Tender For Proposal For Maintenance Work Of Pumping Machinery (Monoblock & Hsc To Maintain Water Supply Under Various Rwss Sub Division Tibbi
Tender Value
7.50 Lakhs
Estimated cost
Bid Submission
13 Aug 2026
1 days left
EMD
15000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Hanumangarh → Rajasthan
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Proposal For Maintenance Work Of Pumping Machinery (Monoblock & Hsc To Maintain Water Supply Under Various Rwss Sub Division Tibbi
BOQ
| Sl. No. | Item Description |
| 1 | Proposal for maintenance work of pumping machinery (monoblock & HSC to maintain water supply under various RWSS Sub division Tibbi |
| 2 | Rewinding of three phase squirrel cage induction motor of Monoblock pump sets including all necessary material and of the same characteristics as original with required size of super enameled copper wire (including cost of copper wire),'E' class insulation material and testing of motor on no load but to be guaranteed against testing on load at site, including transportation of motor pump to and from Div/AEn/JEn store complete as per direction of engineer in charge. |
| 3 | Upto 5 H.P. |
| 4 | Above 5.00 HP & upto 7.5 HP |
| 5 | Above 7.5 HP & upto 10.00 HP |
| 6 | Above 10.00 HP & upto 12.5 HP |
| 7 | Above 12.5 HP & upto 15.00 HP |
| 8 | Above 17.50 HP & upto 20.00 HP |
| 9 | Above 20.00 HP & upto 25.00 HP |
| 10 | SUPPLY & FIXING OF SPARE PARTS FOR MONOBLOCK PUMPSET (MOTOR + PUMP) |
| 11 | Connection Plates |
| 12 | up to 10 HP |
| 13 | 10 HP to 20 HP |
| 14 | Cooling Fan |
| 15 | up to 10 HP |
| 16 | 10 HP to 20 HP |
| 17 | GM/SS bush |
| 18 | Upto 10 HP |
| 19 | 10 HP to 20 HP |
| 20 | Mechanical reconditioning of Bearing sheet |
| 21 | Upto 10 HP |
| 22 | 10 HP to 20 HP |
| 23 | Mechanical reconditioning of Impeller sheet and Key way slot |
| 24 | Upto 10 HP |
| 25 | 10 HP to 20 HP |
| 26 | Oil seal |
| 27 | Upto 10 HP |
| 28 | 10 HP to 20 HP |
| 29 | Labour charge for opening and fitting of pump sets |
| 30 | Upto 10 HP |
| 31 | 10 HP to 20 HP |
| 32 | Rewinding of three phase squirrel cage induction motor of HSC pump sets including all necessary material and of the same characteristics as original with required size of super enamelled copper wire (including cost of copper wire) 'E' class insulation material and testing of motor on no load but to be guaranteed against testing on load at site, including making electric connection at site of installation of motor with starter, alignment with pump sets and transportation to and fro from installation site complete as per direction of engineer in charge at site. |
| 33 | Above 17.50 HP & upto 20.00 HP |
| 34 | Above 20.00 HP & upto 25.00 HP |
| 35 | Above 25.00 HP & upto 30.00 HP |
| 36 | Above 35.00 HP & upto 40.00 HP |
| 37 | SUPPLY & FIXING OF SPARE PARTS HSC PUMP SETS (MOTOR + PUMP) |
| 38 | Connection Plates |
| 39 | 5 HP to 20 HP |
| 40 | 20 HP to 30 HP |
| 41 | 30 HP to 50 HP |
| 42 | Cooling Fan |
| 43 | 5 HP to 20 HP |
| 44 | 20 HP to 30 HP |
| 45 | Fan Cover |
| 46 | 5 HP to 20 HP |
| 47 | 20 HP to 30 HP |
| 48 | G.M./SS Gland Guide Bush |
| 49 | 5 HP to 20 HP |
| 50 | 20 HP to 30 HP |
| 51 | Shaft with Sleeve Chuck Nut |
| 52 | 5 HP to 20 HP |
| 53 | 20 HP to 30 HP |
| 54 | 30 HP to 50 HP |
| 55 | Shaft Chuck Nut |
| 56 | 5 HP to 20 HP |
| 57 | 20 HP to 30 HP |
| 58 | 30 HP to 50 HP |
| 59 | G.M. Neck Ring |
| 60 | 5 HP to 20 HP |
| 61 | 20 HP to 30 HP |
| 62 | 30 HP to 50 HP |
| 63 | Bush Shaft Sleeve of G.M. |
| 64 | 5 HP to 20 HP |
| 65 | 20 HP to 30 HP |
| 66 | 30 HP to 50 HP |
| 67 | G.M. Gland Cover |
| 68 | 5 HP to 20 HP |
| 69 | 30 HP to 50 HP |
| 70 | S.S. Shaft (Non Magnetic) |
| 71 | 5 HP to 20 HP |
| 72 | G.M. Shaft Sleeve Check Nut |
| 73 | 5 HP to 20 HP |
| 74 | 30 HP to 50 HP |
| 75 | M.S. Shaft Check Nut |
| 76 | 5 HP to 20 HP |
| 77 | 30 HP to 50 HP |
| 78 | Cooling pipe set with nozzle & Nut |
| 79 | 5 HP to 20 HP |
| 80 | 30 HP to 50 HP |
| 81 | AIR Cock |
| 82 | 5 HP to 20 HP |
| 83 | 30 HP to 50 HP |
| 84 | JOB WORK FOR REPAIR OF PUMP MOTOR |
| 85 | Bearing Housing (rebuilding, turning & finishing) |
| 86 | 5 HP to 20 HP |
| 87 | 30 HP to 50 HP |
| 88 | Bearing Cap (rebuilding, turning & finishing) |
| 89 | 5 HP to 20 HP |
| 90 | 30 HP to 50 HP |
| 91 | Labour Charges for Dismantling & Assembling of Pump |
| 92 | 5 HP to 20 HP |
| 93 | 20 HP to 30 HP |
| 94 | 30 HP to 50 HP |
| 95 | Coupling with stud and rubber bush |
| 96 | 5 HP to 20 HP |
| 97 | 30 HP to 50 HP |
| 98 | Supply & Fixing of tyre coupling sets according to relevant IS code in Centrifugal couple pump sets of approved make Unit. This job also included re-alignment of centrifugal couple pump set after fixing of tyre coupling set as per directed by Engineer-in charge. |
| 99 | Type 14 Nos. set |
| 100 | Routine maintenance of centrifugal coupled pump and motor including opening, cleaning, greasing and refitting / changing of ball bearing if required, gland refilling and replacing all rusted studs, replacing rubber bushes & coupling nut & bolts for coupling pulley, tightening all nut & bolts of foundation, baseplate, pump & motor etc. Checking & correcting alignment of pump & motor including necessary materials i.e. grease, nut & bolts, studs, washers, gland packing and rubber bushes etc. work done at site complete job |
| 101 | 5 HP to 20 HP |
| 102 | Above 30 HP and up to 50 HP |
| 103 | Replacing of damaged/broken gland packing plate with new gland packing plate suitable for centrifugal pump shafts and nut&bolts etc. complete job. |
| 104 | 5 HP to 20 HP |
| 105 | Above 30 HP and up to 50 HP |
| 106 | Fabrication work |
| 107 | Turning of various sizes of CID Joints Class- 10/ 15 Complete set (Labour Charges), The Joints will be supplied by the Junior Engineer concern of Department and carting to workshop and after turning of these joints, firm is liable to transport upto Junior Engineer concern's store own his cost. |
| 108 | 80 mm dia |
| 109 | 100 mm dia |
| 110 | 125 mm dia |
| 111 | 150 mm dia |
| 112 | 200 mm dia |
| 113 | 250 mm dia |
| 114 | 300 mm dia |
| 115 | Threading on GI Pipes different diameter as below (Rate Per Mouth Threading). The Pipes will be supplied by the Department and carting to workshop and after threading of these pipes, firm is liable to transport upto Junior Engineer concern's store own his cost. |
| 116 | 80 mm |
| 117 | 100 mm |
| 118 | 125mm |
| 119 | 150mm |
| 120 | Cutting of GI/MS/CI Pipes of any class as below (Rate per Mouth- One cutting only making two pieces). The Pipes will be supplied by the Department. |
| 121 | 80 mm |
| 122 | 100 mm |
| 123 | 125mm |
| 124 | 150mm |
| 125 | Welding on M.S. / G.I./CI Pipes and other material by Electric Welding, this includes all the material like welding rods/ equipment like welding machine/ generater, if required for job. |
| 126 | At Workshop |
| 127 | On Site |
| 128 | Providing, Fabrication of Mild Steel Plane Ended/ Flanged Specials like Tees, Bends, Reducers, Enlargers, Plugs, Tail Pieces and Blank Flange made from MS pipes, MS sheet strip and MS Sheet of required sizes by welding, cutting and treading as per site conditions and as directed by the Engineer- In- Charge complete in all respect. |
| 129 | Making of GI Assembly pipe for various sizes including threading, tightening, welding of flange and welding with MS Patti, holes and cable grove making as per required length of 3.00 M/ 6.00 M (Pipse and flangse shall be provided and carting these to workshop by the the department). Length of MS strip will be 100 mm, Width- 20 mm and thickness- 6 mm and to be welded around the strip with pipe and flange. Holes in the flanged will be standard size and above 12 mm dia. in size. After tightening the pipe and flanged, welding will be done at junction of flange and pipe complete in all respect. After preparing of Assembly Pipes, the firm is liable to transport these to concern's divisional store own his cost. |
| 130 | 80 mm |
| 131 | 100 mm |
| 132 | Supplying and fixing of MS Rods for different sizes of sluice valve and should be supplied as according to size of old rods including material and finishing for the following sizes. |
| 133 | Sluice Valve Size 80mm |
| 134 | Sluice Valve Size 100mm |
| 135 | Sluice Valve Size 125mm |
| 136 | Sluice Valve Size 150mm |
| 137 | Sluice Valve Size 200mm |
| 138 | Supplying of Chuck Nut for different sizes of sluice valve and should be supplied as according to size of Check Nut including material for the following sizes. |
| 139 | Sluice Valve Size 80mm |
| 140 | Sluice Valve Size 100mm |
| 141 | Sluice Valve Size 125mm |
| 142 | Sluice Valve Size 150mm |
| 143 | Sluice Valve Size 200mm |
| 144 | Providing of U Plate (U Stand) for different sizes of sluice valve and should be supplied as according to size of old U Plate including material for the following sizes. |
| 145 | Sluice Valve Size 80mm |
| 146 | Sluice Valve Size 100mm |
| 147 | Sluice Valve Size 125mm |
| 148 | Sluice Valve Size 150mm |
| 149 | Sluice Valve Size 200mm |
| 150 | Supplying of MS Rods and Chuck Nut (Complete Set) for different sizes of sluice valve and should be supplied as according to size of Check Nut including material for the following sizes. |
| 151 | Sluice Valve Size 80mm |
| 152 | Sluice Valve Size 100mm |
| 153 | Sluice Valve Size 125mm |
| 154 | Sluice Valve Size 150mm |
| 155 | Sluice Valve Size 200mm |
| 156 | Making Direct Pump Piece with heavy duty pipes (Class- B) and flange (as per table- D) including cutting of pipe, threading welding and MS strip for length - 100 mm, Width- 20 mm and thickness- 6 mm and to be welded around the strip with pipe and flanged. Hole in the flanged will be standard size and above 15 mm in size. After tightening the pipe and flanged, welding will be done at junctin of flange and pipe complete in all respect including cost of material. The Length of Direct Pump Piece will be 30 cm (300 mm). |
| 157 | 3\\" dia size (80 mm) |
| 158 | 4\\" dia size (100 mm) |
| 159 | Making Reducer Pump Piece with heavy duty pipes (Class- B) and flange (as per table- D) including cutting of pipe, threading welding and MS strip for length - 100 mm, Width- 20 mm and thickness- 6 mm and to be welded around the strip with pipe and flanged. Hole in the flange will be standard size and above 15 mm dia. in size. After tightening the pipe and flanged, welding will be done at junctin of flange and pipe complete in all respect including cost of material (Both the larger and smaller pipe will have equal length making reducer). The Total Length of Reducer Pump Piece will be 30 cm (300 mm). |
| 160 | 2”x 3” dia size (50 x 80 mm) |
| 161 | 3”x 4” dia size (80 x 100 mm) Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 05, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 13, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 1 dayAug 14, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 2 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender