Tender For Repairing And Rewinding Of Monoblock Pumps For Urban Water Supply Scheme Under Sub Division Hanumangarh Jn.
Tender Value
15.63 Lakhs
Estimated cost
Bid Submission
20 Aug 2026
5 days left
EMD
31260
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Hanumangarh → Rajasthan
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repairing And Rewinding Of Monoblock Pumps For Urban Water Supply Scheme Under Sub Division Hanumangarh Jn.
Corrigendum
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 12-Aug-2026 | Order No. 2414-25 Date 12.08.2026 | Date | 20-Aug-2026 |
BOQ
| Sl. No. | Item Description |
| 1 | Repairing and Rewinding of Monoblock pumps for Urban water supply scheme under sub division Hanumangarh jn. |
| 2 | Rewinding of three phase squirrel cage induction motor of Monoblock pump sets including all necessary material and of the same characteristics as original with required size of super enameled copper wire (including cost of copper wire),'E' class insulation material and testing of motor on no load but to be guaranteed against testing on load at site, including transportation of motor pump to and from Div/AEn/JEn store complete as per direction of engineer in charge. |
| 3 | Upto 5 H.P. |
| 4 | Above 7.5 HP & upto 10.00 HP |
| 5 | SUPPLY & FIXING OF SPARE PARTS FOR MONOBLOCK PUMPSET (MOTOR + PUMP) |
| 6 | Connection Plates |
| 7 | up to 10 HP |
| 8 | Cooling Fan |
| 9 | up to 10 HP |
| 10 | GM/SS bush |
| 11 | Upto 10 HP |
| 12 | Mechanical reconditioning of Bearing sheet |
| 13 | Upto 10 HP |
| 14 | Mechanical reconditioning of Impeller sheet and Key way slot |
| 15 | Upto 10 HP |
| 16 | Oil seal |
| 17 | Upto 10 HP |
| 18 | Labour charge for opening and fitting of pump sets |
| 19 | Upto 10 HP |
| 20 | Rewinding of three phase squirrel cage induction motor of HSC pump sets including all necessary material and of the same characteristics as original with required size of super enamelled copper wire (including cost of copper wire) 'E' class insulation material and testing of motor on no load but to be guaranteed against testing on load at site, including making electric connection at site of installation of motor with starter, alignment with pump sets and transportation to and fro from installation site complete as per direction of engineer in charge at site. |
| 21 | Above 17.50 HP & upto 20.00 HP |
| 22 | Above 20.00 HP & upto 25.00 HP |
| 23 | Above 25.00 HP & upto 30.00 HP |
| 24 | Above 35.00 HP & upto 40.00 HP |
| 25 | Above 45.00 HP & upto 50.00 HP |
| 26 | Above 75.00 HP & upto 100.00 HP |
| 27 | SUPPLY & FIXING OF SPARE PARTS HSC PUMP SETS (MOTOR + PUMP) |
| 28 | Connection Plates |
| 29 | 5 HP to 20 HP |
| 30 | 20 HP to 30 HP |
| 31 | 30 HP to 50 HP |
| 32 | Above 50 HP to 100 HP |
| 33 | Cooling Fan |
| 34 | 5 HP to 20 HP |
| 35 | 20 HP to 30 HP |
| 36 | 30 HP to 50 HP |
| 37 | Above 50 HP to 100 HP |
| 38 | Fan Cover |
| 39 | 5 HP to 20 HP |
| 40 | 20 HP to 30 HP |
| 41 | 30 HP to 50 HP |
| 42 | Above 50 HP to 100 HP |
| 43 | G.M./SS Gland Guide Bush |
| 44 | 5 HP to 20 HP |
| 45 | 20 HP to 30 HP |
| 46 | 30 HP to 50 HP |
| 47 | Above 50 HP to 100 HP |
| 48 | Shaft with Sleeve Chuck Nut |
| 49 | 5 HP to 20 HP |
| 50 | 20 HP to 30 HP |
| 51 | 30 HP to 50 HP |
| 52 | Above 50 HP to 275 HP |
| 53 | Bush Shaft Sleeve of G.M. |
| 54 | 5 HP to 20 HP |
| 55 | 20 HP to 30 HP |
| 56 | 30 HP to 50 HP |
| 57 | Above 50 HP to 100 HP |
| 58 | G.M. Gland Cover |
| 59 | 5 HP to 20 HP |
| 60 | S.S. Shaft (Non Magnetic) |
| 61 | 5 HP to 20 HP |
| 62 | 20 HP to 30 HP |
| 63 | 30 HP to 50 HP |
| 64 | Above 50 HP to 100 HP |
| 65 | M.S. Shaft Check Nut |
| 66 | 5 HP to 20 HP |
| 67 | 20 HP to 30 HP |
| 68 | 30 HP to 50 HP |
| 69 | Above 50 HP to 100 HP |
| 70 | JOB WORK FOR REPAIR OF PUMP MOTOR |
| 71 | Bearing Housing (rebuilding, turning & finishing) |
| 72 | 5 HP to 20 HP |
| 73 | 20 HP to 30 HP |
| 74 | 30 HP to 50 HP |
| 75 | Above 50 HP to 100 HP |
| 76 | Bearing Cap (rebuilding, turning & finishing) |
| 77 | 5 HP to 20 HP |
| 78 | 20 HP to 30 HP |
| 79 | 30 HP to 50 HP |
| 80 | Above 50 HP to 100 HP |
| 81 | Impeller Reconditioning for all type of Pump |
| 82 | 5 HP to 20 HP |
| 83 | 20 HP to 30 HP |
| 84 | 30 HP to 50 HP |
| 85 | Above 50 HP to 100 HP |
| 86 | Labour Charges for Dismantling & Assembling of Pump |
| 87 | 5 HP to 20 HP |
| 88 | 20 HP to 30 HP |
| 89 | 30 HP to 50 HP |
| 90 | Above 50 HP to 100 HP |
| 91 | Coupling with stud and rubber bush |
| 92 | 5 HP to 20 HP |
| 93 | 20 HP to 30 HP |
| 94 | 30 HP to 50 HP |
| 95 | Above 50 HP to 100 HP |
| 96 | Supply & Fixing of tyre coupling sets according to relevant IS code in Centrifugal couple pump sets of approved make Unit. This job also included re-alignment of centrifugal couple pump set after fixing of tyre coupling set as per directed by Engineer-in charge. |
| 97 | Type 14 Nos. set |
| 98 | Type 15 Nos. set |
| 99 | Type 16 Nos. set |
| 100 | Type 17 Nos. set |
| 101 | Supply and fixing Ball bearing of Various size for centrifugal/monoblock pump set of ISI Mark as per specification and approved make by EIC. |
| 102 | 6305 or equivalent size |
| 103 | 6306 or equivalent size |
| 104 | 6307 or equivalent size |
| 105 | 6308 or equivalent size |
| 106 | 6309 or equivalent size |
| 107 | 6310 or equivalent size |
| 108 | 6311 or equivalent size |
| 109 | 6312 or equivalent size |
| 110 | 6316 or equivalent size |
| 111 | 6317 or equivalent size |
| 112 | Routine maintenance of centrifugal coupled pump and motor including opening, cleaning, greasing and refitting / changing of ball bearing if required, gland refilling and replacing all rusted studs, replacing rubber bushes & coupling nut & bolts for coupling pulley, tightening all nut & bolts of foundation, baseplate, pump & motor etc. Checking & correcting alignment of pump & motor including necessary materials i.e. grease, nut & bolts, studs, washers, gland packing and rubber bushes etc. work done at site complete job |
| 113 | 5 HP to 20 HP |
| 114 | 20 HP to 30 HP |
| 115 | Above 30 HP and up to 50 HP |
| 116 | Above 50 HP and up to 100 HP |
| 117 | Cleaning of pump house by air blower/ vacuum cleaner or other means including removing of JALA from ceiling and walls etc. complete Job. |
| 118 | Cleaning of Electric Panel PMCC by air blower/vacuum cleaner or other means including tightening of loose connections etc. complete job. |
| 119 | Replacing of damaged/broken gland packing plate with new gland packing plate suitable for centrifugal pump shafts and nut&bolts etc. complete job. |
| 120 | 5 HP to 20 HP |
| 121 | Above 20 HP and up to 30 HP |
| 122 | Above 30 HP and up to 50 HP |
| 123 | Above 50 HP and up to 100 HP |
| 124 | Turning of various sizes of CID Joints Class- 10/ 15 Complete set (Labour Charges), The Joints will be supplied by the Junior Engineer concern of Department and carting to workshop and after turning of these joints, firm is liable to transport upto Junior Engineer concern's store own his cost. |
| 125 | 80 mm dia |
| 126 | 150 mm dia |
| 127 | 200 mm dia |
| 128 | 250 mm dia |
| 129 | 300 mm dia |
| 130 | Providing, Fabrication of Mild Steel Plane Ended/ Flanged Specials like Tees, Bends, Reducers, Enlargers, Plugs, Tail Pieces and Blank Flange made from MS pipes, MS sheet strip and MS Sheet of required sizes by welding, cutting and treading as per site conditions and as directed by the Engineer- In- Charge complete in all respect. |
| 131 | Supplying and fixing of MS Rods for different sizes of sluice valve and should be supplied as according to size of old rods including material and finishing for the following sizes. |
| 132 | Sluice Valve Size 80mm |
| 133 | Sluice Valve Size 100mm |
| 134 | Sluice Valve Size 125mm |
| 135 | Sluice Valve Size 150mm |
| 136 | Sluice Valve Size 200mm |
| 137 | Sluice Valve Size 250mm |
| 138 | Sluice Valve Size 300mm |
| 139 | Supplying of Chuck Nut for different sizes of sluice valve and should be supplied as according to size of Check Nut including material for the following sizes. |
| 140 | Sluice Valve Size 80mm |
| 141 | Sluice Valve Size 100mm |
| 142 | Sluice Valve Size 125mm |
| 143 | Sluice Valve Size 150mm |
| 144 | Sluice Valve Size 200mm |
| 145 | Sluice Valve Size 250mm |
| 146 | Sluice Valve Size 300mm |
| 147 | Providing of U Plate (U Stand) for different sizes of sluice valve and should be supplied as according to size of old U Plate including material for the following sizes. |
| 148 | Sluice Valve Size 80mm |
| 149 | Sluice Valve Size 100mm |
| 150 | Sluice Valve Size 125mm |
| 151 | Sluice Valve Size 150mm |
| 152 | Sluice Valve Size 200mm |
| 153 | Sluice Valve Size 250mm |
| 154 | Sluice Valve Size 300mm Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 12, 2026
11:30 IST
Tender Published
Tender notice published.
Completed
Aug 20, 2026
18:00 IST
Corrigendum-1 Issued
Clarifications on tender conditions and amendments issued.
Upcoming · 5 daysAug 20, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 5 daysAug 21, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 6 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender