Tender For special Repair To Operation Work Shelter Number 5117/N1 And 5117 /N2 (Single Offr Accn) Of 301 Army Avn Sqn (Spl Ops) And Provn And Installation Of Lightening Arrestors Alongwith Allied Works At Tx Nfs Node Mil Stn Haldwani At Under Ge R
Tender Value
10.92 Lakhs
Estimated cost
Bid Submission
24 Aug 2026
18 days left
EMD
21900
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Nainital → Uttarakhand
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repair To Operation Work Shelter Number 5117/N1 And 5117 /N2 (Single Offr Accn) Of 301 Army Avn Sqn (Spl Ops) And Provn And Installation Of Lightening Arrestors Alongwith Allied Works At Tx Nfs Node Mil Stn Haldwani At Under Ge Ranikhet
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete in but of any description and in any position not other wise specifically provided for complete all as specified and directed. |
| 2 | Dismantling floor, hearth, wall tiling including taking down plastering in cement mortor removing serviceable tiles to store and rubbish off the premises complete all as specified and directed |
| 3 | M&L for 25mm thick PCC 1:2:4 type B-0 (12.5mm graded stone aggregate) as in level course with finshining in cement concrete surface even and rough to receive screed bed complete |
| 4 | M&L Joint free Non - skid coloured ceramic tiles 7 to 10 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry over screed bed of 15 mm thick 1:6 and pointed in white or coloured cement to match complete. |
| 5 | S&F in repairs parquet flooring 8.3 mm thick hard board plank both side laminated with decorative surface and approved by GE laid above the thermoplastic sheet complete all as specified |
| 6 | S&F in repair Prayag hanging system and clamps support and holes with screws and back support rectangular mirror cabinet 400 X 500 (Cat No. 554) and fixed to plug with screws and cup washers complete all as apecified & directed |
| 7 | Supply and Fixing in repair Laying CPVC Water Tubing 15mm dia (Bore), with all Fittings, fixed on Walls, Ceiling or laid in Floors or any other Situation, sealing joints with solvent and making good, complete as all specified and as directed. |
| 8 | Supply and Fixing in repair Laying CPVC Water Tubing 20mm dia (Bore), with all Fittings, fixed on Walls, Ceiling or laid in Floors or any other Situation, sealing joints with solvent and making good, complete as all specified and as directed. |
| 9 | S&F in repair 15mm dia bib taps long body CP Brass with Capstanhead, screwed down, screwed for iron pipe of bore 15mm complete. |
| 10 | S&F in repair brass 15mm Chromium plated Basin Mixer swan neck valve hot and cold screwed down for iron pipe complete. |
| 11 | S&F in repair Angle Cock,15mm fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed. |
| 12 | S&F in repair Brass chromium plated shower rose 125mm size with 225 mm Flange, swivel joints, including fixing to steel pipe or union complete all as specified and directed. |
| 13 | S&F in repair Tubular towel Rail CP Brass, chromium plated D type with CP Brackets, 600 mm long between flanges all as specified. |
| 14 | S&F in repair Glass shelf 450 x 125 x 6MM (with ABS Bracket chromium plated bracket guard and SS railing complete all as specified and as directed |
| 15 | S&F in repair Soap Dish Stainless Steel complete all as specified & directed. |
| 16 | S&F in repair Peg Set of 6 Stainless Steel as approved by Engr-in-Charge |
| 17 | S&F in repair Corner Glass Shelf 300mm (with ABS Brackets) 300 x 600mm as approved by Engr-in-Charge |
| 18 | S&F in repair Brass CP Wall mixer for mixing hot & cold water (3 in 1) screwed down for iron pipe and fixed bore of pipe 15mm complete all as specified |
| 19 | S&F in repair Towel Ring including necessary stain less steel screws, rawl plugs and washers complete all as specified and directed. |
| 20 | S&F in repair PVC Connections 15mm size with PTMT Nuts of length 600mm and fixed, complete all as specified and as directed. |
| 21 | Taking down chowkats or frames n.exc 1.50 sqm each with shutters (without taking off shutters from the frames) complete. |
| 22 | Taking down chowkats or frames exc 1.50 sqm but n.exc 4.00sqm each with shutters (without taking off shutters from the frames) complete. |
| 23 | S&F powder coated Anodised aluminium frame for doors, windows ventilators with one or more rebates including joining cleat for fixing etc. complete shall as specified. |
| 24 | S&F powder coated aluminium Anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, ruber neoprene packing,handles 2 Nos in each door, hinges,anodised aluminum snap beading screws etc. complete all as specified |
| 25 | S&F powder coated aluminium Anodised aluminium door shutters ready to recieve wire mesh/glass, aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, ruber neoprene packing,handles 2 Nos in each door, hinges,anodised aluminum snap beading screws etc. complete all as specified |
| 26 | S&F Aluminium alloy, anodised, sliding door bolt with haps, staple (bolt type) and fixing clips with sheet, cast and extruded section and fixing bolt and sliding bolt of extuded sections or cast aluminium alloy and fixed 300 mm long complete. |
| 27 | S&F 150 mm overall length floor stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and as directed |
| 28 | S & F 200 mm long aluminium anodized barrel tower bolts of extruded section complete all as specified and as directed. |
| 29 | Sheet glass 4.8mm thick glass and glazing in squares complete. |
| 30 | S&F aluminium two track powder coated of any colour (thickness of powder coating not less than 50 micron) sliding window with two sliding shutter the size of outer frame three track 92x31.5x1.2mm (using two track for glazed window shutter), the section shutter size 37x18x1.2mm) and glazing with 4.8mm thick glass (Plain/floated) incl allround suitable rubber gasket inserted in the frame of shutter with tracking arrangement each sliding window shall be provided with one number handle incl rocking arrangement & 2 numbers sliding rollers of nylon with incl all necessary fittings complete all as specified and directed. |
| 31 | S&F Aluminium Powder coated designer grill of 5.5 mm dia and aperture of 75 mm fixed with and including aluminium powder coated flat section of size 50 x 1.5 mm and suitable aluminium anodised frame F/H section complete all as specified and directed. |
| 32 | S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed |
| 33 | Supply & fixing PVC Fluted panel /grooved pattern of matt/glossy finish of any size and colour 8 to 25mm tMck for ceiling and wall including all fixing viz, U and L as design and pattern including all necessary framed works as per manufacturer s instruction, make as approved by GE complete all as specified and directed |
| 34 | S&F aluminium sheet powder coated of thickness not less than 5mm thick to be in sealed as panel in aluminium door including fixing complete all as specified and directed. |
| 35 | S&F in repair vanity cabinet with wash basin Owing to the high quality HDHMR Board 18-19 mm thick with a gloss/matt finish table top of size 600mm x 450mm x 150mm,any shape and colour including PVC waste pipe 32mm dia, waste coupling brass chromium plated complete all as specified and directed. |
| 36 | S&F in repair one piece floor mounted vitreous china EWC with integrated flushing cistern, soft closing seat cover and necessary nut/bolt for fixing complete all as specified and as directed by Engr-in-Charge |
| 37 | S&F in repair Decorative Stainless steel tubular curtain rail of 25mm dia incl six nos curtain ring per running mtr and one number of brackets on each end and one no of globe on each end of the rod per opening of door / window (make and materail approved by Engineer-in-charge) complete all as specified and directed. |
| 38 | M&L for two coats of synthetic enamel painting over a coat of red oxide zinc chrome primer on new steel surfaces over 10cm width or girth including preparation of surface complete. |
| 39 | M&L for one coat of synthetic enamel paint to old decorated steel surfaces of girth exc 10cm including preparation of surfaces complete all as specified and directed |
| 40 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed |
| 41 | S&F framed work such as gate, grills,gratings, etc with ends of bars shouldered and / or riveted or forged into spikes; framed guard ; barred iron doors; ladders ; framed balusters; walk ways; railing and simillar work Con-forming to Fe 290 Gde E-165. |
| 42 | S&F 20 mm thick cement fiber board incl all fittings , fixtures, screws, nuts/bolts of appropriate shape & size with mechanical means complete all as specified and directed |
| 43 | S&F 3.3 mm thick linolium sheet, plain coloured laid dry in floors incl stretching, cutting, fittings & incl sealed with an appropriate adhesive complete all as specified and directed |
| 44 | Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories &stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement. |
| 45 | Material & Labour for providing and fixing stainless steel (Grade 304) railing (except material) made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement. |
| 46 | Dismantling of wall and ceiling boards (fiber, pulp, insulation etc,) or insulation boards/slabs/blankets, any thickness including cover fillet complete all as specified and directed. |
| 47 | S & F for Aluminium anodised snap grid frame work for false ceiling comprising of following section for making partitions of 600 X 600 mm size fixed to walls with rawl plugs and screws and hang to roof with s 6 mm dia. G.I. (upto1200mm length) adjusting levelfixed to roof slabs by means of ceilling cleats made out of G.I.flat 40 x 3 mm size 60mm long and expansion hold fasteners12.5mm dia. 40mm long complete all as specified. size of main tee shall be :-(i)37mmx24mmx0.3mm thick, (ii)Cross Tee 28mmx24mmx0.3mm thick and (iii)Wall angle 24mmx24mmx0.3mm thick. |
| 48 | S & F 4 mm thick non asbestos fiber designer ceiling (E-board classic) board / tiles for insulation and accoustic purpose, 595 X 595 mm size fixed in ceiling with and including dusting of surface complete all as specified and directed |
| 49 | M&L for 2mm thick wall care putty on old plastered surfaces of wall, and apply two coat of exterior emulsion paint (Apex) over a coat of primer complete all as specified and directed |
| 50 | Taking down carefully by unscrewing from boards/ outlet boxes , fittings and fixtures such as switches , soctes, ceiling roses , lamp holders ,brackets , ceiling fittings, bulk head fittings , tube lights and regul;aters, etc for reuse at site or carrying to the store ( To be measured only when found serviceable all respects complete foe re use ) |
| 51 | Fixing only lamp holder ( modular type ) PVC insulated body with back plate for angle/battern fitting complete all as specified and directed |
| 52 | Fixing only switch piano flush type single pole, one way 5 Amp complete all as specified and directed. |
| 53 | Fixing only switch piano, flush type single pole 15 Amp complete all as specified and directed. |
| 54 | Fixing only switch piano flush type single pole, two way 5 Amp complete all as specified and directed. |
| 55 | Fixing only socket outlet 2 in 1, 3 pin, 15 Amp flush type complete all as specified and directed. |
| 56 | Fixing only socket outlet 2 in 1, 3 pin, 5 Amp flush type complete all as specified and directed. |
| 57 | Fixing only Bell push flush type , 5 amp |
| 58 | Fixing only stepped fan regulator flush type on the existing phenolic laminated sheet etc |
| 59 | Fixing only Electric Bell multi musical type AC 230 VOLTS , 50 Hz |
| 60 | Fixing only ceiling rose, PVC/ Poly carbonate, isolated body three terminal complete all as specified and directed. |
| 61 | Fixing only LED lights fitting 1x 20W (warm/milky white as required on site), 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. |
| 62 | Taking down carefully aluminium/copper wiring of any size (for light, fan, socket or power etc complete) including fixture and fittings such as switches, sockets, ceiling roses, pendent holders regulators, tube lights etc and making good disturbed surfaces of wall, roof etc to match with existing surface. |
| 63 | Supply & Fixing point wiring for one light point/ fan point controlled by one, one way switch with 1.5Sqmm size, PVC insulated and unsheathed 1100volts grade, single core stranded (multistrand) copper conductor (FRLSH) PVC cable drawn into & including medium grade PVC conduit (not less than 20mm outer dia ) with all fittings and accessories fixed concealed (including chase cutting in brick/ stone masonry walls for fixing conduit and plastering and whitewash/colouring the external surface and matching the same with existing surface) and sunk cast iron or pressed steel terminal boxes for mounting fittings like switches, sockets & fan regulators etc with 3 mm thick plastic laminated sheet covers fixed with brass screws and cup washers including one continuous run of PVC insulated (green colour) 1.5 Sqmm multistranded copper conductor cable earth wire and connected to earth dolly complete all as specified and directed (Note:- wiring shall be done in colour coding as directed by Engineer in charge. |
| 64 | All as per item No.63 herein before but one socket outlet 5 Amps on the same board. |
| 65 | All as per item No.63 herein before but one 3 pin socket outlet 5 Amps independent. |
| 66 | All as per item No. 63 above but with 2.5 Sq mm two single core and 2.5 Sq mm one single core as earth wire for 5/15 Amps socket. |
| 67 | supply & Fixing lamp holder PVC insulated body with back plate for angle/battern fitting complete all as specified and directed |
| 68 | Suppy & Fixing switch piano flush type single pole, one way 5 Amp complete all as specified and directed. |
| 69 | Supply & Fixing switch piano, flush type single pole 15 Amp complete all as specified and directed. |
| 70 | Supply & Fixing socket 15 Amp flush type complete all as specified and directed. |
| 71 | Supply & Fixing socket outlet 2 in 1, 3 pin, 5 Amp flush type complete all as specified and directed. |
| 72 | Supply & Fixing bell electric multi musical type AC 230 volts, 50 hz |
| 73 | Supply & Fixing ceiling rose surface bakelite 3 terminal with base plate |
| 74 | Material and labour for Sub main wiring with 2 run of 6 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable ISI marked, drawn in to and including Rigid non metallic PVC conduit ( ISI marked) Heavy grade, 20 mm dia (external) inclusive of junction/terminal boxes, all fittings and accessories fixed concealed with and including 6 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable ISI marked as earth wire, connected with thimble from main DB to sub main DB including cutting and chasing and making good surface as original by plastering and whitewash/ colour/ distemper etc including taking down existing old sub main wiring complete all as specified. Note :1 The cost of earth wire is included in the quoated rates. 2. Two run of 6 sqmm, one run of 6 sqmm and one run of PVC conduit will be measured as one unit ie one running metre” |
| 75 | All as per item No. 74 herein before but Sub main wiring 2 run of 4 sqmm |
| 76 | Supply and fixing LED lights fitting 1x 20W (warm/milky white as required on site), 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose and life of tube light not less than 50,000 hours.complete all as specified and directed..Make Havells cat pat LUMILINEBS20WLED865SPCWH or equivalent of phillips/wippro/Bajaj/Surya complete Note:- LED tube light shall be purches to get minimum 2 year warrenty of material from manufracturer. |
| 77 | Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible opper conductor cable of suitable size complete |
| 78 | Supply & Fixing sheet metal enclosure for DBs(double door type) single pole and neutral 8 way including blanking plate as required with 200 Amps rated bus bar, 240 volts fixed complete all as specified and directed . |
| 79 | Supply & Fixing 240V, 10KA 'C' curve miniature circuit breaker (MCB) of SPN 40 to 63 Amp and current carrying capacity in the DB complete with connection testing and commissioning complete all as specified and directed . |
| 80 | Supply & Fixing 240V, 10KA 'B' curve miniature circuit breaker (MCB) of single pole 5 to 32 Amp and current carrying capacity in the DB complete with connection testing and commissioning complete all as specified and directed . |
| 81 | Supply and Fixing propeller type AC ventilating fans 230 volts, 50 C/S heavy duty 1400 RPM, 300 mm sweep (Exhaust fan) metal body and blades protected by metal guards,Bird guard for safetry,two sleeves bearings, complete including the ragged bolts in wall, fixing the frame on the exhaust side (outer surface of the wall) and connecting with and including PVC insulated three core white 23/.0076 copper cable, rubber insulated from ceiling rose to exhaust fan motor complete all as specified and directed. |
| 82 | Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories (incl ceiling clamp/hook fixing in ceiling/roof with fashner/nut & bolts), 230 V, 1200 mm sweep, Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC)complete all as specified and directed by Engineer-in-Charge. |
| 83 | S & F LED light fitting 1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size. Make : Havells cat pat HEXAFT10WLED857SSYMBOPC or equivalent cat part in make phillips/wippro/Bajaj & C&S . Note:- Contractor shall submit 2 year warrenty of material from manufracturer alongwith purchase voucher. |
| 84 | Supply and fix water heater storage type electric supplied and installed complete steel body and heating element upto 2 KW of capacity 25 ltrs, BEE 5 Star rated including making connection with industrical socket, ultra thick SS inner tank of superior 304 grade, Fire retardant ISI Mark supply cord, Rust & shock proof ABS body, Compact & easy to install and proper hanging on nut bolts washers grouted on wall and PVC pipe for connection of hot and cold water complete all as specified and directed by Engr-in-charge. |
| 85 | Supply,fix and connecteing,Air termination, single pointed, copper rod 12mm dia and 300mm long complete with nacessary pcc foundation and as directed. |
| 86 | Test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 nos. 8mm dia 25mm longhex. head screw complete all as specified and directed. |
| 87 | M&L Copper strip 20 x 3.15mm with saddles and fixing screws etc. for roof conductors and down conductors above ground complete all as specified and directed. |
| 88 | M&L for Earthing complete with Coppert earth plate electrodes 60x60x6.3 mm thick buried directly in ground (earth pit not less than 2. 25mtr deep below ground level) with top edge of plat not less than 1.5 mtr below normal ground level connected to copper strip 25 x 3 mm as earthing lead by means of bolts, nuts , check nuts and washers of galvanized iron or steel all as shown in electrical plate No 3 and including excavation and earth work, GI pipe light grade of suitable dia,supplying and laying charcoal dust, common salt, PCC 1:2:4 type B1 chamber and MS angle iron frame 40x40x3mm and RCC cover 40mm thick (1:2:4) type B1 using 20mm graded stone aggregate reinforced with 6 mm dia TMT bars @ 75mm C/C both ways with MS handle 12mm dia, PGI funnel and wire mesh,20 mm dia GI pipe light grade for watering and connected to earth test point and testing complete all as specified and directed by Engr-in-Charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 03, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 24, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 18 daysAug 31, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 25 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender