Tender For Renovation Of Suchna Kendra , Kota (Auditorium,Entrance Hall And Outer Development)
Tender Value
1.42 Crore
Estimated cost
Bid Submission
10 Aug 2026
1 days left
EMD
2.85 Lakhs
Bank guarantee accepted
Document Fee
3500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Kota → Rajasthan
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Renovation Of Suchna Kendra , Kota (Auditorium,Entrance Hall And Outer Development)
BOQ
| Sl. No. | Item Description |
| 1 | Providing and Fixing of Armstrong Acoustical Wall Panel with square edges made of fibre glass substrate 25mm thick, wrapped on the front side with an acoustically transparent fabric as per the approved shade (Husk, Copper, Sangria, Sesame, Coffee, Charcoal, Titanium, Flame, Peanut and Shell). The panel shall be classified for Fire Class A, as per ASTM E-84. The Acoustical Wall Panel shall be of sizes 600x300mm (Nominal), 600x600mm (Nominal), 600x1200mm (Nominal) and 600x1800mm (Nominal) and shall achieve an NRC of 0.85 (Average value of Absorption Co-efficient readings taken at 250 Hz, 500 Hz, 1000 Hz and 2000 Hz) with 50mm airgap as per ASTM C423 to be fixed to wall on a framework of aluminium and using Wall panel Impalers (supplied by the manufacturer) or by using construction adhesives (as per the instructions laid down by the manufacturer). The fibre glass supstrate shall have a recycle content of 85%. |
| 2 | An appropriate vapour barrier (by others) shall be applied/installed on the vertical surface before the installation to properly seal against entry of any moisture. Vapour barrier (by others) shall be installed as per Manufacturer's recommendation. Install aluminium grid (provided by others) of section 100x50mm or as approved by the Architect on the solid wall/partition to provide level and plumb surface. The Impalers shall be fixed to the battens using self-tapping screws, 3 nos. in case of 600x300. 600x600mm, and 4 nos. in case of 600x1200mm and 600 x 1800mm Silica based construction adhesive (by others) to be dabbed on to the projecting elements (spikes) of the Impalers. Wall Panels shall be pierced through the spikes of the Impalers ensuring the line and level of the panels are maintained. |
| 3 | GRID CEILING Armstrong make 600×600×15 ceiling with G.I. Channels (gauge 24mm) support @ GRID OF 600×600 with all necessary light fitting and necessary cutouts as required (ARMSTRONG-PRIMA BOARD FINE FISSURED or EQUVALENT-rating has to be same) |
| 4 | Providing and fixing Mandana Cobble Stone flooring work dressed stone 100mm thick in hound finished with pattern as per approved design over 25-50mm thick base in CM 1:6 incl. pointing with cement sand mortar 1:2 (1 Cement:2 sand)match the shade of stone with joint complete in all respect as per direction of engineer-in-charge & Architect with all lead & lift. |
| 5 | Supply and installation of Centre Table Overall Size 1215W X 605D X 450H mm, Table Top Made Of Veneer & Melamine polish, Inner material used in Table top is 18mm thickness commercial block board & prime quality veneer pasted on it with Melamine polish, Table Top Size 1215W X 605D X 18mm Thickness, Teak colour Veneer pasted on table top, Legs made up of solid teak wood material of size 60W X 60Dmm, Under structure Top Supported Panel Made Of Prime Quality Solid teak Wood material of size 60x20mm, complete structure are in Melamine polish, commercial Board Use Prime Quality With ISI Marked , All Wooden Panels Cleaning Corner Knitted Finish , Wooden Panel Joint Leg To Leg Supported To Top . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design. |
| 6 | Supply and installation of Three seater Sofa , Overall Size 1920W X 750D X 750H , Sofa structure made good quality solid wood of size 38x25mm Uphostered With Leatherite & HD Foam used in seat & Back density 32 KG/m3, Sofa base Supported on metal legs , Sofa Back Height from ground is 750mm , The rounded Armrests Provided with Sleek And Stylish Look, complete Understructure Made of Solid Wood Structures With Heavy duty zig zag Spring For Maximum Comfort, Seat Height From Ground 460mm , 100mm High Legs . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design. |
| 7 | Providing and fixing 12MM toughened glass and staking with spider SS fittings & Weather proofing of glass panels using weather proof silicon (Dow Corny 789) complete in all respect as per drawings attached (Drg-7), as per direction of Engineer-in-charge and Architect with all lead and lift |
| 8 | Providing and fixing aluminum work for doors ,windows, ventilators and partition with extruded built up standard tubular / appropriate Z sections and other sections of approved make conforming to IS :733 and IS :1285, fixed with rawl plugs and screws or with fixing clips ,or with expansion hold fasteners including necessary filling up of gap. at junctions , at top ,bottom and sides with required PVC/neoprene felt etc. Aluminium section shall be smooth ,rust free, straight ,mitered and jointed mechanically wherever required including cleat angle Aluminium snap beading for glazing /paneling , C.P. brass/ stainless steel screws Al. Tower bolt & Al. handle & Al. Aldrop etc.,all complete as per architectural drawings and the directions of Engineer- in – charge .(Glazing and paneling to be paid for separately). |
| 9 | For shutters builtup standard tubular sections of openable doors ,windows & ventilators including providing & fixing hinges / rollers etc. and making provision for fixing of fittings wherever required (lockes shall be paid for separately). |
| 10 | Powder coating aluminum ( minimum thickness of powder coating 50 micron) |
| 11 | Providing and fixing glazing in aluminium door, window ,ventilator shutters and partitions etc. with PVS / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge.(Cost of aluminium snapbeading shall be paid in basic item.) |
| 12 | With float glass panes of 5.0 mm thickness ( weight not less than 13.50 kg/sqm) |
| 13 | S&f fixed wire gauge of stainless steel of 14 mesh x 24 gauge to the aluminium window by Aluminium beading 20x3mm with suitable screws not exceeding 150mm distance at all heights with all lead and lift with scafolding. |
| 14 | Providing & Fixing Aluminium composite panel of indo bond/euro/flexi bond of equivalent made 3mm that with 0.5mm thick skin& PVDF coated of approved shads for toilet door in double layer in Aluminium frame complete in all respect as per sample approved by Engineer in Charges. |
| 15 | Providing and fixing expanded grill made of aluminum as per design and drawing having members section of size 7.5mm x 6.0mm andopening of size 102mm x 99mm to aluminum window/vent with required screws, Y and H aluminium section (as per drawing) at theends and middle joints respectively complete in all respect as per direction of engineer in charge. |
| 16 | Powder coating aluminum ( minimum thickness of powder coating 50 micron) |
| 17 | Filling the gap upto 5 mm depth and 5 mm width in betweenaluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineerin-charge complete. |
| 18 | viding and fixing double action hydraulic floor spring of approved brand and manufacture IS : 6315 marked, for doors including cost of cutting floors as required, embedding infloors and cover plates with brass pivot and single piece M.S. |
| 19 | With stainless steel cover plate |
| 20 | With stainless steel cover plate |
| 21 | Providing and fixing stainless steel railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required)and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 22 | Grade 304 |
| 23 | Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying |
| 24 | after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. |
| 25 | laying second layer of Fiber glass cloth when the first layer is still green . Overlaps of joints of fiber cloth should not be less than 10 cm . |
| 26 | Third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proffing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30cm on |
| 27 | fourth and final layer of brick tiling „with cement mortar or any other approved protective coarse. (which will be paid for separately) For the purpose of measurement the entire treatedsurface will be measured |
| 28 | Providing and Applying ACRYLIC emulsion polymer waterproofing chemical coating, on over roof on over roof slabs/terrace/balconies/parapet wall etc.with following method/specification: Paint the surface with regular paint brush so as to obtain approximately 0.3mm thickness coating. apply the 2nd coat next day at right angles to the 1st coat so that total thickness of the coating should be approximately 0.6mm coverage by using above formulation will be 40 ft2/ litre of chemical. painted surface does not require any external water curing since chemical will hold sufficient water for curing.After the primer coat Apply 2 coats of modified acrylic emulsion polymern water proofing compound having solar heat reduction properties coating @ 0.330 KG/SQM on the surface of the interval of 3-4 hours. Undulation on the surface is repair before the waterproofing work. |
| 29 | Extra for Mirror polishing on terrazzo/Kota stone work where ever required to give high gloss finish complete. |
| 30 | Dismantling tile work in floors and roofs laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 meter lead:For thickness of tiles 10mm to 25mm. |
| 31 | Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish : |
| 32 | 20mm thick. |
| 33 | Painting exterior surface of Wall with 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including prepartion of base with sand papering, primer, putty, etc complete in all respect including scaffolding and safety provision |
| 34 | New Work |
| 35 | Providing and applying white cement based putty over plastered surface to prepare the surface even and smooth complete |
| 36 | New Plastered Surface (three or more coats) |
| 37 | Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade including all scaffolding: |
| 38 | Two or more coats on new work including prepartion of base with primer, putty, lippy etc complete in all respect. |
| 39 | Providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles confirming to code IS : 15622 of size 200mm x 300mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cementmixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster on walls and pillar). |
| 40 | Providing and fixing 1st quality MAT finished ceremic tile size 300x300mm confirming to code IS : 15622 colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tilecomplete (including the cost of cement mortar bed 1:4). |
| 41 | P & F European type white glazed vitreous china 1st quality Double syphonic W.C (IS :2556 Mark) with P or S trap including cutting and making good the wall and floorr |
| 42 | P & F Premium quality Low level Flushing Cistern of 10 litres capacity (IS:2556 mark) of approved make as per Engineer-incharge with complete fittings C.I. brackets duly painted, brass ball cock with ball, (IS:1703 mark) complete including cutting and making good the wall : |
| 43 | P & F WVC Wash basin (Ist quality IS:2556 Mark) of approved make with C.I. brackets duly painted 1 No. 15 mm C.P. Pillar cock (IS:8934 Mark) & 32 mm C.P. brass waste coupling of approved make, P.V.C Waste pipe with PVC nut 32 mm complete including cutting & making good the wall : |
| 44 | size 550 mm x 400 mm |
| 45 | P & F Inlet Connection (Angle Valves) Superior quality, of approved make, for Wash basin, Gyser etc. |
| 46 | C.P. Inlet connection 15mm.Brass (IS : 8931 marked) |
| 47 | P & F PVC Storage Tank ISI Marked (IS : 12701) indicating the BIS license No), of approved make with cover, 25mm dia 1M long G.I. over-flow pipe & 25 Cm. long wash out pipe with plug & socket, including making connection etc., complete of approved design: |
| 48 | 500 (-do-) |
| 49 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes (IS 15778 : 2007 code) having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1 metre spacing. This includes jointing of pipes & fittings with onestep CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. (Internal work Exposed on wall) |
| 50 | 15 mm nominal size |
| 51 | 25 mm nominal size |
| 52 | P & F Bib Cock (IS : 8931 Mark), Superior quality of approved make: |
| 53 | C.P. Brass bib cock,15mm nominal bore. |
| 54 | P & F Premiumquality water closet Seat Covers with brass hinges complete Solid PVC (ISI marked) grade-I White for EWC. |
| 55 | P & F Jet spray for water closet with C.P. Copper Tube flange of approved make. |
| 56 | P & F Looking Mirrors with P.V.C. frame of approved make as per direction of Engineer-in-charge |
| 57 | Oval shape 450x350 mm |
| 58 | P&F rigid PVC Pipe (IS:4985 mark) class II/ (4 Kg. /Cm2 .) approved quality /make including joining the pipe with solvent cement rubber ring and lubricant. |
| 59 | 110 mm dia |
| 60 | P&F rigid PVC pipe fittings (IS: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant: |
| 61 | Coupler (socket) |
| 62 | Bend 87 .5 |
| 63 | Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. All kinds of soils |
| 64 | Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. |
| 65 | M10 grade Nominal Mix 1: 3: 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size). |
| 66 | Providing and laying cement concrete including curing, compaction etc. complete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, levelling course etc up to floor fivelevel excluding the cost of centering and shuttering. |
| 67 | M20 grade Nominal Mix1: 1.5: 3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size). |
| 68 | Centering and Shuttering with plywood or steel sheets including strutting, propping bracing both ways and removal of formwork for foundation , footings, strap beam, raft , basesof columns etc. |
| 69 | Centering & shuttering with plywood or steel sheets includingstrutting, propping bracing both ways with steel props andremoval of formwork for upto floor five level for : |
| 70 | Columns, pillars, posts and struts etc. |
| 71 | Suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates, anchor blocks, |
| 72 | Providing and fabricating reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up tofloor five level. ('Original producers' who manufacture billet directly from iron ores and roll the bilets to produce steel conforming toIS:1786) |
| 73 | Thermo-mechanically Treated bars (Conforming of relevent IScode) |
| 74 | Providing & fixing Brown Kota/ Mandana / Dholpur/ slate stone in cladding / Flooring Structural base with white cement & Tinex chemical & SS Clamp and Fasteners (of approved brand) laid and jointed with white cement slurry mixed with pigment to match the shade of the slab as per drawing attached complete in all respect as per direction of Engineer- In- Charge & Architect with all lead & lift. The Stone measurement will be done of outer most dimension. Thickness of stone 25-30mm. |
| 75 | P/F Ornamental pink Bansi Paharpur stone chhatri (Total height = 0.60+1.50+0.10+0.05+0.10+0.10+0.05+0.75+0.30) and 1.20 m x 1.20 m size with following specification with carving work (All measurement are in metres) cladding- 4 x 1.00 x 0.525 x 0.04 thick, cladding pillars - 4 x 0.10 x 0.10 x 0.52 , Galta - 4 x 0.15 x 0.075 size, Dhasa - 4x0.30x0.075 size main pillars - 4x0.15x0.15x1.50, Aech - 4x0.525 height and 0.05 thick , barsoth- 4x0.15x0.10 size chajj - 4x0.05 thick with 0.25 projection dabstone - 1.20x1.20x0.10 step cladding above dabstone - 4x0.04 thick x 0.10 height (with cc 1:2:4, 1.00x1.00x0.10), Gola stone- 1.20x1.20x0.05, Gumbad - 1x.75 dia. x 0.60 height, kalash- 1x0.30 height and .125 dia at base complete as per approved design and direction of engineer in charge |
| 76 | Single piece of stone element with carving work in Bansi Paharpur stone includes stone pillar, stone base, todies and thabi etc carving work as per direction of engineer in charge |
| 77 | Providing and fixing steel gate, grating , and grills made ofangles, tees, square bars, flats,or black pipe with holdfast andfittings complete as per design and drawing including cuttingwelding and fabrication with priming coat of red oxide |
| 78 | Extra if square,rectangular hollow tubelar sections are used orgrill made by flats only |
| 79 | Random Rubble stone masonry with hard stone in superstructure above plinth level and upto five level above 30cm. thick walls in : |
| 80 | Cement Mortar 1:6 ( 1-Cement : 6-Sand). |
| 81 | Painting with synthetic enamel paint of approved brand andmanufacture to give an even shade : |
| 82 | Two or more coats on new work |
| 83 | Providing and fixing Granite stone slab mirror polished and machine edge cut in walls, pillars, steps, Shelves, Sills Counters, Floors etc. laid on 12mm (Av.) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) jointing with whitecement mortar 1:2 (1white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete. |
| 84 | South (Red) |
| 85 | Brick work with F.P.S. bricks of class designation 75 insuperstructure above plinth level upto floor V level in allshapes and sizes in : |
| 86 | Cement mortar 1 : 6 (1 cement : 6 coarse sand) |
| 87 | Colour washing of all shades to give an even shade includingall scaffolding : |
| 88 | Old work (one or more coats) with lime including scrappingsurface. |
| 89 | Extra for providing edge moulding to 15-18mm thick marble/Granite/Kota stone counters, Vanities etc. including machinepolishing to edge to give high gloss finish etc. complete as perdesign approved by Engineer-in-Charge. |
| 90 | Full Edge moulding Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 05, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 10, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 1 dayAug 11, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 2 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender