Tender For Certain Revenue Works Both B/R And E/M In Nature At Phase-I And Ii Under Ge Tenga
Tender Value
40.50 Lakhs
Estimated cost
Bid Submission
24 Aug 2026
20 days left
EMD
81000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
kameng → Arunachal Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Certain Revenue Works Both B/R And E/M In Nature At Phase-I And Ii Under Ge Tenga
BOQ
| Sl. No. | Item Description |
| 1 | Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in hard / dense soil complete all as specified and as directed. |
| 2 | Excavation in trenches n, exc 1.5 mtr wide and n, exc 1.5 mtr depth and getting out hard /dence soil, complete all as directed. |
| 3 | M & L for PCC 1:3:6 type C-2 (using 40mm graded stone aggregate) as in foundation filling or mass concrete, complete all as specified and directed. |
| 4 | M&L for reinforced cement concrete Type B1, 1:2:4 (Nominal Mix) using 20 mm graded aggregate as in foundation, including rafts, footings,foundation beams, base for columns etc, basement slabs, under-reamed piles and mass concrete complete, all as specified and directed. |
| 5 | M&L for reinforced cement concrete Type B1, 1:2:4 (Nominal Mix) using 20 mm graded aggregate as in columns, pillars, piers, posts and struts complete, all as specified and directed. |
| 6 | M&L for Reinforced cement concrete Type B1, 1:2:4 (Nominal Mix) (20 mm graded agreggate) slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like |
| 7 | M&L for Reinforced cement concrete Type B1, 1:2:4 (Nominal Mix) (20 mm graded agreggate) Beams, cantilevers, bressummers, lintels over 1.5m span |
| 8 | Use and waste of form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits(if any) in foundation, plinth beams and similar work vertical or to batter complete all as specified to give rough finished surfaces on flat surfaces of concrete. |
| 9 | Use and waste form work to sides of square or rectangular columns, pillars, posts and struts for rough finished surfaces of concrete complete. |
| 10 | Use and waste formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) |
| 11 | Use and waste Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. |
| 12 | M & L for Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips |
| 13 | All as per Serial Item No 12 above but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders. |
| 14 | M&L for brick work with fly ash bricks old Size bricks straight or curved on plan exc 6 mtr mean radius built in CM (1:6) all as spd and directed |
| 15 | M&L for rendering 5mm thick on fair faces of brick work or concrete surfaces in CM (1:3) in ceiling complete all as specified and as directed. |
| 16 | M&L Rendering 15mm thick cement plaster on fair faces of brick work or concrete surfaces in cement mortar (1:4) in two layers (5mm finishing layer over 10mm base layer) finished even and smooth without using extra cement complete all as specified and directed |
| 17 | M&L Rendering 10mm thick cement plaster on fair faces of brick work or concrete surfaces in cement mortar (1:6) finished even and smooth without using extra cement complete all as specified and as directed. |
| 18 | M&L Preparation of newly plastered or concrete surfaces and applying two coats of cement base paint on wall surfaces over one coat of alkali resistance primer complete all as specified and directed. |
| 19 | M&L three coats of white wash on surface of wall including preparation of new plastered surface complete all as spd and directed. |
| 20 | M&L for preparation of newly plastered surfaces of ceiling and applying three coats of white wash without any brush marks on the surface including necessary scaffolding up to four storeys height of bldgs if required complete all as specified and as directed. |
| 21 | M & L preparation of new wood/plywood or wood / plywood based surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer. |
| 22 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm. in hard/dense soil. |
| 23 | Removing excavated material n.exc 50m and depositing where directed at a level n exc 1.5m above the starting point. |
| 24 | Removal of excavated soil to a distance exc.50 Mtr and n.exc. 150 Mtr and deposited as directed by Engineer-in-Charge. |
| 25 | M&L for 19-20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite. |
| 26 | M&L for moorum/red bajri filling in floors or pavings, laid in layers n exc.15 cm thick, spread, levelled and rammed including watering complete all as specified and directed. |
| 27 | M&L for hard core of gauge n exc 63mm broken stone boulders, deposited,spread and levelled in layers n exc 15cm thick, watered and rammed to a true surface etc complete all as spd. |
| 28 | M&L for 75 mm thick PCC 1:4:8 type D-2 as in subbase to flooring complete all as specified and as diretcted. |
| 29 | M&L for 25 mm thick Cement concrete type B-1,1:2:4 (20mm graded aggregate) as in subbase to flooring complete all as specified and as diretcted. |
| 30 | M&L Cement concrete type C-2, 1:3:6 (using 40mm graded aggregate) as in plinth protection and paving 75mm thick laid in slope finished even and fair incl making joints at every 2.5 m and at corner filled with bitumen 85/25 and sand in ratio 1:2 by weight and complete all as specified |
| 31 | S&F for non skid coloured Ceramic tiles 07mm to 08mm thick (square/ rectangular) area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:4 complete all as specified and directed. |
| 32 | M&L for glazed ceramic coloured tiles in vertical surface 450x350x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match incl rendering 10mm thick in CM (1:3) and finished rough complete all as spd & directed. |
| 33 | M&L for chequered cement concrete tile 20cmx20cmx25mm/30cmX30cmX25mm thick set jointed and pointed in neat cement siurry in floor with grey cement and pig ments over and including 20mm thick screed bed or bedding layer of CM (1:4) complete all as specified and as directed. |
| 34 | M&L for cement concrete Type B-0 using 12.5mm graded stone aggregate (Nominal mix in 1:2:4) in copings, benching and the like including weathering slightly rounded or chamfered angles as directed including necessary form work and finishig all exposed surfaces complete all as specified. |
| 35 | Supply and fix Solid PVC Door Frame of size 50mm x 47mm made out of 5mm wood grain printed PVC sheet & edges will be painted to match with printed sheet ,reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed. |
| 36 | S&F for factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded wood grain printed PVC sheet PVC ‘C’ channel having a plain colour PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and wood grain printed PVC sheet for top rail,lock rail & bottom rail on either side & as gap insert for top rail & bottom rail;Panelling of wood grain printed PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable & 5mm thick x15mm wide PVC sheet beading used inside stiles and rails and decorative PVC beading of 10mm x 10mm (900 ) used instead of exposed portion of PVC sheet beading suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed. |
| 37 | S & F 2nd class hard wood plain solid straight chowkats and frame of wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joints complete all as specified and directed. |
| 38 | S&F mild steel work, Grade Fe-410-0 or Fe- 310-0, as in flat iron (for holdfast) complete all as specified and as directed. |
| 39 | S&F 30 mm thick second class hard wood Glazed and skeleton shutters for window and ventilators etc, open rebated and prepared to receive glass, gauze, etc. (with sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beds for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.24 (b) |
| 40 | S&F 30 mm thick 2nd class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauge etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc ; sizes of members of shutters as specified in SSR Part-I, section-8, clause 8.24(a). |
| 41 | M&L 3 mm thick plain glass sheets ordinary quality in squares n exc 0.5sqm each pane fixed with aluminium frame work etc all as specified and directed. |
| 42 | S&F for 100 mm long Butt hinges, medium weight, cold rolled mild steel, and fixed |
| 43 | Supply and fix Aluminium, anodised, barrel tower bolts of extruded section and fixed, Length of bolt in 150mm complete all as specified and directed |
| 44 | S & F 150mm size extruded aluminium alloy handles, fabricated type anodised |
| 45 | S&F for rotational moulded polyethlene water storage tanks three layers of 1000 ltrs capacity ISI marked (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including 15mm thick Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed. (Minimum weight 20mm-210 gms of inlet, outlet & over flow pipe etc complete all as specified and as directed. |
| 46 | S&F for 20mm bore Steel water tubing 'medium grade', galvanised with all fittings like elbow, tee, socket, bend etc and fixed to wall, ceiling or laid in floor complete all as specified and directed. |
| 47 | S&F 15mm bore tubes medium grade galvanized ISI marked with all fittings short pieces and fixed including concealed pipe to walls, floor, ceiling etc complete all as specified. |
| 48 | S & F for 15 mm bore long body CP Bib taps cast copper alloy fancy type with capstan heads (chromium plated),and cup screwed down , high pressure for iron pipe mpete all as spd & directed. |
| 49 | S&F 15 mm dia bib taps, fancy type chromium plated, screwed down, screwed for iron pipe or for brass ferrule and fixed. |
| 50 | S & F for 15 mm bore Stop valves, fancy type, chromium plated cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed. |
| 51 | S&F for CP Pillar taps fancy type 15 mm bore, cast copper alloy, with capstan heads screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks & fly-nuts, screwed for iron pipe complete all as specified and directed. |
| 52 | S&F for Gun-metal, globe or gate valves 15mm bore, with iron wheel head, screwed both end for iron pipe |
| 53 | S&F for Gun-metal, globe or gate valves 20mm bore, with iron wheel head, screwed both end for iron pipe |
| 54 | S&F for Tubular towel rail, ISI marked 60cm long between flanges , 20mm dia 'D' type Brass Chromium plated incl brackets, fixed with chromium plated brass screws and wooden/plastic cleats complete all as specified and directed. |
| 55 | S&F for 600 mm x 450 mm bevelled edge mirror of selected quality glass mounted on 6 mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers all as spd. |
| 56 | S&F for 15mm dia 600 mm long PVC connection including brass check nut at both ends screwed both end for iron pipes. |
| 57 | S & F for 32/40 mm bore PVC waste pipe flexible with minimum length 800mm complete all as specified and directed. |
| 58 | S&F 32 mm bore Low density poly ethylene pipes of pressure rating 6kgf/cm2 fixed complete to walls,ceiling or in floors etc. |
| 59 | Supplied and fixed PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors all as specified and directed. |
| 60 | Supplied and fixed PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors all as specified and directed. |
| 61 | Supplied and fixed PVC (SWR) pipes 75mm bore single socketed in any length with rubber ring joints fixed to walls all as specified and directed. |
| 62 | Supplied and fixed PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joints fixed to walls all as specified and directed.(ISI MARKED) |
| 63 | S&F PVC (SWR) bends any radius with access door, 75mm dia. |
| 64 | Supplied and fixed PVC (SWR) bends any radius 75mm dia all as specified and directed.(ISI MARKED) |
| 65 | Supplied and fixed PVC (SWR) bends any radius 110mm dia all as specified and directed.(ISI MARKED) |
| 66 | S&F PVC (SWR) junction single, (single T) equal or unequal with access door 110mm dia. |
| 67 | S&F PVC (SWR) vent cowl 110mm dia |
| 68 | S&F PVC (SWR) WC connector 110mm dia lip ring. |
| 69 | S&F 75 mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement. |
| 70 | S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified |
| 71 | S&F for Vitreous China wash down water closet pan including P or S trap of bore 125/110 mm (pedestal pattern), white or in matching colour of tiles (excluding flushing cistern and flush pipe) including plastic water closet seat, white or in matching colour , closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device and wash down water closet complete all as specified and as directed. |
| 72 | S&F for viterous China squatting pan, `Orrisa' pattern, size 580 x440 mm white, witht integral foot rests (excluding flushing cistern and flush pipe) including connection to trap,and to flushing pipe, anti-syphonage pipe,etc. complete including making good to floor complete all as specified and as directed. |
| 73 | S&F for 10 ltrs capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with intel, ball valve, float and handle including brackets ,fush pipe of polyethylene of low or high density or PVC 32 mm dia complete all as specfied and as directed. |
| 74 | S&F for Viterous China wash basin, white, flat back, size 550x400mm excluding taps etc but including brackets,including cutting for and pinning in ends of brackets or erecting stand but including waste coupling of fixing of supply and waste pipe complete all as specfied and as directed. |
| 75 | S&F 0.50mm thick pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet of any colour having tensile strength of 550 Mpa as in roof covering, fixed with self tapping screws etc complete all as specified and directed. (Note:- Item rate shall be include any height of Bldgs / Hangars for scaffolding as all arrangement.) |
| 76 | S&F for roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. |
| 77 | S & F in mild steel work conforming to Fe 290 Gde-E-165 in posts, wall & struts angle including cutting top to shape as directed, drilling holes, notching for wire, etc; flat iron fillets ( for securing wire mesh etc) including all necessary drilling, bolting or riveting etc complete all as specified & directed. |
| 78 | Supply and fix 600mmx600mmx4mm thick ‘E’ Board Classic as in false ceiling including supply and fixing GI ‘Tee” grid frame work made of special section of M.S galvanized sheet 0.30mm thick , bottom portion painted with cellular nitro painting, warping the suspending wire around the existing wooden/steel purlin /rafter for suspending grid frame work of size 605mmx605mm suspended with 4 mm dia GI wire @ 1200mm c/c on main Tee and fixed to T-grid with the help of level clip or as per manufacturer direction. The section consisting of main Tee 37mmx24mmx0.60mm, cross runner tee 37mmx24mmx0.60mm and perimeter angle of 24mmx24mmx0.50mm thick. Perimeter angle to be fixed to wall with GI screw of 40mm long @ 450 mm c/c along the perimeter of wall including applying two coats of distemper oil emulsion complete all as specified and directed |
| 79 | M&L for Providing precast cement concrete solid building blocks exc 20cm in width of type C1 (1:3:6) (20mm graded stone aggregates) and setting in cement mortar 1:6,complete, in walls, complete all as specified and directed. |
| 80 | M&L for preparation of new steel surfaces / MS sheet of any description over 10 cm width or girth and applying two coats of synthetic enameled paint over a coat of red oxide primer all as specified and directed. |
| 81 | S&F for Health Faucet ABS body with 1 meter SS brided connection pipe long Flexible Tube Chrome Finish & Wall Hook for Water closet complete all as specified and directed. Make- Cera CAT No. F8030111AB or equivalent in any of the make metnioned in list of product. |
| 82 | S&F vitreous china EWCs snow white county 700 x 350 x 745 mm with slim soft close seat cover S trap 300mm complete all as specified and directed. Make-CERA Cat No.S1013252 or equivalent in any of the make metnioned in list of product. |
| 83 | S&F for vitreous Urinal snow white of size 365 x 335 x 670mm with grating and union for discharge pipe fixed to wall complete all as specified and directed. Make-CERA Cat No.S4020107 or equivalent in any of the make metnioned in list of product. |
| 84 | M&L for viterous china urinal partition white of size 310 x 700mm urinal partions slabs, terminating about 40cm above floor, fixed in repairs complete all as specified and directed. |
| 85 | S&F for soap dish of size 160x160x90mm, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed. |
| 86 | Excavating over areas, n.exc 1.5 mtr in depth; for foundation etc. and getting out in hard/dense soil as directed and specified by Engr-in-charge. |
| 87 | Excavating over areas, exc 1.5 mtr but not exc 3.00 mtr in depth; for foundation etc. and getting out hard/dense soil as directed and specified by Engr-in-charge. |
| 88 | M & L for TMT 6 to 8 mm cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips |
| 89 | M&L for Formwork to edges of concrete flats, treads, breaks in floors,window cills, concrete rail ings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizon tal or sloping and similar work exc 10cm but n exc 20cm wide rough finish surface of concrete |
| 90 | M&L Pre-cast cement concrete cover slab for manhole and drain cover in plain cement concrete 1:2:4 type B-1, (using 20 mm graded stone aggregate) set in cement mortar 1:4 with plain faces complete all as specified and as directed. (Note:- Reinforcement shall be measured and paid seperately) |
| 91 | M&L for rendering 15 mm thick in CM (1:4) on fair faces of brick work or concrete surfaces to be finished even and smooth without using extra cement mixed with intergral water proofing compound @ 3% by weight of cement (WPC measured and paid separately) all as specified and as directed. |
| 92 | Supply only integral water proofing compound all as specified and as directed. |
| 93 | M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed. |
| 94 | M&L cement concrete type B-1 (1:2:4) (20 mm graded aggregate) as in kerb stones ,coping, bed plates and the like including weathering, slightly roundered or chamfered angles and throating, as directed including necessary form work and finishing complete all as specified. |
| 95 | M&L PCC 1:3:6 type C-1 (using 20mm graded aggr) as in surface channels & drains,benching of manholes complete allas spd and directed. |
| 96 | Extra for forming fair finished drain or channel 30cm inner grith in cement concrete, using extra cement, including forms, moulds, mitred/stop ends etc. |
| 97 | Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, in hard/dense soil. |
| 98 | M&L PCC 1:4:8 type D2(using 40mm graded aggregate)as in foundation filling and mass concrete etc. |
| 99 | Use & waste Form work to edges of concrete flat, tread, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 5 cm but n.exc 10 cm wide for rough finish surfaces of concrete. |
| 100 | M&L rendering 15 mm thick in CM 1:4 on concrete surfaces finished even and smooth without using extra cement . |
| 101 | M&L for rendering 15 mm in CM (1:6) over concrete wall surfaces finished even and smooth without using extra cement. |
| 102 | M&L Preparing newly plastered surfaces of walls and applying two coats of white wash. |
| 103 | M&L for 75 mm thick PCC 1:3:6 type C2 (using 40 mm graded stone aggregate) as cement concrete in Sub-base floors, sub-bases floors and pavings etc complete all as specified. |
| 104 | M&L for 15 mm thick screed bed in CM 1:4 for laying floor tiles . |
| 105 | M & L for Non-skid ceramic tiles 7 to 8 mm thick coloured tiles( square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match. |
| 106 | S & F 3mm thick figured glass, pin head glazing with oil putty /wooden beads in squares n exc 0.50 Sqm in each pane. |
| 107 | S&F 100mm size stainless steel butt hinges, medium weight, cold rolled complete with stainless steel screw etc. all as specified as directed. |
| 108 | S&F of Vitreous China urinals, bowl type of size (465x355x265mm) (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. complete all as specified and directed by engr in charge. |
| 109 | S&F PVC connection of 15 mm size with PTMT nuts of length 450 mm |
| 110 | S & F Rolled sections as in framing for cladding, glazing and the like fixed with angle cleats and connecting plates, etc. conforming to e 410-W (GdeE- 250) qualityA complete as specified. |
| 111 | S&F Rotational mounded polythene water storage tank of 500 ltrs capacity, (multilayered, cylindrical, vertical with closed top) hoisted and fixed in position as specified in SSR Pt-I. |
| 112 | S&F ball brass valves high pressure with polythene float and fly nut complete screwed for iron pipes of 20 mm dia or brass ferrule and fixed, all as directed. |
| 113 | M&L for construction of 1.20 m dia x 3.00 m deep soakage well, excavation in hard/dense soil foundation PCC 1:3:6 ,wells of honey combed stone masonry wall, including intercepting chamber, screen chamber, RCC cover slab, filling with brick bats etc complete all as specified. |
| 114 | Material and labour for providing PCC (1:3:6) type C-2 as in concrete bed to drain pipes including packing under and haunching against the sides of pipes of bore 150mm on after they are laid and tested complete all as specified and directed.. |
| 115 | Material and labour for providing PCC (1:3:6) type C-2 as in concrete bed to drain pipes including packing under and haunching against the sides of pipes of bore 100mm on after they are laid and tested complete all as specified and directed.. |
| 116 | Material and labour for Salt glased stone ware drain pipe 150 mm dia grade A laid in trenches and jointed in cement mortar 1:1 complete all as specified and directed. |
| 117 | Material and labour for Salt glased stone ware drain pipe 100 mm dia grade A laid in trenches and jointed in cement mortar 1:1 complete all as specified and directed. |
| 118 | Supply only Chain link MS galvanisd fencing, any size or type all as specified and directed. |
| 119 | Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc.including provission of binding wire all as specified. |
| 120 | M&L Mild Steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete. Steel of grade Fe 410 -W (Gde- E- 250) quality-B |
| 121 | S&F Mild steel screw bolts diameter of neck from 5 to 10 mm (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long all as specified. |
| 122 | M&L Cement concrete, type c2, 1:3:6 (40mm graded aggregate) in foundations, filling and mass concrete in walls or retaining walls, any thickness, size or shape including pilasters, buttresses columns, pillars, boundary pillars and posts (including caps and bases) complete all as specified and as directed. |
| 123 | Removal of unserviceable material obtained from demolition to a distance of exc 250m but n. exc 1000m beyond the lead included in the rates, including loading, unloading and stacking at the destination, |
| 124 | Material & Labour for Point wiring with 1.5 sq mm (nominal area), PVC insulated unsheathed (FRLSH), 1100 volts grade, multi-stranded copper conductor, in and including PVC casing capping of adequate size with all fittings and accessories including PVC boxes for housing the switches ( Make of box Prestoplast,Prestoteak), including PVC insulated and unsheathed (FRLSH)single core multi-stranded copper conductor cable of size 1.5 sq mm green in colour as earth continuity conductor connected to common earth dolly for one light/ fan point controlled by one switch complete all as specified and directed. |
| 125 | All as per item No. 124 here in before but for one 3 pin socket outlet 5 Amps three pin controlled by one switch on independent board complete all as specified directed. |
| 126 | All as per item No. 124 here in before but for one 5 pin socket outlet 15 Amp and 5 Amp Multipurpose independent using 2.5 Sqmm copper conductor cable (multi-strand) PVC insulated and unsheathed cable and 2.5 sqmm copper (multistrand) PVC insulated and unsheathed earth wire complete all as specified. |
| 127 | M&L for Point wiring for one socket outlet 15 Amp on independent board with 4 sq mm (nominal area), PVC insulated unsheathed (FRLSH), 1100 volts grade, multi-stranded copper conductor, in and including PVC casing capping of adequate size with all fittings and accessories including PVC boxes for housing the switches ( Make of box Prestoplast,Prestoteak), including PVC insulated and unsheathed (FRLSH)single core multi-stranded copper conductor cable of size 4 sq mm green in colour as earth continuity conductor connected to common earth dolly complete all as specified and directed. (For Geyser ) |
| 128 | S&F Socket outlet 2 in 1, 3 pin, 5 and 15 amp flush type |
| 129 | S&F Socket outlet 2 in 1, 3 pin, 5 amp flush type |
| 130 | Supply & fixing switch piano flush type (ISI marked), single pole, one way 15 Amp, 240 Volts complete all as specified & directed. |
| 131 | Supply and fixing ceiling rose, surface bakelite, 65mm x 50mm , two to three terminals complete all as specified & directed. |
| 132 | Supply & fixing switch piano flush type (ISI marked), single pole, one way 5 Amp, 240 Volts complete all as specified & directed. |
| 133 | Supply and fixing LED light fitting 1 x 20 Watt 220 volt AC decorative box type with driver, holder including LED tub light connecting up with three core flexible copper conductor cable of size from ceiling rose complete all as directed. |
| 134 | Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete. complete all as directed. |
| 135 | S&F LED bulkhead fitting 10 watt (Endura Ruby) with all accessories and including connenting up with twin core twisted with flexible copper conductor cable with suitable size of 230 volts , 50 hz complete all as spicified and directed. |
| 136 | Supply and fix sheet metal enclosures for DBs Single door when MCBs to be used 230 volts 4 way 200 Amp rated busbar single pole and neutral fixed on wall duly grouted in solid block wall or on wooden board. |
| 137 | Supply and fix sheet metal enclosures for DBs Double Door when MCBs to be used 230 volts 4 way 200 Amp rated busbar single pole and neutral fixed on wall duly grouted in solid block wall or on wooden board. |
| 138 | S&F MCB SPN having braking capacity 10KA, 32 Amps, 240 V complete all as specified and directed. |
| 139 | S&F MCB SP having braking capacity 10KA, 6 to 32 Amps, 240 V complete all as specified and directed. |
| 140 | Supply and fix electric water heater(Geyser), storage type steel body with copper inner tank and heating element up to 2 KW capacity 25 litre, BEE 5 star rated adjustable temprature setting 0-90 degree C complete with accessories such as safety wall, thermostate, NRV indication lamps, inlet outlet connections,air vent connections, connection pieces including all fixing arrangements such as fastners, bilts, nuts washers etc including making good disturbed wall surfaces matching with the existing surface and finishing complete all as specified and directed by Engr in charge |
| 141 | S&F Stop valves, cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe of size 15 mm. |
| 142 | S&F Bib tap cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed all as specified & as directed by engr-in-charge. |
| 143 | Material & labour for earthing complete with galvanised steel earth plate electrode 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25m deep below the ground level) with top edge of the plate not less than 1.5mtr below the normal ground level connected to GI Wire of 4 mm Dia as earthing lead by means of bolts, nuts, check nuts and washers of galvanised iron.Earth wire protected by GI pipe 15 mm bore(medium grade) and connected to main switch board or main control board as directed and as specified and shown in electrical plate No. 3 of SSR Part I (2009) including necessary concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 40 cm x 40cm x 5cm reinforced with 8mm dia TMT bars @ 15cm C/C with one handle for lifting made out of 8mm dia bar, funnel, wire mesh, 20mm dia GI pipe medium grade for watering, charcoal or coke and salt in alternate layers including necessary excavation and earth work in any type of soil and testing complete all as directed by Engineer-in-Charge. |
| 144 | Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250 mm |
| 145 | S&F wire for circuit/sub main wiring with 1100 volts grade double core PVC insulated and unsheathed cable with multistranded copper conductor 6 Sqmm, on surface or recessed or drawn in PVC casing capping/PVC Pipe along with 4 Sqmm single core copper conductor multi stranded cable as earth continuity conductor complete all as specified and as directed.(Note: One RM PVC casing capping/PVC conduit ,one run of 4 sqmm earth wire and 2 Run of 6 sqmm cable shall be measured as one run.) |
| 146 | S&F in replacement of LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete. |
| 147 | S&F of new generation energy saving and environmental friendly long life LED building security light made up of innovative die cast aluminium housing high power LED as lighting source with IP - 66 power consumption 35 watt complete input voltage of 150-240 Volt (nominal rated voltage 240 Volt) complete including twisted 3 core copper cable of size 1.5 Sqmm dia for connecting phase, neutral and earth from ceiling rose to light length as required at site,GI bracket 32 mm dia pipe and 02 numbersclmaps, all fixing arrangements such as fastners, bilts, nuts washers etc all as specified and directed. |
| 148 | S&F in replacement of 1100 Volts grade heavy duty ISI marked cable PVC insulated stranded aluminium conductor one twin core cable flat or circular of size 10 sqmm served with inner sheathing of PVC tape & overall PVC sheathed in service connections |
| 149 | S&F in replacement of 1100 Volts grade heavy duty ISI marked cable PVC insulated stranded aluminium conductor one twin core cable flat or circular of size 6 sqmm served with inner sheathing of PVC tape & overall PVC sheathed in service connections Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 03, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 24, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 20 daysAug 31, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 27 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender