Tender For Uws Schemes At Udaipur /Sh:- Renovation Of Existing Semi Permanent Pump House, Installation Of Pump Motor Set, Extension Of Pipeline As Required In/C. All Other Allied Works Complete At Dtw 7 Near Northern Side Of Tripura Sundari Sub-Divis
Tender Value
6.37 Lakhs
Estimated cost
Bid Submission
11 Aug 2026
1 days left
EMD
12744
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Gomati → Tripura
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Uws Schemes At Udaipur /Sh:- Renovation Of Existing Semi Permanent Pump House, Installation Of Pump Motor Set, Extension Of Pipeline As Required In/C. All Other Allied Works Complete At Dtw 7 Near Northern Side Of Tripura Sundari Sub-Divisional Hospital Under Dws Sub-Division No. I Udaipur, Gomati Tripura.
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.-All kinds of soil |
| 2 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. All kind of soil |
| 3 | Demolishing cement concrete manually / by mechanical means including disposal of material with all lifts and upto 50 m lead etc. complete as per direction of the Engineer- in-charge:- Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 4 | Supplying and filling in plinth, under floor, foundations etc. with sand (fine) from local quarry with all lifts including spreading in horizontal layers, watering, grading to required slope, ramming, consolidating and compacting each layer by using plate compactor or by any suitable method complete. |
| 5 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - i) 1:4:8 ( 1 Cement: 4 fine sand : 8 graded well burnt brick aggregate 40 mm nominal size) |
| 6 | ii) 1:2:4 ( 1 Cement: 2 fine sand : 4 graded well burnt brick aggregate 20 mm nominal size) |
| 7 | iii) 1:3:6 ( 1 Cement: 3 fine sand : 6 graded well burnt brick aggregate 20 mm nominal size) |
| 8 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement- -All work upto plinth level: i) 1:2:4 ( 1 Cement: 2 fine sand : 4 graded well burnt brick aggregate 20 mm nominal size) |
| 9 | Centering shuttering including struttings, propping etc. and removal of form work for:i) Foundations, footings, bases for columns etc. for mass concrete with timber plank |
| 10 | ii) Columns, Pillars, Piers, Abutments, Posts and Struts with wooden plank |
| 11 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and skirting courses, fillets, columns, pillars, piers, abutments, posts and struts etc. upto floor five level excluding cost of centring, shuttering, finishing and reinforcement- i) 1:2:4 ( 1 Cement: 2 fine sand : 4 graded well burnt brick aggregate 20 mm nominal size) |
| 12 | Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 13 | Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 14 | First class brick work in foundation and plinth including cost of all materials as required complete:- i) In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 15 | First class brick work in superstructure above plinth level & upto floor-five level including cost of all materials as required complete:- i) In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 16 | Half brick masonry work with first class bricks in superstructure upto floor five level including cost of all materials as required complete:- i) In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 17 | Dismantling old plaster or pointing, raking out joints, cleaning and preparing the surface for re-plastering or re-pointing including disposal of rubbish to the dumping ground with all leads and lifts etc.complete as per direction of the Engineer- in-charge. |
| 18 | Constructing masonry Chamber 120 x 120 x 100 cm, inside with 75 class designation brick work in cement mortar 1 : 4 ( 1 cement : 4 fine sand ) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside ) with chained lid and RCC top slab 1 : 2 : 4 mix ( 1 cement : 2 fine sand : 4 brick aggregate 1st class 20 mm nominal size ) necessary excavation foundation concrete 1 : 5 : 10 ( 1 cement : 5 fine sand : 10 brick aggregate 1st class 40 mm nominal size ) and inside plastering with cement mortar 1 : 3 ( 1 cement : 3 fine sand ) 12 mm thick finished with a floating coat of neat cement complete as per standard design.A. with second class bricks |
| 19 | 12 mm cement plaster of mix i) In cement mortar 1:4(1 cement : 4 fine sand) |
| 20 | 15 mm cement plaster on the rough side of single or half brick wall of mix: Cement mortar 1:4 (1 cement : 4 fine sand) |
| 21 | Neat cement punning. |
| 22 | Providing and laying cement concrete 1:2:4 (1 cement: 2 fine sand : 4 graded well burnt brick aggregate) flooring finished with a floating coat of neat cement including cement slurry, rounding of edges and strips and cost of glass strips etc. all complete as per direction of Engineer in-charge. 40mm thick. |
| 23 | Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete |
| 24 | Distempering with dry distemper of approved brand and manufacture and of required shade on old work ( one or more coats ), to give an even shade as required complete as per direction of the Engineer in charge. |
| 25 | Finishing walls with acrylic smooth exterior paint of required shade of approved brand and manufacture on old work ( one or more coats ) including preparation of surface as required complete as per direction of the Engineer in charge. |
| 26 | Dismantling doors,windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area 3 sqm and below. |
| 27 | Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6mm angle iron and 3mm M.S. gusset plates at the junctions and corners, & with cleats with bolts & nuts, rivets, locking arrangement, handles, hooks & eyes, pinlets including embedding in cement concrete of required grade for fixing in position, all necessary fittings, including applying a priming coat of approved steel primer etc. complete as required:- Using M.S. angels 40x40x6 mm for diagonal braces |
| 28 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer]: Two or more coats on new work over an under coat of suitable shade with ordinary paint (primer) of approved brand and manufacture |
| 29 | Making plinth protection 50 mm thick of cement concrete 1 : 3 : 6 ( 1 cement : 3 fine sand : 6 graded well burnt brick aggregate 20 mm nominal size ) over 75mm bed of dry brick ballast 40 mm nominal size well rammed and cosolidated and grouted with fine sand including finishing the top smooth. |
| 30 | Providing and fixing C.I. non-return valve of approved quality as per CPWD specification and direction of the Engineer - in - charge. i) 100 mm nominal bore |
| 31 | Excavating trenches of required width for pipes, cables etc. including exacavation for sockets, dressing of sides where required, ramming of bottoms, depth upto 1500 mm including getting out the excavated soil and backfilling of soil as required after laying of pipeline, in layers not exceeding 200 mm in depth including consolidating each deposited layer by ramming, watering etc. and disposing of surplus excavated soil with all required leads as per Chapter - 2 of CPWD specification and direction of the Engineer - in - charge.A) For GI/CI/DI pipes in new workIn all kind of soili) For pipes exceeding 90 mm dia but not exceeding 300 mm dia. |
| 32 | Providing and laying S & S Centrifugally Cast ( Spun ) Ductile Iron Class K-7 Pipes conforming to IS : 8329 as per CPWD specification and direction of the Engineer - in - charge. i) 100 mm dia Ductile Iron Class K-7 pipes |
| 33 | ii) 150 mm dia Ductile Iron Class K-7 pipes |
| 34 | Providing and fixing DI specials as per CPWD specification and direction of the Engineer - in - charge. A. DI all socketted bend 45 degreei) 125 mm dia |
| 35 | B. DI all socketted tee ii) 150 x 150 x 150 mm dia |
| 36 | C. DI Double socketted tapperi) 150 x 125/100 mm dia |
| 37 | D. DI Flange socketted tail pice i)125 mm dia |
| 38 | ii) 150 mm dia |
| 39 | Providing and fixing of C.I. Sluice valves(with cap) complete with bolts, nuts, rubber insertions etc.(the tail piece if required will be paid separately) as per CPWD specification and direction of the Engineer-in-charge.i) 125 mm dia. A. PN - 1.6 |
| 40 | ii) 150 mm dia. A. PN - 1.6 |
| 41 | Providing and fitting fixing of 10,000 GPH Capacity & 20 HP, 76m Head minimum 3 star rating water lubricated submersible pump motor set of maximum 150/200mm outer dia. With maximum 8(eight) stages coupled with required water & non-over loading submersible pump & motor suitable for 340-440 volts,3 phase 50Hz A.C supply and star delta method of starting, along with 35m 1x2x3x10 sq.mm joint less PVC 3(three) core double length flat cable(continuous length) of suitable size fitted with submersible motor, suction case, strainer, coupling key, vertical non-return valve cum discharge case in/c supplying of 10Nos. suitable guard with clips & nuts &bolts,2(two) pair M.S column clamps in/c. installation of submersible pump and motor upto the depth of 100 ft by GI pipe(conforming to IS: 1239 medium class) for column assembly which will be supplied by the agency at his own cost as per direction of the Engineer-in-charge conforming to the terms & conditions of the contract(Each pump with motor shall consist of Stainless closed type impeller, C.I bowl, C.I discharge case, pump shaft(Stainless Steel), bush(Bronze), Shaft sleeve(Bronze/chromium),sand guard, winding motor, stator, counter thrust plate, thrust plate, thrust bearing segment etc conforming to related BIS codes) (GI Falnge, GI column pipe will be issued by the Department at free of cost.) |
| 42 | Providing and fabrication of column pipe including fitting fixing of G.I flange by cutting the G.I pipe (conforming to IS:1239 medium class) into 3.05m long and welding the same with G.I flange as per specification and direction of the Engineer-in-charge(G.I pipe will be provided by the agency at his own cost & risk). iv.For 100 mm dia G.I pipe with 10mm thick G.I flange |
| 43 | Providing and fitting fixing of 3 phase indicating lamp fitted with panel board with three different colour lamps with batten holder complete as per specification and direction of the Engineer – in – charge. |
| 44 | Providing and fitting fixing of pressure meter ( 0.0 - 14.0 Kg/sqcm.) as per relevant IS specification and the direction of the Engineer - in-charge. |
| 45 | Providing 3 – phase wiring of the electric energy meter switch fuse unit capacitor, star delta starter, motor etc. with 7/10 size copper wire and wiring of volt meter, amp meter, electric switch etc. as per direction of the Engineer-in-charge. |
| 46 | Providing internal electrification of the pump house with 2 (two) light points (inside and outside) one celling fan point with individual switch controlled by one standard with proper earthing and complete wiring with 1.5 mtr. single core aluminum wire in/c. the cost of wooden board, batten switch holders etc. complete. |
| 47 | Supplying of ISI marked/Taparia make tools for water supply scheme.i) Sly Wrenche (12\\") |
| 48 | ii) Screw Driver |
| 49 | iii) pliers |
| 50 | Supplying of armed plastic chair( Supreme/Nilkamal make)for different W/S scheme. |
| 51 | Supplying of plastic table(supreme make) for water supply scheme at the work site as per specification and direction of the Engineer-in-charge. |
| 52 | Providing and fitting fixing with PVC insulated single core multistand copper cable conforming to IS :694 inter connection with all electrical equipements of the panel board as per specification and direction of the E-in-charge. (in mtrs) 35 Sq mm |
| 53 | Providing and fitting fixing of 6 feet x 4 feet x 1 inch( thickness) Gamair wood / plywood panel board for fitting fixing of electrical items, in/c 2 nos. MS angle post( size 2 inch x 2 inch x 9 feet), nuts & bolts etc for errectin of the same by 1:1.5:3 cement conrete casting(1 feet x 1 feet x 2 feet) below the ground level and painting two or more coats & plastic paint as per specification and direction of the E-in-charge. |
| 54 | Supplying of 1200 mm Sweep white colour AC ceiling fan capacitor type double ball bearing complete with 300 mm down rod, canopies, shackles , three nos. blades( Without regulator) confirming to IS 374 (1979), BEE -5 Star |
| 55 | Grading roof for water proofing treatment complete as required as per dirrection of E-in- Charge. i) cement concrete 1:2:4 (1 cement : 2 fine sand: 4 graded stone aggregate 20 mm nominal Size) Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 05, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 11, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 1 dayAug 11, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 1 dayTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender