Tender For Provn Of Toilet And Bathroom Block For Per Line Area Alongwith Provn Of Lt Ug Cable And Allied Work At Jaipur Mil Stn
Tender Value
Ref. Documents
Estimated cost
Bid Submission
25 Aug 2026
1 days left
EMD
28720
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jaipur → Rajasthan
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Provn Of Toilet And Bathroom Block For Per Line Area Alongwith Provn Of Lt Ug Cable And Allied Work At Jaipur Mil Stn
BOQ
| Sl. No. | Item Description |
| 1 | Excavation in trenches n.exc 1.5 m wide and n.exc 1.5 m in depth, for foundation etc or for shafts, wells, manholes, pier holes, laying of cables etc n.exc 10 Sqm on plan and n.exc 1.5 m in depth and getting out in soft / loose soil complete all as specified and directed. |
| 2 | M&L PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and directed. |
| 3 | M&L pre-cast cement concrete 1:3:6, type C1 (using 20mm graded stone aggregate) block masonry with solid blocks, exc 10 cm in width and setting in cement mortar 1:6 complete all as specified and directed. |
| 4 | M&L for brick work with sub-class 'B' bricks (using old size bricks ), straight or curved on plan exc 6m mean radius built in In cement mortar 1:6 complete all as specified and directed |
| 5 | M & L for 40mm thick PCC 1:2:4 type B0 (using 12.5mm graded stone aggregate) Damp proof course to horizontal or vertical surfaces including necessary formwork and finishing the surface even and smooth complete all as specified and directed |
| 6 | Removing excavated material to a distance exc 250 m but not exc 500 m and deposited where directed at a level n exc 1.5 m above the starting point complete all as specified and as directed. |
| 7 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft / loose soil complete all as specified and as directed. |
| 8 | M&L Mild steel TMT bar 10 mm dia & over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9 mm dia or securing with clips complete all as directed and specified. |
| 9 | ,--- ditto--- all as per srl item No. 8 above but TMT bar of 5mm dia and over upto and including 10mm dia as in stirrups, spacers and binders complete all as directed and specified. |
| 10 | M & L for RCC M-25 (Design Mix) (using 20mm graded stone aggregate) as in Foundations, including rafts, footings, foundation beams, plinth beams, bases for columns etc, basement slabs, under reamed piles and mass concrete complete all as specified and as directedNote : Reinforcement & formwork shall be measured and paid for separately. |
| 11 | M&L for RCC M-25 (design mix) (using 20 mm graded stone aggregate) as in Columns, pillars, piers, posts and struts complete all as specified and as directed.Note : Reinforcement & formwork shall be measured and paid for separately. |
| 12 | S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. |
| 13 | S & F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube of 1.25 mm thickness suppling & fixing in opening as per specification & drawing given in SSR Part-I complete all as directed and specified. |
| 14 | S & F 100mm butt hinges medium weight cold rolled mild steel and fixed complete as directed and specified. |
| 15 | S & F 100mm long handles, extruded aluminium alloy, fabricated type anodised complete all as specified and directed. |
| 16 | S&F 200 mm long aluminium anodised barrel tower bolt extruded section and fixed complete all as specified and directed. |
| 17 | S&F Factory made 35 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides covered with decorative face veneer with lipping/frame to match on both side complete all as specified and as directed |
| 18 | S&F in repair 300mm length aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed. |
| 19 | M&L for hard core of gauge n.exe 63 mm of broken stone or boulders, deposited spread and leveled in layers n exe 15cm thick watered and rammed to a true surface complete all as speciifed and directed. |
| 20 | M&L for 100mm thick plain cement concrete 1:4:8, type D-2 (using 40mm graded stone aggregate) as in sub base of floor complete all as specified and directed. |
| 21 | M&L for 25mm thick PCC 1:2:4, type B-0 (using 12.5mm graded stone aggregate) as in flooring and all other similar works finished even and fair complete all as specified and directed. |
| 22 | M&L for coloured jointfree non skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile 0.06 sqm but not exceeding 0.11 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed |
| 23 | M&L for coloured glazed ceramic tiles 450mm X 350mm X 7 to 8mm thick on vertical surfaces of wall such as dado, skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over and including 10mm thick backing coat in CM 1:4 complete all as specified and directed |
| 24 | M&L rendering 15mm thick in CM 1:6 on stone masonry surfaces or on surface other than fair faces of brick masonary finished even and smooth without using extra cement complete all as specified and directed. |
| 25 | M&L for rendering 15mm thick in CM 1:4 on fair faces of brick masonry surfaces or concrete surface finished even and smooth without using extra cement complete all as specified and directed. |
| 26 | M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed. |
| 27 | M & L for preparing new plastered surfaces of wall etc and applying two coats of cement base paint in plain patterns over a coat of alkali resistant priming paint all as specified and as directed |
| 28 | S&F rolled mild steel sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors fixed with angle cleats or other connecting plates conforming to Fe410-W(Gde E-250) Quilaty A complete all as specified and directed. |
| 29 | S&F mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment and well finished edges conforming to Fe 410 -W (Gde- E- 250) quality- A complete all as specified and directed. |
| 30 | M&L for prearation of new or previously untreated steel and iron surface of any description, over 10cm in width and girth not otherwise described and applying two coat of synthetic enamel paint over one coat of red oxide (zinc chrome) primer complete all as specified and directed. |
| 31 | M & L for 75mm thick PCC 1:3:6, type C-2 (using 40 mm graded stone aggregate) as in plinth protection laid in slope in 1:30 in alternative bays not exceeding 3 mtr in length. Exposed surfaces finished even and smooth without using extra cement including raking out joints between panel to panel and panel to wall and plugging the same with bitumen mastic using bitumen and sand mixture in 1:3 complete all as specified and directed . |
| 32 | Supply and fixing factory made uPVC white colour fixed glazed window/ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. The unit rate quoted by contractor excludes cost of glass and includes all other connected accessoriesNote: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 33 | S&F tinted glass 4mm thick, ordinary quality and glazing with and incl silicon in square n exc 0.5 Sqm in each pane complete all as specified and as directed. |
| 34 | M&L pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of approved colour having tensile strength of 550Mpa as in roof covering / cladding to wall, fixed with self tapping screws /J hook, L-type crancked hook complete all as specified and directed |
| 35 | S&F Mild steel screw bolts (purpose made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 30cm long and dia of neck 12mm to 20 mm complete all as specified |
| 36 | S&F 500 Ltrs capacity rotational moulded polyethylene water storage tank, white, tripple layered (cylindrical vertical with closed top) hoisted and fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc complete all as specified in SSR Part I and directed. |
| 37 | S&F 20mm dia ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed complete all as specified and directed.Note : Minimum weight for 20 mm dia shall not be less than 210gms. |
| 38 | S&F 15 mm dia steel water tubing, galvanized, medium grade, with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed |
| 39 | S&F 25 mm dia steel water tubing, galvanized, medium grade, with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed |
| 40 | S&F 40 mm dia steel water tubing, galvanized, medium grade, with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed |
| 41 | S&F vitreous china wash hand basin white flat back of size 630 x 450 mm excluding taps, chain & plug and porcelene stopper but including brackets /fastners, 32mm dia brass chromium plated waste coupling with long screwed shanks and fly-nuts, 32mm dia PVC waste pipe, flange end bedded in red lead cement and other end fixed, cutting for and pinning in ends of brackets complete all as specified and directed. |
| 42 | S&F pillar taps 15mm bore swan neck cast coper alloy CP fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or for union complete all as specified and directed. |
| 43 | S & F vitreous china urinal, half stall type, white incl providing and fixing plugs, including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement with grating and union for discharge pipe including PVC waste pipe and CP waste coupling complete all as specified and directed. |
| 44 | S&F vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe), including plastic water closet seat, black, closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device and connection to drain (or out going pipe) and to flushing pipe etc. incl trap set in cement concrete complete all as specified and directed. |
| 45 | S & F vitreous china squatting pan, 'Orissa\\" pattern, size 580 mm X 440 mm white with ‘P’ or ‘S' trap, front or back inlet and integral foot rests, any pattern and including fixing bolt, connector to flush pipe, lime concrete bedding and making connections to flush pipe, connector to branch pipe and anti syphonage pipes etc. including sealing the joints and making leak proof using sealant complete all as specified and as directed. |
| 46 | S&F PVC valveless, syphonic action type flushing cistern, low level, 10 ltr capacity, white, with intel, ball valve, float and handle including brakects, 32 mm dia polyethylene of low or high density or PVC flushing pipe and connections to pipes and fixing of chain and pull, or lever, if any complete all as specified & as directed. |
| 47 | S&F soap dish, stainless steel, approx size 160x160x90 mm fixed with chromium plated brass screws complete all as specified and as directed. |
| 48 | S&F tubular towel rail, brass chromium plated, 20mm dia, D type, 60cm long between flanges complete all as specified and as directed. |
| 49 | S&F 15mm bore angle stop valves, cast copper alloy, fancy type, chromium plated, screwed down high pressure with crutch or butterfly handle screwed for iron pipes or for unions and fixed complete all as specified and directed. |
| 50 | S&F PVC Connections 15mm size, 450mm long with PTMT nuts complete all as specified and as directed. |
| 51 | S&F 15 mm bore bib tap, fancy type, chromium plated cast copper alloy with cruth or butter fly handle, long body, screwed down, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed. |
| 52 | S & F 110mm bore PVC (SWR) WC connector with lip ring complete all as specified and as directed. |
| 53 | S&F PVC (SWR) floor trap, plain including jointing with solvent cement |
| 54 | S&F 20mm bore gun metal gate valve, screwed down high pressure with iron wheel head screwed both ends for iron pipe or for union complete all as specified and directed. |
| 55 | S& F PVC (SWR) gully traps of size 125/110 setting and jointing with solvent cement complete all as specified and directed. |
| 56 | S&F 110 mm bore UPVC (SWR) drainage pipes (type B conforming to IS-13592) single socketed in any length with rubber ring joints fixed to wallls with suitable size clamp complete all as specified & directed. |
| 57 | S&F 75 mm bore UPVC (SWR) drainage pipes (type B conforming to IS-13592) single socketed in any length with rubber ring joints fixed to wallls with suitable size clamp complete all as specified & directed. |
| 58 | S&F 110 mm dia PVC (SWR) bends, tee, socket etc any radius complete all as specified and directed. |
| 59 | S&F 75 mm dia PVC (SWR) bends, tee, socket etc any radius complete all as specified and directed. |
| 60 | S & F SS Grating doom 75 mm dia with or without waste hole including fixing in CM 1:4 complete all as specified and directed. |
| 61 | Supply, laying, jointing and testing of 150mm bore, DWC pipe (Double wall corrugated) of class SN-4 for sewer line, as per IS-16098 (Part –II), laid in trenches and jointed complete including all necessary fittings i.e. coupler, bend, Tee, reducer etc incl demolition and breaking up complete all as specified & directed .Note : Earth work shall be measured and paid seperately |
| 62 | M&L for point wiring with 1100 volts grade PVC insulated, unseathed, FRLSH multistranded copper conductor cable (conforming to (IS:694 /1990), single core, 1.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 sqmm (Green) drawn into and including concealed rigid non matalic PVC conduit medium grade size not less then 20mm dia ISI marked with all conduit fittings/fixing accessories and 1.6mm thick cadium plate sunken box covered with and including 3mm thick phenolic laminated white sheet cover for mounting switches, sockets, fan regulators etc for one light/fan/exhaust fan point controlled by one, one way switch 6 Amp and making good the disturbed portion as per existing complete all as specified and directed. |
| 63 | ,---ditto--- all as per item No. 62 above but for one 3 pin 5 Amp socket outlet controlled by one switch on same board with other switches complete all as specified and directed. |
| 64 | ,---ditto--- all as per item No. 62 above but for one 3 pin 5 Amp socket outlet controlled by one switch on independent board with other switches complete all as specified and directed. |
| 65 | ,---ditto--- all as per item No. 62 above but wiring with cable of size 2.5 Sqmm for one 5 pin 15 Amps socket out let on independent board and multistrand insulated copper earth continuity conductor of size 2.5 sqmm all as specified and directed by Engr-in-Charge. |
| 66 | S&F switch piano flush button single pole one way 6 Amp complete all as specified and directed. |
| 67 | S&F switch piano flush button single pole one way 16 Amp complete complete all as specified and directed. |
| 68 | S&F socket outlet, 2-in-1, 3 pin 6 Amps flush type compete complete all as specified and directed. |
| 69 | S&F socket outlet, 2-in-1, 3 pin 6 & 16 Amps combined flush type compete complete all as specified and directed. |
| 70 | S&F ceiling rose PVC polycarbonate isolated body, 3 terminals 230 Volt complete all as specified and directed. |
| 71 | S&F LED batten (1.2M) made of CRCA sheet housing with a PC glossy diffuser duly prewired connection having a nominal system lumen output of 2000 lumens at a minimum system efficiency of 105 lumen per watt and total power consumption not more than 20 watt including driver. It has a rated system life time of 40000 burning hours at L70 and should have a colour temperature of 6500K, CRI>80, THD<10% and PF>0.95 complete all as specified and directed. Make - Philips Cat part BN308C LED20S-6500 L120 PSU WH, Crompton Cat part CIS-305-40-57-SL-DP-NWH, Havells Cat no STOUTPLUS600BS20WLED840SPCWH. |
| 72 | S&F LED batten (0.6m) made of CRCA sheet housing with a PC glossy diffuser duly prewired connection having a nominal system lumen output of 900 lumens at a minimum system efficiency of 115 lumen per watt and total power consumption not more than 10 watt including driver. It has a rated system life time of 40000 burning hours at L70 and should have a colour temperature of 6500K, CRI>80, THD<10% and PF>0.95 complete all as specified and directed. |
| 73 | S&F LED lamp 12watt having a nominal system lumen output of 1200lumens at a minimum system efficency of 100 lumens per watt having colour temperature o 6500K of approved make complete all as specified and directed. |
| 74 | S&F LED bulk head light fitting 9 watt IP 66 & IK 09 with with pressure die cast aluminium housing & polycarbonate diffuser duly prewired connection with 0.75sqmm PVC insulated & sheathed three core flexible multi stranded copper conductor cable complete all as specified & directed. |
| 75 | S&F greenline high efficiency LED light luminaire 25 watt complete with driver, pressure die cast aluminium housing, UV stablized polycarbonates cover, inbuilt power unit, IP-65 protection including mounting bracket made of 25mm GI pipe, medium grade ISI marked not less than 1.2m, bend in shape, fix with 02 no clamps, nut, bolt and washers as reqd and painting the bracket with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified & directed. |
| 76 | S&F angle holder, insulated polycarbonate body with back plate complete all as specified and directed. |
| 77 | S&F MCBs of 'B' curve single pole 6 to 32 Amps having breaking capacity 10 KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs complete all as specified and directed. |
| 78 | S&F MCBs of 'C' curve SPN 40-63Amps having breaking capacity 10 KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs complete all as specified and directed. |
| 79 | S&F flush mounting factory made MCBs Distribution board SPN, 8 ways, powder coated, CRCA steel sheet, degree of protection IP-43, IK-09 with reversible double door, 240V, recess mounted having insulated 200 amp tinned copper bus bar, neutral bus bar, earth bar, din bar, detachable gland plate, blanking plate in unused spaces as required, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs complete all as specified and directed. Note : MCCB, MCBs and MCB DB shall be of the same make. |
| 80 | S&F fresh air fan of sweep 250 mm, made of sturdy Engineering plastic with self closing louvers, 230V, 50 Hz, 1200 RPM, copper winding incl incl three core 0.75sqmm copper cable connection from ceiling rose to exhaust fan complete all as specified and directed. |
| 81 | M&L for earthing complete with galvanized steel earth plate electrode of size 60cmx60cmx6.0mm buried directly in ground, vertically to depth not less than 2.25mtr below normal ground level with top edge of the earth plate at depth not less than 1.5 metre below ground level surrounded from all sides with alternate layers of charcoal and common salt and connected to GI lead wire 4.0mm dia by means of GI bolts, nuts washers & check nuts electrode connected to main switch board or main control board or on poles or on transformer and GI pipe medium grade 20mm bore for watering, 40mm bore GI pipe medium grade for protection of GI wire upto test point including providing funnel and wire mesh GI frame and 10cm thick suitably reinforced RCC pit cover, PCC chamber pit with PCC (1:3:6) type C2 using 40mm graded stone aggregates complete including excavation and earth work in any type of strata, disposal of surplus soil to a distance not exceeding 50 mtr, all as specified ans shown in Electrical plate No. 3 of SSR Part-1, PCC pit shall be provided at least 50 cm away from the earth pit and not just on earth pit including testing on completion complete. (Note - GI lead wire size 4.0mm upto 7.5 m included in the item). |
| 82 | Supply, laying, jointing, testing & commissioning LT under ground cable XLPE insulated, screened PVC sheathed, galvanised steel strips or wire armoured, heavy duty electric cable with multi stranded aluminium conductor, 1100 volts grade cross sectional area 16sqmm, 4core confirming to IS:7098 (part-I), laid in trenches, ducts, pipes or fixed on poles or walls including all necessary clamps, nut, bolt, washers, saddle etc complete all as specfied and directed.Note : The cost of AI thimbles / lugs and cable gland etc is included in quoted raes. |
| 83 | M & L Sand cushioning to under ground cable with screened and washed sand (non cohessive), 8 cm before laying cable and 15cm after laying and punned to 18cm after laying of cable complete all as specified and directed by Engineer-in-Charge.Note : Punned thickness shall be considered for payment purpose. |
| 84 | Supply and laying factory made unreinforced pre-cast concrete cable protection cover LV class, type-I, flat of size 250mm X 150mm X 40mm laid across the cable (i.e. width of cover along the length of cable) for UG cable protection laid on the top of the sand cushioning complete all as specified and directed. Please Enable Macros to View BoQ information |
| 85 | Supply and laying factory made unreinforced pre-cast concrete cable protection cover LV class, type-I, flat of size 250mm X 150mm X 40mm laid across the cable (i.e. width of cover along the length of cable) for UG cable protection laid on the top of the sand cushioning complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 04, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 25, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 1 dayAug 27, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 3 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender