Tender For Repair/Maint Of Misc Work From East Gate To Kolkata Gate Outside Vijay Durg Under Ge(Fw) Kolkata
Tender Value
29.50 Lakhs
Estimated cost
Bid Submission
22 Aug 2026
12 days left
EMD
59000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Kolkata → West Bengal
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair/Maint Of Misc Work From East Gate To Kolkata Gate Outside Vijay Durg Under Ge(Fw) Kolkata
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for, all as specified and as directed by the Engineer-in-Charge. |
| 2 | Demolition of stone slabs and tiles of any description or thickness in floors/vertical surfaces, etc laid, bedded and pointed in any mortar, etc complete all as specifed and directed by Engineer-in-charge. |
| 3 | Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings all as specified and directed. |
| 4 | Demolition of Brick Work built in Cement Mortar including all Quoins, Arches, Pillars, etc. of any descriptions, complete all as specified and as directed. |
| 5 | Dismantling posts or struts (wood,steel,or RCC) any section ,including taking out embedded portion and making good disturbed ground post embedded in concrete, complete all as specified and as directed. |
| 6 | Dismantling of fencing,wire mesh any type complete all directed . |
| 7 | Dismantling wrought iron or mild steel of any description not otherswise provide for , etc complete all as specified and as directed. |
| 8 | Dismantling barbed wire fencing of any description complete all as directed |
| 9 | Dismatling structural steel work including doors , gates but excluding trusses etc complete all as specified and as directed. |
| 10 | M&L for brick work with flyash bricks straight on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed. |
| 11 | S&F in repair 25mm thick precast cement concrete Type B-0 (1:2:4) (using 12.5 mm graded crushed stone aggregate) louvers and jallies including all moulding, but excluding frame set in cement morter 1:4 as in repair, complete all as specified and as directed. |
| 12 | Taking down cement plaster on brick or concrete surfaces including racking out joints hacking for key, scrubbing down with water etc complete all as specified and as directed.(Note: The cost includes any thickness found during execution increased due overleaping of n no of layers of plaster , tiles, mosiac finish with out any cost to govt exchequer) |
| 13 | M&L for Rendering 15 mm thick in cement mortar (1:4) on Brick/Concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.Note:- No extra cost shall be claimed by contractor in respect of formwork and at any height incl scafolding and site where plaster is to be executed and same shall be executed in Patches) |
| 14 | M&L for Rendering 10 mm thick in cement mortar (1:6) on brick masonary or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed (Note:- No extra cost shall be claimed by contractor in respect of formwork and at any height incl scafolding and site where plaster is to be executed and same shall be executed in Patches) |
| 15 | M&L for Rendering 10 mm thick in cement mortar(1:3) on ceiling, finished even and smooth without using extra cement complete all as specified and directed..(Note:- No extra cost shall be claimed by contractor in respect of formwork,scafolding and at any height and site where plaster is to be executed.) |
| 16 | M&L for rendering 10 mm thick in cement mortar 1:3 on concrete surface of facia, finished surface even and smooth without using extra cement, complete all as specifed and directed. Note:- (Note:- No extra cost shall be claimed by contractor in respect of formwork,scafolding and at any height and site where plaster is to be executed.) |
| 17 | Excavation in post holes (or similar holes) each n exc 0.5 Cum getting out, returning filling in and ramming earth or broken rubble mixed with earh around in layer n exc 25cm watering & removing surplus soil to a distance n exc 50m & making good surface in soft/loose soil, complete all as speciified. |
| 18 | M&L providing cement concrete type B-2 1:2:4 (40 mm graded agg) in foundation ,filling and mass concrete as in posts complete all as specified and as directed. |
| 19 | Returning filling and ramming in layers n.exc 25cm deep as in soil complete all as specified. |
| 20 | Removal of excavated soil to a distance nexc 50m and spreading along road side berms as spfd and directed by Eng-in-charge |
| 21 | S&F Mild steel angle iron section as in posts struts work in fencing including cutting tops to shape as diredcted,drilling holes, notching for wire,etc ,flat iron fillets for securing wire mesh etc,including all necessary drilling,bolting or riveting,etc and similar work conforming to Fe 290 Gde E-165 complete all as specified & directed. |
| 22 | S & F 4 mm dia PVC coated galvanised mild steel chain link fencing of mesh size 50 x 50 mm fixed with straining bolts including line wire any mesh size and type to any type of standarads, rails,straining bolts etc. including provision of binding wire, complete all as specified and as directed. |
| 23 | Mild steel round bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (Annealed) not less than 0.90 mm dia or securing with clips quality conforming to Fe-410-W (Gde.E-250) quality-A or Fe 290 (Gde -E-165) complete all as specified and as directed. |
| 24 | S&F MS flat iron 40x6 to secure chain link fencing all as specified and directed conforming to Fe 410-(Gde-E-250) quality complete all as specified and as directed. |
| 25 | S &F MS screw bolt (machine made with hexagonal or square head at one end and screwed the other end with washers 12 mm dia and n exc 5 cm long ) complete as specified & directed. |
| 26 | S&F in Galvanised 2 strand steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacing and straining and fixing any type of standard rails straining bolts incl securing or tying at crossing with and provn of Galvanised MS wire, staples or steel pins, as directed (each line wire to be measured) complete all as specified.. |
| 27 | Fixing only barbed wire obtained from dismantling complete all as specified and as directed. |
| 28 | S&F in repairs anti-rust concertina coil (reinforced punched barbed tape single layer) for fencing work incl taking down existing coils complete all as per following specifications :-(i) Diameter of concertina coil - 750 mm dia (before stretch)(ii) Number of turns in concertina - 50 turns(iii) Weight of each coil - 10.5 KG(iv) Coverage per coil - 8 m(v) Central core wire - made from high tensile spring steel core wire conforming to IS-4454 duly hot dipped galvanised (conforming to IS-2629) with diameter 2.59 mm + 0.05 mm, UTS 145-160 kg/sqmm, zinc coating 250-300 grams/sqm(vi) Strip - Electro galvanised steel strip 0.5 mm + 0.02 mm thick, width 19 mm (before wrapping on central core wire) conforming to IS-1573, zinc coating - 120 gram/sqm and bituminised dipped, width of barbs 11.5 mm, pitch of barbs 25.4 mm+ 0.2 mm(vii) Clips - AISI 304-1.5 mm thick 'C' & 'U' clips. 'C' special type for fixing coil and RBT wire, 'U' clips special type for joining one coil to another coil and RBT wire to RBT wire joining.(viii) No. of clips - minimum 125 for each coil(ix) Handle and spikes to be provided as required(NOTE : 1. The concertina coil shall be given additional primer treatment of epoxy/ polyurethane and final paint top coat of caufiled green shade (BSL 139) by hot dipping process.2. RBT wire for fixing of concertina coil will be measured and paid separately.3. Running length of the wall shall be measured for payment purpose. |
| 29 | S&F Mild steel work in framed work such as in doors or gates grills, gratings,framed guard bars,ladders etc with ends of bars shouldered and/or riveted or forged into spikes and similar work confirming to Fe-410-O as in framed and hung gates including pintle hinges,stops,hand made sliding bolts etc and similar work confirming to Fe-410-W complete all as specified and directed. |
| 30 | M&L for Cement concrete 1:2:4, type B1 (using 20mm graded stone aggregate) in copings,kneelers, Apex stones, benchings, rounded or chamfered on edges complete all as specified and directed. |
| 31 | M&L Cement concrete type B-2, 1:2:4 (40 mm graded aggregate) 100 mm thick as in Floors /path laid in alternate pannels finished even and smooth without using extra cement as specified and as directed (note-no extra cost shall be claimed by contractor for use of vibrator ) |
| 32 | M&L for 25 mm thick in cement concrete type B-1, 1:2:4 (20mm graded aggregate) finished without using extra cement all as specified as directed. |
| 33 | M&L for 25 mm thick sand filling under floors or in foundtion including watering and consolidation for laying inter locking tiles complete all as specified and as directed. |
| 34 | M&L 75m m thick PCC (1:4:8) type D-2 using 40mm stone coarse aggregate as in sub base of flooring and path, etccomplete all as specified and as directed. |
| 35 | Supply and fixing 25mm thick pre-polished coloured chequered concrete tiles of size 300mmx300mm, as in flooring over 20mm thick backing layer of cement mortar (1:6) set and jointed in neat cement slurry and pointed in white cement mixed with admixture pigment to match the shade, as directed. |
| 36 | M&L for 25 mm thick pre polished coloured chequred tiles of size 400X400/450x450 jointed and pointed in neat cement slurry with white or coloured to match including over 20 mm thick screed bed CM 1:6 completed all as directed. |
| 37 | Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed. |
| 38 | Refixing of Machine pressed precast concrete interlocking paver block of any shape and size, 60 mm thick in path and hardstanding all as specified and directed. Note-dismantled tiles obtained from item no.04 are used for refixing. no extra cost shall be claimed by contractor and sand cushioning measured in respective item of 25 mm sand cushioning complete all as specified and as directed. |
| 39 | Providing and laying 80 mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed. |
| 40 | Refixing of Machine pressed precast concrete interlocking paver block of any shape and size, 80 mm thick in path and hardstanding all as specified and directed. Note-dismantled tiles obtained from item no.04 are used for refixing. no extra cost shall be claimed by contractor and sand cushioning measured in respective item of 25 mm sand cushioning |
| 41 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and as directed. |
| 42 | Supply and fixing 8-10mm thick endure tiles of size 300mmx300mm, as in flooring over 20mm thick backing layer of cement mortar (1:6) set and jointed in neat cement slurry and pointed in white cement mixed with admixture pigment to match the shade, as directed by Engineer-in-Charge. |
| 43 | S&F 15mm thick pre-polished decorative cement concrete tree gaurd tiles of approved size, design and colour laid on vertical surfaces over 15mm thick backing layer in cement mortar (1:4) set and jointed in neat cement slurry and pointed in white cement mixed with admixture of pigment to match the shade complete all as specified and as directed. |
| 44 | M&L for 20mm thick coloured granite ,machine cut as in vertical surfaces such as skirting/dado over 10mm thick backing layer in cement mortar (1:3) , set and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite tile including rubbing and polishing complete all as specified and as directed. |
| 45 | M&L for Machine cut Kota stone slab flooring 20-25mm thick, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, laid on floor over and including 20mm thick backing layer in cement mortar (1:6) complete all as specified and as directed. |
| 46 | Material and labour for grinding/polishing and cutting to existing stone floor of any description (such as kota stone, marble stone, terrazo,granite and similar surfaces etc) cleaning with water and applying zinc oxide powder complete all as specified and as directed. |
| 47 | Removal and desposal of waste material/debries/sludges/soil from any location at FW camp area to out of MOD Land. complete all as specified and as directed by Engr-in-charge. Note : Volume of each tipper/ Job should not be less than 4 cum complete all as specified and as directed. |
| 48 | M&L Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified. |
| 49 | M&L Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified. |
| 50 | Material and labour preparation of old brick/stone/concrete wall surfaces of any description over 10cm width or girth and applying one coat of synthetic enemal paint complete all as specified and as directed. |
| 51 | M & L for preparing bituminous surfaces of road and marking 2.5mm thick centre lines, stop lines, dashes, arrows etc. and the like n. exc 10cm wide on roads pavements with hot applied thermo plastic road marking paint of approved colour confirming to BS 3262-1989 with special applicator machine all as per manufacturers instruction complete all as specified and directed |
| 52 | Material and Labour for applying 1.0 mm thick wall putty on old/new surface of wall and complete all as directed. |
| 53 | Material & Labour Preparation of new plaster surface of walls applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and except priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over all as specified and directed. (Note) :- 1. weather coat colour as per site requirment., 2.Any height of building including scaffolding etc(up to any high of building) |
| 54 | Material & Labour complete removal of old surface of walls applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over all as specified and directed.( any height of bldg ) |
| 55 | Material & Labour preparation of old surface of walls applying one coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and except priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over all as specified and directed. (Note) :- 1. weather coat colour as per site requirment., 2.Any height of building including scaffolding etc(up to any high of building) |
| 56 | Material & Labour complete removal of old surface of walls applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and Except priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over all as specified and directed. Note :- 1. weather coat colour as per site requirment.2.Any height of building including scaffolding etc |
| 57 | M&L for preparation of newly plastered surfaces on ceiling and applying two coats of oil emulsion distemper complete all as specified and directed. |
| 58 | M&L preparation of old decorated plastered surface of walls and applying one coats of oil bound distemper complete all as specified and directed.. |
| 59 | M&L preparation of new plastered surface of walls and applying two coats of oil bound distemper complete all as specified and directed. |
| 60 | M&L for preparation New steel and iron surfaces apply two coat of synthetic enamel paint over one coat priming with red oxide of any description, over 10cm in width or girth,not otherwise described complete all as specified and directed any height of bldg . note: colour should be approval of user requirment. |
| 61 | M&L for preparation old steel and iron surfaces apply two coat of synthetic enamel paint over one coat priming with red oxide of any description, over 10cm in width or girth,not otherwise described complete all as specified and directed any height of bldg . note: colour should be approval of user requirment. |
| 62 | Note: Schedule of credit (SCHEDULE OF CREDIT) amount of Rs ________ mentioned on Page No ____ shall be deducted from the total quoted amount of BOQ. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 01, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 22, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 12 daysAug 24, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 14 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender