Tender For Repairs To Drain, Hardstanding, Path And Paver Blocks At Site A2 Of Naval Base Area Karwar.
Tender Value
50 Lakhs
Estimated cost
Bid Submission
26 Aug 2026
2 days left
EMD
1 Lakhs
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Uttara Kannada → Karnataka
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repairs To Drain, Hardstanding, Path And Paver Blocks At Site A2 Of Naval Base Area Karwar.
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of unreinforced cement concrete of any description and in any position not otherwise specifically provided for etc complete all as specified and directed. |
| 2 | Demolition of reinforced cement concrete in ground floors and paving not exceeding 15 cm thickness (below or above ground level) all as directed. Note:- Reinforcement shall be cut as required to facilitate demolition |
| 3 | Demolition of stone slabs and tiles of any description or thickness in floor, aprons etc laid bedded and pointed in any mortar all as specified and directed |
| 4 | Demolition of concrete block walling, brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars etc, but excluding ashlars facings, dressed stonework and precast concrete articles etc all as specified and directed. |
| 5 | Dismantling of stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars etc, but excluding ashlars facings, dressed stonework etc all as specified and directed. |
| 6 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed |
| 7 | M&L for PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in foundations, filling and mass concrete complete all as specified and directed |
| 8 | M&L for machine pressed pre-cast concrete interlocking coloured paver block of any size and shape conforming to IS-15658-2006 of 60mm thickness M-35 grade with grey cement and pigment etc complete all as specified and directed. |
| 9 | M&L for stone dust or sand base filling in floors or pavings, laid in layers n exc.15 cm thick, spread, levelled, and blinded with earth and rammed including watering etc complete all as specified and directed. |
| 10 | M&L for cement concrete tiles 30cmx30cmx 20-22mm thick, machine pressed, (with grey cement and no pigments), set jointed and pointed in neat cement slurry in floors over and including 15mm thick bedding layers in CM 1:6 all as specified & directed |
| 11 | M&L for PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in kerbing all around of tile etc complete all as specified and directed. |
| 12 | M&L for providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3, including making joints with or without grooves (thickness of joints except at sharp curve shall not be more than 5 mm), including making drainage opening wherever required complete all as specified and directed. |
| 13 | M&L for preparing of new brick, stone, concrete or plastered surfaces of any description over 10cm girth or width, not otherwise described and applying two coats of synthetic enamel paint using mechanical spray (maximum working pressure of 3300 PSI) over priming paints plaster coats all as specified and directed. |
| 14 | M&L for preparing of old brick, stone, concrete or plastered surfaces of any description over 10cm girth or width, not otherwise described and applying one coat of synthetic enamel paint using mechanical spray (maximum working pressure of 3300 PSI) all as specified and directed. |
| 15 | M&L for providing 100mm thick plain cement concrete 1:2:4, type B-1, using 20mm graded stone aggregate laid in flooring (if required laid in alternate panels) including finishing the surface even and smooth without using extra cement etc complete all as specified and directed. |
| 16 | M&L for providing precast cement concrete block masonry with solid blocks exc 10 cm width, type C-1 (1:3:6) using 20mm graded stone aggregate and set in cement mortar 1:6 all as specified and directed. |
| 17 | M&L for walling of random rubble masonry uncoursed, well bounded, bedded and solidly hearted built in cement mortar 1:6 all as specified and directed. |
| 18 | All as per Item No.17 above but except stones. |
| 19 | M&L for flush pointing to block in course or ashlar masonry or concrete block walling in CM 1:4 complete all as specified and directed. |
| 20 | M&L for rendering 15mm thick in CM 1:4 on fair faces of concrete surfaces and finished even and smooth without using extra cement including necessary scaffolding and safety measures as required all as specified and directed. |
| 21 | M&L for preparation of new plastered / decorated wall surfaces applying two coats of acrylic emulsion exterior grade paint by using airless spray (maximum working pressure of 3300 PSI) over a coat of primer including necessary scaffolding and safety measures as required etc complete all as specified and as directed. |
| 22 | M&L for precast cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate set in cement mortar 1:6 work for landings, cover slabs, manholes, chajjas, water troughs, manger, shelves and similar articles with plain faces complete all as specified and as directed |
| 23 | M&L for mild steel TMT (CRS/ HCRM) bars 10mm dia and over cut to length bent shape as required including cranking bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to Fe-410-S complete all as specified and as directed. |
| 24 | M&L mild steel TMT (CRS/ HCRM) bars 6 to 8mm dia and over cut to length bent shape as required including cranking bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to Fe-410-S complete all as specified and as directed. |
| 25 | S&F framed work such as grills, gratings, sun shed etc with ends of bars shouldered and/or riveted or welded, or forged into spikes, framed guard bars, barred iron doors, ladders, farmed balusters, walk ways, railings, frame work of water tanks and similar work conforming to Fe-410-0 or Fe-310-0 complete all as specified and directed. |
| 26 | M&L for preparing new or previously untreated surface of any description, over 10cm in width or girth and applying two coats of synthetic enamel paint by using airless spray (maximum working pressure of 3300 PSI) over one coat of red oxide primer complete all as specified and directed. |
| 27 | M&L for preparing old or previously treated surface of any description, over 10cm in width or girth and applying one coat of synthetic enamel paint by using airless spray (maximum working pressure of 3300 PSI) etc complete all as specified and directed. |
| 28 | M&L for 75mm thick PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in hard standing/ plinth protection and finishing the concrete surface even and smooth without using extra cement complete all as specified and directed. |
| 29 | M&L for hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embedding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 etc complete all as specified and directed. |
| 30 | Supply only chain link mild steel galvanised fencing any size or type complete all as specified and directed. |
| 31 | Fixing only chain link fencing confirming to IS 2721: 2003 including line wires, any mesh, size to any type of standards, rails, straining bolts, etc., including provision of binding wire complete all as specified and directed. |
| 32 | S&F MS flat fixed to Post/Vertical members including securing bolts for chain link fencing etc complete all as specified and directed. |
| 33 | S&F mild steel round bars 10mm dia and over for securing chain link fencing cut to length bent to shape required including bolting etc complete confirming to Fe 290 Gde E-165 all as specified and directed |
| 34 | Removing excavated soil/ material to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 05, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 26, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 2 daysAug 28, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 4 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender