Tender For One Panchayath One Playground -Development Of Jai Hind Stadium In Njarackal Grama Panchayath In Vypin Lac, Ernakulam District-Supply And Installation Of Open Gym Equipment - Retender
Tender Value
2.25 Lakhs
Estimated cost
Bid Submission
11 Aug 2026
4 days left
EMD
5640
Bank guarantee accepted
Document Fee
590
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Thiruvananthapuram → Kerala
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for One Panchayath One Playground -Development Of Jai Hind Stadium In Njarackal Grama Panchayath In Vypin Lac, Ernakulam District-Supply And Installation Of Open Gym Equipment - Retender
BOQ
| Sl. No. | Item Description |
| 1 | Outdoor Gym Equipments |
| 2 | OD268048/2025-2026 Chest Press (Double) - Supply and Installation of Double Chest Press having the following specifications: Dimensions: (L X W X H) 1955 x 710 x 1900 mm. Main center pipe - Ø 114 mm OD “B” class GI pipe. Foundation plate –M.S. round plate of Ø 250mm & 8 mm thick. Foundations cover capdome shape of PP / NYLON / HDPE material. Remaining frame -made up of Ø 48 mm OD “B” Class G.I. pipe. Handle - Made up of Ø48mm OD “B” Class G.I. pipe. Link - made up of Ø 48 mm OD “B” Class G.I. pipe. Seat & back rest – 380 X 275 X 60 mm thick high-density polyethylene (HDPE) blow molded with M10 in-sert wall thickness 3 to 4 mm. Bearing bush Closing cap’s– PP / NYLON / HDPE material. Handle must be connected with frame by 8 MM laser cutting MS profile. Top Closing cap – dome shape made by PP / NYLON / HDPE material. Foundation stool: Made from main pipe Ø 88 mm OD M.S pipe and top support of M.S. round plate of Ø 250 mm & 8 mm thickness is welded top. Square tube of 30 x 30 x 2 mm must be used to support center pipe.Height of stool is 3 ft. Foundation stool is embedded in C.C. stock below ground level. Bearing - Use is 6005 permanent lubricated reputed brands. Pin – Made up of Ø 25 mm M.S. bright bar pin. Bearing bushes - Ø 60 mm OD seamless pipe. Grips - High quality rubber Ø 46 mm OD. Circlips–A 24 circlips are used for assembly. Coating - best quality of powder coating 80-120 micron. Safety Instructions and Exercise chart - start & finish position stick on product. All joints must be welded as per IS standards and zinc primer paint should be applied at all the welding points prior to finishing. (Foundation shall be M20 CC and design shall be approved by the Engineer-in -charge before installation.) |
| 3 | OD268050/2025-2026 Air Walker - Supply and Installation of Air Walker having the following specifications: Dimensions: (L X W X H) 1190 x 380 x 1244 mm. Main Frame- Ø 88 mm OD ?B? class GI pipe dually bending design. Foundation plate?M.S. round plate of Ø 250 mm & 8 mm thick. Paddle? Ø 42 mm OD round GI pipe. Handle ? Ø 33 mm OD ?B? class GI pipe. Footrest - cast iron 124 x 296 x 5 mm thick and M.S. plate of 2 mm thick use to support it. Top Closing cap ? dome shape made by PP / NYLON / HDPE material. Closing cap?s -PP / NYLON / HDPE material. Bracket - 8 mm thick laser profile is use to support paddle frame. Foundation stool: Made from main pipe Ø 88 mm OD M.S pipe and top support of M.S. round plate of Ø 250 mm & 8 mm thickness is welded top. Square tube of 30 x 30 x 2 mm must be used to support center pipe.Height of stool is 3 ft. Foundation stool is embedded in C.C. stock below ground level. Bearing- use is 6005 permanent lubricated reputed brands. Pin?s ? Ø 25mm M.S. bright bar pin. Circlips? A 24 circlips are used for assembly. Bearing bushes -Ø 60 mm OD seamless pipe. Coating - best quality of powder coating 80-120 micron. Safety Instructions and Exercise chart - start & finish position stick on product. All joints must be welded as per IS standards and zinc primer paint should be applied at all the welding points prior to finishing. (Foundation shall be M20 CC and design shall be approved by the Engineer-in -charge before installation.) |
| 4 | OD268054/2025-2026 Rower - Supply and Installation of Rower having the following specifications: Dimensions: (L X W X H) = 1472 x 915 x 1040 mm. Upper and bottom pipes - Ø 88 mm OD “B” Class GI pipe. Foundation plate –M.S. round plate of Ø 250 mm & 8 mm thick. Handle - Ø 33 mm OD “B” Class G.I pipe. Angle between handle and horizontal surface is 75 - 80 degree. Linkages – Ø 48 mm OD “B” Class G.I. pipe.Seat & back rest – 380 x 275 x 60mm thick high-density polyethylene (HDPE) blow molded with M10 in-sert wall thickness 3 to 4 mm. Foot resting pipe - Ø 60 mm OD “B” Class G.I. pipe. End Closing cap – dome shape made by PP / NYLON / HDPE material. Closing caps – PP / NYLON / HDPE material. Foundation stool: Made from main pipe Ø 88 mm OD M.S pipe and top support of M.S. round plate of Ø250 mm & 8mm thickness is welded at top. Square tube of 30 x 30 x 2 mm must be used to support center pipe. Height of stool is 3 ft. Foundation stool is embedded in C.C. stock below ground level. Pin – Ø 25 mm M.S. bright bar pin. Circlips– A 24 circlips are used for assembly. Bearing bushes - Ø 60 mm OD seamless pipe / Bar. Bearing- use is 6005 permanent lubricated reputed brands. Grips – high quality rubber 46 mm OD. Coating - best quality of powder coating 80 -120 micron. Safety Instructions and Exercise chart - start & finish position stick on product. All joints must be welded as per IS standards and zinc primer paint should be applied at all the welding points prior to finishing. (Foundation shall be M20 CC and design shall be approved by the Engineer-in -charge before installation.) |
| 5 | OD313240/2025-2026 Leg Press (Double) - specifications: Dimensions: (L X W X H) = 1676 x 400 x1500 mm. Main frame - Ø 114 mm OD “B” class GI pipe.Foundation plate – M.S. round plate of Ø 250 mm & 8 mm thick. Foundations cover cap - dome shape of PP / NYLON / HDPE material. Link - is Ø 60 mm OD “B” Class GI pipe. Seat frame - Ø 42 mm OD “B” Class GI pipe. Leg Press back rest should be angled in 120 - 130 degree. Footrest - cast iron 124 x 296 x 5 mm thick and M.S plate of 2 mm thick use to support it. Seat & back rest – 380 x 275 x 60 mm thick high- density polyethylene (HDPE) blow molded with M10 integrated wall thickness 3 to 4 mm. Link connected with frame by 8 mm thick laser cutting MS profile. Top Closing cap – dome shape made by PP / NYLON / HDPE material. Closing cap’s- PP / NYLON / HDPE material. Foundation stool: Made from main pipe Ø 88 mm OD M.S pipe and top support of M.S. round plate of Ø 250 mm & 8 mm thickness is welded at top. Square tube of 30 x 30 x 2 mm must be used to support center pipe. Height of stool is 3 ft. Foundation stool is embedded in C.C. stock below ground level. Bearing- use is 6005 permanent lubricated reputed brand. Pin– Ø 25 mm M.S. bright bar pin. Bearing bushes - Ø 60 mm OD seamless pipe. Circlip– A 24 circlips are used for assembly. Coating - best quality of powder coating 80 -120 micron. Safety Instructions and Exercise chart - start & finish position stick on product. All joints must be welded as per IS standards and zinc primer paint should be applied at all the welding points prior to finishing. (Foundation shall be min M20 CC and design shall be approved by the Engineer-in -charge before installation.) Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 01, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 11, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 4 daysAug 13, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 6 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender