Tender For Renovation Work Of Ad, Ld And Reception At Nift Delhi C Us New Delhi
Tender Value
35.36 Lakhs
Estimated cost
Bid Submission
17 Aug 2026
3 days left
EMD
80000
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Delhi → Delhi
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Renovation Work Of Ad, Ld And Reception At Nift Delhi C Us New Delhi
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling wooden boarding’s in lining of walls and partitions, excluding supporting members but including stacking within 50 metres lead: Thickness above 25 mm or more |
| 2 | Dismantling aluminum/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable materialand stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge. |
| 3 | Dismantling of the Spilt / Window/ Ductable ac including cu pipe, drain, Duct, cable, indoor, outdoor etc and shift it to the basement or designated place as directed by the Engineer-in charge. |
| 4 | Removing of the entire Electrical wiring/ cabling of proposed area of LD and AD department |
| 5 | Dismantling steel work in single sections including dismembering and stacking within 50 meters lead in: Channels, angles, tees and flats |
| 6 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 meters lead as per direction of Engineer - in - charge. Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix) |
| 7 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm center to center, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts,12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks) |
| 8 | Providing and fixing 15 mm thick false ceiling tiles at all heights with integral densified calcium silicate reinforced with fiber and natural filler false ceiling tiles of Size 595x595 mm of approved texture, design andpatterns having NRC (Noise Reduction coefficient) of 0.50 (minimum) asper IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity < 0.043 W/m K asper ASTM 518:1991,in true horizontal level on the existing frame work consisting of T-sections and L sections suitably fixed according to tile size as per direction of Engineer-in-charge. |
| 9 | Providing and fixing of 12 mm thick toughened glass partition with glass of M/s Saint- Gobain/ M/s Modi Guard/ M/s Asahi make, using U Channel OGL-PR-11 (Ozone make) with S.S. flip cover, to be fixed to floor and wall using suitable approved S.S. rawl plugs/ anchor bolts at a maximum distance of 600mm c/c, and sealing the joint with approved make of silicone sealant (Dow corning/equivalent make) . The Glass to be etched/ frosted film pasted/text to be written on it as per drawing provided or as directed by NIB, complete work |
| 10 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing , polishing and making curvature ( wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc, of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Enginner- in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) |
| 11 | Providing and fixing of 12 mm thick toughened glass partition with glas of M/s Saint- Gobain/ M/s Modi Guard/ M/s Asahi make, including providing double action hydraulic floor spring & its type fiixng arrangement of M/s Ozone /equivalent make and making necessary holes etc. for fixing required door fittings, all complete as per direction of engineer in charge ( Door handle, lock and stopper etc. to be paid for separately). |
| 12 | Providing & fixing Glass Door Stainless (ss) patch Lock with strike plate. Material : Stainless steel 304 grade & Glass Door's thickness : 8 mm to 12 mm, as directed by Engineer-in charge. |
| 13 | Providing & fixing H-Type Stainless Steel Handles of size : 20 mm X 150mm on both side of glass door of M/s Ozone/ EBCO make equivalent all complete, as directed by Engineer-in charge. |
| 14 | Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : Powder coated aluminium (minimum thickness of powder coating 50 micron). |
| 15 | For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron). |
| 16 | Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in paneling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer-in- charge. Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side. |
| 17 | Providing and fixing glazing in aluminum/ wooden door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminum snap beading shall be paid in basic item): With float glass panes (film/ designer as approved byb the engineer-in-charge) of 5 mm thickness (weight not less than 12.50 kg/sqm). |
| 18 | Filling the gap in between aluminum frame & adjacent RCC/ Brick/Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. Up to 5mm depth and 5 mm width. |
| 19 | Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. |
| 20 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 21 | Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre. |
| 22 | Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade : Two or more coats on new work |
| 23 | Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete. |
| 24 | Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 250x10 mm. |
| 25 | French spirit polishing :One or more coats on old work. |
| 26 | Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete : 125x64x1.90 mm. |
| 27 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). Sal wood. |
| 28 | Providing and fixing wooden storage (overhead/ almirah) with 19 mm commercial board with laminate finish (both -inside and out sides) of approx depth 0.7M size work includes all hardware fittngs requires such as Hinges, handels, locks, etc items required during execution of work complete in all respect as per the directions of Engg-In-Charge. |
| 29 | Providing & Fixing of rolling Blinds (Make - Vista or equivalent), Translucent/Blackout as per the user choice, work should be complete in all respect such as fixing, cutting, etc as per items required during execution of work complete in all respect as per the directions of Engg-In-Charge. |
| 30 | Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (with the cost of chemical emulsion) : Treatment at points of contact of wood work by chemical emulsion Chlorpyriphos (in oil or kerosene based solution) @ 0.5 litres per hole by drilling 6 mm dia holes at downward and Treatment of existing masonry using chemical emulsion @ one litre per hole at 300 mm interval including drilling holes at 45 degree and plugging them with cement mortar 1:2 (1 cement : 2 coarse sand) to the full depth of the hole : With Chlorpyriphos E.C. 20% with 1% concentration |
| 31 | Providing & fixing wooden soft board made from 6mm thk. Comm. Back ply over pasted /holded 15 mm thk. Sitatek sandwich soft board /pin board covered with PVC laminated superfine hessian jute facbric with side covered 75x15 mm wide solid wood tapper molding & 50 mm wide TEAK WOOD leaping in center of board with melamine polishing with required Ms holding clamps complete in all respect. As per specification and direction of the ENgineer-in-charge Payment will be made on the basis of actual Measurement of work at different location or different floors height. |
| 32 | Providing and fixing bright finished Aluminum/ SS handles with screws etc.complete: 150-200 mm. |
| 33 | Providing & Fixing of door closer in the aluminum doors . ( Make :- Ozone/Kich/ Doorset/Insta or equivalent) suitable for full height/ half height doors |
| 34 | Providing and fixing precoated galvanized iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 35 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 36 | 15 mm cement plaster on rough side of single or half brick wall of mix: 1:4 (1 cement: 4 coarse sand) |
| 37 | 12 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand) |
| 38 | Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : |
| 39 | Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specification. |
| 40 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand),jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm |
| 41 | Washed stone grit plaster on exterior walls height upto 10 metre above ground level, in two layers, under layer 12 mm cement plaster 1:4 (1 cement : 4 coarse sand ), furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 2 Kg of cement per square metre, top layer 15 mm cement plaster 1:1/ 2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10 mm nominal size), in panels with groove all around as per approved pattern, includingscrubbing and washing the top layer with brushes and water to expose the stone chippings ,complete as per specification and direction of Engineer-in-charge (payment for providing grooves shall be made separately). |
| 42 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 43 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 44 | Supplying and installation wiring for circuit/ sub main along with with the following sizes of FRLS PVC insulated copper ( Anchor/V- guard/ Havells/ Polycab make) single core cable in surface/ recessed in pvc conduit/ Channel of required size from existing DB to the cabins, through wall/ floor ( concealed in wall using conduits 25 mm diameter or higher dia. as required) including chaisng using electric cutter and subsequent filling and repairing using 1:6 (1 cement, 6 find sand) plaster to give a neat finish, and finishing in matching paint on top, and through the existing metal false ceiling/gypsum false ceiling, by carefully removing the existing panels/ making holes for passage, laying of conduits, placing the wires in conduits (flexible / otherwise), securely fastened to wall/ ceiling using suitable brackets / ties etc and subsequent refixing of ceiling panel/ repairing the gypsum ceiling with existing specifications to return the ceiling to its original position all complete. Any repairs resulting out of the above shall be included in this item. Following cores of wires to be provided. |
| 45 | 1) 1 x 1.5 sq.mm (L& N) |
| 46 | 2) 2x1.5 sq mm + 1x1.5 sq mm earth wire. |
| 47 | 3) 2x2.5 sq mm + 1x 1.5 sq mm earth wire. |
| 48 | 4) 2x 4 sq mm + 1x 1.5 sq mm earth wire. |
| 49 | Supplying and fixing suitable size PVC box with modular plate and cover in front on surface or in recess as required, including and fixing 02 nos 5 pin 5/6 & 1 no 15/16 amps, modular socket outlet and 15/16 amps modular switch, connection etc as required, complete in all respect and as per direction of Engineer-in-charge. |
| 50 | Supplying and fixing different size PVC box with modular plate and cover in front on surface or in recess, including modular switch 6A, connection etc as required. Payment will be release as per total numbers of switches |
| 51 | Supplying and fixing different size PVC box with modular plate and cover in front on surface or in recess, including modular switch 16A, connection etc as required. Payment will be release as per total numbers of switches |
| 52 | Supplying and fixing different size PVC box with modular plate and cover in front on surface or in recess, including modular socket 16A, connection etc as required. Payment will be release as per total numbers of sockets |
| 53 | Supplying and fixing different size PVC box with modular plate and cover in front on surface or in recess, including modular socket 6A, connection etc as required. Payment will be release as per total numbers of sockets |
| 54 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface / recess including cutting the wall and making good the same in case of recessed conduit as required 20 mm dia. |
| 55 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface / recess including cutting the wall and making good the same in case of recessed conduit as required 25 mm dia. |
| 56 | Supplying and installation of Telephone sockets including embedded box, cover plate etc (modular) all complete north west make) |
| 57 | Supplying and drawing 2 Pair 0.5 mm dia FRLS PVC insulated annealed cooper conductor, unaroured telephone cable in the existing surface/ recessed steel/ PVC conduit as required |
| 58 | Providing and installation of CAT-6A wiring for LAN points with PVC sheathed anneaked tinned copper conductor CAT-6A wire confirming to ITD-S/ SW- 113B in 20 mm dia 16SWG/ surface/ concealed conduit upto LAN Switch inclduing cost of providing saddles etc. as required for surface/ flush and the cost of cutting and fixing of outlet RJ-45 with GI outlet box along with cover plate complete as required including crimping and jack etc. This shall include installation of wire through the existing false ceiling and in the concealed conduits/ PVC Channel/ Flexible Pipe in walls ( Cost to be included). This shall also include the repair work/ making good any damage/ breakage done to the walls / ceiling or any other route, in the existing specifications so as to give a complete and neat look. Above including the cost of cutting and fixing of telephone cord outlet RJ- 4 with GI outlet box along with cover plate complete as required including crimping and jack etc . |
| 59 | SITC of 2x2 panel LED, 36W, Output >3500 lm, 6000/6500K, Min. 3kv inbuilt surge protection, Beam Angle >110 degree, PF > 0.95, anti glare diffuser, with High power SMD OSRAM/EDISON LED (Make- Bajaj/Havells /Syska /Philips/Inferno/ CG/C&S) in the false ceiling. The cost should be inclusive of cutting of false ceiling, providing support to false ceiling, frame work, installation of light, electrical connections of the lights with existing switchboard and making surface good including paint work. |
| 60 | Supply, installation, testing & commissioning of surface panel 15/18/20W LED lights , 6000/6500K, lumen output- min 85lm/watt, surge protection upto min 3kv, Power factor >0.9, anti glare diffuser with High power SMD OSRAM/EDISON LED (Make : Bajaj/Havells /Syska /Philips/Inferno/ CG/C&S ). The cost should be inclusive of installation of light, electrical connections of the lights with existing switchboard and making surface good including paint work. |
| 61 | Supply, installation, testing & commissioning of surface panel 40-50W LED lights , 6000/6500K, lumen output- min 85lm/watt, surge protection upto min 3kv, Power factor >0.9 anti glare difuser with High power SMD OSRAM/EDISON LED (Make : Bajaj/Havells /Syska /Philips/Inferno/ CG/C&S ). The cost should be inclusive of installation of light, electrical connections of the lights with existing switchboard and making surface good including paint work. |
| 62 | Supply, installation, testing & commissioning of recess panel 40-50W LED lights , 6000/6500K, lumen output- min 85lm/watt, surge protection upto min 3kv, Power factor >0.9 anti glare difuser with High power SMD OSRAM/EDISON LED (Make : Bajaj/Havells /Syska /Philips/Inferno/ CG/C&S ). The cost should be inclusive of cutting of false ceiling, providing support to false ceiling, frame work, installation of light, electrical connections of the lights with existing switchboard and making surface good including paint work. |
| 63 | SITC of recess mounted LED lights (round) for low ceiling height application, 15/18 W, 6500K lumen output- min 85lm/watt, surge protection upto min 3kv, Power factor >0.9 anti glare difuser with High power SMD OSRAM/EDISON LED (Make : Bajaj/Havells /Syska /Philips/Inferno/ CG/C&S ). The cost should be inclusive of cutting/repairing of false ceiling, providing support to false ceiling, frame work, installation of light, electrical connections of the lights with existing switchboard and making surface good including paint work. |
| 64 | SITC of recess mounted LED lights (round) for false ceiling 6W, 4000K surge protection upto min 3kv, Power factor >0.9 anti glare difuser with High power SMD OSRAM/EDISON LED (Make : Bajaj/Havells /Syska /Philips/Inferno/ CG/C&S ). The cost should be inclusive of cutting/repairing of false ceiling, providing support to false ceiling, frame work, installation of light, electrical connections of the lights with existing switchboard and making surface good including paint work. |
| 65 | Supply of ultra slim linear LED lighting fixtures 9W/10, 6000K for work stations and smaller areas(Make : Bajaj/Havells /Syska /Philips/Inferno/ CG/C&S ) |
| 66 | Supply of ultra slim linear LED lighting fixtures 18W/20, 6000K for replacement of faulty 40W fluorescent lights (Make : Bajaj/Havells /Syska /Philips/Inferno/ CG/C&S ) |
| 67 | Providing and fixing of Wall fan 400 mm (CG/Havells/ USHA/ Bajaj) including connection |
| 68 | Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transportincluding loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, completeas per directions of Engineer-in-charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 05, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 17, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 3 daysAug 18, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 4 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender