Tender For Construction Of Lis Of Village Bela Salehra, Kundlu, Thoda, Baroona, Khillian Pahari Bas, Jagatpur And Joghon Etc. In Tehsil Nalagarh, District Solan Hp (Sub Head:- Construction Of Pump House Cum Attendant Quarter, Provision Of Electrical
Tender Value
1.39 Crore
Estimated cost
Bid Submission
14 Aug 2026
4 days left
EMD
2.14 Lakhs
Bank guarantee accepted
Document Fee
5000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Solan → Himachal Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of Lis Of Village Bela Salehra, Kundlu, Thoda, Baroona, Khillian Pahari Bas, Jagatpur And Joghon Etc. In Tehsil Nalagarh, District Solan Hp (Sub Head:- Construction Of Pump House Cum Attendant Quarter, Provision Of Electrical Fitting In Pump Houses, Construction Of Main Delivery Tanks, Construction Of Field Out Lets, Laying Jointing And Testing Of Gms Pipe Conforming To Bis 1239 In Rising Main, Laying Jointing And Testing Of Hdpe Pipe Conforming To Is 4984-2016 In Distribution System, Supply Erection Of Submersible And Centrifugal Pumping Machinery Alongwith Its All Allied Accessories, Construction Of Sumpwell, Construction Of Wire Crates For Diversion Bandh And Feeder Channel, Construction Of Boundary Walls Around The Pump Houses, Providing Installing Electromagnetic Flow Meters) Under Nabard, Job No. 2.
BOQ
| Sl. No. | Item Description |
| 1 | Excavation work by mechanical means ( Hydraulic excavator)/ menual means in foundation trenches upto all depths in all classification of earth work such as pick work, jumper work, saturated soil including bailing of pumping out water, blasting soft/ hard rock where blasting is prohibited. In all lifts including trimming and dressing of sides, levelling of beds to correct grade i/c shoring, strutting, planking timbering and dewatering wherever required, stacking the usable and un-useable material / soil separately and after laying, jointing of pipes returning the useable soil in trenches in trenches in 15 cm (fifteen centimeters) layers including consolidating of each of each deposited layer by ramming and watering and disposing of all surplus excavated soil un useable materials as directed within all leads & lifts including restoration of un-metalled surfaces to its original condition and including cost of diverson for traffic night signals, fixing caution boards, crossing over trenches for excess to houses, fencing etc.complete in all respect with in all leads & lifts as per the direction of the Engineer-in-charge. |
| 2 | Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, in all depth, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within all leads and lifts in all kinds of soil complete in all respect and as per the direction of and to the entire satisfaction of the Engineer in charge.( Pipe cable etc. exceeding 80mm dia but not exceeding 300 mm dia) |
| 3 | Providing and laying cement concrete 1:5:10 ( I cement : 5 sand : 10 graded stone aggregate 40 mm nominal size)and curing complete excluding the cost of form work in foundation and plinth including carriage of material in all leads & lifts and as per the direction of the Engineer-in-charge. . |
| 4 | Providing and laying cement concrete 1:4:8 ( I cement : 4 sand : 8 graded stone aggregate 40mm nominal size)and curing complete excluding the cost of form work in foundation and plinth including carriage of material in all leads & lifts complete in all respect and as per the direction of Engineer in charge. |
| 5 | 1st class Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:- Cement mortar 1:6 (1 cement : 6 coarse sand) complete in all respect and as per the direction of Engineer in charge . |
| 6 | 2nd class Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:- Cement mortar 1:4 (1 cement : 4 coarse sand) complete in all respect and as per the direction of Engineer in charge. |
| 7 | Frist class Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:6 (1 cement : 6 coarse sand)complete in all respect and as per the direction of Engineer in charge. |
| 8 | Providing Centering and shuttering including strutting, propping etc. and removal of form for all heights Suspended floors, roofs, landings, balconies and access platform. with waterproof ply 12 mm thick and string courses and like complete in all respect and as per the direction of Engineer in charge. |
| 9 | Vertical surfaces such as walls (any thickness), partitions and the like including attached pillasters, buttress,plinthand string courses and the like in all leads and lifts. |
| 10 | Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. (Note :- Cement content considered in this item is @ 330 kg/ cum. All works above plinth level upto floor V level).complete in all respect and as per the direction of Engineer in charge. |
| 11 | Providing and laying in position machine batched and machine mixed design mix M-30 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. (Note :- Cement content considered in this item is @ 340 kg/ cum. Access /less cementused as per design mix is payble/recoverable seprately ( all works upto plinth level to V level ).complete in all respect and as per the direction of Engineer in charge. |
| 12 | Providing Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500 D or more. including carriage of material in all leads & lifts complete in all respect and as per the direction of Engineer in charge. |
| 13 | Steel work welded in built up section truses and framed work including cutting hoisting,fixing in position and applying a priming coat or red lead painting in grating framed guard bars, ladders,railing,bracket and similar works including carriage of material in all leads & lifts complete in all respect and as per the direction of Engineer in charge. |
| 14 | 15 mm cement plaster in single coat on rough side of brick masonry for interior plastering upto floor two level including arrises, internal rounded angle, chamfers and or rounded angles not exceeding 80 mm in girth and finished even and smooth with cement mortor 1:5 ( 1 cement : 5 sand ) including all leads and lifts and as per the direction of the Enginner-in-Charge. |
| 15 | 15 mm cement plaster in single coat on rough side of brick masonry for interior plastering upto floor two level including arrises, internal rounded angle, chamfers and or rounded angles not exceeding 80 mm in girth and finished even and smooth with cement mortor 1:3 ( 1 cement : 3 sand ) including all leads and lifts and as per the direction of the Enginner-in-Charge. |
| 16 | P/ F pressed steel door frames manufactured from commercial MS sheets of 1.25mm thickness including hinges, jump lock jamp. Bead and if required angle threshold of MS angle 50 x 25 mm or base tie of 1.25mm pressed MS welded or rigidly fixed together by mechanical means, adjustable lugs with split and tails to each jamp i/c steel butt hinges 2.5mm thick with guards, lock strike plate and shock as specified and applying a coat of steel primer after pretreatment or surface as directed by Engineer-in-charge. |
| 17 | Profile---\\"B\\" |
| 18 | Profile---\\"C\\" |
| 19 | Providing and fixing 1mm thick M.S.sheet door with frame of 40mmx40mmx6mm angle iron 3.15mm M.S. gusset plate at the junctions and corners including all necessary fittings, complete including applying a priming coat of red lead paint.using flat 30mm x6mm for diagonal braces and control cross/pieces.complete in all respect and as per the direction of Engineer in charge. |
| 20 | Filling in plinth with sand under floors including watering ramming consolidating and dressing complete. in all leads and lifts as per the direction of the Enginner-in-Charge. |
| 21 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate including carriage of materials with in all leads and lifts.and as per direction of the Engineer-in-Charge. |
| 22 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. complete in all respect.including entire carriage of material and as per direction of the Engineer-in-Charge. |
| 23 | Providing and applying Birla white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.and as per direction of the Engineer-in-Charge. |
| 24 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer and as per direction of the Engineer-in-Charge. |
| 25 | Finishing with Deluxe/ Apex Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture and as per direction of the Engineer-in-Charge. |
| 26 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.complete in all respect. |
| 27 | Painting two coats(excluding priming coat) on new steel work based surfaces,with ready mixed paint,brushing to give an even shade including cleaning of all dirt,dust and other foreign matter,sand papering and stopping,with paint other than white..complete in all respect. |
| 28 | Providing and fixing M.S. fan clamp type I or II of 16 mm dia M.S. bar, bent to shape with hooked ends in R.C.C. slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete. |
| 29 | Providing and fixing M.S. grills of required pettern in windows frames of windows etc. with M. S. Flats Square or round bars with round headed bolts and nuts or by screws. (Plain grill) Fixed to openings /wooden frames with rawl plugs screws etc.complete in all respect. |
| 30 | Providing & fixing M.S. gate of angle iron and flat 6 mm thick with frame I/c locking arrangment andplacing in position complete i/c carriage of materials with in all leads and lifts. |
| 31 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked of suitable capacity 500 liters , with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. complete in all respect. ( 1No. tank of 500 liters capacity) |
| 32 | P/F vitreous china wash down water closet squatting pan (Indian Type WC pan) size 580 mm (Earth work, bed concrete, foot rest and tap should be measured and paid for seprately (Orissa Pattern) complete in all respect and entire satisfaction of Engineer in charge. |
| 33 | P/F high pressure PVC spigot and soaket, waste and ventilating pipes ISI marked i/c fixing with approved adhesive etc. complete 110 mm dia complete in all respect and entire satisfaction of Engineer in charge |
| 34 | Providing and fixing PVC trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors 100 mm inlet and 100 mm outlet complete in all respect and entire satisfaction of Engineer in charge |
| 35 | P/F brass bib tap (Superior or heavy type) of 15 mm dia complete in all respect complete in all respect and entire satisfaction of Engineer in charge. |
| 36 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work -Exposed on wall |
| 37 | Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS: 15622(thickness to be specified by the manufacturer) of approved make in all colours, shades except burgundy, bottle green,black of any size as approved by Engineer-in- Charge in skirting,riser of steps and dados over 12mm thick bed cement mortor 1:3( 1cement:3 course sand) and jointing with grey slurry @ 3.3 Kg per sqm including pointing in white cement mixed with pigment of matching shade complete in all respect and as per direction of Engineer in Charge. |
| 38 | Providing and fixing ISMB 200X100 in Pump house for chain pully complete in all respect and as per direction of Engineer in Charge. |
| 39 | Laying, jointing, testing and commissioning at site in trenches GMS tube (Medium & Heavy grade) of following dia meters for rising main as under conforming to BIS 1239 part-I or latest wih upto date amendments, capable of withstanding required test pressure as prescribed in BIS code in random length of 5.50 to 6.50 metres including specials, short pieces, bends, reducer, Tee etc. made from parent tube. The joiniting of pipes shall be done with butt welded joints, MS flanges are to be provided in 1% of total joint and remaining 99% joint shall be provided with butt welded joints. The pipe end shall be bevelled suitable for butt welding conforming to IS- 816-1969 or latest wih upto date amendments as applicable to make joint leak proof in two layers at site of work with electrod as per IS 814-2004 or latest wih upto date amendments. The laying of pipes should be conform to BIS code 5822-1994 or latest wih upto date amendments and shall i/c the cost of all operation such as cutting, welding, DP test of butt welding joints , jointing making pipe bevelled for butt welded joints, fabrication of bend, Tee, valve etc. i/c lowering and laying in excavted trenches to ensure required level i/c flushing, cleaning and hydraulic testing complete in all respect and carriage of materials at site in all leads lifts as directed by Enginer-in-charge. Nominal dia Thickness Class |
| 40 | 100 mm 5.40 GMS ( Heavy ) |
| 41 | 100 mm 4.50 GMS ( Medium ) |
| 42 | 125 mm 4.80 GMS (Medium ) |
| 43 | 150 mm 4.80 GMS ( Medium ) |
| 44 | Providing and fixing M.S plate flanges of following dia @ 1% of total joint, conforming to following table as per IS 6392- 1971 (latest upto date amendments) and welding of MS flanges with GMS tube in three layers (two layers on outer face and one layer on inner face) to make joint leakproof with required numbers and size of nut bolts conforming to BS 1364 (latest upto date amendments), The welding of flanges should conform to IS 816-1969 with electrode as per IS 814-1994 ( the cost for laying and jointing of GMS pipe and butt welded joint, to be measured and paid for seprately) The thickness of gaskit ( champion sheet) should not be less than 3 mm thick conforming to IS 2712-1998 or latest upto date amendments complete in all respect and carriage of materials at site as in all leads lifts directed by Enginer-in-charge. Nominal dia flange Table |
| 45 | 100 mm 28 |
| 46 | 100 mm 17 |
| 47 | 100 mm 5 |
| 48 | 125 mm 5 |
| 49 | 150 mm 5 |
| 50 | Laying, jointing and commissioning of HDPE (High Density Polyethylene pipes) of following diameter and class confirming to IS 4984-2016 with fusion welding process including all necessary fittings & bends in all leads and lifts to the entire satisfaction of Engineer-in-charge.(Earth work in trenches to be measured and paid separately) |
| 51 | HDPE pipe 125 mm dia PN 4.0 PE 80/100 |
| 52 | HDPE pipe 140 mm dia PN 4.0 PE 80/100 |
| 53 | HDPE pipe 140 mm dia PN 4.0 PE 80/100 |
| 54 | HDPE pipe 125 mm dia PN 4.0 PE 80/100 |
| 55 | HDPE pipe 125 mm dia PN 4.0 PE 80/100 |
| 56 | Wire crates of G.I. wire filles with boulders with square cut faces against the wire ( wire crate to be measured and paid for seprately) complete in all respect including carriage of materials with in all leads and lifts.and as per direction of the Engineer-in-Charge. |
| 57 | Wire crates made of G.I. wire filled with boulders square cut faces against the wire ( Boulder filling to be measured and paid for seprately) 5 mm thick G.I wire corresponding to SWG-8 10x10cm mesh complete in all respect including carriage of materials with in all leads and lifts.and as per direction of the Engineer-in-Charge. |
| 58 | Providing and fixing magnetic flow meter complete in all respect including carriage of materials with in all leads and lifts.and as per direction of the Engineer-in-Charge. |
| 59 | Pumping Machinery :- SUBMERSIBLE Pump set for Tube well Jagatpur-II (Joghon):- Supply, erection, testing & commissioning of submersible/ mono submersible pump for tube well pumping set of reputed make such as KSB/ BS/Johnston / Clama/ SU/ Kirloskar or any other state/ department approved make conforming to latest relevent BIS code 8034 & IS 9283 for motor. The pump should be fitted with free flow impellers of bronze /suitable alloy as per IS 8034-2002 or latest with up to date ammendments suitable for raw water having greased packed bearings & shaft with wound stator on motor side & with shaft protection sleeve on pump side ensuring better life for shaft conforming to BIS specifications. The pump shall be directly coupled to a siutable submersible energy effecient motor of minimum effeciency level IE-2 of Kirloskar/ NGEF/ Jyoti / Crompton / BHEL/ GEC/ SIEMENS/ ABB/ MATHER & PLATmake conforming to relevent BIS code compatible with pump with up to date ammendments totally dust & water proof for submersible duty isolated from the pump by intermediate casing with double mechanical seal in oil chamber chamber & grease packed lubricated bearings & provided with stainless steel thrust bearing plate to withstand non vertical loads with minimum wear & tear. It should also be fitted with a device to take up expansion of water with the heating of motor. The pump set should include water level guard, errection clamps, cable clips & depth gauge etc. & suitable for operation on data given below:- From Tube Well to Main Delivery tank. |
| 60 | Total Head in mtrs (i/c depth of Column Pipe in case of t/well) :118.34 m |
| 61 | Capacity (in LPS) of pump set. 7.80 LPS |
| 62 | Dia of R/Main (in mm) 100 mm |
| 63 | Dia of Column pipe (in mm) 80 mm |
| 64 | Length of R/Main. 180 |
| 65 | SITE CONDITIONS:- |
| 66 | Location of Site:- Village Jagatpur |
| 67 | The altitude of place in which the motor is intended to work:- 345.73 m |
| 68 | Humidity:- Wheather generally remains humid during monsoon season |
| 69 | Nature of atmosphere:- As normally encountered in Shivalik Ranges |
| 70 | Detail of quality of water :- Clear cold water |
| 71 | Water free from sand or not:- Yes |
| 72 | Water corosive or not:- Not |
| 73 | Turbidity :- 50ppm |
| 74 | Type of well:- Tube-well |
| 75 | Inside Dia :- 0.00 |
| 76 | Depth of water during HFL in the pond:- 0.00 |
| 77 | Max. draw down:- (Metres) 15.24 |
| 78 | Depth ofTubewell :- (Metres) 0.00 |
| 79 | Any other information or requirement:- ----- |
| 80 | OPERATING CONDITIONS:- |
| 81 | Type of current:- AC three/Sinle phase |
| 82 | Operating frequency:- 50HZ |
| 83 | Rated voltage:- 400 (+/-) 10% volts |
| 84 | System of earthing if any to to be adopted:- Doble loop earthing as per BIS 3043-2018 latest with upto date ammendments. |
| 85 | Speed of revolution:- To be quoted by tenderer |
| 86 | Direction of rotation:- To be quoted by tenderer |
| 87 | No. of working hours per day:- 20.00 Hours |
| 88 | The max. Temp. of cooling air & water in the place in which the pumpset is intented to work in ordinary service:- |
| 89 | MOTOR:- Generally warm |
| 90 | Ref to BIS code:- BIS 9283-2013 for submersible pump or latest with upto date ammendments energy effecient motor of BIS 14536-1998 minimum effeciency level IE-2 as per IS 12615-2011. |
| 91 | Type of enclosure of motor:- As per BIS 4691-1985 or latest with up to date ammendments |
| 92 | Type of duty:- \\"S1\\" i.e. Continuous duty type as per IS-12824-1989 or latest with up to date ammendments |
| 93 | Mechanical out put in KW:- Suitable for driving submersible pumps required for duties specified against pumps. To avoid overloading of motor a margin of about 15-20% may be kept in the rated out put of prime mover. |
| 94 | Class of insulation:- Class ~F~ |
| 95 | Max.permissible temp. rise of motor reqd. if different from that given in B (viii) above:- To be quoted by tenderer |
| 96 | Particulars of test reqd. & where they are to be conducted:-. As per terms & conditions attached |
| 97 | Particulars as to whether voltage limiting device will be employed:- Star Delta starter, as per IS 9283 and relevant IS 12615 ,fully automatic to be installed between bus bar & motor. Shunt capacitor is also proposed to be installed for improving the power factor at site. |
| 98 | (NOTE:- Star delta starter upto 37.5 KW & ATS for 37.5 KW & above) |
| 99 | Type of motor:- As per BIS 9283-2013 or latest with upto date ammendments |
| 100 | Details of shaft extension reqd:- To work with the pump offered |
| 101 | Breakway torque in terms of rated load torque & the corresponding breakway starting current which may be taken from the supply with the starting apparatus in circuit:- Breakway torque to be given by the tenderer but the starting current should not exceed 6 times of the full load current. |
| 102 | Nature of load & any information regarding the driven machine which has a bearing upon the torque reqd. during the accelerated period, the kinetic energy of the moving parts to be accelrated & No.of starts during a specified period:- To work the pump offered |
| 103 | Where possible fault capacity of the system to which the motor is connected:- The motor should be able to withstand initial current of 6times the rated current for 6 minutes without suffering damages or permanent deformations |
| 104 | PUMPS:- |
| 105 | Nos of pumps reqd.:- 1 No Pump |
| 106 | Spare parts required:- For two years normal maintenance as recommended by manufacturer. |
| 107 | Type of drive:- Electric induction motor |
| 108 | Optional fittings reqd.:- |
| 109 | PUMP OPERATING CONDITIONS:- |
| 110 | Capacity of pump (in lps) :- 7.80 |
| 111 | Total head (in Mts.) :- 118.34 |
| 112 | If total head is not known then following details be provided:- |
| 113 | i) Static head (in mtrs):- |
| 114 | ii) Minimum depth of water (in mtrs) :- |
| 115 | iii) Seasonal Variation in water level (in mtrs):- |
| 116 | iv) Ground level to max. water level (in mtrs) :- |
| 117 | v) Ground level to delivery point (in mtrs):- |
| 118 | vi) Pressure in the suction tank (in kg/cm^2)- |
| 119 | vii) Pressure in the delivery tank (in kg/cm^2) :- |
| 120 | Length of R/Main (in mtrs):- 180 |
| 121 | Dia of R/Main (in mm):- 100 |
| 122 | Length of Column pipe (in mtrs):- 70 m |
| 123 | Dia of Column pipe (in mtrs) 80 |
| 124 | Turbidity of water (in ppm):- 50ppm |
| 125 | Drive type:- Electric driven |
| 126 | Limits of total head in which the pump is reqd. to operate:- (-) 15% to (+) 10% of total head. |
| 127 | Suction/delivery size of pump:- To be specified by the tenderer |
| 128 | Efficiency of pump at To be specified by the tenderer |
| 129 | a) duty head 118.34 |
| 130 | b) (+) 10 % head 130.17 |
| 131 | c) (-) 15 % head 100.59 |
| 132 | Material of construction:- To be specified by the tenderer (manufacturers certficate to be appended) |
| 133 | Supplying and installation of suitable direct on line/ air back star delta/ ATS/ stator rotor starter of standard make such as MEI /Kilburn/ Jyoti/ Siemens /Larson & Tubro conforming to IS/IEC -60947-4-1 latest with up to date ammendments for squirrel cage/slip-ring motor (make to be specified by the tenderers) mounted on panel board with magnetic type over load release & dashpot,time lag,under voltage release with initial oil filling . |
| 134 | Note:- Star - delta - starter upto 37.5 KW , ATS between 37.5 KW to 50 KW and stater rotor starter with slipring motor beyond 50 KW. |
| 135 | Providing M.S. sheet 16 SWG steel fabricated floor mounted closed almirah type switch board including angle iron post of suitable height and size ISA 40x40x6mm duly painted comprising and capable of mounting including providing and fixing in position the following accessories with all internal electric connections. The drawing of panel board shall be subject to approval of Engineer in charge.Conforming to IS 61439-1&2 or latest edition |
| 136 | a). Ammeter AC supply,100 mm dia circular dial Auto electric/AE/IMP/Havells make of suitable range for above motor with selector switches conforming to BIS 1248-(P-II) 2003 and IS:61869-2 latest with up to date ammendments. |
| 137 | b). Voltmeter AC supply,100 mm dia circular dial Auto electric/AE/IMP/Havells make of suitable range for above motor with selector switches conforming to IS 60947-3 as per IS 1248 -02 or IS/IEC 609473 with up to date ammendments. |
| 138 | c).TPN switches SDF with HRC fuses of Kilburn/Larsen & Tubro/Standard/ Siemen/ Havells make and having capacity 30% extra of the operational rating of motor as per IS 60947-3 with upto date ammendments immediatly after the power meter of HPSEB. |
| 139 | d).Busbar chamber having three copper bars of suitable rating for full length equal to width of board of three live phases and one copper bar of half rating of full length for neutral conforming to IS 61439-2 and IS 1897 read with IS 60445 all latest with upto date ammendments. |
| 140 | e).ACB/ MCB/ Oil circuit breaker of suitable capacity of Kilburn/ L &T/ MEI/ GEC/ Standard make on incomming feeder for motors offered by the tenderer conforming to IS 63445 latest with upto date ammendments with initial oil filling whenever required & neutral linked under voltage release. |
| 141 | f).Three phase indicating lamps complete with toggle switches for individual motors conforming to IS 60947-5-1 latest with up to date ammendments. |
| 142 | g) Earth leakage circuit breaker/ relay of recommended make such as Kilburn / L&T/ MET/ GEC conforming to IS-60947-2 with upto date ammendments and of suitaible range which should have control box, oprating handel and trip/reset push button, on/ off indicators, re-indicating off spring condition of the circut breaker for over current protection. The circuit should be equipped with magnet thermal release with metallic tap CTS. It should also be fitted earth fault for tripping of breaker on occurance of earth fault on/ of breaker load side. |
| 143 | h).Hour run meter of reputed make of four digit capacity conforming to IS- 60947-5-1 (latest edition)/recommendations. |
| 144 | i).Suitable three phase voltage monitor relay with all protections & usual indicators with electric sirens against single phasing, low voltage, high voltage & overloading & phase voltage difference as per IS-60255-1 with up to date ammendments. |
| 145 | k).Single phase preventor of reputed make & suitable capacity conforming to IS:60947-5-1 read with IS 60947-8 with up to date ammendments |
| 146 | supply of Kirloskar/ Kilburn/ IVC/ Fouress/ Gled/ BHEL/ Leader/ Bir/ Kartar/ Pelicon make of cast iron/cast steel double flanged sluice valve having size one size higher than the nominal delivery size of pump and capable of withstanding nominal seat pressure as mentionmed in item No. 1(a) + surge pressure conforming to BIS/API-standard with up to date ammendments for delivery line of pump. The class of valve shall be ASA-300 conforming to API 600 specification. |
| 147 | Supply of Kirloskar/ Kilburn/ IVC/ Fouress/Gled/ BHEL/ Leader/ Bir/ Kartar/ Pelicon make of suitable size cast iron/cast steel double flanged swing check type reflux valve for delivery line of pump having bye pass arrangement & size one size higher than the nominal delivery size of pump and capable of withstanding nominal seat pressure as mentionmed in item No. 1(a) + surge pressure and conforming to BIS/API-standards with up to date ammendments for delivery line of pump. The class of valve shall be ASA-300 confirming to API-6D |
| 148 | a).Providing,laying,jointing & testing at site suitable size copper PVC insulated armoured power three & half core cable ( from meter of HPSEBL TO CIRCUIT BREAKER) conforming to IS 7098 or latest with up to date ammendments of Siemen/Gloster/ICC/ EICO/National /IEC make from meter of HPSEB to circuite breaker & from circuit breaker to bus bar switch & starter (one cable carrying all three phases) including all other electrical equipment/accessories such as thimbles,flexible pipe,solder, nuts & bolts,cable glands etc. laid in pipes or trenches under floor The type,size & make will be subject to approval of HPSEB authorities. In case of non acceptance by HPSEB authorities it shall have to be replaced by the tenderer free of cost. (30 Rmt.). The size of cable shall be 25 mm2 . |
| 149 | b).Providing,laying,jointing & testing at site PVC jointless flat water proof cable ( for Motor Side ) as per IS 7098-1 (latest with up to date ammendments) suitable for the pump sets offered from circuite breaker to motor & motor to starter including all other electrical equipments such as thimbles, flexible pipes, solder,nuts & bolts,cable glands etc. laid in pipes or trenches. The type,size & make will be subject to approval of HPSEB authorities.In case of non acceptance by HPSEB authorities it shall have to be replaced by the tenderer free of cost. (2x75 = 150 Rmt.) The size of cable shall be 16 mm2 . |
| 150 | Providing & laying at site double loop earthing with copper plate 600x600x3mm thick electrode complete with material such as charcoal, common salt ,GI pipes, thimbles, nuts & bolts,digging of pits,GI wiring & 25x5mm copper strips of required capacity conforming to BIS 3043-2018 latest with up to date ammendments suitable for above motors & other electrical equipments i/c cost of carriage of material in all leads & lifts & as directed by the Engineer-in-charge. |
| 151 | Supplying and fixing of 100 mm dia circular dial pressure gauge of suitable range & standard make such as Fiebeg/Bourden/ Precision/PREGA with all accessories such as stop cock,copper tubing etc.conforming to BIS 3624-2018 or latest with up to date ammendments. |
| 152 | Providing and lowering in position at site of GMS pipe (MG) column pipe assembly of size as indicated in item no.1d including MS flanges of table-17 capable to withstanding nominal pressure as mentioned in item no.1a & conforming to IS:6392-1971 with upto date ammendments including the cost of rubber/asbestos gasket of maximum 3 mm thickness as per IS: 2712-1979 and required numbers of nuts and bolts as per IS: 1364-1983. The column pipe should be provided & lowered as per the direction of Engineer-in-charge. The same shall be of suitable thickness,grade & specification capable of withstanding minimum 1.5 times the total presure as indicated in item no 1 a.unless otherwise specified properly jointed at every three mtrs including all necessary acessories like increaser/reducer,flanges,tees,bends etc.including supporting clamps (2 nos) at the top of assembly and i/c cost of jointing of column pipe with Rising main with additional length of delivery pipe of approximately 10 m as per the direction of Engineer-in-Charge ( 70+10 = 80 mtrs.). |
| 153 | Supply & errection of floor/wall mounted power factor shunt capacitor conforming to IS 1334 and IS 1341 or latest with upto date ammendments of BHEL/GEC/Machneil/ Mager/Bajaj/L&T make to raise the prevailing power factor at site to 0.95 for direct connection to induction motor individually,of required KVAR according to HP of motor offered including cable Siemens/Gloster/ICC make from busbar chamber to capacitor & also including L&T//Kilburn/Standard/Siemen/Havells make ICTP switches conforming to IS 60947-3 or latest with HRC fuses (Range to be specified by the tenderer) 7 KVAR capacity.i/c cost of carriage of material in all leads & lifts & as directed by the Engineer-in-charge.i/c cost of carriage of material in all leads & lifts & as directed by the Engineer-in-charge. |
| 154 | SUBMERSIBLE Pump set for Tube well Jagatpur-I :-Supply, erection, testing & commissioning of submersible/ mono submersible pump for tube well pumping set of reputed make such as KSB/ BS/Johnston / Clama/ SU/ Kirloskar or any other state/ department approved make conforming to latest relevent BIS code 8034 & IS 9283 for motor. The pump should be fitted with free flow impellers of bronze /suitable alloy as per IS 8034-2002 or latest with up to date ammendments suitable for raw water having greased packed bearings & shaft with wound stator on motor side & with shaft protection sleeve on pump side ensuring better life for shaft conforming to BIS specifications. The pump shall be directly coupled to a siutable submersible energy effecient motor of minimum effeciency level IE-2 of Kirloskar/ NGEF/ Jyoti / Crompton / BHEL/ GEC/ SIEMENS/ ABB/ MATHER & PLATmake conforming to relevent BIS code compatible with pump with up to date ammendments totally dust & water proof for submersible duty isolated from the pump by intermediate casing with double mechanical seal in oil chamber chamber & grease packed lubricated bearings & provided with stainless steel thrust bearing plate to withstand non vertical loads with minimum wear & tear. It should also be fitted with a device to take up expansion of water with the heating of motor. The pump set should include water level guard, errection clamps, cable clips & depth gauge etc. & suitable for operation on data given below:- From Tube Well to Main Delivery tank. |
| 155 | Total Head in mtrs (i/c depth of Column Pipe in case of t/well) :134.69 m |
| 156 | Capacity (in LPS) of pump set. 9.60 Lps |
| 157 | Dia of R/Main (in mm) 125 mm |
| 158 | Dia of Column pipe (in mm) 80 mm |
| 159 | Length of R/Main. 900 |
| 160 | SITE CONDITIONS:- |
| 161 | Location of Site:- Village Jagatpur |
| 162 | The altitude of place in which the motor is intended to work:- 315.00 m |
| 163 | Humidity:- Wheather generally remains humid during monsoon season |
| 164 | Nature of atmosphere:- As normally encountered in Shivalik Ranges |
| 165 | Detail of quality of water :- Clear cold water |
| 166 | Water free from sand or not:- Yes |
| 167 | Water corosive or not:- Not |
| 168 | Turbidity :- 50ppm |
| 169 | Type of well:- Tube-well |
| 170 | Inside Dia :- 00 |
| 171 | Depth of water during HFL in the pond:- 00 |
| 172 | Max. draw down:- (Metres) 18.30 |
| 173 | Depth ofTubewell :- (Metres) 0.0 |
| 174 | Any other information or requirement:- ----- |
| 175 | OPERATING CONDITIONS:- |
| 176 | Type of current:- AC three/single phase |
| 177 | Operating frequency:- 50 HZ |
| 178 | Rated voltage:- 400 (+/-) 10% volts |
| 179 | System of earthing if any to to be adopted:- Double loop earthing as per BIS 3043-2018 latest with upto date ammendments |
| 180 | Speed of revolution:- To be quoted by tenderer |
| 181 | Direction of rotation:- To be quoted by tenderer |
| 182 | No. of working hours per day:- 20.00 Hours |
| 183 | The max. Temp. of cooling air & water in the place in which the pumpset is intented to work in ordinary service:- |
| 184 | MOTOR:-Generally warm |
| 185 | Ref to BIS code:- BIS 9283-2013 for submersible pump (read with BIS 14536-1998) or latest with upto date ammendments energy effecient motor of BIS 14536-1998 minimum effeciency level IE-2 as per IS 12615-2011. |
| 186 | Type of enclosure of motor:- As per BIS 4691-1985 or latest with up to date ammendments |
| 187 | Type of duty:- \\"S1\\" i.e. Continuous duty type as per IS-12824-1989 or latest with up to date ammendments |
| 188 | Mechanical out put in KW:- Suitable for driving submersible pumps required for duties specified against pumps. To avoid overloading of motor a margin of about 15-20% may be kept in the rated out put of prime mover. |
| 189 | Class of insulation:- Class ~F~ |
| 190 | Max.permissible temp. rise of motor reqd. if different from that given in B (viii) above:- To be quoted by tenderer |
| 191 | Particulars of test reqd. & where they are to be conducted:-. As per terms & conditions attached |
| 192 | Particulars as to whether voltage limiting device will be employed:- Star Delta starter, as per IS 9283 and relevant IS 12615 ,fully automatic to be installed between bus bar & motor. Shunt capacitor is also proposed to be installed for improving the power factor at site. |
| 193 | (NOTE:- Star delta starter upto 37.5 KW & ATS for 37.5 KW & above) |
| 194 | Type of motor:- As per BIS 9283-2013 or latest with upto date ammendments |
| 195 | Details of shaft extension reqd:- To work with the pump offered |
| 196 | Breakway torque in terms of rated load torque & the corresponding breakway starting current which may be taken from the supply with the starting apparatus in circuit:- Breakway torque to be given by the tenderer but the starting current should not exceed 6 times of the full load current. |
| 197 | Nature of load & any information regarding the driven machine which has a bearing upon the torque reqd. during the accelerated period, the kinetic energy of the moving parts to be accelrated & No.of starts during a specified period:- To work the pump offered |
| 198 | Where possible fault capacity of the system to which the motor is connected:- The motor should be able to withstand initial current of 6times the rated current for 6 minutes without suffering damages or permanent deformations |
| 199 | PUMPS:- |
| 200 | Nos of pumps reqd.:- 1 No Pump |
| 201 | Spare parts required:- For two years normal maintenance as recommended by manufacturer. |
| 202 | Type of drive:- Electric induction motor |
| 203 | Optional fittings reqd.:- |
| 204 | PUMP OPERATING CONDITIONS:- |
| 205 | Capacity of pump (in lps) :- 9.60 LPS |
| 206 | Total head (in Mts.) :- 134.69 |
| 207 | If total head is not known then following details be provided:- |
| 208 | i) Static head (in mtrs):- |
| 209 | ii) Minimum depth of water (in mtrs) :- |
| 210 | iii) Seasonal Variation in water level (in mtrs):- |
| 211 | iv) Ground level to max. water level (in mtrs) :- |
| 212 | v) Ground level to delivery point (in mtrs):- |
| 213 | vi) Pressure in the suction tank (in kg/cm^2)- |
| 214 | vii) Pressure in the delivery tank (in kg/cm^2) :- |
| 215 | Length of R/Main (in mtrs):- 900 |
| 216 | Dia of R/Main (in mm):- 125mm |
| 217 | Length of Column pipe (in mtrs):- 76 m |
| 218 | Dia of Column pipe (in mtrs) 80 |
| 219 | Turbidity of water (in ppm):- 50ppm |
| 220 | Drive type:- Electric driven |
| 221 | Limits of total head in which the pump is reqd. to operate:- (-) 15% to (+) 10% of total head. |
| 222 | Suction/delivery size of pump:- To be specified by the tenderer |
| 223 | Efficiency of pump at To be specified by the tenderer |
| 224 | a) duty head 134.69 |
| 225 | b) (+) 10 % head 148.16 |
| 226 | c) (-) 15 % head 114.49 |
| 227 | Material of construction:- To be specified by the tenderer (manufacturers certficate to be appended) |
| 228 | Supplying and installation of suitable direct on line/ air back star delta/ ATS/ stator rotor starter of standard make such as MEI /Kilburn/ Jyoti/ Siemens /Larson & Tubro conforming to IS-60947-4-1 latest with up to date ammendments for squirrel cage/slip-ring motor (make to be specified by the tenderers) mounted on panel board with magnetic type over load release & dashpot,time lag,under voltage release with initial oil filling . |
| 229 | Note:- Star - delta - starter upto 37.5 KW , ATS between 37.5 KW to 50 KW and stater rotor starter with slipring motor beyond 50 KW. |
| 230 | Providing M.S. sheet 16 SWG steel fabricated floor mounted closed almirah type switch board including angle iron post of suitable height and size ISA 40x40x6mm duly painted comprising and capable of mounting including providing and fixing in position the following accessories with all internal electric connections. The drawing of panel board shall be subject to approval of Engineer in charge.Conforming to IS 61439-1&2 or latest edition |
| 231 | a). Ammeter AC supply,100 mm dia circular dial Auto electric/AE/IMP/Havells make of suitable range for above motor with selector switches conforming to BIS 1248-(P-II) 2003 and IS:61869-2 latest with up to date ammendments. |
| 232 | b). Voltmeter AC supply,100 mm dia circular dial Auto electric/AE/IMP/Havells make of suitable range for above motor with selector switches conforming to IS 60947-3 as per IS 1248 or IS 60947 with up to date ammendments. |
| 233 | c).TPN switches SDF with HRC fuses of Kilburn/Larsen & Tubro/Standard/ Siemen/ Havells make and having capacity 30% extra of the operational rating of motor as per IS/IEC 60445 with upto date ammendments immediatly after the power meter of HPSEB. |
| 234 | d).Busbar chamber having three copper bars of suitable rating for full length equal to width of board of three live phases and one copper bar of half rating of full length for neutral conforming to IS 61439-2 and IS 1897 read with IS 60445 all latest with upto date ammendments. |
| 235 | e).ACB/ MCB/ Oil circuit breaker of suitable capacity of Kilburn/ L &T/ MEI/ GEC/ Standard make on incomming feeder for motors offered by the tenderer conforming to IS 60947-2 latest with upto date ammendments with initial oil filling whenever required & neutral linked under voltage release. |
| 236 | f).Three phase indicating lamps complete with toggle switches for individual motors conforming to IS 60947-5-1 latest with up to date ammendments. |
| 237 | g) Earth leakage circuit breaker/ relay of recommended make such as Kilburn / L&T/ MET/ GEC conforming to IS-60947-2 with upto date ammendments and of suitaible range which should have control box, oprating handel and trip/reset push button, on/ off indicators, re-indicating off spring condition of the circut breaker for over current protection. The circuit should be equipped with magnet thermal release with metallic tap CTS. It should also be fitted earth fault for tripping of breaker on occurance of earth fault on/ of breaker load side. |
| 238 | h).Hour run meter of reputed make of four digit capacity conforming to IS- 60947-5-1 (latest edition)/recommendations. |
| 239 | i).Suitable three phase voltage monitor relay with all protections & usual indicators with electric sirens against single phasing, low voltage, high voltage & overloading & phase voltage difference as per IS-60255-1 with up to date ammendments. |
| 240 | k).Single phase preventor of reputed make & suitable capacity conforming to IS:60947-5-1 read with IS 60947-8 with up to date ammendments |
| 241 | supply of Kirloskar/ Kilburn/ IVC/ Fouress/ Gled/ BHEL/ Leader/ Bir/ Kartar/ Pelicon make of cast iron/cast steel double flanged sluice valve having size one size higher than the nominal delivery size of pump and capable of withstanding nominal seat pressure as mentionmed in item No. 1(a) + surge pressure conforming to BIS/API-standard with up to date ammendments for delivery line of pump. The class of valve shall be ASA-300 conforming to API 600 specification. |
| 242 | Supply of Kirloskar/ Kilburn/ IVC/ Fouress/Gled/ BHEL/ Leader/ Bir/ Kartar/ Pelicon make of suitable size cast iron/cast steel double flanged swing check type reflux valve for delivery line of pump having bye pass arrangement & size one size higher than the nominal delivery size of pump and capable of withstanding nominal seat pressure as mentionmed in item No. 1(a) + surge pressure and conforming to BIS/API-standards with up to date ammendments for delivery line of pump. The class of valve shall be ASA-300 confirming to API-6D |
| 243 | a).Providing,laying,jointing & testing at site suitable size copper PVC insulated armoured power three & half core cable ( from meter of HPSEBL TO CIRCUIT BREAKER) conforming to IS 7098 or latest with up to date ammendments of Siemen/Gloster/ICC/ EICO/National /IEC make from meter of HPSEB to circuite breaker & from circuit breaker to bus bar switch & starter (one cable carrying all three phases) including all other electrical equipment/accessories such as thimbles,flexible pipe,solder, nuts & bolts,cable glands etc. laid in pipes or trenches under floor The type,size & make will be subject to approval of HPSEB authorities. In case of non acceptance by HPSEB authorities it shall have to be replaced by the tenderer free of cost. (30 Rmt.). The size of cable shall be 35 mm2 . |
| 244 | b).Providing,laying,jointing & testing at site PVC jointless flat water proof cable ( for Motor Side ) as per IS 7098-1 (latest with up to date ammendments) suitable for the pump sets offered from circuite breaker to motor & motor to starter including all other electrical equipments such as thimbles, flexible pipes, solder,nuts & bolts,cable glands etc. laid in pipes or trenches. The type,size & make will be subject to approval of HPSEB authorities.In case of non acceptance by HPSEB authorities it shall have to be replaced by the tenderer free of cost. (2x81 = 162 Rmt.) The size of cable shall be 25 mm2 . |
| 245 | Providing & laying at site double loop earthing with copper plate 600x600x3mm thick electrode complete with material such as charcoal, common salt ,GI pipes, thimbles, nuts & bolts,digging of pits,GI wiring & 25x5mm copper strips of required capacity conforming to BIS 3043-2018 latest with up to date ammendments suitable for above motors & other electrical equipments i/c cost of carriage of material in all leads & lifts & as directed by the Engineer-in-charge. |
| 246 | Supplying and fixing of 100 mm dia circular dial pressure gauge of suitable range & standard make such as Fiebeg/Bourden/ Precision/PREGA with all accessories such as stop cock,copper tubing etc.conforming to BIS 3624-2018 or latest with up to date ammendments. |
| 247 | Providing and lowering in position at site of GMS pipe (MG) column pipe assembly of size as indicated in item no.1d including MS flanges of table-17 capable to withstanding nominal pressure as mentioned in item no.1a & conforming to IS:6392-1971 with upto date ammendments including the cost of rubber/asbestos gasket of maximum 3 mm thickness as per IS: 2712-1979 and required numbers of nuts and bolts as per IS: 1364-1983. The column pipe should be provided & lowered as per the direction of Engineer-in-charge. The same shall be of suitable thickness,grade & specification capable of withstanding minimum 1.5 times the total presure as indicated in item no 1 a.unless otherwise specified properly jointed at every three mtrs including all necessary acessories like increaser/reducer,flanges,tees,bends etc.including supporting clamps (2 nos) at the top of assembly and i/c cost of jointing of column pipe with Rising main with additional length of delivery pipe of approximately 10 m as per the direction of Engineer-in-Charge ( 76+10 = 86 mtrs.). |
| 248 | Supply & errection of floor/wall mounted power factor shunt capacitor conforming to IS 1334 and IS 1341 or latest with upto date ammendments of BHEL/GEC/Machneil/ Mager/Bajaj/L&T make to raise the prevailing power factor at site to 0.95 for direct connection to induction motor individually,of required KVAR according to HP of motor offered including cable Siemens/Gloster/ICC make from busbar chamber to capacitor & also including L&T//Kilburn/Standard/Siemen/Havells make ICTP switches conforming to IS 60947-3 or latest with HRC fuses (Range to be specified by the tenderer) 9 KVAR capacity.i/c cost of carriage of material in all leads & lifts & as directed by the Engineer-in-charge.i/c cost of carriage of material in all leads & lifts & as directed by the Engineer-in-charge. |
| 249 | SUBMERSIBLE Pump set for Tube well Baruna. :- Supply, erection, testing & commissioning of submersible/ mono submersible pump for tube well pumping set of reputed make such as KSB/ BS/Johnston / Clama/ SU/ Kirloskar or any other state/ department approved make conforming to latest relevent BIS code 8034 & IS 9283 for motor. The pump should be fitted with free flow impellers of bronze /suitable alloy as per IS 8034-2002 or latest with up to date ammendments suitable for raw water having greased packed bearings & shaft with wound stator on motor side & with shaft protection sleeve on pump side ensuring better life for shaft conforming to BIS specifications. The pump shall be directly coupled to a siutable submersible energy effecient motor of minimum effeciency level IE-2 of Kirloskar/ NGEF/ Jyoti / Crompton / BHEL/ GEC/ SIEMENS/ ABB/ MATHER & PLATmake conforming to relevent BIS code compatible with pump with up to date ammendments totally dust & water proof for submersible duty isolated from the pump by intermediate casing with double mechanical seal in oil chamber chamber & grease packed lubricated bearings & provided with stainless steel thrust bearing plate to withstand non vertical loads with minimum wear & tear. It should also be fitted with a device to take up expansion of water with the heating of motor. The pump set should include water level guard, errection clamps, cable clips & depth gauge etc. & suitable for operation on data given below:- From Tube Well to Main Delivery tank. |
| 250 | Total Head in mtrs (i/c depth of Column Pipe in case of t/well) : 105.34 m |
| 251 | Capacity (in LPS) of pump set. 21 Lps |
| 252 | Dia of R/Main (in mm) 150 mm |
| 253 | Dia of Column pipe (in mm) 125mm |
| 254 | Length of R/Main. 410 |
| 255 | SITE CONDITIONS:- |
| 256 | Location of Site:- Village Baruna |
| 257 | The altitude of place in which the motor is intended to work:- 306.00 m |
| 258 | Humidity:- Wheather generally remains humid during monsoon season |
| 259 | Nature of atmosphere:- As normally encountered in Shivalik Ranges |
| 260 | Detail of quality of water :- Clear cold water |
| 261 | Water free from sand or not:- Yes |
| 262 | Water corosive or not:- Not |
| 263 | Turbidity :- 50PPM |
| 264 | Type of well:- T/Well |
| 265 | Inside Dia :- 00 |
| 266 | Depth of water during HFL in the pond:- 00 |
| 267 | Max. draw down:- (Metres) 15.24 |
| 268 | Depth ofTubewell :- (Metres) 0.00 |
| 269 | Any other information or requirement:- ----- |
| 270 | OPERATING CONDITIONS:- |
| 271 | Type of current:- AC three/single phase |
| 272 | Operating frequency:- 50 HZ |
| 273 | Rated voltage:- 400 (+/-) 10% volts |
| 274 | System of earthing if any to to be adopted:- Double loop earthing as per BIS 3043-2018 latest with upto date ammendments |
| 275 | Speed of revolution:- To be quoted by tenderer |
| 276 | Direction of rotation:- To be quoted by tenderer |
| 277 | No. of working hours per day:- 20 Hours |
| 278 | The max. Temp. of cooling air & water in the place in which the pumpset is intented to work in ordinary service:- |
| 279 | MOTOR:-Generally warm |
| 280 | Ref to BIS code:- BIS 9283-2013 for submersible pump (read with BIS 14536-1998) or latest with upto date ammendments energy effecient motor of BIS 14536-1998 minimum effeciency level IE-2 as per IS 12615-2011. |
| 281 | Type of enclosure of motor:- As per BIS 4691-1985 or latest with up to date ammendments |
| 282 | Type of duty:- \\"S1\\" i.e. Continuous duty type as per IS-12824-1989 or latest with up to date ammendments |
| 283 | Mechanical out put in KW:- Suitable for driving submersible pumps required for duties specified against pumps. To avoid overloading of motor a margin of about 15-20% may be kept in the rated out put of prime mover. |
| 284 | Class of insulation:- Class ~F~ |
| 285 | Max.permissible temp. rise of motor reqd. if different from that given in B (viii) above:- To be quoted by tenderer |
| 286 | Particulars of test reqd. & where they are to be conducted:-. As per terms & conditions attached |
| 287 | Particulars as to whether voltage limiting device will be employed:- Star Delta starter, as per IS 9283 and relevant IS 12615 ,fully automatic to be installed between bus bar & motor. Shunt capacitor is also proposed to be installed for improving the power factor at site. |
| 288 | (NOTE:- Star delta starter upto 37.5 KW & ATS for 37.5 KW & above) |
| 289 | Type of motor:- As per BIS 9283-2013 or latest with upto date ammendments |
| 290 | Details of shaft extension reqd:- To work with the pump offered |
| 291 | Breakway torque in terms of rated load torque & the corresponding breakway starting current which may be taken from the supply with the starting apparatus in circuit:- Breakway torque to be given by the tenderer but the starting current should not exceed 6 times of the full load current. |
| 292 | Nature of load & any information regarding the driven machine which has a bearing upon the torque reqd. during the accelerated period, the kinetic energy of the moving parts to be accelrated & No.of starts during a specified period:- To work the pump offered |
| 293 | Where possible fault capacity of the system to which the motor is connected:- The motor should be able to withstand initial current of 6times the rated current for 6 minutes without suffering damages or permanent deformations |
| 294 | PUMPS:- |
| 295 | Nos of pumps reqd.:- 1 No Pump |
| 296 | Spare parts required:- For two years normal maintenance as recommended by manufacturer. |
| 297 | Type of drive:- Electric induction motor |
| 298 | Optional fittings reqd.:- |
| 299 | PUMP OPERATING CONDITIONS:- |
| 300 | Capacity of pump (in lps) :- |
| 301 | Total head (in Mts.) :- |
| 302 | If total head is not known then following details be provided:- |
| 303 | i) Static head (in mtrs):- |
| 304 | ii) Minimum depth of water (in mtrs) :- |
| 305 | iii) Seasonal Variation in water level (in mtrs):- |
| 306 | iv) Ground level to max. water level (in mtrs) :- |
| 307 | v) Ground level to delivery point (in mtrs):- |
| 308 | vi) Pressure in the suction tank (in kg/cm^2)- |
| 309 | vii) Pressure in the delivery tank (in kg/cm^2) :- |
| 310 | Length of R/Main (in mtrs):- 0 |
| 311 | Dia of R/Main (in mm):- 0 |
| 312 | Length of Column pipe (in mtrs):- 55 m |
| 313 | Dia of Column pipe (in mtrs) 0 |
| 314 | Turbidity of water (in ppm):- 50 ppm |
| 315 | Drive type:- Electric driven |
| 316 | Limits of total head in which the pump is reqd. to operate:- (-) 15% to (+) 10% of total head. |
| 317 | Suction/delivery size of pump:- To be specified by the tenderer |
| 318 | Efficiency of pump at To be specified by the tenderer |
| 319 | a) duty head 105.74 |
| 320 | b) (+) 10 % head 115.87 |
| 321 | c) (-) 15 % head 99.54 |
| 322 | Material of construction:- To be specified by the tenderer (manufacturers certficate to be appended) |
| 323 | Supplying and installation of suitable direct on line/ air back star delta/ ATS/ stator rotor starter of standard make such as MEI /Kilburn/ Jyoti/ Siemens /Larson & Tubro conforming to IS-60947-4-1 latest with up to date ammendments for squirrel cage/slip-ring motor (make to be specified by the tenderers) mounted on panel board with magnetic type over load release & dashpot,time lag,under voltage release with initial oil filling . |
| 324 | Note:- Star - delta - starter upto 37.5 KW , ATS between 37.5 KW to 50 KW and stater rotor starter with slipring motor beyond 50 KW. |
| 325 | Providing M.S. sheet 16 SWG steel fabricated floor mounted closed almirah type switch board including angle iron post of suitable height and size ISA 40x40x6mm duly painted comprising and capable of mounting including providing and fixing in position the following accessories with all internal electric connections. The drawing of panel board shall be subject to approval of Engineer in charge.Conforming to IS 61439-1&2 or latest edition |
| 326 | a). Ammeter AC supply,100 mm dia circular dial Auto electric/AE/IMP/Havells make of suitable range for above motor with selector switches conforming to BIS 1248-(P-II)1983 and IS:61869-2 latest with up to date ammendments. |
| 327 | b). Voltmeter AC supply,100 mm dia circular dial Auto electric/AE/IMP/Havells make of suitable range for above motor with selector switches conforming to IS 60947-3 as per IS 1248 or IS 61010-1 with up to date ammendments. |
| 328 | c).TPN switches SDF with HRC fuses of Kilburn/Larsen & Tubro/Standard/ Siemen/ Havells make and having capacity 30% extra of the operational rating of motor as per IS 60947-3 with upto date ammendments immediatly after the power meter of HPSEB. |
| 329 | d).Busbar chamber having three copper bars of suitable rating for full length equal to width of board of three live phases and one copper bar of half rating of full length for neutral conforming to IS 61439-2 and IS 1897 read with IS 60445 all latest with upto date ammendments. |
| 330 | e).ACB/ MCB/ Oil circuit breaker of suitable capacity of Kilburn/ L &T/ MEI/ GEC/ Standard make on incomming feeder for motors offered by the tenderer conforming to IS 60947-2 latest with upto date ammendments with initial oil filling whenever required & neutral linked under voltage release. |
| 331 | f).Three phase indicating lamps complete with toggle switches for individual motors conforming to IS 60947-5-1 latest with up to date ammendments. |
| 332 | g) Earth leakage circuit breaker/ relay of recommended make such as Kilburn / L&T/ MET/ GEC conforming to IS-60947-2 with upto date ammendments and of suitaible range which should have control box, oprating handel and trip/reset push button, on/ off indicators, re-indicating off spring condition of the circut breaker for over current protection. The circuit should be equipped with magnet thermal release with metallic tap CTS. It should also be fitted earth fault for tripping of breaker on occurance of earth fault on/ of breaker load side. |
| 333 | h).Hour run meter of reputed make of four digit capacity conforming to IS- 60947-5-1 (latest edition)/recommendations. |
| 334 | i).Suitable three phase voltage monitor relay with all protections & usual indicators with electric sirens against single phasing, low voltage, high voltage & overloading & phase voltage difference as per IS-60255-1 with up to date ammendments. |
| 335 | k).Single phase preventor of reputed make & suitable capacity conforming to IS:60947-5-1 read with IS 60947-8 with up to date ammendments |
| 336 | supply of Kirloskar/ Kilburn/ IVC/ Fouress/ Gled/ BHEL/ Leader/ Bir/ Kartar/ Pelicon make of cast iron/cast steel double flanged sluice valve having size one size higher than the nominal delivery size of pump and capable of withstanding nominal seat pressure as mentionmed in item No. 1(a) + surge pressure conforming to BIS/API-standard with up to date ammendments for delivery line of pump. The class of valve shall be ASA-300 conforming to API 600 specification. |
| 337 | Supply of Kirloskar/ Kilburn/ IVC/ Fouress/Gled/ BHEL/ Leader/ Bir/ Kartar/ Pelicon make of suitable size cast iron/cast steel double flanged swing check type reflux valve for delivery line of pump having bye pass arrangement & size one size higher than the nominal delivery size of pump and capable of withstanding nominal seat pressure as mentionmed in item No. 1(a) + surge pressure and conforming to BIS/API-standards with up to date ammendments for delivery line of pump. The class of valve shall be ASA-300 confirming to API-6D |
| 338 | a).Providing,laying,jointing & testing at site suitable size copper PVC insulated armoured power three & half core cable ( from meter of HPSEBL TO CIRCUIT BREAKER) conforming to IS 7098 or latest with up to date ammendments of Siemen/Gloster/ICC/ EICO/National /IEC make from meter of HPSEB to circuite breaker & from circuit breaker to bus bar switch & starter (one cable carrying all three phases) including all other electrical equipment/accessories such as thimbles,flexible pipe,solder, nuts & bolts,cable glands etc. laid in pipes or trenches under floor The type,size & make will be subject to approval of HPSEB authorities. In case of non acceptance by HPSEB authorities it shall have to be replaced by the tenderer free of cost. (30 Rmt.). The size of cable shall be 90 mm2 . |
| 339 | b).Providing,laying,jointing & testing at site PVC jointless flat water proof cable ( for Motor Side ) as per IS 7098-1 (latest with up to date ammendments) suitable for the pump sets offered from circuite breaker to motor & motor to starter including all other electrical equipments such as thimbles, flexible pipes, solder,nuts & bolts,cable glands etc. laid in pipes or trenches. The type,size & make will be subject to approval of HPSEB authorities.In case of non acceptance by HPSEB authorities it shall have to be replaced by the tenderer free of cost. (2x60 = 120 Rmt.) The size of cable shall be 50 mm2 . |
| 340 | Providing & laying at site double loop earthing with copper plate 600x600x3mm thick electrode complete with material such as charcoal, common salt ,GI pipes, thimbles, nuts & bolts,digging of pits,GI wiring & 25x5mm copper strips of required capacity conforming to BIS 3043-12018 latest with up to date ammendments suitable for above motors & other electrical equipments i/c cost of carriage of material in all leads & lifts & as directed by the Engineer-in-charge. |
| 341 | Supplying and fixing of 100 mm dia circular dial pressure gauge of suitable range & standard make such as Fiebeg/Bourden/ Precision/PREGA with all accessories such as stop cock,copper tubing etc.conforming to BIS 3624-2018 or latest with up to date ammendments. |
| 342 | Providing and lowering in position at site of GMS pipe (MG) column pipe assembly of size as indicated in item no.1d including MS flanges of table-17 capable to withstanding nominal pressure as mentioned in item no.1a & conforming to IS:6392-1971 with upto date ammendments including the cost of rubber/asbestos gasket of maximum 3 mm thickness as per IS: 2712-1979 and required numbers of nuts and bolts as per IS: 1364-1983. The column pipe should be provided & lowered as per the direction of Engineer-in-charge. The same shall be of suitable thickness,grade & specification capable of withstanding minimum 1.5 times the total presure as indicated in item no 1 a.unless otherwise specified properly jointed at every three mtrs including all necessary acessories like increaser/reducer,flanges,tees,bends etc.including supporting clamps (2 nos) at the top of assembly and i/c cost of jointing of column pipe with Rising main with additional length of delivery pipe of approximately 10 m as per the direction of Engineer-in-Charge ( 55+10 = 65 mtrs.). |
| 343 | Supply & errection of floor/wall mounted power factor shunt capacitor conforming to IS 1334 and IS 1341 or latest with upto date ammendments of BHEL/GEC/Machneil/ Mager/Bajaj/L&T make to raise the prevailing power factor at site to 0.95 for direct connection to induction motor individually,of required KVAR according to HP of motor offered including cable Siemens/Gloster/ICC make from busbar chamber to capacitor & also including L&T//Kilburn/Standard/Siemen/Havells make ICTP switches conforming to IS 60947-3 or latest with HRC fuses (Range to be specified by the tenderer) 16 KVAR capacity.i/c cost of carriage of material in all leads & lifts & as directed by the Engineer-in-charge.i/c cost of carriage of material in all leads & lifts & as directed by the Engineer-in-charge. |
| 344 | SUBMERSIBLE Pump set for Tube well Thoda:- Supply, erection, testing & commissioning of submersible/ mono submersible pump for tube well pumping set of reputed make such as KSB/ BS/Johnston / Clama/ SU/ Kirloskar or any other state/ department approved make conforming to latest relevent BIS code 8034 & IS 9283 for motor. The pump should be fitted with free flow impellers of bronze /suitable alloy as per IS 8034-2002 or latest with up to date ammendments suitable for raw water having greased packed bearings & shaft with wound stator on motor side & with shaft protection sleeve on pump side ensuring better life for shaft conforming to BIS specifications. The pump shall be directly coupled to a siutable submersible energy effecient motor of minimum effeciency level IE-2 of Kirloskar/ NGEF/ Jyoti / Crompton / BHEL/ GEC/ SIEMENS/ ABB/ MATHER & PLATmake conforming to relevent BIS code compatible with pump with up to date ammendments totally dust & water proof for submersible duty isolated from the pump by intermediate casing with double mechanical seal in oil chamber chamber & grease packed lubricated bearings & provided with stainless steel thrust bearing plate to withstand non vertical loads with minimum wear & tear. It should also be fitted with a device to take up expansion of water with the heating of motor. The pump set should include water level guard, errection clamps, cable clips & depth gauge etc. & suitable for operation on data given below:- From Tube Well to Main Delivery tank. |
| 345 | Total Head in mtrs (i/c depth of Column Pipe in case of t/well) : 82.73 m |
| 346 | Capacity (in LPS) of pump set.6.60 Lps |
| 347 | Dia of R/Main (in mm) 100.00mm |
| 348 | Dia of Column pipe (in mm) 80 mm |
| 349 | Length of R/Main. 240 |
| 350 | SITE CONDITIONS:- |
| 351 | Location of Site:- Village Thoda near bridge |
| 352 | The altitude of place in which the motor is intended to work:- 322.10 m |
| 353 | Humidity:- Wheather generally remains humid during monsoon season |
| 354 | Nature of atmosphere:- As normally encountered in Shivalik Ranges |
| 355 | Detail of quality of water :- Clear cold water |
| 356 | Water free from sand or not:- Yes |
| 357 | Water corosive or not:- Not |
| 358 | Turbidity :- 50 ppm |
| 359 | Type of well:- T/Well |
| 360 | Inside Dia :- 00 |
| 361 | Depth of water during HFL in the pond:- 00 |
| 362 | Max. draw down:- (Metres) 12.80 |
| 363 | Depth ofTubewell :- (Metres) 00 |
| 364 | Any other information or requirement:- ----- |
| 365 | OPERATING CONDITIONS:- |
| 366 | Type of current:- AC three/single phase |
| 367 | Operating frequency:- 50 HZ |
| 368 | Rated voltage:- 400 (+/-) 10% volts |
| 369 | System of earthing if any to to be adopted:- Double loop earthing as per BIS 3043-2018 latest with upto date ammendments |
| 370 | Speed of revolution:- To be quoted by tenderer |
| 371 | Direction of rotation:- To be quoted by tenderer |
| 372 | No. of working hours per day:- 20.00 Hours |
| 373 | The max. Temp. of cooling air & water in the place in which the pumpset is intented to work in ordinary service:- |
| 374 | MOTOR:-Generally warm |
| 375 | Ref to BIS code:- BIS 9283-2013 for submersible pump (read with BIS 14536-1998) or latest with upto date ammendments energy effecient motor of BIS 14536-1998 minimum effeciency level IE-2 as per IS 12615-2011. |
| 376 | Type of enclosure of motor:- As per BIS 4691-1985 or latest with up to date ammendments |
| 377 | Type of duty:- \\"S1\\" i.e. Continuous duty type as per IS-12824-1989 or latest with up to date ammendments |
| 378 | Mechanical out put in KW:- Suitable for driving submersible pumps required for duties specified against pumps. To avoid overloading of motor a margin of about 15-20% may be kept in the rated out put of prime mover. |
| 379 | Class of insulation:- Class ~F~ |
| 380 | Max.permissible temp. rise of motor reqd. if different from that given in B (viii) above:- To be quoted by tenderer |
| 381 | Particulars of test reqd. & where they are to be conducted:-. As per terms & conditions attached |
| 382 | Particulars as to whether voltage limiting device will be employed:- Star Delta starter, as per IS 9283 and relevant IS 12615 ,fully automatic to be installed between bus bar & motor. Shunt capacitor is also proposed to be installed for improving the power factor at site. |
| 383 | (NOTE:- Star delta starter upto 37.5 KW & ATS for 37.5 KW & above) |
| 384 | Type of motor:- As per BIS 9283-2013 or latest with upto date ammendments |
| 385 | Details of shaft extension reqd:- To work with the pump offered |
| 386 | Breakway torque in terms of rated load torque & the corresponding breakway starting current which may be taken from the supply with the starting apparatus in circuit:- Breakway torque to be given by the tenderer but the starting current should not exceed 6 times of the full load current. |
| 387 | Nature of load & any information regarding the driven machine which has a bearing upon the torque reqd. during the accelerated period, the kinetic energy of the moving parts to be accelrated & No.of starts during a specified period:- To work the pump offered |
| 388 | Where possible fault capacity of the system to which the motor is connected:- The motor should be able to withstand initial current of 6times the rated current for 6 minutes without suffering damages or permanent deformations |
| 389 | PUMPS:- |
| 390 | Nos of pumps reqd.:- 1 No Pump |
| 391 | Spare parts required:- For two years normal maintenance as recommended by manufacturer. |
| 392 | Type of drive:- Electric induction motor |
| 393 | Optional fittings reqd.:- |
| 394 | PUMP OPERATING CONDITIONS:- |
| 395 | Capacity of pump (in lps) :- 6.60 |
| 396 | Total head (in Mts.) :- 82.73 |
| 397 | If total head is not known then following details be provided:- |
| 398 | i) Static head (in mtrs):- |
| 399 | ii) Minimum depth of water (in mtrs) :- |
| 400 | iii) Seasonal Variation in water level (in mtrs):- |
| 401 | iv) Ground level to max. water level (in mtrs) :- |
| 402 | v) Ground level to delivery point (in mtrs):- |
| 403 | vi) Pressure in the suction tank (in kg/cm^2)- |
| 404 | vii) Pressure in the delivery tank (in kg/cm^2) :- |
| 405 | Length of R/Main (in mtrs):- 240 |
| 406 | Dia of R/Main (in mm):- 100 |
| 407 | Length of Column pipe (in mtrs):- 55 m |
| 408 | Dia of Column pipe (in mtrs) 80.00 |
| 409 | Turbidity of water (in ppm):- 50 ppm |
| 410 | Drive type:- Electric driven |
| 411 | Limits of total head in which the pump is reqd. to operate:- (-) 15% to (+) 10% of total head. |
| 412 | Suction/delivery size of pump:- To be specified by the tenderer |
| 413 | Efficiency of pump at To be specified by the tenderer |
| 414 | a) duty head 82.73 |
| 415 | b) (+) 10 % head 91.00 |
| 416 | c) (-) 15 % head 70.32 |
| 417 | Material of construction:- To be specified by the tenderer (manufacturers certficate to be appended) |
| 418 | Supplying and installation of suitable direct on line/ air back star delta/ ATS/ stator rotor starter of standard make such as MEI /Kilburn/ Jyoti/ Siemens /Larson & Tubro conforming to IS-60947-4-1 latest with up to date ammendments for squirrel cage/slip-ring motor (make to be specified by the tenderers) mounted on panel board with magnetic type over load release & dashpot,time lag,under voltage release with initial oil filling . |
| 419 | Note:- Star - delta - starter upto 37.5 KW , ATS between 37.5 KW to 50 KW and stater rotor starter with slipring motor beyond 50 KW. |
| 420 | Providing M.S. sheet 16 SWG steel fabricated floor mounted closed almirah type switch board including angle iron post of suitable height and size ISA 40x40x6mm duly painted comprising and capable of mounting including providing and fixing in position the following accessories with all internal electric connections. The drawing of panel board shall be subject to approval of Engineer in charge.Conforming to IS 61439-1&2 or latest edition |
| 421 | a). Ammeter AC supply,100 mm dia circular dial Auto electric/AE/IMP/Havells make of suitable range for above motor with selector switches conforming to BIS 1248-(P-II)1983 and IS:61869-2 latest with up to date ammendments. |
| 422 | b). Voltmeter AC supply,100 mm dia circular dial Auto electric/AE/IMP/Havells make of suitable range for above motor with selector switches conforming to IS 60947-3 as per IS 1248 or IS 61010-1 with up to date ammendments. |
| 423 | c).TPN switches SDF with HRC fuses of Kilburn/Larsen & Tubro/Standard/ Siemen/ Havells make and having capacity 30% extra of the operational rating of motor as per IS 60947-3 with upto date ammendments immediatly after the power meter of HPSEB. |
| 424 | d).Busbar chamber having three copper bars of suitable rating for full length equal to width of board of three live phases and one copper bar of half rating of full length for neutral conforming to IS 61439-2 and IS 1897 read with IS 60445 all latest with upto date ammendments. |
| 425 | e).ACB/ MCB/ Oil circuit breaker of suitable capacity of Kilburn/ L &T/ MEI/ GEC/ Standard make on incomming feeder for motors offered by the tenderer conforming to IS 60947-2 latest with upto date ammendments with initial oil filling whenever required & neutral linked under voltage release. |
| 426 | f).Three phase indicating lamps complete with toggle switches for individual motors conforming to IS 60947-5-1 latest with up to date ammendments. |
| 427 | g) Earth leakage circuit breaker/ relay of recommended make such as Kilburn / L&T/ MET/ GEC conforming to IS-60947-2 with upto date ammendments and of suitaible range which should have control box, oprating handel and trip/reset push button, on/ off indicators, re-indicating off spring condition of the circut breaker for over current protection. The circuit should be equipped with magnet thermal release with metallic tap CTS. It should also be fitted earth fault for tripping of breaker on occurance of earth fault on/ of breaker load side. |
| 428 | h).Hour run meter of reputed make of four digit capacity conforming to IS- 60947-5-1 (latest edition)/recommendations. |
| 429 | i).Suitable three phase voltage monitor relay with all protections & usual indicators with electric sirens against single phasing, low voltage, high voltage & overloading & phase voltage difference as per IS-60255-1 with up to date ammendments. |
| 430 | k).Single phase preventor of reputed make & suitable capacity conforming to IS:60947-5-1 read with IS 60947-8 with up to date ammendments |
| 431 | supply of Kirloskar/ Kilburn/ IVC/ Fouress/ Gled/ BHEL/ Leader/ Bir/ Kartar/ Pelicon make of cast iron/cast steel double flanged sluice valve having size one size higher than the nominal delivery size of pump and capable of withstanding nominal seat pressure as mentionmed in item No. 1(a) + surge pressure conforming to BIS/API-standard with up to date ammendments for delivery line of pump. The class of valve shall be ASA-300 conforming to API 600 specification. |
| 432 | Supply of Kirloskar/ Kilburn/ IVC/ Fouress/Gled/ BHEL/ Leader/ Bir/ Kartar/ Pelicon make of suitable size cast iron/cast steel double flanged swing check type reflux valve for delivery line of pump having bye pass arrangement & size one size higher than the nominal delivery size of pump and capable of withstanding nominal seat pressure as mentionmed in item No. 1(a) + surge pressure and conforming to BIS/API-standards with up to date ammendments for delivery line of pump. The class of valve shall be ASA-300 confirming to API-6D |
| 433 | a).Providing,laying,jointing & testing at site suitable size copper PVC insulated armoured power three & half core cable ( from meter of HPSEBL TO CIRCUIT BREAKER) conforming to IS 7098 or latest with up to date ammendments of Siemen/Gloster/ICC/ EICO/National /IEC make from meter of HPSEB to circuite breaker & from circuit breaker to bus bar switch & starter (one cable carrying all three phases) including all other electrical equipment/accessories such as thimbles,flexible pipe,solder, nuts & bolts,cable glands etc. laid in pipes or trenches under floor The type,size & make will be subject to approval of HPSEB authorities. In case of non acceptance by HPSEB authorities it shall have to be replaced by the tenderer free of cost. (30 Rmt.). The size of cable shall be 16 mm2 . |
| 434 | b).Providing,laying,jointing & testing at site PVC jointless flat water proof cable ( for Motor Side ) as per IS 7098-1 (latest with up to date ammendments) suitable for the pump sets offered from circuite breaker to motor & motor to starter including all other electrical equipments such as thimbles, flexible pipes, solder,nuts & bolts,cable glands etc. laid in pipes or trenches. The type,size & make will be subject to approval of HPSEB authorities.In case of non acceptance by HPSEB authorities it shall have to be replaced by the tenderer free of cost. (2x60 = 120 Rmt.) The size of cable shall be 10 mm2 . |
| 435 | Providing & laying at site double loop earthing with copper plate 600x600x3mm thick electrode complete with material such as charcoal, common salt ,GI pipes, thimbles, nuts & bolts,digging of pits,GI wiring & 25x5mm copper strips of required capacity conforming to BIS 3043-12018 latest with up to date ammendments suitable for above motors & other electrical equipments i/c cost of carriage of material in all leads & lifts & as directed by the Engineer-in-charge. |
| 436 | Supplying and fixing of 100 mm dia circular dial pressure gauge of suitable range & standard make such as Fiebeg/Bourden/ Precision/PREGA with all accessories such as stop cock,copper tubing etc.conforming to BIS 3624-2018 or latest with up to date ammendments. |
| 437 | Providing and lowering in position at site of GMS pipe (MG) column pipe assembly of size as indicated in item no.1d including MS flanges of table-17 capable to withstanding nominal pressure as mentioned in item no.1a & conforming to IS:6392-1971 with upto date ammendments including the cost of rubber/asbestos gasket of maximum 3 mm thickness as per IS: 2712-1979 and required numbers of nuts and bolts as per IS: 1364-1983. The column pipe should be provided & lowered as per the direction of Engineer-in-charge. The same shall be of suitable thickness,grade & specification capable of withstanding minimum 1.5 times the total presure as indicated in item no 1 a.unless otherwise specified properly jointed at every three mtrs including all necessary acessories like increaser/reducer,flanges,tees,bends etc.including supporting clamps (2 nos) at the top of assembly and i/c cost of jointing of column pipe with Rising main with additional length of delivery pipe of approximately 10 m as per the direction of Engineer-in-Charge ( 55+10 = 65 mtrs.). |
| 438 | Supply & errection of floor/wall mounted power factor shunt capacitor conforming to IS 1334 and IS 1341 or latest with upto date ammendments of BHEL/GEC/Machneil/ Mager/Bajaj/L&T make to raise the prevailing power factor at site to 0.95 for direct connection to induction motor individually,of required KVAR according to HP of motor offered including cable Siemens/Gloster/ICC make from busbar chamber to capacitor & also including L&T//Kilburn/Standard/Siemen/Havells make ICTP switches conforming to IS 60947-3 or latest with HRC fuses (Range to be specified by the tenderer) 5 KVAR capacity.i/c cost of carriage of material in all leads & lifts & as directed by the Engineer-in-charge.i/c cost of carriage of material in all leads & lifts & as directed by the Engineer-in-charge. |
| 439 | Centrifugal Pump set for LIS Kundlu:- Supply, erection, testing & commissioning of horizontal spindle,horizontal split casing,radial split Single,/Multistages centrifugal pumps of standarad make such as KSB/ Mather & Platt/ Jyoti / Kirloskar/ Beaconweir /BS & BE conforming to BIS 6595-2018 -Part-2 or latest with upto date 9137 ammendments read with BIS 6595-2018 Part-1 or latest edition to handle clear raw water having charters tics as mentioned in item 1 (a) as under, with impelleres,casing ring, priming funnels & shaft sleeves of bronze, shaft of steel with cast iron casing of suitable capacity coupled directly through a flexible coupling on a common base plate of cast steel /Mild steel to BHEL /Kirlokar/ NGEF/ Crompton / Siemen/Jyoti /GEC make slip ring /squirrel cage screen protected drip proof energy efficient three phase induction electric motor having minimum energy efficiency level IE-2 suitable for operation on the data given below. i/c the cost of all accessories in all lead & lifts & carriage of material at site as per direction of Engineer-In-Charge. |
| 440 | Total Head in mtrs (i/c depth of Column Pipe in case of t/well) :267.12 m |
| 441 | Capacity (in LPS) of each pump set. 6.11 |
| 442 | Dia of R/Main (in mm)100 mm |
| 443 | Length of R/Main. 2450 mtrs |
| 444 | SITE CONDITIONS:- |
| 445 | Location of Site:- Kundlu Khad near Shamshanghat |
| 446 | The altitude of place in which the motor is intended to work:- 567.00 mtrs |
| 447 | Humidity:- Wheather generally remains humid during monsoon season |
| 448 | Nature of atmosphere:- As normally encountered in Shivalik Ranges |
| 449 | Detail of quality of water :- Clear cold water |
| 450 | Water free from sand or not:- Yes |
| 451 | Water corosive or not:- Not |
| 452 | Turbidity :- upto50 ppm |
| 453 | NPSH available :-Positive suction. |
| 454 | Any other information or requirement:- ----- |
| 455 | OPERATING CONDITIONS:- |
| 456 | Type of current:- AC three/single phase |
| 457 | Operating frequency:- 50HZ |
| 458 | Rated voltage:- 400 (+/-) 10% volts |
| 459 | System of earthing if any to to be adopted:- Double loop earthing as per BIS 3043-1987 latest with upto date ammendments |
| 460 | Speed of revolution:- To be quoted by tenderer |
| 461 | Direction of rotation:- To be quoted by tenderer |
| 462 | No. of working hours per day:- 20.00 Hours |
| 463 | The max. Temp. of cooling air & water in the place in which the pumpset is intented to work in ordinary service:- 35 degree centigrade |
| 464 | MOTOR:- |
| 465 | Ref to BIS code:- BIS 12615-2011 read with BIS 900-1992 (latest)with upto date ammendments with minimum efficiency IE level-2 |
| 466 | Type of enclosure of motor:- SPDP(as per BIS 4691-1985 (latest) |
| 467 | Type of duty:- Continuous duty type as per IS-12824-1989 or latest with up to date ammendments |
| 468 | Mechanical out put in KW:- Suitable for driving centrifugal pumps required for duties specified against pumps.To avoid overloading of motor a margin of about 15-20% may be kept in the rated out put of prime mover. |
| 469 | Class of insulation:- Class ~B~ |
| 470 | Max.permissible temp. rise of motor reqd. if different from that given in B (viii) above:- 35 degree centigrade |
| 471 | Particulars of test reqd. & where they are to be conducted:-. As per terms & conditions attached |
| 472 | Particulars as to whether voltage limiting device will be employed:- ATS/star delta starter,oil immersed,fully automatic to be installed between bus bar & motor Shunt capacitor is also proposed to be installed for improving the power factor at site. |
| 473 | (NOTE:- Star delta starter upto 37.5 KW, ATS between 37.5 KW to 50 KW & Stator rotor starter beyond 50 KW) |
| 474 | Motor whether squirrel cage or slipring:- (Note:- Squirrel cage upto 65HP and slipring above 65HP) Squirrel cage/slip-ring |
| 475 | Details of shaft extension reqd.:- Just sufficient to provide direct drive by flexible coupling to pump. |
| 476 | Type of slip-ring gear whether continouly rated or for starting purposes only & whether to be fitted with brush lifting or short circuit arrangements or both if interlocks are rquired.:- Continouslly rated for Squirrel cage/ Slipring motor |
| 477 | Breakway torque in terms of rated load torque & the corresponding breakway starting current which may be taken from the supply with the starting apparatus in circuit:- Breakway torque to be given by the tenderer but the starting current should not exceed 2.5 times of the full load current. |
| 478 | Nature of load & any information regarding the driven machine which has a bearing upon the torque reqd. during the accelerated period, the kinetic energy of the moving parts to be accelrated & No.of starts during a specified period:- Sufficient to work the pump offered |
| 479 | Where possible fault capacity of the system to which the motor is connected.:- The motor should be able to withstand initial current of 2.5 times the rated current for two minutes without suffering damages or permanent deformations |
| 480 | PUMPS:- BIS 6595-2018 read with 9137-1978 both with upto date ammendments. |
| 481 | Nos of pumps reqd.:- 1 No Pump |
| 482 | Spare parts required:- For two years normal maintenance as recommended by manufacturer. |
| 483 | Optional fittings reqd.:- Air cock for exahausting air from each stage. |
| 484 | PUMP OPERATING CONDITIONS:- |
| 485 | Capacity of each pump (in lps) :- 6.11 Lps |
| 486 | Total head (in Mts.) :- 267.12 |
| 487 | If total head is not known then following details be provided:- |
| 488 | i) Static head (in mtrs):- |
| 489 | ii) Minimum depth of water (in mtrs) :- |
| 490 | iii) Seasonal Variation in water level (in mtrs):- |
| 491 | iv) Ground level to max. water level (in mtrs) :- |
| 492 | v) Ground level to delivery point (in mtrs):- |
| 493 | vi) Pressure in the suction tank (in kg/cm^2)- |
| 494 | vii) Pressure in the delivery tank (in kg/cm^2) :- |
| 495 | Length of R/Main (in mtrs):- 2450 Rmt |
| 496 | Dia of R/Main (in mm):- 100 mm |
| 497 | Drive arrangement:- Direct through flexible coupling on a common base plate |
| 498 | Drive type:- Electric driven |
| 499 | NPSH reqd.:- To be quoted by the tenderer |
| 500 | Limits of total head in which the pump is reqd. to operate:- (-) 15% to (+) 10% of total head. |
| 501 | Suction/delivery size of pump:- To be specified by the tenderer |
| 502 | Efficiency of pump at To be specified by the tenderer |
| 503 | a) duty head 267.12 mtrs |
| 504 | b) (+) 10 % head 293.83 mtrs |
| 505 | c) (-) 15 % head 227.05 mtrs |
| 506 | Material of construction:- To be specified by the tenderer (manufacturers certficate to be appended) |
| 507 | Supplying and installation of suitable direct on line/ oil immersed star delta/ ATS/ stator rotor starter of standard make such as MEI /Kilburn/ Jyoti/ Siemens /Larson & Tubro conforming to IS-60947-1 latest with up to date ammendments for squirrel cage/slip-ring motor (make to be specified by the tenderers) mounted on panel board with magnetic type over load release & dashpot,time lag,under voltage release with initial oil filling . |
| 508 | Note:- Star - delta - starter upto 37.5 KW , ATS between 37.5 KW to 50 KW and stater rotor starter with slipring motor beyond 50 KW. |
| 509 | Providing M.S. sheet 16 SWG steel fabricated floor mounted closed almirah type switch board including angle iron post of suitable height and size ISA 40x40x6mm duly painted comprising and capable of mounting including providing and fixing in position the following accessories with all internal electric connections. The drawing of panel board shall be subject to approval of Engineer in charge.conforming to IS 61439-1&2 or latest ammendments. |
| 510 | a). Ammeter AC supply,100 mm dia circular dial Auto electric/AE/IMP/Havells make of suitable range for above motor with selector switches conforming to BIS 1248-(P-II)2013 or 61010-1 latest with up to date ammendments. |
| 511 | b). Voltmeter AC supply,100 mm dia circular dial Auto electric/AE/IMP/Havells make of suitable range for above motor with selector switches conforming to BIS 1248-2013 or 61010-1 with up to date ammendments. |
| 512 | c).NTP switches with HRC fuses of Kilburn/Larsen & Tubro/Standard/Siemen/Havells make and having capacity 30% extra of the operational rating of motor as per IS 60947-3 with upto date ammendments immediatly after the power meter of HPSEBL. |
| 513 | d).Busbar chamber having three copper bars of suitable rating for full length equal to width of board of three live phases and one copper bar of half rating of full length for neutral conforming to IS 61439-2 and read with IS- 60445 all latest with upto date ammendments. |
| 514 | e).ACB/ MCB/ Oil circuit breaker of suitable capacity of SEIMEN / Sehnieda/ABF Standard make on incomming feeder for motors offered by the tenderer conforming to IS 60987-2 latest with upto date ammendments with initial oil filling whenever required & neutral linked under voltage release. |
| 515 | f).Three phase LED ( Red,yellow, blue) indicating lamps complete with toggle switches for individual motors conforming to IS 60947-5-1 latest with up to date ammendments. |
| 516 | g) Earth leakage circuit breaker/ relay of recommended make such as Kilburn / L&T/ MET/ GEC conforming to BIS-12640-2 with upto date ammendments and of suitaible range which should have control box, oprating handel and trip/reset push button, on/ off indicators, re-indicating off spring condition of the circut breaker for over current protection. The circuit should be equipped with magnet thermal release with metallic tap CTS. It should also be fitted earth fault for tripping of breaker on occurance of earth fault on/ of breaker load side. conforming to IS 60947-2 and IS 12640(Part-2) |
| 517 | h).Hour run meter of reputed make of four digit capacity conforming to IS-1248-P-1722 (latest edition)/recommendations.of approved make. |
| 518 | i).Suitable three phase voltage monitor relay with all protections & usual indicators with electric sirens against single phasing, low voltage, high voltage & overloading & phase voltage difference as per IS-60255-1 with up to date ammendments. |
| 519 | k).Single phase preventor of reputed make & suitable capacity conforming to IS:60947-1&8 with up to date ammendments |
| 520 | Supply of Kirloskar/ Kilburn/ IVC/ Fouress/ Gled/ BHEL/ Leader/ Bir/ Kartar/ Pelicon make of cast iron/cast steel double flanged sluice valve having size one size higher than the nominal delivery size of pump and capable of withstanding nominal seat pressure as mentionmed in item No. 1(a) + surge pressure or 1.5 times sustained operating pressure whichever is more conforming to API-standards with up to date ammendments for delivery line of pump. The class of valve shall be ASA-300 conforming to API-600 specifications |
| 521 | Supply of Kirloskar/Kilburn/IVC/Fouress/Gled/BHEL/Leader/Bir/Kartar/Pelicon make of suitable size cast iron/cast steel double flanged swing check type reflux valve for delivery line of pump having bye pass arrangement & size one size higher than the nominal delivery size of pump and capable of withstanding nominal seat pressure as mentionmed in item No. 1(a) + surge pressureor 1.5 times sustained operating pressure whichever is more conforming to API-standards with up to date ammendments for delivery line of pump. The class of valve shall be ASA-300 conforming to API-6D specifications |
| 522 | Supply of Kirloskar/ Kilburn/IVC/ Fouress/ Gled/ BHEL/ Leader Bir/ Kartar/ Pelicon make of suitable size cast iron /Cast Steel double flanged swing check type reflux valve having bye pass arrangement & size equal to dia of R/main as mentioned in item No.1 (c) for withstanding nominal seat pressure as per item No.1(a) + surge pressure or 1.5 times sustained operating pressure whichever is more conforming to API-standards with up to date ammendments for delivery line of pump. The class of valve shall be ASA-300 conforming to API-6D specifications |
| 523 | Providing, laying,jointing & testing at site suitable size copper PVC insulated armoured power three & half core cable conforming to BIS 1554 (Part I) -1988 or latest with up to date ammendments of Siemen/Gloster/ ICC/EICO /National /IEC make from meter of HPSEBL to circuit breaker & from circuit breaker to bus bar switch & starter (one cable carrying all three phases) including all other electrical equipment/accessories such as thimbles,flexible pipe,solder,nuts & bolts,cable glands etc. laid in pipes or trenches under floor. The type,size & make will be subject to approval of HPSEBL authorities. In case of non acceptance by HPSEBL authorities it shall have to be replaced by the tenderer free of cost i/c cost of carriage of material in all leads & lifts & as directed by the Engineer-in-charge. The size of cable shall be 35 mm square. |
| 524 | Providing, laying, jointing & testing at site suitable size copper PVC insulated armoured power three core cable conforming to BIS 1554 (part I)-1988 or latest with up to date ammendments of Siemen/ Gloster /ICC/ EICO/National / IEC make from switch to starter & starter to motor (one cable carrying all three phases) including all other electrical equipment /accesories such as thimbles,flexible pipes, solder,nuts & bolts,cable glands etc. laid in pipes or trenches under floor.The type,size & make will be subject to approval of HPSEBL authorities. In case of non acceptance by HPSEBL authorities it shall have to be replaced by the tenderer free of cost i/c cost of carriage of material in all leads & lifts & as directed by the Engineer-in-charge. The size of cable shall be 25 mm square. |
| 525 | Providing & laying at site double loop earthing with copper plate 600x600x3mm thick electrode complete with material such as charcoal, common salt ,GI pipes,thimbles,nuts & bolts,digging of pits,GI wiring & 25x5mm copper strips of required capacity conforming to BIS 3043-1987 latest with up to date ammendments suitable for above motors & other electrical equipments i/c cost of carriage of material in all leads & lifts & as directed by the Engineer-in-charge. |
| 526 | Supply & errection of floor/wall mounted power factor shunt capacitor conforming to BIS 2834-1986 or latest with upto date ammendments of BHEL/GEC/Machneil/ Mager/Bajaj/L&T make to raise the prevailing power factor at site to 0.95 for direct connection to induction motor individually,of required KVAR according to HP of motor offered including cable Siemens/ Gloster/ ICC make from busbar chamber to capacitor & also including L&T// Kilburn/Standard/Siemen/Havells make ICTP switches conforming to BIS 4064-1978 or latest with HRC fuses (Range to be specified by the tenderer) i/c cost of carriage of material in all leads & lifts & as directed by the Engineer-in-charge.i/c cost of carriage of material in all leads & lifts & as directed by the Engineer-in-charge. The capacity of shunt capactor is 11 KVAR. |
| 527 | Supply of 100 mm dia circular dial pressure gauge of suitable range & standard make such as Fiebeg/Bourden/ Precision/PREGA with all accessories such as stop cock,copper tubing etc. conforming to BIS 3624-1987 or latest with up to date ammendments. |
| 528 | NOTE:- Actual laying to be done as per final drawings to be approved by the Engineer in charge |
| 529 | Providing and fixing double flanged suction,delivery pipe of GMS pipe(M) grade considering site requirements, NPSH required & available & flanges,rubber gaskets 3mm thick as per BIS 2712-1978 nuts bolts as per BIS 1364-1983 and special upto 5 mtrs awayfrom the outer wall of pump house as per lay out drawings approved by Engineer-in-charge.The pipe shall be capable of withstanding minimum 1.5 times the total pressure as indicated in item no.1 a or total dynamic pressure (+) surge pressure which ever is more.The size of suction pipe shall be one or two sizes larger than the suction size of pump such that velocity of flow in suction pipe is not more than 1.50 mtr.sec. & delivery pipe shall be of size one size larger than nominal delivery size of pump i/c cost of jointing delivery pipes and common header with Rising main complete in all respect. |
| 530 | Wiring for light/Fan point/Exhaust fan point/call bell point with 1.5 Sq.mm PVC insulated heat resident flame retardant (HRFR)of low smoke single core (flexible) copper conductor cable in PVC casing and capping and earthing the light point with 1.5 sq.mm HRFRLS /PVC insulated single Group \\"C\\" as required including carriage of all material within all leads and lifts. |
| 531 | Wiring for light/power plug with 2 x 4 Sq.mm PVC insulated heat resistant flame retardant (HRFR)and low smoke single core (flexible ) copper conductor cable in PVC casing and capping along with 1 no, 4sq. mm HRFRLS / PVC insulated single core copper as required including carriage of materials within all leads and lifts. |
| 532 | Wiring for light/power plug with 4 x 4 Sq.mm PVC insulated heat resistant flame retardant (HRFR)and low smoke single core (flexible ) copper conductor cable in PVC casing and capping along with 2no, 4sq. mm HRFRLS / PVC insulated single core copper as required including carriage of materials within all leads and lifts. |
| 533 | Wiring for light/power plug with 2 x 1.5 Sq.mm PVC insulated heat resistant flame retardant (HRFR)and low smoke single core (flexible ) copper conductor cable in PVC casing and capping along with 1 no, 4sq. mm HRFRLS / PVC insulated single core copper conductor cable as required including carriage of materials within all leads and lifts. |
| 534 | Wiring for circuit / sub main wiring with 4 x 1.5 Sq.mm PVC insulated heat resistant flame retardant (HRFR)and low smoke single core (flexible ) copper conductor cable in PVC Casing & capping along with 2 no, 2.5sq. mm(4x2.5+2x2.5) HRFRLS/PVC insulated single core copper conductor cable as required including carriage of materials within all leads and lifts. |
| 535 | Supplying and fixing metal box of 100 x 100 x 60mm deep (Nominal size) on surface/recess with suitable size phenolic laminated sheet cover fixing 3 pin 15/16 amps socket tumber/piano type switch connections painting etc. including carriage of materials within all leads and lifts |
| 536 | S/F of 6amps to 32 amps rating 10 KA breaking capacity ,240 Volts, \\"C\\" curves miniature circuit breaker of following poles in the existing MCB DB complete with connections testing and commissioning etc. as required including carriage of materials within all leads and lifts Category -A single pole. |
| 537 | Supplying and fixing 40 Amps/50 amps / 63 Amps rating 10 KA breaking capacity 240 Volts \\"C\\" curves miniature circuit breaker of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required including carriage of material within all leads and lifts. Double pole Category- B 63 Amps. |
| 538 | Supplying and fixing of following way single pole and neutral sheet steel MCB distribution board 240 volts, on surface/recessed complete with tinned, copper busher neutral link, earth bar, din bar, detachable gland plate, interconnections, including painting, earthing etc. as required : bus bar 8 way. |
| 539 | Providing, installing, testing and commissioning of 2x36 watt -CFL surface mounting (category \\"A\\" including wiring with 1.5 Sq mm PVC insulated copper conductor single core cable etc.as required . |
| 540 | Providing, installing, testing and commissioning of ceiling fan and regulator including wiring the rod of standard length (upto 30 cm) with 1.5 Sq mm PVC insulated copper conductor single core cable etc.as required 1200 mm sweep Category A. |
| 541 | Providing, installing, testing and commissioning of 1x36 watt -FTL (T8) shock proof slim (category \\"A\\" including wiring with 1.5 Sq mm PVC insulated copper conductor single core cable etc.as required . Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 04, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 14, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 4 daysAug 14, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 4 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender