Tender For Construction Of 02 Nos Connecting Road Between 75.00Mtr Wide Road To 30.00 Mtr .Airport Peripheral Road In Sector -32, Yeida.Wc-03
Tender Value
1.54 Crore
Estimated cost
Bid Submission
14 Aug 2026
2 days left
EMD
3.08 Lakhs
Bank guarantee accepted
Document Fee
2725
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Gautam Buddha Nagar → Uttar Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of 02 Nos Connecting Road Between 75.00Mtr Wide Road To 30.00 Mtr .Airport Peripheral Road In Sector -32, Yeida.Wc-03
BOQ
| Sl. No. | Item Description |
| 1 | Clearing grass and removal of the rubbish up to a distance of 50 m Outside the periphery of the area cleared. (Based UP PWD SOR 2020) |
| 2 | Construction of embankment with material approved material obtained from pits with all lift and leads,transporting to site spreading ,grading to required slope and compacting to meet required of table 300-2 upto 10 km Morth-305. Lead up to 10 Km. |
| 3 | Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres. SOR 20/16.1/p-263 |
| 4 | Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. With material conforming to Grade-II (size range 53 mm to 0.075 mm ) having CBR Value-25, MORTH-401 |
| 5 | Add Royalty Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. With material conforming to Grade-II (size range 53 mm to 0.075 mm ) having CBR Value-25, MORTH-401 |
| 6 | Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix macadam (WMM) specification including premixing the material with water at OMC in mechanical mix plant, carriage of mixed material by tipper to site, for all leads & lifts, laying in uniform layers with mechanical paver finisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. MORTH-406 |
| 7 | Add Royalty Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix macadam (WMM) specification including premixing the material with water at OMC in mechanical mix plant, carriage of mixed material by tipper to site, for all leads & lifts, laying in uniform layers with mechanical paver finisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. MORTH-406 |
| 8 | Brick edging in full brick width and half brick depth including excavation, refilling and disposal of surplus earth lead upto 50 metres: With FPS bricks of class designation 150, DAR-2020 /16.7.1 |
| 9 | Cement concrete with 4cm gauge approved stone ballast ,coarse sand & cement in the proportion of 8:4:1 including supply of all material ,labour,tools & plants etc required for proper completion of the work. UPPWD SOR /281/P-17 |
| 10 | Brick work with FPS bricks of class designation 150 in foundation and plinth in: Cement mortar 1:4 (1 cement, : 4 coarse sand) UPPWD/SOR-2020/305(a) |
| 11 | 12mm cement plaster of mix:, 1:6 (1 cement : 6 coarse sand), DAR-20/ 13.4.2Based on UPPWD/SOR-2020 |
| 12 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement in position to the required line, level and curvature jointed with cement mortar 1:3 (1 cement: 3 coarse sand) including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm) including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge). DAR-2020 / 16.69 |
| 13 | Providing and applying primer coat with bitumen 80/100 on prepared surface of granular Base including clearing of road surface and spraying primer at the rate of 0.70 kg/sqm using mechanical means. (VG-10) UPPWD SOR 2020/AR/YEIDA |
| 14 | Providing and applying Tack Coat on Prepared Surface with Bitumen VG-10 using bitumen pressure distributor and spraying on bitumen boiler including Cleaning, preparing the existing road surface as per most specification and as per direction of engineer incharge with 2.50 kg of bitumen for 10 sqm. UPPWD SOR 2020/AR/YEIDA |
| 15 | Close Graded Premix Surfacing/Mixed Seal Surfacing Providing, laying and rolling of close-graded premix surfacing material of 20 mm thickness composed of 11.2 mm to 0.09 mm (Type-a) or 13.2 mm to 0.09 mm (Type-b) aggregates using penetration grade bitumen to the required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a Smooth wheeled roller 8-10 tonne capacity, and finishing to required level and grade. Mechanical means using HMP of appropriate capacity not less than 75 tonnes/hour. |
| 16 | White washing with lime to give an even shade: New work (three or more coats) DAR-2020 /13.37.1 |
| 17 | Add Maintenance @ 2.50 %. |
| 18 | Culvert Excavation of earth in ordinary soil for laying of sewers including cutting of joints, pits, trimming, dressing, levelling, including removal of surplus earth and other dismantalled materials upto distance of 50m. from centre of trenches. 0.00 - 1.50 Mtr |
| 19 | Cement concrete with 4cm gauge approved stone ballast ,coarse sand & cement in the proportion of 8:4:1 including supply of all material ,labour,tools & plants etc required for proper completion of the work UPPWD SOR /281/P-17 |
| 20 | Centering and shuttering including strutting, propping etc. and removal of form for: Foundations, footings, bases of columns, etc. for mass concrete. |
| 21 | Centering and shuttering including strutting, propping etc. and removal of form for: Wall (any thickness) including attached pilasters, butteresses, plinth and string courses etc. |
| 22 | Centering and shuttering including strutting, propping etc. and removal of form for: Suspended Floors, roofs, balconies and access platform. |
| 23 | Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering,shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.(Note :- Cement content considered in this item is @ 330 kg/cum.Excess/less cement used as per design mix is payable/recoverable, All work up to Plinth level. UPPWD SOR/5.33.1 |
| 24 | Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. Thermo-Mechanically Treated bars. UPPWD SOR/5.22.6 Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 05, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 14, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 2 daysAug 17, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 5 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender