Tender For Repair To Runway Surface, Dispersal, Ptt By Using Pme And Moss Removal At installation Hansa Under Ge (Nw) Vasco
Tender Value
94.99 Lakhs
Estimated cost
Bid Submission
18 Aug 2026
12 days left
EMD
1.67 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
goa → Goa
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair To Runway Surface, Dispersal, Ptt By Using Pme And Moss Removal At installation Hansa Under Ge (Nw) Vasco
BOQ
| Sl. No. | Item Description |
| 1 | M&L for preparation of old black top surface by brushing with wire brushes for removing caked mud etc sweeping with brooms and finally fanning the cleaned surface with air blower to remove loose dirt etc. complete and apply cold polymer modified emulsion (PME) by using mechanical spraying of total cold liquid PME 1 ltr per sqm (undiluted) for two coats with mineral filler as recommended by manufacturer of PME (after diluting with water), each coat diluted in the ratio 1:1 (PME: WATER) and ensure uniform finish of applied flight strips complete all as per manufactcurer instructions all as specified and directed by Engr-in-Charge |
| 2 | Note: The tenderer shall take into consideration for the following points while quoating for the tender(a) Due care shall be taken for friction parameters during application of PME as per ICAO DOC 9137 Part 2 standard. For the value range of the coefficient of friction post application of Polymer modified Emulsion (PME) please ref to table No. 3.1 of ICAO DOC 9137 Part 2. (b) The work shall be carried out through authorized and qualified applicators of the manufacturer. The manufacturer of PME available in the market specifies exact mixing ratios of water and their respective compounds based on environmental criteria such as ambient temprature and the prescribed rate of application. These details are explicitly outlined in their technical data sheets. The bidder shall strictly conform to all such manufacturer criteria to achieve the optimum specified results.(c) Care shall be taken to fill gap/ cracks with 0.6 mm to 2.36 mm size coarse sand with mineral filler as per manufacturers instructions and quoated rate is deemed to included for repair of gap / cracks(d) A performance gurantee certificate for two years shall be submitted by the contractor to the GE on completion of the work specified.(e)No price adjustment shall be applicable if excess/ wastage quantity of bitumen emulsion than that mentioned above is used depending upon the surface to be treated.(f)Removel of dust/ FOD occured during shall be done as directed. (g)Majority of the works to be carried out during night time, bidder should arrange proper illumination for execution of the work |
| 3 | Removel of conflict paint , markings on Apron & runway surface using water blasting cum vacuuming system with suitable operating pressure so that total paint removed from runway both (rigid & flexible) surfaces without damaging the existing surface using suitable machinary all as specified and as directed by Engr-in-Charge. |
| 4 | Note: (a) The surface of both concrete / bitumen (rigid/ flexible ) shall not get any kind of damage during the process of paint removal nor to any adjoining areas, joint filling etc. Damages made if any, shall be made good by the contractor without any extra cost complete all as specified and as directed by Engr-in-Charge.(b) Work shall be carried out in phase manner as per availability of runways for maintanance.(c) Total paint should be removed and debris/ water acuumed simultaneously leaving no FOD so that the eunway is available for operation(d) The machinary used shall be self-propelled, semi-trailer type system incorporating high pressure incorporating a high pressure water pump with a minimum water tank capacity of 22,700 liters, configured with an oscillation high pressure water spray bar. The operating pressure range shall be 350 kg/ cm2 and 700 kg/ cm2 strictly as per Para 8.3.1 of ICAO DOC 9137 Part 2. The technical specification of runway friction tester / Skidometer / Surface friction tester vehicle shall conform to para 5.7, 5.8 and 5.9 of DOC 9137 part 2 respectively |
| 5 | (e) Pre Execution of Trial patch : Prior to full scale deployment of the machinery on the main runway, a trial patch shall be executed . This trial will test the operational efficiency of the equipment, verify that no structural damage occures to the pavement and allow for fine tuning/ modulation of operating pressure based on actual site observations. (f)In any emergency condition the machine should exit from runway in less than two minutes without leaving any FOD.(g)Majority of the works to be carried out during night time, bidder should arrange proper illumination for execution of the work |
| 6 | Removal of Moss/ Algae deposits on Apron and Runway surface using water blasting cum vacuuming system with suitable operating pressure using suitable machinary all as specified and directed by Engr-in-Charge |
| 7 | Note: (a) The surface of both concrete / bitumen (rigid/ flexible ) shall not get any kind of damage during the process of moss/ algae removal nor to any adjoining areas, joint filling etc. Damages made if any, shall be made good by the contractor without any extra cost complete all as specified and as directed by Engr-in-Charge.(b) Work shall be carried out in phase manner as per availability of runways for maintanance.(c) The moss/ Algae should be removed and debris/ water acuumed simultaneously leaving no FOD so that the eunway is available for operation immediately(d) The machinary used shall be self-propelled, semi-trailer type system incorporating high pressure incorporating a high pressure water pump with a minimum water tank capacity of 22,700 liters, configured with an oscillation high pressure water spray bar. The operating pressure range shall be 350 kg/ cm2 and 700 kg/ cm2 strictly as per Para 8.3.1 of ICAO DOC 9137 Part 2. The technical specification of runway friction tester / Skidometer / Surface friction tester vehicle shall conform to para 5.7, 5.8 and 5.9 of DOC 9137 part 2 respectively |
| 8 | (e) Pre Execution of Trial patch : Prior to full scale deployment of the machinery on the main runway, a trial patch shall be executed . This trial will test the operational efficiency of the equipment, verify that no structural damage occures to the pavement and allow for fine tuning/ modulation of operating pressure based on actual site observations. (f)In any emergency condition the machine should exit from runway in less than two minutes without leaving any FOD.(g) Majority of works to be carried out during night time bidder should arrange proper illumination for execution of the work(h) Rate of application of high pressure water between 350 to 750 kg/ cm(j) The work shall be commenced within 45 days of request by user and shall be completed within 60 days of intimation. Incase of failure to finish the work within the stipulated time frame monetary penalty will be imposed upon the Contractor/ firm @ 1% of quoted amount againist item No. 3 upto a maximum of 10% of quoted amount againist item No. 3 herein before for per week of delay beyond 60 days of intimation Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 04, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 18, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 12 daysAug 20, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 14 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender