Tender For Addition Alteration To Sncos Living In Accommodation And Provision Of Cycle Shed At Dsc Mess At Af Stn Palam Under Ge (Af) Palam, Delhi Cantt - 10
Tender Value
16.40 Lakhs
Estimated cost
Bid Submission
22 Aug 2026
6 days left
EMD
32800
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
New Delhi → Delhi
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Addition Alteration To Sncos Living In Accommodation And Provision Of Cycle Shed At Dsc Mess At Af Stn Palam Under Ge (Af) Palam, Delhi Cantt - 10
BOQ
| Sl. No. | Item Description |
| 1 | Excavation in trenches n exc 1.5m in depth and 1.5m in width and getting out in soft/loose soil complete all as specified and as directed. |
| 2 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25cm thick in hard/dense soil complete all as specified and as directed. |
| 3 | Removing excavated material (soil) n. exc 50m and deposited where directed at a level n exc. 1.5m above the strating point complete all as specified and as directed. |
| 4 | Demolition of cement concrete or lime concrete (un-reinforced) of any description and in any position not otherwise specifically provided for and removing the debris outside defence land from the site complete all as specified and as directed. |
| 5 | M&L for PCC (1:4:8) type D-2 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and as directed. |
| 6 | M&L for brick work with sub-class `B' bricks, straight or curved on plan exceeding 6 M mean radius built in cement mortar (1:6) complete all as specified and as directed by Engineer-in-Charge. |
| 7 | M&L for brick work with sub-class `B' bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar (1:4) complete all as specified and as directed by Engineer-in-Charge. |
| 8 | M&L for 100mm thick PCC (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) as in floor, surface finished even and smooth using extra cement complete all as specified and as directed. |
| 9 | M&L for 25mm thick PCC (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) as in floor, surface finished even and fair without using extra cement complete all as specified and as directed. |
| 10 | M&L for joint free non skid coloured ceramic tiles, 7 to 8mm thick (squre or rectangular) area of each tile exc. 0.11sqm but n exc 0.18sqm, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces, laid over and including 15mm thick screed bed in cement mortar (1:6) complete all as specified and as directed. |
| 11 | M&L for coloured glazed ceramic tiles as in vertical surfaces of size (450 x 300)mm x 7mm thick, set and jointed in neat cement slurry and pointed in white or colour cement to match over and including rendering 10mm thick in CM (1:4) on fair faces of brick work or concrete surfaces as backing coat complete all as specified and as directed. |
| 12 | M&L for glazed ceramic tiles, light shase 8 to 10mm thick (squre or rectangular), polished, double charges, area of each tile n exc. 0.36sqm, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces, laid over and including 15mm thick screed bed in cement mortar (1:4) complete all as specified and as directed. |
| 13 | S&F pressed steel frames made out mild steel sheet 1.25 mm thick, with size of frame 105 mm x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates, hold fasts etc and applying a shop coat of red oxide primer including providing PCC (1:3:6) type C-0 using 12.5 mm graded crushed stone aggregate for filling hollow portion of chowkhats complete all as specified and as directed by the Engineer-in-Charge . |
| 14 | S&F pressed steel frames made out mild steel sheet 1.25 mm thick, with size of frame 125 mm x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates, hold fasts etc and applying a shop coat of red oxide primer including providing PCC (1:3:6) type C-0 using 12.5 mm graded crushed stone aggregate for filling hollow portion of chowkhats complete all as specified and as directed by the Engineer-in-Charge . |
| 15 | S&F rolled mild steel grade Fe-290 Gde-E-165 as in framed work as in doors or gates of angle or other section gates of with gusset plates, rails, cladding, chowkhats/frame or like etc welding hold fast, hinges complete all as specified and as directed. |
| 16 | S&F solid PVC door frame of size (50mm x 47mm) made out of 5mm plain colour PVC sheet reinforced with MS square tube, suppling & fixing in opening as per specification & drawing complete all as specified and as directed. |
| 17 | S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tube for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC `C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stliles and rails with suitable PVC sheet beading, and jointed together with solvent cement, supplying & fixing in the frame at site as per specification and drawing complete all as specified and as directed. |
| 18 | M&L for 2nd class hard wood factory made 35mm thick glazed and skelton shutters open repated and prepared for door to receive framing plain chamfered or rounded fitted with cut and mitered heads for securing stainless steel wire cloth 0.36mm nominal dia of wire and average width of apertupre 1.40mm and second class hard wood plain fillets, square, rectangular or triangular in section, and secured with nails or screws, clean sawn and sectional area exc 13 Sq cm and not exc 25 Sq cm with and including two coats of synthetic enamel paint over one coat of pink primer complete all as specified and as directed. Note:- (a) The cost of sash bars, 01 no mild steel 300mm size ordinary rat tail rod pattern springs including roller and roller plate, 2 nos 150mm aluminium handles, 2 nos 200mm long aluminium tower bolts, 3 Nos 100 mm size aluminium hinges, necessary wooden fillets min 5Rm in each shutter and stainless steel wire mesh and two coats synthetic enamel painting over a coat of primer shall be deemed to be included in unit rate. |
| 19 | S&F windows & ventilators fabricated from rolled formed GI section made of galvanised steel colour coated (PPGI Sheets) (Base steel as per IS 513 ‘’D’’ quality). Galvanised as per IS 277 with Zinc of 120 gms/Sqm. PAINT: Pre-Painted sections should be with primer coat of epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyl backer of 5-7 microns or powder coated with pure polyester powder upto 50-60 microns thick. GI section of 0.58mm thick in double rebate windows in both glazed shutter and flymesh shutter, (75 x 58)mm outer frame, mullion (74 x 53)mm, glazed shutter (52 x 50)mm, flymesh (42 x 21)mm, beading for glass fixing (12 x 12)mm in fixed portion and the outer frame and mullions to have rebate for glazed/gauzed shutters the sections cut to length metre joined with corner Poly Vinyl Chloride brackets centre mullion fixed with Poly Vinyl Chloride Mullion caps. Glass of 4mm thick plain float glass fitted with rubber gasket in glazed shutter and wiremesh of stainless steel of 36 guage to fix mesh in mesh shutter using VC Gypsum drywall screws and spoon profile of 0.58mm GI Sheet. Corners of the windows should be joined with corner brackets made of poly vinyl chloride with CRCA of zinc phosphate coat. Each glazed shutter and fly mesh shutter shall be provided with SS Pivot Hinges 2 nos in each, Poly Vinyl Chloride handle - 1 no in each and powder coated peg stay in glass shutter. Window shall be provided with enamel paint MS Grill/ guard bars made of 10mm horizontal MS square bar welded to 6 x 12mm MS flat with holes at both vertical ends. Gap between the bars should not be more than 152mm. Window frames shall be fixed to brick / concrete masonry by using nylon self expansion caps & 75/100mm MS screws after drilling in walls. VC Gypsum drywall screws should be used while fixing corner brackets, stay, hinges, mullion caps of windows. Type-4000 series ref drg No CEAF/STD-191/2014 SH1/2&2/2. |
| 20 | M&L in repair for MS works as in holdfast, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging holdfasts, grills, cladding and similar small articles conforming to Fe 290 Gde E-165, complete all as specified and as directed. |
| 21 | S&F butt hinges, medium weight, cold rolled mild steel 100mm size complete all as specified and as directed. |
| 22 | S&F aluminium, anodised, barrel tower bolts 200mm size of extruded section complete all as specified and as directed. |
| 23 | S&F in repair 200mm long aluminium anodised, handle of extruded section fabricated type complete all as specified and directed. |
| 24 | S&F aluminium alloy, anodised, sliding door bolt 300mm length with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed by Engineer-in-Charge. |
| 25 | S&F factory made 18mm (+0.7mm) thick celuka PVC board of density 600 kg/cum manufactured by an ISO 900-2008 certified company having one side perlaminated and other side plain fixed as in cabinet/ cupborad shutters including provding manufactures test report and test certificate is mandatory with each and every supply of material including taking down of existing shutter or any kind of PL board or plyboard completed all as specified and as directed. |
| 26 | S&F factory made 18 mm (+0.7mm) thick celuka PVC board of density 600 kg/cum manufactured by an ISO 900-2008 certified company fixed as in shelves perlaminated/ cabinet/cupboard drawers including providing manufacturer's test report and test certificate is mandatory with each and every supply of material including taking down of existing shelves or any kind of PL board or plyboard complete all as specified and as directed. |
| 27 | S&F factory made 5 mm thick PVC sheet of density 600 kg/cum manufactured by an ISO 900-2008 certified company, plain 5mm thick PVC sheet panelling for back side (wall side) with and including taking down of existing back side (wall side) or any kind of PL board or plyboard complete all as specified and as directed. Note:- Manufacturer's test report and test certificate is mandatory with each and every supply of material. |
| 28 | S&F 30mm width of flaps continuous (piano) hinges, stainless steel, bright finish or electrogalvanised complete all as specified and as directed by Engineer-in-Charge. |
| 29 | S&F hasp & staple 125mm size, safety type aluminium anodised with mild steel hinge pin including bolt, two hinge plate and fixed with screws complete all as specified and as directed by Engineer-in-Charge. |
| 30 | S&F floor door stopper double legged with rubber shoe of aluminium alloy body 140 mm cover plate and tounge, anodised with hard drawn steel spring fixed in floor complete all as specified and as directed by Engineer-in-Charge. |
| 31 | S&F in repair mild steel ordinary rat tail rod pattern springs including roller and roller plate of 300 mm length complete all as specified and as directed by Engineer-in-Charge. |
| 32 | S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed. |
| 33 | S&F in repair minimum 20mm dia and not less then 1mm tthick aluminium Drapery rod, PVC coated finish including teak wood brackets & end knob as required with teak wooden curtain rings etc complete all as specified and as directed. Note:- Minimum 2 Nos brackets, 02 Nos End knob and 12 Nos rings in each door/ window shall be provided. |
| 34 | M&L for 75mm thick PCC (1:3:6) type C1 (using 20 mm graded stone aggregate) as in plinth protections, to be finished even and smooth without using extra cement complete including use and waste of necessary form work complete all as specified and as directed. |
| 35 | M&L for providing reinforcement cement concrete (1:2:4) nominal mix type B1 (using 20mm graded stone aggregate) as in roof beams, lintel, cantilever etc complete all as specified and as directed. |
| 36 | M&L for providing reinforcement cement concrete (1:2:4) nominal mix type B1 (using 20mm graded stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed. |
| 37 | Use and waste of formwork to soffits of floor beams, beam haunching, lintel, cantilever etc complete all as specified and as directed. |
| 38 | Use and waste of formwork to soffits of suspended slabs such as roof slabs, facia, chhajja etc complete all as specified and as directed. |
| 39 | M&L for PCC (1:2:4) type B-0 (using 12.5mm graded stone aggregate) as in roof padding, kerbs, coping, window cills, benching etc including weathering, slightly rounded or chamfered angle and throating complete all as specified and as directed. |
| 40 | M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed. |
| 41 | S&F 5 to 10 mm dia TMT bars, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends as in strrrups and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed. |
| 42 | Taking down cement or cement lime plaster on brick or stone walls, etc. including raking out joints, hacking for keys, scrubbing down with water, etc complete all as specified and as directed by Engineer-in-Charge. |
| 43 | M&L for 15 mm thick cement plaster on fair faces of brick work or concrete surfaces in cement mortar (1:4), to be finished even and fair with mixing water proofing compound by weight as per manufacturer's instructions including necessary scaffolding up to (G+3 storey) complete all as specified and as directed. Note:- WPC shall be measured and paid separately. |
| 44 | M&L for 10mm thick plaster on fair faces of brick work or concrete surfaces in cement mortar (1:3) as in ceilings, to be finished even and smooth without using extra cement complete all as specified and as directed. |
| 45 | M&L for 15mm thick cement plaster on fair faces of brick work or concrete surfaces in cement mortar (1:6), to be finished even and smooth complete all as specified and as directed. |
| 46 | M&L for preparation of new plaster surface of walls, chajjas, soffits & beam including necessary scaffolding and applying two coats of acrylic smooth exterior paint of required shade 1.43 ltr / 10sqm over a coat of exterior primer 2.20 kg / sqm complete all as per manufacturer's instructions and as directed by Engineer-in- Charge. |
| 47 | M&L for preparation of new plastered or unplastered surfaces of wall/ ceiling and applying 3mm thick (average) cement based wall care putty over a coat of alkalic resistent primer and two coats of oil bound distemper complete all as specified and as directed by Engineer-in-Charge. |
| 48 | M&L for preparation of plastered or unplastered new surfaces on walls and applying three coats of white wash complete all as specified and as directed. |
| 49 | M&L for preparing plastered or unplastered new surfaces on walls including brooming down or steel wire brushing, scraping down and applying two coats of cement base paint of approved colour complete all as specified and as directed. |
| 50 | M&L for complete removal of existing treatment of walls, chajjas, soffits & beam including necessary scaffolding by mechanically washing, rubbing down and stopping of surface holes and cracks using necessary filling compound of white cement and fine sand in ration (1:3) to obtain smooth finish and applying two coats of exterior paint of required shade @ 1.43 ltr / 10sqm over a coat of exterior primer @ 2.20 kg/sqm complete all as per manufacturer's instructions and as directed by Engineer-in- Charge. |
| 51 | M&L for prepration of old decorated plastered surfaces of walls /ceilings, removal of nails etc & filling cracks/hole by applying cement base wall care putty as required (multipurpose mixer shall be used for uniform and proper mixing of putty) and applying one coat of oil bound distemper white or coloured complete all as specified and as directed by Engineer-in-Charge. |
| 52 | M&L for complete removal of existing treatment from old decorated plastered surfaces of walls and ceilings by removal of nails etc & filling cracks/hole with putty as required (multipurpose mixer shall be used for uniform and proper mixing of putty) and applying two coats of oil bound distemper white or coloured by roller complete all as specified and as directed by Engineer-in-Charge. |
| 53 | M&L for preparation of old painted surfaces of steel and iron surfaces of any description not otherwise described over 10cm width & girth and applying one coat of synthetic enamel paint complete all as specified and as directed by engr-in charge. |
| 54 | M&L for preparation of new or previously untreated wood and wood based surfaces of any description exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed by Engineer-in-Charge. |
| 55 | M&L for applying 2mm thick cement base wall care putty on wall / ceilings, etc complete all as specified & directed by Engineer-in-Charge. |
| 56 | M&L for preparation of new or previously untreated surfaces of steel of any description not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed. |
| 57 | S&F 110mm dia PVC (SWR) pipes, single socketed in any length with rubber ring joints fixed to walls and floors with and including suitable clamps at one metre of interval complete all as specified and as directed. |
| 58 | S&F PVC (SWR) bends of radius, suitable for 110mm dia PVC pipes fixed complete all as specified and as directed. |
| 59 | S&F GI tubes 15 mm bore 'medium grade' with all fittings and fixed complete to walls and ceilings or laid in floor or any other situation including taking up or down unserviceable steel water tubing with fittings and connections etc complete all as specified and as directed by Engineer-in-Charge. |
| 60 | S&F GI tubes 20mm bore 'medium grade' with all fittings and fixed complete to walls and ceilings or laid in floor or any other situation including taking up or down unserviceable steel water tubing with fittings and connections etc complete all as specified and as directed by Engineer-in-Charge. |
| 61 | M&L for 150mm thick concrete bed to drain pipes in cement concrete (1:3:6) type C-1 (using 20mm graded stone aggregate) including packing under and haunching against the sides of pipes after they are laid and tested for 150 mm bore pipe complete all as specified and as directed. |
| 62 | M&L for salt-glazed stone ware drain pipes, internal dia of pipe 150mm laid in trenches and jointed complete all as specified & directed by Engineer-in-Charge. |
| 63 | S&F 500 litres capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) three layered white, hoisted and fixed in position all as specified in SSR Part I with and including anti mosquito cap, GI washout pipe and overflow pipe, 20mm ball brass valves high pressure with polythene float and flynut complete all as specified and as directed by Engr-in charge. |
| 64 | S&F 75mm bore cast iron waste and vent pipe in any length with or without ears fixed to walls with and including suitable clamps after every one mtr of interval with pig lead joints complete all as specified and as directed. |
| 65 | S&F 100mm bore cast iron waste and vent pipe in any length with or without ears fixed to walls with pig lead joints with and including suitable clamps after every one mtr of interval complete all as specified and as directed. |
| 66 | S&F CI 100mm size bends with door complete all as specified and as directed by Engineer-in-Charge. |
| 67 | S&F CI 75mm size bends with door complete all as specified and as directed by Engineer-in-Charge. |
| 68 | S&F cast iron cowl 100 mm size complete all as specified and as directed by Engineer-in-Charge. |
| 69 | S&F cast iron Nahani trap / floor trap with CP grating including jointing with pig lead joint to waste pipe of 75mm dia fixed in cement concrete (1:2:4) type B1(using 20mm graded stone aggregates) complete all as specified and as directed. |
| 70 | S&F in repairs for cast iron `P' or 'S' trap 100mm bore complete all as specified and as directed by Engineer-in-Charge. |
| 71 | S&F in repairs, salt glazed stone ware gulley traps (150mm x 150mm) size square mouthed type ‘P’ including CI cover complete all as specified and as directed. |
| 72 | S&F Vitreous china wash down water closet pan “Pedestal Pattern” coloured with WC seat cover coloured, closed pattern with flat bottom and mild steel chromium plated or aluminized hinging device including PVC flush pipe and joints etc and connection to drain, flushing pipe, anti- syphonage pipe, and fixing arrangements with fixing bolts CP Health Faucet with 1.5 mtr tube & Hook of selected etc complete all as specified and as directed. |
| 73 | S&F in repair PVC valveless, syphonic action type, flushing cistern (Twin fush type), low level 10 ltr capacity, white, with inlet, ball valve, float and handle including brackets complete all as specified and as directed by Engineer-in-Charge. |
| 74 | S&F vitreous china wash hand basin coloured of oval tiffany shape minimum of size 550mm x 400mm, bottle trap chromium plated heavy duty 32 mm dia, PVC connection of 15mm dia & 450mm long with PTMT nuts, 15mm bore basin mixer long swan neck cast copper alloy chromium plated high pressure and 32mm dia CP brass waste fitting complete all as specified and as directed. |
| 75 | M&L for granite (of any type) work (table rubbed and polished) 20mm thick as in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including cutting for hole, rounding of edges and mirror polishing over and including 15mm thick screed bed in CM (1:4) complete all as specified and as directed by Engineer-in-Charge. Note:- (a) Unit rates includes for necessary raking, circular cutting or notching and waste on Granite.(b) This item shall be used in cooking platfom counter top etc. |
| 76 | S&F PVC Bothroom mirror cabinet of size (355mm x 455mm) of selected quality glass mounted chromium plated brass screws and cup washers complete all as specified and as directed by Engineer-in-Charge. |
| 77 | S&F in repair PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and as directed by Engineer-in-Charge. |
| 78 | S&F 15 mm bore CP concealed stop cock long shank and long threading chromium plated of screwed down to iron pipes, high pressure complete all as specified and as directed. |
| 79 | S&F 15mm bore cast copper alloy CP angular valve (fancy type), screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union complete all as specified and as directed. |
| 80 | S&F in repairs 15mm size long body bib tap (half turn) CP fancy type, cast copper alloy with capstan heads screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed by Engineer-in-Charge. |
| 81 | S&F sinks with drainage board made of stainless steel 1mm thick in kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size (495mm x 420mm) bowl size (410mm x 330mm x 160mm) including PVC wate pipe of 32mm dia of suitable length, PVC connection of 15mm dia and 450mm long with PTMT nuts, 15mm bore sink mixer long swan neck CP high pressure and 32mm dia brass waste fittings complete all as specified and as directed by Engineer-in-Charge. |
| 82 | S&F brass chromium plated, tubular towel rails 20mm dia, D type, 60cm long between flanges complete all as specified and as directed. |
| 83 | S&F CP shower roses with CP arms, 15mm bore complete all as specified and as directed by Engineer-in-Charge. |
| 84 | S&F tubular towel rails, CP 20mm dia, D type, 90cm long between flanges fixed with chromium plated brass screw and plastic cleat complete all as specified and as directed. |
| 85 | S&F CP stop valve of cast copper alloy screwed down, high pressure with capstan heads, screwed both ends for iron pipe or for unions and fixed 15 mm bore complete all as specified and as directed by Engineer-in-Charge. |
| 86 | S&F PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and as directed by Engineer-in-Charge. |
| 87 | S&F soap dish, brass CP any type, fixed to plugs with chromium plated brass screws complete all as specified and as directed by Engineer-in-Charge. |
| 88 | S&F corner glass double shelf with brass CP fancy type frame and brackets of size (250 x 250)mm and 8mm thick of selected quality glass complete all as specified and as directed. |
| 89 | S&F 60 cm long glass shelf assembly consisting of 5.50 mm thick glass shelf 12 cm wide with chromium plated bracket guards and railing screws complete all as specified and as directed. |
| 90 | S&F 600mm x 450mm bevelled edge mirror of selected quality glass mounted on 6 mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and as directed by Engineer-in-Charge. |
| 91 | M&L for 75 mm thick PCC (1:4:8) type D2 (using 40mm graded stone aggregate) as in sub base, surface finished even and fair including necessary use and waste of form work complete all as specified and as directed. |
| 92 | S&F precast cement concrete machine pressed chequered tiles 25mm thick of size 300mm x 300mm, glossy finish, set and jointed with grey cement and pointed with colour cement to match with and including over 15mm thick screed bed in CM (1:6) complete all as specified and as directed by Engineer-in-Charge. |
| 93 | M&L for Durastone vitrified coloured tiles, light shade 10mm thick, area of each tile exc 0.06 sqm but n exc 0.36 sqm as in floor, set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match the colour of the tiles, over and including 15mm thick screed of cement mortar (1:6) complete all as specified and as directed. |
| 94 | S&F mild steel framed work such as grills, gratings etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders framed, balusters, walk ways, railings, frame work of water tanks and similar work conforming to Fe-410-0 or Fe 310-0 and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed. |
| 95 | Excavating post holes or similar holes, each not exceeding 0.5 cum, getting out in soft/ loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm thick, watering and removing surplus soil to a distance n. exc 50m & making good surface complete all as specified and as directed. |
| 96 | M&L for cement concrete (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) as in foundation, filling and mass concrete complete all as specified and as directed. |
| 97 | S&F for mild steel angles/rectangular hollow section/steel tubular roof trusses (framed), purlines crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. complete all as specified, including and over applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed. |
| 98 | M&L for mild steel works (Fe-290 Grade E-165) as in posts and struts etc as in fencing of angle or other sections, including cutting tops to shape as directed, drilling holes, notching for wire etc, including applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed. |
| 99 | S&F plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment including applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed. |
| 100 | M&L for mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 30cm long and 11 to 15mm diameter of neck etc complete all as specified and as directed. |
| 101 | S&F pre-painted coloured galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering / chhajja / cladding to the wall, fixed with self tapping screws/ J hook complete all as specified and as directed. |
| 102 | Surface excavation n. exc 30cm deep and average 15cm and getting out in soft/loose soil complete all as specified and as directed. |
| 103 | M&L for hardcore of gauge not exc. 63mm, deposited, spread and levelled in layers not exc.15cm thick including watering and ramming upto a true surface complete all as specified and as directed. |
| 104 | Providing and laying 60mm thick glossy finish factory made chamfered edge cement concrete coloured paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc. of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/laying of interlocking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed. |
| 105 | M&L for factory made kerb or mud stop rounded or champhered on edge with cement concrete type B1 (1:2:4), shape and size as approved complete all as specified and as directed. |
| 106 | Material and labour for point wiring with single core PVC sheathed 1100 volt grade cable with multi stranded copper conductor of size 1.5 sqmm FRLSH (Nominal area) drawn through non metallic rigid PVC conduit medium duty ISI marked not less than 20mm dia, with GI saddles GI screws, rawl plugs (concealed conduit/surface wiring in walls or roof ) including Tee, Junction boxes and proper fixing of modular switches sockets and regulators and drawing continuous earth wire with and including PVC sheathed 1100 Volts grade cable with stranded copper conductor of size 1.5 sqmm (nominal area) FRLSH and connected to main earth dolly complete for following all as specified and directed by Engr-in-Charge:- (a) One light point / fan point controlled by one switch one way |
| 107 | (c ) One 3 pin 5 Amps socket out let point on the same board controlled by one switch complete. |
| 108 | (d) One socket outlet 5 Amp controlled by one switch on independent board. |
| 109 | Description all as per Srl item No 106.00 here-in-before but for one power point 6 pin 15 Amps socket out let with 2.5 sqmm stranded copper conductor cable PVC insulated FRLSH including earth wire 2.5 sqmm copper FRLSH conductor cable connected to earth dolly complete all as specified and as directed. |
| 110 | S&F switch modular colourful white / black / golden etc 1 way 6 amps suitable for 240 volt AC complete all as specified and as directed by Engineer-in-Charge. |
| 111 | S&F switch modular 1 way 16 amps suitable for 240 volt AC complete all as specified and as directed by Engineer-in-Charge. |
| 112 | S&F socket modular 6 amps 2/3 pin combined 2 module suitable for 240 volt AC complete all as specified and as directed by Engineer-in-Charge. |
| 113 | S&F socket modular 6/16 amps 2/3 pin combined 2 module suitable for 240 volt AC complete all as specified and as directed by Engineer-in-Charge. |
| 114 | Supply and fixing for ceiling rose, surface type, 65mm x 50mm, 2 to 3 terminal complete all as specified and as directed by Engr-in-Charge. |
| 115 | Supply and fixing for lamp holder, PVC/polycarbonate type, insulated body with back plate of batten fitting with and including LED bulb 9 watt complete all as specified and as directed by Engr-in-Charge. |
| 116 | Supply and fixing lamp 9 watt fixed in pendent holder / bulk head fittings complete all as specified and as directed by Engr-in-Charge. |
| 117 | S&F exhaust fan with steel body heavy duty with louvers complete of sweep size 300mm, 1350 RPM, copper winding single phase motor, with nuts, bolts and washers, size of the bolt 15 cm long 12mm dia embedded in the wall including provision of PVC flexible copper conductor wire of size 23/0.0076 three core from ceiling rose to exhaust fan upto 1.5 mtr length for giving connection alongwith old unserviceable exhaust fan deposited to MES store yard complete all as specified and as directed. Make:- Crompton/Bajaj/Orient/Havells |
| 118 | Supply and fixing ceiling fans complete with blades, down rods, fan regulator suitable for BLDC fan and accessories, 230 V, 1200 mm sweep, min air delivery 210 CFM with service value 6 BEE and five star rated with brushless direct current motor (BLDC) including provision of PVC flexible copper conductor wire of size 23/0.0076 three core from ceiling rose to fan upto 1 mtr length for giving connection complete all as specified and as directed. |
| 119 | S&F environment friendly indoor decorative 20 watt LED for wall mounted 20 watt LED batten extruded aluminium heat sink provided for heat dissipation and integrated driver back plate suitable for batten fittings complete all as specified and as directed by Engr-in-Charge. |
| 120 | S&F environment friendly indoor decorative mirror LED light fittings 1 x 10 watt with opal diffuser including all accessories suitable for batten fittings complete all as specified and as directed. |
| 121 | Supply and fixing sheet metal enclosure for distribution board SPN (when MCBs to be used ) 8 way double door, 200 Amps rated bus bars and with neutral, earthing bar and din rail complete all as specified and as directed by Engr-in-Charge. |
| 122 | Supply and fixing MCB, SPN, 40-63 Amp, 10 kA complete all as specified and as directed by Engr-in-Charge. |
| 123 | Supply and fixing MCB, SP, 6-32 Amp, 10 kA complete all as specified and as directed by Engr-in-Charge. |
| 124 | M&L in replacement submain wiring with two run of 4 sqmm single core PVC insulated but unsheathed FRLS cable of specified size of multistranded copper conductor 1100 volts grade IS:694 marked and one run of 4 sqmm PVC insulated but unsheathed FRLS cable for earth continuity conductor drawn through and under suitable size of rigid non metallic PVC conduit, medium grade, ISI marked ( not less than 20 mm dia) complete with all acessories and fittings all laid/fixed concealed in wall/ceiling or surface in wall and surface conduit on ceiling, and also include the specified runs of specified size earth continuity conductor of similar type cable complete all as specified. Note:- 2 Runs of 4 Sqmm single core and one run of 4 sqmm single core cable shall be measured 1 RM. |
| 125 | Supply and fixing electric water heater, storage type ABS body type with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostat, NRV, connection piece etc including steel braided flexible connection for pipe of size 15mm bore with GI hexagonal adopters/Nuts on both sides for inlet (cold water supply) and out let (hot water supply), provision of wall mounting arrangement, mounted on wall with suitable size of anchor bolts, making connection including testing complete all as specified and as directed. |
| 126 | Supply and fixing in replacement of sheet metal enclosure single pole and neutral with a two pin and earth plug and socket complete with one single pole MCB 20-32 amps complete all as specified and as directed by Engr-in-Charge. |
| 127 | M&L for earthing complete for bldg with galvanized mild steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 meters below ground level) with top edge of earth plate not less than 1.5 metres below ground level connected to galvanized earth wire 4.00 mm dia by means of nuts, bolts, thimbles, check nuts, washers of GI or steel, PCC (concrete chamber of size 300mm x 300mm x 300mm inside dimension) shall be PCC (1:3:6) type C-1 (using 20mm graded crushed stone aggregate) with fair finish, internal surface of concrete chamber shall be given 15mm thick plaster in CM (1:4), funnel with wire gauge of 22 gauge, 8 mesh per liner inch, 80 mm thick PCC pit cover of size 320mm x 320mm of RCC (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) reinforced with XPM, JALLI and charcoal dust and common salt all as shown in electrical plate No 3 of MES SSR Part-I (2009) and specified including provision of earth wire protected by 15mm dia medium grade GI pipe and watering GI pipe shall be 20mm bore medium grade etc complete, all excavation and earth work & connecting the earthing to an earthing test point main switch board as specified and testing on completion complete all as specified & as directed by Engr-in-Charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 01, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 22, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 6 daysAug 29, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 13 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender