grouting material. |
| 16 | M&L for laying cement based Micro-concrete, Rendroc RG 40 of Fosroc make, or equivalent chemicals manufactured by Sika India Pvt Ltd / Choksey Chemicals Pvt. Lt M/S Mapei Const Product India PVT Ltd M/S Thermax Ltd/ M/S STP / M/S Dr Sunanada / M/S BASF or equivalent as specified in PS pre packed single component, chloride free, sulphate free, non-shrink, free flow, self compacting , ready to use after mixing water in specified proportion of approved quality. Form work shall be provided for placing micro concrete patch repair as required at site with steel jack system and steel props to support the form work in this application of high strength, dual shrinkage, compensated, micro concrete for placing in nominal thickness of more than 50mm for concrete repair with compresive strength of 40 Mpa complete.Note : The unit rate quoted by the contractor is inclusive of formwork. |
| 17 | Taking down cement plaster on walls/Ceiling etc including racking out joints hacking for key scrubbing down with water and removing the debries away from the Dockyard premises all as specified and directed. |
| 18 | M&L for rendering 15 mm thick plaster in CM (1:4) using SBR latex emulsion @ 4% by weight of cement on fair face of brick or concrete surfaces of walls finished even and smooth without using extra cement, (Make of SBR emulsion/latex: Sika, Fosroc, STP, BASF, star coatings, or equivalent as specified in PS).Note: The unit rate quoted by the contractor is inclusive of SBR Latex. |
| 19 | M&L for preparation of surfaces of vertical concrete surfaces of jetty on sea side wall by mechanical scaryfying for key ( partly under sea water during high tide times), removing all loose particles, laitance, oil, greese, sea weed etc., before application of levelling putty complete all as specified and directed. |
| 20 | M&L for application of single component, polymer modified, cementitious mortar of Rendroc FC (M/s Fosroc or equivalentas specified in PS) filler for minor surface imperfections of average thickness 3mm complete all as specified and directed. |
| 21 | M&L for application of high performance aliphatic acrylate based protective and decorative coating on vertical concrete surfaces of jetty sea face wall with two coats of Deck guard 'S' of Fosroc, 2.85 Sqm per one Ltr (300 microns thick ) over a coat of Deckguard primer @ 2.5 Sqm per one Ltr complete all as specified and directed. |
| 22 | M&L for removing the existing damaged, peeled out floor treatment of any description (20mm average thickness) by mechanical / hand tools to expose the concrete surface and disposal of the rubbish from the Naval dock yard complete all as specified and directed. |
| 23 | M&L for surface preparation of the existing rough surface of concrete (after removal of existing flooring under item No 21 above) by means of mechanical grinding to achieve a rough, coherent substrate having an excellent anchor profile, removing all the loose particles, dirt, etc., clean with high pressure water jet and allow it to dry complete all as specified and directed. |
| 24 | M&L for crack repairs by widening the cracks 0.25mm to 9mm wide, groove cutting to V shape in existing jetty slabs, cleaning out by removing loose particles by mechanical blower and application of Epoxy based primer Nitoprime 25 to the groove and allow it to dry and application of Epoxy putty Nito VF in the prepared groove after complete drying of the applied primer complete all as specified and directed.Make : Nitoprime 25 of Fosroc or equivalent as specified in PS. |
| 25 | M&L for fixing injection grouting nozzle of suitable size and injecting grouting material, low viscosity epoxy based grouting material Conbextra EP10 or equivalent chemicals manufactured by Sika India Pvt Ltd / Choksey Chemicals Pvt. Lt M/S Mapei Const Product India PVT LtdM?S Thermax Ltd/ M/S STP / M/S Dr Sunanada / M/S BASF or equivalent as specified in PS in to the cracks with pressure of 40 psi mechanically including sealing the hole complete all as specified and directed. Note: The rate quoted by the contractor is including Conbextra EP10 epoxy grouting material |
| 26 | M&L for patch repair in concrete surfaces of depth more than 20mm with shrinkage controlled polymer modified fibre reinforced Cementitious patch repair mortar Renderoc SP40 of Fosroc make or equivalent as specified in PS having a compressive strength of 45 Mpa over a coat of Nitobond SBR on the base surfaces includung taking out the old concrete complete Note : 25 Kg of Renderoc SP40 bag ready to use at site by mixing with water at 4.25 Ltr per bag shall be used for patch repairs in concrete. |
| 27 | M&L for application of bonding coat on the prepared old concrete surfaces of the jetty with two component epoxy based bonding agent Nitobond EP of Fosroc make or equivalent as specified in PS for laying 20mm thick Cementitious flooring system complete all as specified and directed. |
| 28 | M&L for 20mm thick cementitious flooring system after application of epoxy based bonding agent on the prepared jetty floor with Nitoflor Levelcrete of Fosroc make or equivalent as specified in PS having a compressive strength of 40Mpa. The pre-pack 20Kg Nitoflor Levelcrete bag shall be mixed with 4Ltr of water as per manufacturers instructions and thoroughly mixed by mechanical means for application on the floor all as specified and directed. |
| 29 | M&L for application of top wearing coat with the properties of Anti-skid, oil resistant, flexible & UV resistant coating system with the following laying methodology :- a) Application of two component Epoxy primer Notoprime 30 of Fosroc make, mixed with mechanical mixer and applied on the level Crete surface by using sponge based epoxy roller followed by sprinkling of anti-slip grain No 2 of Fosroc make on the primed surface on wet condition for skid resistant and allow it to dry for 16-24 hours.b) Application of two component prepacked protective system of Traffic guard Intermediate coat of Fosroc make, mixed with mechanical mixer and applied on the anti-skid surface by using sponge based epoxy roller and allow it to dry for 16-24 hours.c) Application of two component wearing coat, Trafficguard Wearing coarse of Fosroc make , mixed with mechanical mixer and applied on the anti-skid surface by using sponge based epoxy roller and allow it to dry for 16-24 hours.Make : Epoxy primer Notoprime 30 of Fosroc or equivalent as specified in PS. |
| 30 | All as per item No. 1.28 above, but for Saftey line marking, 100 wide, over finished flooring to the required length , colour and shapes for safety markings on jetty. |
| 31 | M&L for preparation of construction joint grooves of size 25 mm X 20 mm, application of primer to the groove, inserting breaker rod in the groove and finally sealing the groove with with Polyuretheane based flooring sealent Colpor 200 of Fosroc make or equivalent as specified in PS and finishing complete all specified and directed. |
| 32 | Dismantling structural steel work of any description complete all as specified and directed. |
| 33 | S & F for rolled mild steel plain or chequred plates confirming to Fe-290, Gde E-165 welded, riveted, bolted attachment to supporting structure of capstan, duct covers, valve pit access platform and working in a confined area including making good the disturbed portion of concrete surfaces with 1:1 1/2 :3 type A0 using 12.5mm stone aggregate complete all as specified and directed. |
| 34 | S & F structural steel framed work such as angle, channel, I beams, etc cut to shape, including bending and welding angles as necessary confirming to Fe-290, Gde E-165 as in supporting structure of valley gutters, duct covers, platforms (0 to -15m level) and capstan, ladders framed balusters, walk ways, railings, cable duct covers, lifting arrengements with pulleys, nosing angle and similar works; including making good the disturbed portion of concrete surfaces with 1:1 1/2 :3 type A0 using 12.5mm stone aggregate complete all as specified and directed. |
| 35 | M & L for preparation of new steel or previously untreated steel and iron surfaces of any description over 10cm width or girth and applying the following paints on the prepared surfaces complete. (a) 1 coat of Primer (Zinc Chrome primer) (1 x 50 micron dry film thickness (dft).(b) 2 coats of A/C (Anti-corrosive paint) (2 x 150 micron dry film thickness (dft).(c) 2 coats of coal tar epoxy paint (2 x 125 micron dry film thickness (dft). |
| 36 | S&F Rubber fender of size 2000mm x 300mm x 200mm depth (or in short lengths to suit the site requirements) and fixed as kerbs on the top of sea face jetty wall with four numbers M24 SS 304 bolts of length 285mm. The fender shall be fixed with a MS galvanized flat of size 100mm X 12mm covering the full length of the fender as directed by Engineer-in-charge. The Properties of the rubber used shall be as follows :- Before aging : Tensile strength not less than 17 MPa, Elongation shall not be less than 350% as per ASTM D412, Hardness Max 70 + 5º, Shore ‘A’ as per ASTM D2240. |
| 37 | After aging at 96 hours at 70º : The tensile strength not less than 80%, Elongation not less than 80% as per ASTM D 412 hardness + 8º shore A as per ASTM 2240, tear strength shall not be less than 70KN/m, Compression set at 70ºC for 22 hours 25% maximum- as per ASTM D 395, abrasion resistance Maximum 1.5CC as per BS 903 A9 and Ozone resistance - no cracks as per ADSTM D 1171. All the above test reports shall be provided by the manufacturer. Necessary factory inspection during manufacturing process shall be arranged by the bidder. The fender is be pre coated with the homogeneous colour with yellow and black alternately complete Note: The item rate shall include the cost of SS M24 bolt, Nuts and chemical for fixing the bolt as recommended and supplied by the manufacturer of rubber fender. |
| 38 | S&F for Rubber arch fender of size 2000mm x 595 / 195mm width at bottom and top respectively x 300 mm depth and fixed vertically on the vertical face of jetty sea face wall with eight numbers M24 SS 304 bolts of length 285mm as directed by Engineer-in-charge. Rubber as per ASTM D-2000-12. The Properties of the rubber used shall be as follows :- Deflection - 51.5%, Reaction force - 25.3 Ton, Energy absorption - 2.95 ton / Mtr with a tolerance of - +10%. Before aging : Tensile strength not less than 17 mpa , Elongation shall not be less than 350% as per ASTM D 412, Hardness Max 70 + 5º, Shore A as per ASTM D2240. |
| 39 | After aging at 96 hours at 70 º : The tensile strength not less than 80%, Elongation not less than 80% as per ASTM D 412 hardness +8º shore A as per ASTM 2240, tear strength shall not be less than 70 KN/m, Compression set at 70ºC for 22 hours 25% maximum- as per ASTM D 395, abrasion resistance Maximum 1.5CC as per BS 903 A9 and Ozone resistance - no cracks as per ADSTM D 1171. All the above test reports shall be provided by the manufacturer. Necessary factory inspection during manufacturing process shall be arranged by the bidder. Note: The item rate shall include the cost of SS M24 bolt, Nuts and chemical for fixing the bolt as recommended and supplied by the manufacturer of rubber fender. |
| 40 | M&L for preparation of new plastered surface and applying two coats of acrylic emulision paint over and including one coat of suiltable primer complete all as specified and directed. |
| 41 | M&L for complete removal of existing treatment of wall/ ceiling surfaces of gallery and applying two coat of acrylic emulision paint over and including one coat of primer complete all as specified and directed. |
| 42 | NOTE: (i) Works shall be excuted in a confined area which reqiures double scaffolding. Contractor should follow OSHA's working norms in this area. The work shall be excuted at any height (up to 20 m height) Contractor necessary safety gears shall be considered> Contractor's quopoted rate is deemed to be inslusive all above mentioned operations /activities . No extra payment is allowed for thease activity. |
| 43 | Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including ainital or similar pattern roof coverings at any height complete all as specified and directed. |
| 44 | S&F Pre- painted galvalume aluminum zinc coating GI based corrugated/semi corrugated/ tripizodial or any pattren profile steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws at any height complete all as specified and directed. |
| 45 | M&L for Partition walls with panels of 1.44 sqm (appx.) made out of aluminum powder coated hollow sections 63.50 x 38.10 x 1.95mm thick ,snap fit beading ,rubber gasket ,5mm thick sheet glass and 12mm thick prelaminated particle board interior grade ,prelaminated one side with decorative chioce lamination and other side balancing light grey lamination including dismantling the damaged partition complete all as specified and directed. |
| 46 | S&F aluminium powder coated door shutter with chowkats made out of hollow aluminium sections as mentioned below, each shutter having 2 Nos ‘D’ type aluminium handles of 200mm long 2 Nos aluminium tower bolts of 200mm long and 1 No mortice lock of 6 lever with key in duplicate, shutter partly glazed with 5.5mm thick sheet glass and partly paneled with 12mm thick particle board pre-laminated fixed with glazing clips, rubber beadings and aluminium beadings complete Chowkat size : 101.60 x 44.45 x 2.40 mm (1.608 Kg/RM appx)Shutter Top rail : 114.30 x 2.15 mm thick (1.836 Kg/RM appx) Bottom rail : 150.00 x 2.20mm thick (2.376 Kg/RM appx) Middle rail : 83.50 x 1.70 mm thick (1.243 Kg/RM appx) Vertical rail : 85.00 x 1.80 mm thick (1.302 Kg/RM appx) |
| 47 | S&F anodised aluminium snap grid frame work of size 605x605mm using main and cross tee of size 15mm x 15mm 1.5mm ( weight not less than 0.12 kg / Rm) and wall angle of size 40mm x 25mm x 2mm ( weight not less than 0.36 kg / Rm) and perforated board for insulation and accoustic purpose 60cm x 60 cm in size and thickness 5 to 8 mm,fixed withn screws to the aluminium frame work in ceiling with screws to aluminum frame work in ceilings with hanger 6mm dia GI (up to 1200mm length) adjusting level fixed to roof slab by means of ceilng cleats made out of GI flat 40x 3mm size 60mm long and expansion hold fastners 12.5mm dia 40mm long and dismantling wall and ceiling boards, (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including wooden cover and fillets and removing away from dockyard premises complete all as specified and directed. |
| 48 | S&F in repairs aluminium composite panel of 3mm thick with skin thickness of 0.25mm of aluminium on both sides, sandwiched by 2.5mm polythene core with PVDF coating of 30 micron, face fully covered with high intensity prismatic (Type-IV) sheeting conforming to type-III of ASTM-D 4956-01 as approved by GE and fixing the same to the structural /wooden/aluminum frame work by means of suitable self tapping screws, rivets or bolts and nuts and erecting in position complete all as specified and directed. |
| 49 | Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) and removing rubbish off the premises complete all as specified and directed. |
| 50 | M&L for coloured non skid ceramic tiles 300 x 300 x 7mm thick in floor set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and incl cement screed 15mm thick in 1:6 complete all as specified and directed. |
| 51 | M&L for glazed ceramic tiles 450mm X 300mm X 7mm) thick as in skirting/dado/vertical surfaces , including 1o mm thick 1:4 CM etc set and jointed in neat cement slurry provided in colured cement to match the coloured tiles complete all as specified and directed. |
| 52 | S & F in repair Vitreous China Ware Wash hand basin white, flat back, size 550 x 400 mm size (flat back or angle back type) in repairs including cutting for and pinning ends of brackets or erecting stand in repairs complete all as specified and directed. |
| 53 | S&F in repairs vitreous china half stall urinal (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe complete all as specified and directed. |
| 54 | S&F in repairs urinal spreader of chromium plated push type with PVC pipe of 15mm bore as required complete all as specified and directed. |
| 55 | S & F in repairs Vitrous China urinal partition white of size 310x700mm complete all as specified and directed. |
| 56 | S&F in repairs 5mm thick bevelled edge looking mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers all as specified and directed. |
| 57 | Taking down GI tubing 15mm dia with all connection all as specified and directed. |
| 58 | All as per item No. 20, but 20mm dia |
| 59 | S & F 15 mm bore Galvanized Steel tubes, medium grade for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors all as specified and directed. |
| 60 | S & F 20 mm bore Galvanized Steel tubes, medium grade for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors all as specified and directed. |
| 61 | S & F in repairs Fancy type chromium plated 15 mm bore Stop valves, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions all as specified and directed. |
| 62 | S & F in repairs 15 mm bore pillar taps, Cast Copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe all as specified and directed. |
| 63 | S&F in repair 15 mm Bib tap standard of PTMT any colour high pressure screwed for iron pipe and fixed. (Minimum weight 15mm-90gms 20mm-125gms) all as specified and directed. |
| 64 | S & F 20 mm dia Gun Metal, globe or Gate Valve with Iron wheel head Screwed both ends for Iron Pipe and fixed in repairs all as specified and directed. |
| 65 | S & F in repair 110 mm bore PVC (SWR) , waste and rain water pipes single socketed in any length with rubber ring joints complete all as specified and directed. |
| 66 | S & F in repair 110 mm bore PVC (SWR) bends of any radius all as specified and directed. |
| 67 | M & L 110mm bore PVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified and directed. |
| 68 | S&F in repairs grating round of size 100mm dia, chromium plate complete all as specified and directed. |
| 69 | Disconnecting existing U/S water tank 1000 ltrs and fixing rotational moulded polyethylene new water storage 1000 ltrs cap tanks (cylindrical vertical with closed top)hoisted and fixed in position complete all as specified and directed. |
| 70 | Taking down Chowkats or frames not exceeding 1.5 Sq. M each but (Without taking off shutters from the frame) and removing away from site all as specified and directed. |
| 71 | S & F solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, supporting and fixing in opening as per specification and drawing complete all as specified and directed. |
| 72 | S & F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out MS tubes for top and bottom rails MS shall be cuvred with heat moulded plain colour PVC `C` channel having PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side as gap insert for top rail and bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame / sealed to the styles and rails with suitable PVC sheet beading and jointed together with solvent cement supplying and fixing in the frame at site as per specification |
| 73 | S&F 100mm Stainless steel butt hinges fixed with SS screws complete all as specified and directed. |
| 74 | S&F 150mm aluminium anodized barrel tower bolt of extruded section all complete all as specified and directed. |
| 75 | S&F 150mm aluminium anodized handles, cast type complete all as specified and directed. |
| 76 | S&F in repair precast cement concrete louvres and jallies, 25mm thick (measured solid) type B0 (1:2:4 using 12.5mm stone aggregate) set in cement mortar 1:4 , including all mould- ings but excluding frame complete all as specified and directed.(Pre cast frame shall be measured separately). |
| 77 | [SCHEDULE 'A' PART-II [E/M WORKS] |
| 78 | Dismantling taking out LT/HT cable from cable rack/floor of sub station for repair/re[placement of wornout steel cable rack or for realingnmetn of cable and refixing the cables with proper staking with proper alingnment of cable and refixing the cables with proper on repaired/existing rack and making feeder wise bundle of cable using PVC cable tie for sizes of cable 2.0/3.0/3.5 core 95 sqmm to 185 sqmm 11000/1100 volt grade all as specified and directed,Note : (i) Each cable shall be measured separately. Steel cable rack shall be measured separately as supply and fix. (ii) All cable removed from cable gallery to MES Store and after competion of B/R work all cable relaying its original position. |
| 79 | All as per item No. 1.00 above, but for cable size 240 sqmm |
| 80 | All as per item No. 1.00 above, but for cable sizes 300 sqmm |
| 81 | All as per item No. 1.00 above, but for cable sizes 400 sqmm |
| 82 | Dismantling dead/defective/unused cable of any size from gallery to remove outside gallery complete all as specified and directed. |
| 83 | Material and labour for new XLPE LT 1.1 KV straight through jointing kit heat shrinkable type for XLPE LT 1.1 KV under ground cable 3.5 core armoured aluminium conductor cable after crimping ferrules, taping incuding termination, testing and commissioning the cable for the following sizes all as specified and directed. |
| 84 | 150 Sqmm to 185 Sqmm 3.5 core |
| 85 | 240 to 400 sqmm 3.5 core |
| 86 | Supply only Heat shrink cable end terminal for 3.5 core 1100 V, 150 to 185 sqmm all as specified and directed.Make : Cat No MHI/Ox1.1KV (HESL-4/4C) of 3M or equivelent of Denson/M Seal/MS Seal/RPG |
| 87 | Supply only Heat shrink cable end terminal for 3.5 core 1100 V, 240 to 300 sqmm all as specified and directed.Make :- Cat No MHI/Ox1.1KV (HESL-5/4C) of 3M or equivelent of Denson/M Seal/MS Seal/RPG |
| 88 | Supply only Heat shrink cable end terminal for 3.5 core 1100 V, 400 to 500 sqmm all as specified and directed.Make :- Cat No MHI/Ox1.1KV (HESL-6/4C) of 3M or equivelent of Denson/M Seal/MS Seal/RPG |
| 89 | Supply and fix MS cable support structure made with ISA 75x75x8mm grouted to gallary wall with stainless steel fastner bolt of dia not less than 16 mm at interval of 300 mm fixing of cross support with SS nuts and bolts not less than 16 mm dia, painting the MS structure with one coat of red oxide primer and two coat of synthetic enamel paint complete including taking out old UNSV cable support structure from the jetty gallary complete all as specified and as directed. |
| 90 | S&F Galvanised iron earthing strip 32 x 6mm including connection making necessary drilled hole incl dismantling taking out unserviceable earthing strip of any size to PB/CP/JB/main earth bus all as specified and directed. |
| 91 | Removing Pillar box cum cope points after disconnection of all cable from its original position to MES store and after competion of B/R work fixing its original position with all cable connection, PCC foundation and all necessray work complete all as specified and directed. |
| 92 | M & L for XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 400 sq. mm 3½ core complete all as specified and directed. |
| 93 | M & L for XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 240 sq. mm 3½ core complete all as specified and directed. |
| 94 | M & L for XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 300 sq. mm 3½ core complete all as specified and directed. |
| 95 | Materials & labours for surface wiring with 2 x 2.5 sqmm (Nominal area) single core PVC insulated unsheathed 1100 volt grade multi stranded FRLSH Copper conductor cable drawn through in and including FRLS PVC Conduit medium grade with all fittings and accessories alongwith one single core green colour PVC insulated unsheathed 1100 volt grade multi stranded FRLSH Copper conductor cable of size 2.5 sqmm as earth lead and connected to earth dolly including dismantling taking down old unserviceable wiring and making good to disturbed surfaces all as specified and directed. |
| 96 | Material & Labour for surface wiring with 2 x 4.0 sqmm (Nominal area) single core PVC insulated unsheathed 1100 volt grade multi stranded FRLSH Copper conductor cable drawn through in and including FRLS PVC Conduit medium grade with all fittings and accessories alongwith one single core green colour PVC insulated unsheathed 1100 volt grade multi stranded FRLSH Copper conductor cable of size 4.0 sqmm as earth lead and connected to earth dolly including dismantling taking down old unserviceable wiring and making good to disturbed surfaces all as specified and directed. |
| 97 | Supply and fix 20 mm dia medium grade PVC rigid conduit with all fittings and accessories of PVC conduit (like Tee, bend etc.) including taking down old one complete all as specified and directed. |
| 98 | Supply & fix ceiling rose surface Bakelite three terminal including dismantling taking down unserviceable one all as specified and as directed. |
| 99 | Supply and fix LED batten with high lumen output, environmental friendly, energy efficient ready to use pack, 20 W LED, 6500 K, 230V, 4' long including taking down old unserviceable complete all as specified and directed. |
| 100 | Supply and fix steel protection grill of light fittings inside gallery ceiling made with 1' square grill of 3mm thick wire, bent to half round shape of 150mm dia, 1400mm long, all edge supported by welding to grill with 15x3mm MS flat and fixing arrangement to ceiling of gallery complete all as specified and directed. |
| 101 | Supply and fix energy saving, environment friendly & robust mediumbay/Highbay LED 150W Luminaire with high effieancy (100 lm/W) with toughened glass including taking down old unserviceable complete all as specified and directed. |
| 102 | S&F Vertical MCB distribution board, including 4 pole MCCB, 16 KA, 100 amps, incomer, IP 43 protection, Double door, metal enclosure, TPN, 415 Volts, 4 way including dismantling taking down unserviceable one all as specified and directed. |
| 103 | Supply and fix to wall/ ceiling of jetty gallery with proper clamp or drawn through cable rack PVC/XLPE inslulated armoured heavy duty electric cable with stranded copper conductor, 1100 V grade cross section area 06 Sqmm, 2 Core including connection at both end to specified location including taking out old one complete all as specified and as directed. |
| 104 | All as per item No 26 above, but of size 16 Sqmm 4 core |
| 105 | M & L for MS ladder type cable tray 600 mm width 2.5 mm thickness and 50mm height with connected item including coupler plate, nut, bolt etc for laying of cable with one coat of red oxide and two coats synthetic enamel paint taking down old unserviceable one complete all as specified and directed. |
| 106 | Supply and fix MCCB, 200 Amps 4 pole with breaking capacity 35 KA adjustable type including enclosure box taking down old unserviceable one complete all as specified and directed. |
| 107 | Supply and fix MCCB, 400Amps 4 pole with breaking capacity 35 KA adjustable type including enclosure box taking down old unserviceable one complete all as specified and directed. |
| 108 | Supply and fix MS ERW pipe of size 200 mm dia heavy duty including all accessories including taking down old UNSV complete all as specified and directed. |
| 109 | Supply and fix MS ERW pipe of size 100 mm dia heavy duty including all accessories including taking down old UNSV complete all as specified and directed. |
| 110 | Supply and fix MS ERW pipe of size 80 mm dia heavy duty including all accessories including taking down old UNSV complete all as specified and directed. |
| 111 | Supply and fix installed testing and commisiong both end flange 200 mm dia bore CI sluice valve class PN 1.6 conforming to IS 14846 (2000) with iron wheel handle and ss spindle including necessary nuts bolts washers rubber gasket taking down old unserviceable one complete all as specified and directed |
| 112 | Supply and fix installed testing and commisiong both end flange 100 mm dia bore CI sluice valve class PN 1.6 conforming to IS 14846 (2000) with iron wheel handle and ss spindle including necessary nuts bolts washers rubber gasket taking down old unserviceable one complete all as specified and directed |
| 113 | Supply and fix installed testing and commisiong both end flange 80 mm dia bore CI sluice valve class PN 1.6 conforming to IS 14846 (2000) with iron wheel handle and ss spindle including necessary nuts bolts washers rubber gasket taking down old unserviceable one complete all as specified and directed |
| 114 | Supply and fix installed testing and commisiong fire hydrant valve with CI body brass parts single headed 63 mm dia with iron wheel handle and ss spindle including necessary nuts bolts washers rubber gasket complete taking down old unserviceable one all as specified and directed |
| 115 | Supply and fix installed testing and commisiong fire hydrant valve with CI body brass parts double headed 63 mm dia with iron wheel handle and ss spindle including necessary nuts bolts washers rubber gasket taking down old unserviceable one complete all as specified and directed |
| 116 | Supply and fix internal hose box made of 2 mm thick MS sheet 800mm x 600mm x 250mm with double door with 4 mm thick glasses and door frame of 2mm thick MS sheet painted fire red outside and brillent white inside surface incl dismantling/ taking out unserviceable one complete all as specified and directed |
| 117 | Supply and fix installed testing and commisiong 50mm CI air reales valve including necessary bolt and nuts taking down old unserviceable one complete all as specified and directed |
| 118 | Supply and fix GI pipe medium grade 80 mm bore galvanised with all fittings such as tees , bends, elbows, socketsreducers, nipples and union dismantling/taking out unserviceable one complete all as specified and directed |
| 119 | Supply and fix GI pipe medium grade 150 mm bore galvanised with all fittings such as tees , bends, elbows, sockets reducers, nipples and union dismantling/taking out unserviceable one complete all as specified and directed |
| 120 | M & L Non Return butterfly Valve of 150mm dia with all assesserise including taking out oid unserviceable complete all as specified and directed. |
| 121 | M & L Non Return butterfly Valve of 80mm dia with all assesserise including taking out oid unserviceable complete all as specified and directed. |
| 122 | M & L up to 150 mm Bends (any type, radius and angle) tapers any type, (straight, bend, increasing ,(straight, bend, increasing,decreasing or double socket etc.) Tee pieces single branch. \\"Y\\"junction, double branch, cross (all sockets or socket and spigot) collars, caps and plugs all as specified and directed. |
| 123 | Supply and lay 150 mm dia M S Pipes heavy grade with all fittings laid in floors or fixed to walls and ceilings complete all as specified and as directed. |
| 124 | M & L for Servicing of existing LT Panel and switch gear having capacity upto 2000A, including painting, Cable end Termination, replacing of lugs and bolt nuts etc.complete all as specified and as directed. |
| 125 | M & L for removing the complete existing busduct as per site/phase wise with special attention of system care to keep without any damages and refixing the same as per site requirement phase wise along with provision flanges to keeping alive of certain portion for feeding supply to particular PBs and CPs all as directed including testing and commissioning all as specified and directed. |
| 126 | Supply and fix exhaust fan, steel body AC single Phase. 230V of size 450m sweep with, blades, and frame and louvers including taking down old unserviceable complete all as specified and directed. Please Enable Macros to View BoQ information |
| 127 | Supply and fix exhaust fan, steel body AC single Phase. 230V of size 450m sweep with, blades, and frame and louvers including taking down old unserviceable complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 05, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 02, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 22 daysSep 04, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 24 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender