Tender For Repair /Replacement Of Civil Works To Elevated Security Posts Including Allied Buildings, Afstc Area At 54 Asp Under Ge (Af) Gurgaon No 1
Tender Value
35 Lakhs
Estimated cost
Bid Submission
01 Sep 2026
1 days left
EMD
70000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Gurgaon → Haryana
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair /Replacement Of Civil Works To Elevated Security Posts Including Allied Buildings, Afstc Area At 54 Asp Under Ge (Af) Gurgaon No 1
Corrigendum
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 25-Aug-2026 | Bid Auto Extn Corrigendum | Bid Auto Extn Corrigendum | 01-Sep-2026 |
BOQ
| Sl. No. | Item Description |
| 1 | Schedule-A |
| 2 | Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises completed all as specified and as directed by Engr-in-Charge. |
| 3 | Demolition of cement concrete of any description as in ground floor and paving exc 15 cm thickness(below or above ground level) all as directed by Engr in charge |
| 4 | M&L for pre cast Kerb stone with plain fair faces 300x150x300 mm depth of PCC 1:1 ½ :3 of shape as approved incl all excavation, embedding in ground and removing surplus spoil upto 50 Mtr distance completed all as specified and as directed by Engr-in-Charge. |
| 5 | M&L for providing 100mm thick cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base of floor complete all as specified and directed by Engr-in-Charge. |
| 6 | M&L for 60mm thick Machine pressed pre casted pressed cement concrete inter locking paver blocks glazed coloured up to 6mm on the top in any shape and size,with gray cement and no pigment, strength not less than M-35 completed all as specified and as directed by Engr-in-Charge. |
| 7 | M&L for providing 75mm thick cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base of floor complete all as specified and directed by Engr-in-Charge. |
| 8 | M&L Chequered cement concrete tiles 300x300x20mm thick, set jointed and pointed in near cement slurry in floors with white cement and pigments in any colour machine preassed glazed , over cement screed bed 20mm thick cement motor 1:4 all as specified and as directed by Engr-in-charge. |
| 9 | M&L machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement to match the shade of the slab including rubbing and polishing, including 20mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and as dierected. |
| 10 | M&L machine cut kota stone slab flooring 20-25mm thick in riser of steps,skirting,dado and pillar laid over 10 mm thick plastering in CM 1:4 set and jointed with grey cement to match the shade of the slab including rubbing and polishing completed all as specified and as directed by Engr-in-Charge. |
| 11 | M & L Glazed ceramic tiles in vertical surface 350x 250x 7mm/ 450X 350X 7mm thick over 10 mm thick plastering in CM 1:4, set and jointed in neat cement slurry and pointed in coloured cement to match completed all as specified and as directed by Engr-in-Charge. |
| 12 | S&F Non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, set and jointed in neat cement slurry and pointed in coloured cement as in floor over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and as dierected. |
| 13 | Dismantling of brick work built in cement mortar including all quions, arches, pillars, etc.completed all as specified and as directed by Engr-in-Charge. |
| 14 | M&L for Brick work with sub class B bricks straight or curved on plan exc 6 mtr mean radius built in CM 1:6 completed all as specified and as directed by Engr-in-Charge. |
| 15 | Taking down cement plaster, any description on brick walls or on concrete surfaces including racking out Joints, hacking for Key, scrubbing down with Water, etc., and removing same from the Site(s), complete all as specified and directed by Engr-in-Charge. |
| 16 | M&L for for rendering 15mm thick in CM (1:4) on brick work or concrete surfaces on fair face of brick work, finished fair & even w/o using extra cement in patches with water proofing compound by 3% weight of cement all as specified and directed by Engr-in-Charge. (Note:- Rate of water proofing compund to be used shall be deemed included under this item.) |
| 17 | M&L for rendering 10 mm thick in cement motar 1:6 on brick work or concrete surfaces other than fair face of brick work, finished fair & even without using extra cement all as specified and directed by Engr-in-Charge. |
| 18 | M&L for rendering 5 mm thick in cement motar 1:3 on ceiling on concrete surfaces, finished fair & even without using extra cement complete all as specified and directed by Engr-in-Charge. |
| 19 | Material & Labour for applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and as directed |
| 20 | M&L Preparing New Plastered Surfaces of WALLS and applying TWO COATS of DISTEMPER OIL EMULSION (OIL BOUND WASHABLE DISTEMPER) over a Coat of CHALK WHITING, complete all as specified and as directed. by Engineer-in-Charge. |
| 21 | M&L Preparation of new plaster surfaces of ceiling, and applying two coat of white wash on ceiling all as directed by Engr-in-Charge. |
| 22 | M&L preparation old treated surface by complete removal of existing treatment of wall and applying two coat of cement base pant over a coat of primer complete all as specified and as directed. |
| 23 | M&L preparing old distempered surfaces of wall by complete removal of existing treatment and applying two coat of oil emulsion distemper over a coat of Birla / JK wall putty 3mm thick complete all as specified and as directed. |
| 24 | M&L preparing old distempered surfaces of ceiling by complete removal of existing treatment and applying two coat of white wash complete all as specified and as directed. |
| 25 | M & L preparation of old painted surfaces of steel and iron work of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed. |
| 26 | M&L for preparation of old painted wooden surfaces over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed. |
| 27 | Dismantling mild steel work of any description not otherwise provided completed all as specified and as directed by Engr-in-Charge |
| 28 | Mild steel plates, plain or chequered, 5mm thick or over in thickness in available sizes Fe 410 W (Gde-E-250) quality-A with riveted bolt or welded etc as in duct cover & similar work completed all as specified and directed by Engr-in-Charge |
| 29 | M&L for structural steel rolled section as tubular sections as in vertical steel columns with flange plates, caps, bases, base plates, splices angle brackets, cleats, holding down bolts and nuts and other section complete of Fe 410 W E-250 grade including all welding etc, complete all as specified and directed by Engr-in-Charge. |
| 30 | S&F for MS angle iron as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc flat iron fillets (for securing with mesh etc including all necessary drilling bolting or riveting etc and similar work confirming to Fe-290 (Gde-E-165 quality-B. Note:-Posts/struts of angle iron made to shape shall be welded to existing angle iron bracket of security wall, contractor shall make his own arrangement for welding for boundary wall by using gen sets or any alternative arrangement. |
| 31 | M&L for Preparation of new steel surface exc 10 cm width/girth one coat red oxide primer and two coat synthetic enamal paint completed all as specified and as directed by Engr-in-Charge. |
| 32 | S&F in repair Galvanized 2 strand Steel Barbed wire 2.24mm dia barbed with dia barbs at 75 mm spacing and straining and fixing to any type of stsnderd rails, straining bolts,including securing or tying at crossings with and provisuion of galvanised mild steel pins, etc including taking down of existing barbed wire as directed (each line wire to be measured) complete all as specified and directed by Engr-in- Charge |
| 33 | M&L for Dismantling of plain or corrugated steel sheeting / AC sheeting any gauge thickness inculing nanital or similar pattern roor coverings all as specified and directed by Engr-in-Charge. |
| 34 | M&L for Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified |
| 35 | S&F 2 mm thick fibre glass reinforced translucent corrugated/ plain sheeting with two corrugations side lap fixed with L type or J-type or cranked hook botls and washer in roof, wall and similar work etc all as specified and directed by Engr-in-Charge. Make: Everest/ MG Polyplast or equivalent make approved in MES in any Command. |
| 36 | Hacking out old broken glass exc 1.5 sqm (any thickness, size, quality or description) from wooden/steel/aluminium frame glazed with putty or fixed with wooden /almn beads etc.completed all as specified and as directed by Engr-in-Charge. |
| 37 | S&F 4 mm thick sheet glass,ordinary quality,in squares n exc 0.5 sq m each pane fixed to aluminium frame with rubber gasket or fixed with glass putty as required etc completed all as specified and as directed by Engr-in-Charge. |
| 38 | Taking down Chowkhats or frames n exc 1.5 sqm each without taking of shutter from the frame all as specifed and directed by Engr-in-Charge. |
| 39 | Taking down shutter of any discription n.exc 1 Sqm each complete all as specified and directed by Engr-in-Charge. |
| 40 | Taking down shutter of any discription exc 1 Sqm but n exc 2 Sqm each complete all as specified and directed by Engr-in-Charge. |
| 41 | S&F factory made 30mm thick solid core Flush door shutter with block board with BWP plywood on both side all as specified directed by Engr in Charge. |
| 42 | M&L second class Hardwood 35 mm thickness, glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beds for securing glass, etc.; sizes of members of shutters as specified by Engr-in-Charge. |
| 43 | M&L second class hardwood 30mm thickness plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers; supplied and fitted to chowkats all as specified and directed by Engr-in-Charge |
| 44 | S&F stainless steel wire cloth with 8% nickle 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staple complete all as specified and directed by Engr-in-Charge. |
| 45 | S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel heaving a PVC sheet strip of 20mm width suck inside with solvent cement for stiles and wood grain printed PVC Sheet used 5mm thick x 15mm wide PVC sheet beading used inside stiles and rails and decorative PVC beaading of 10mm x 10mm used instead of exposed portion of PVC sheet beading for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; supplying & fixing in the frame at site as per specification & drawing. |
| 46 | Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawing. |
| 47 | M&L for preparation of new wooden surfaces of any description not otherwise described, over 10 cm width or girth and applying two coat of synthetic enamel paint over one coat of pink wood primer all as specified and directed by Engineer-in-Charge. |
| 48 | S&F aluminium anodised 150 mm handle complete all as specified and directed. |
| 49 | S&F aluminium anodised 100 mm handle complete all as specified and directed. |
| 50 | S&F aluminium anodised 150 mm long tower bolt complete all as specified and directed. |
| 51 | S&F aluminium anodised 100 mm long tower bolt complete all as specified and directed. |
| 52 | S&F 100mm long butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 |
| 53 | S&F 75mm long butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 |
| 54 | S&F for Aluminium alloy, anodised sliding door bolt with hasp, staple(bolt type) and fixing clips of sheet, cast or extruded section of length of bolt in 200mm complete all as specified and directed. |
| 55 | Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed. |
| 56 | S&F 8 to 10mm thick densified reqular edged eco friendly light weight calcium silicate false ceiling tiles size 600x600mm including main 'T' runner of size 24x38mm made from 0.33 mm sheet hot deep galvanized steel section making good existing frame without disterbing the other false ceiling with all as directed by Engr-in-Charge. |
| 57 | M&L for Providing & fixing false ceiling at all heights with Semi perforated 12mm thick micro tegular edged GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595 x 595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per 8225:1987, Noncombustible as per BS 476 (part 4)-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main- T runners of size 15 x 32 mm of length 3000mm,cross-T of size 15x 32mm of length 1200mm and secondary intermediate cross-T of size 15 x 32 mm of length 600mm to form grid module of size 600x 600mm, suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1000mm length and L-shape level adjuster of size 85x25x2mm.Galvanised iron perimeter wall angle of size 24x 24x0.40mm of length 3000 mm to be fixed on periphery wall I partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge. |
| 58 | Taking down existing bitumen felt roof treatment including padding/ cement mortar bedding and cleaning the surface and dremoval outside the MOD land, complete all as specified and directed Note- Taking down earthng strips from roof and re-fixing on the same position after APP laying is deemed to be inclusive of rate quoted by the contractor |
| 59 | M&L for Cutting out cracks 'V' section on existing roofs or terrace cleaning out and filling solidly with a hot mixture bitumen and clean dry sand 1:1 by weight complete all as specified and directed by Engr-in-Charge. |
| 60 | M&L 25 mm thick PCC 1:2:4, type B0 (using 12.5mm graded aggregate ) as in padding of floors/ roof surface finished even and smoot surface complete all as specified and as directed by Engr-in-Charge. |
| 61 | M & L rendering 10 mm thick fare faces of brick work or concrete surfaces in CM (1:4) mixed with WPC as per manufacturer’s instructions, @ 0.5 % by weight of cement on concrete surface finished even and smooth without using extra cement complete all as specified and directed. Note : WPC shall be measured and paid separately. |
| 62 | M&L water proofing treatment on roof and vertical surface consisting as under:- (a) Applying evenly a coat of bituminous primer conforming to IS-3384:1986 @ 0.30 litre/sqm including preparation of roof surfaces (b) Applying evenly a tack coat of industrial bitumen 85/25 @ 1.2 kg/Sqm on plaster surface all as specified.(c) A layer of 3mm thick APP polymeric membrane of weight not less than 3.60 kg/sqm, reinforced with polyester non-woven fabric (weight not less than 160gm/ sqm), duly sealed at over laps & joints with end laps of the 10cm and side over laps of 7.5cm by flame (by torch application) all as per manufacturer’s instructions, complete all as specified and directed. |
| 63 | Supply only water proofing liquid compound complete all as specified and directed by Engr-in-Charge. |
| 64 | M&L for applying one coat Bitumen water proofing aluminium heat resistance paint on the roof as per manufacture instructions complete all as specified and directed by Engr-in-Charge. |
| 65 | Note :- The amount of Rs 48025.00/- against Schedule of Credit on Srl Page 141 shall be deducted from the total amount quoted against Sch 'A' Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 25, 2026
11:30 IST
Tender Published
Tender notice published.
Completed
Sep 01, 2026
18:00 IST
Corrigendum-1 Issued
Clarifications on tender conditions and amendments issued.
Upcoming · 1 daySep 01, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 1 daySep 03, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 3 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender