Tender for Tender for Nit 07/2026-27 erection of Nagar Palika Chaksu Convention Center Auditorium Hetu Vc Setup Evam Anya Vikas Karya
Tender Value
Ref. Documents
Estimated cost
Bid Submission
13 Aug 2026
10 days left
EMD
13.08 Lakhs
Bank guarantee accepted
Document Fee
5000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jaipur → Rajasthan
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Nit 07/2026-27 erection of Nagar Palika Chaksu Convention Center Auditorium Hetu Vc Setup Evam Anya Vikas Karya
BOQ
| Sl. No. | Item Description |
| 1 | Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared. |
| 2 | Earth work in excavation by mechanical means (Hydraulic Excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5 m, including taking out the excavated soil and depositing and refilling of pit with watering & ramming and disposal of surplus excavated soil as directed within a lead of 50 meter. All kinds of soils. |
| 3 | Filling available excavated earth (excluding rock) in trenches, plinth side of foundation etc. in layers not exceeding 20 cm. in depth, consolidating each deposited layer by ramming and watering including lead up to 50 meter and with all lift. |
| 4 | Diluting and injection Chloropyrifos Emulsifiable concentrate 20% with 1% concentration for PRE-CONSTRUCTIONAL Anti termite treatment as per IS 6313 part III as amended from time to time and creating a continuous chemical barrier under and around the column pits, wall trenches, basement excavation, top surface of plinth filling, junction of wall and floor along the external perimeter of building expansion joints, over the top surface of consolidated earth of which aproch is to be laid surrounding of pipes and conduits etc. complete as per specification (Plinth floor area only shall be measured for payment and excluding the cost of chemical emulsion) |
| 5 | Supplying chemical emulsion in sealed containers including delivery as specified. Chlorpyriphos/Lindane emulsifiable concentrate of 20% |
| 6 | Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. 1:4:8 (1 cement: 4 coarse sand: 8 graded stone aggregate 40 mm |
| 7 | Random Rubble stone masonry for with hard stone in foundation and plinth in Cement Sand mortar above 30 CM thick wall in:Cement Mortar 1:6 (1-Cement : 6-Sand). |
| 8 | Random Rubble dry stone kharanja under floor |
| 9 | Sand filling under floor |
| 10 | Providing and laying in position cement concrete, including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering. All work up to plinth level |
| 11 | Centering and shuttering with plywood or steel sheets including strutting, propping, bracing both ways and removal of formwork for foundation, footings, strap beam, raft, bases of columns etc. |
| 12 | Centering & shuttering with plywood or steel sheets including strutting, propping, bracing both ways with steel props and removal of formwork for up to floor five level for: |
| 13 | Providing and fabricating reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor five level.(Original producers who manufacture billet directly from iron ores and roll the billets to produce steel conforming to IS:1786) |
| 14 | Providing and laying in position specified grade of cement concrete for all RCC structural elements up to plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement : 3 coarse sand) and making good the joints and cost of plasticizers (if required), excluding the cost of centering, shuttering and reinforcement.M20 Grade – Nominal Mix / Design Mixdirected within a lead of 50 meter. All kinds of soils. |
| 15 | Add extra for providing richer mixes respectively at all floor levelsProviding M-25 grade concrete by using cement as per codal provision instead of M-20 grade design mix.QUANTITY SAME AS RCC QUANTITY = 285.66 |
| 16 | Fine grinded Gangsaw cut 30–35 mm thick stone flooring over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand), jointed with grey cement slurry mixed with pigment to match the shade of stone, complete as per design drawing and instruction of Engineer-in-Charge. |
| 17 | Plaster on new surface on walls in cement sand mortar 1:6 including racking of joints etc., complete fine finish: |
| 18 | Centering & shuttering with plywood or steel sheets including strutting, propping, bracing both ways with steel props and removal of formwork for upto floor five level for: |
| 19 | Columns, Pillars, Posts and Struts etc. |
| 20 | Providing and fabricating reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) complete up to floor five level. 13.3.3 Thermo-mechanically Treated (TMT) Bars (Conforming to relevant IS Code) |
| 21 | Providing and laying in position specified grade of cement concrete for RCC structural elements up to floor five level including curing, compaction, finishing, excluding centering, shuttering and reinforcement.Grade: M20 (Nominal Mix / Design Mix) |
| 22 | Providing and laying in position specified grade of cement concrete for RCC structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1) cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement for Arches, arch ribs, domes, vaults, shells, folded plate, chimneys, shafts, roofs having slope more than 15º, vertical and horizontal fins individually or forming box louvers, facias and eavesboards M20 grade Nominal Mix / Design Mix |
| 23 | Add extra for providing richer mixes respectively at all floor levels provinding M-25 grade concrete by using min 410 Kh og cement per com instead m-20 grade desing moix |
| 24 | Brick work with mechanised autoclaved flyash lime bricks conforming to IS: 12894 :2002 of class designation 100 insuperstructure above plinth level upto floor V level in. |
| 25 | Half Brick work with mechanised autoclaved flyash lime bricksconforming to IS: 12894 :2002 of class designation 100 in superstructure above plinth level upto floor V level in |
| 26 | P & F-1st quality Heavy Duty Vitrified glazed MAT tiles on floor, skirting and steps etc.in different sizes (thickness minimum 10mm) with water absortion less than or equal 0.08% and conforming to IS 15622 of approved make in all colour and shade, laid with 20 mm thick CM 1: 4 including grounting the joints with white cement and matching pigment etc complete. |
| 27 | Providing and fixing Granite stone slab mirror polished and machineedge cut in walls, pillars, steps, Shelves, Sills Counters, Floors etc. laid on12mm (Av.) thick base of cement mortar 1:3 (1 cement: 3 coarse sand)jointing with white cement mortar 1:2 (1white cement: 2 marble dust)with pigment to match the shade of the marble slab including grinding,rubbing and polishing complete. |
| 28 | Extra for providing edge moulding to 15-18mm thick marble/ Granite stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Full edge moulding |
| 29 | Extra for providing edge moulding to 15-18mm thick marble/ Granite stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Half edge moulding |
| 30 | Extra for providing opening of required size & shape for wash basins/kitchen sink in kitchen platform, vanity counters and similar location in marble/Granite/stone work including necessary holes for pillar taps etc. including rubbing and polishing of cut edges etc. complete |
| 31 | Providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles confirming to IS: 13753 & IS :15622 of size 200mm x 300mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster on walls and pillar). |
| 32 | Extra for using size above 200x300mm in glazed tiles and for using 400mm x 400mm MAT finished tiles in place of 300mm x 300mm size. 10% |
| 33 | Providing and fixing 1st quality MAT finished ceremic tile size 300x300mm confirming to IS: 13755 and IS: 15622 colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (including the cost of cement mortar bed 1:4). |
| 34 | Extra for using size above 200x300mm in glazed tiles and for using 400mm x 400mm MAT finished tiles in place of 300mm x 300mm size. |
| 35 | Providing and fixing aluminum work for doors, windows, ventilators and partition with extruded built up standard tubular /appropriate Z sections and other sections of approved make conforming to IS:733 and IS: 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gap. at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium section shall be smooth rust free, straight, mitered and jointed mechanically wherever required including cleat angle Aluminium snap beading for glazing /paneling, C.P. brass/ stainless steel screws Al. Tower bolt & Al. handle & Al. Aldrop etc., all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and paneling to be paid for separately). For fixed portion Powder coating aluminum (minimum thickness of powder coating 50 micron) |
| 36 | For shutters builtup standard tubular sections of openable doors windows & ventilators including providing & fixing hinges / rollers etc. and making provision for fixing of fittings wherever required (lockes shall be paid for separately).Powder coating aluminum (minimum thickness of powder coating 50 micron) |
| 37 | Extra for shutters of sliding aluminum windows |
| 38 | S&f fixed wire gauge of stainless steel of 14 mesh x 24 gauge to the aluminium window by Aluminium beading 20x3mm with suitable screws not exceeding 150mın distance at all heights with all lead and lift with scafolding. |
| 39 | Providing and fixing 12 mm thick prelaminated three layer medium density (exterior grade) particle board Grade 1, Type II conforming to 15: 12823 bonded formaldehyde synthetic resin, of approved brand and manufacture in paneling fixed in aluminium doors, windows shutters and partition frames with C.P. brass/stainless steel screws etc. complete as per architectural drawings and direction of engineer-in-charge. Prelaminated particle board with decorative lamination on both sides. |
| 40 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with PVS/neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item.) With float glass panes of 5.0 mm thickness (weight not less than 13.50 kg/sqm) |
| 41 | Extra for providing toughened glass panes instead of ordinary float glass panes in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured). |
| 42 | Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS: 6315 marked, for doors including cost of cutting floors as required, embedding in floors and cover plates with brass pivot and single piece M.S. With stainless steel cover plate |
| 43 | Providing and fixing 100mm brass locks (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete. |
| 44 | Filling the gap upto 5 mm depth and 5 mm width in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. |
| 45 | Providing and fixing external grade board solid core single leaf flush door shutters ISI 2202-67 marked using Phenol formal dehyderesin in glue both sides with approved steel fittings complete as per annexure 'A' : |
| 46 | Providing and fixing fullypanelled/partlypanelled/ double leaf shutter frames for doors as per approved design and drawingswithapprovedordinaryC.P./oxidisedsteel fittings asperAnnexure 'A'andwidth ofstyles&toprailsof 100mm and lock railswidth of 150mmandbottomrails of 200mniwidthincludingteakwoodbeadingofsize19mmx12mmon both faces complete: |
| 47 | Providing & Fixing mica of approved make for inner/outer side of shutters with fevicol & nails complete as per approved by engineer in charge. 0.8mm thick mic |
| 48 | Extra for providing other type of fittings as mention in annexure A (as approved by El): Brass fittings (Ivory coast wood grade I AREA) |
| 49 | Extra for providing ather type of fittings as mention in annexure A (as approved by El):Stainless steel fittings |
| 50 | Extra for providing external lipping with 2nd class teak wood battens 6 mm minimum depth on all edges of shutters (over all area of door shutter to be measured) Over item no. 8.13.quantity same as of 8.13.3.1 |
| 51 | Extra for providing vision panel not exceeding 0.1 Sqm in all type of flush doors (cost of glass excluded) (overall area of door shutter to be measured):D2 |
| 52 | Extra for cutting rebate in flush door shutters for making double leaf shutter(Total area of the shutter to be measured) |
| 53 | Providing and fixing bright finished Mortice lock of approved make Godrej or equivalent with pair of CP handles for doors with necessary screws etc complete (Best make of approved quality) as per direction of Engineer-in-charge. |
| 54 | Providing and fixing IS: 3564 marked Aluminium die cast body tubular type universal hydraulic door closer with necessary accessories and screws etc. complete. |
| 55 | Providing and fixing M.S. sheet 1mm thick single leaf door shutter in angle iron frame 35x35x5mm suitabilly diagonally braced with 25x3mm flat iron above. and below lock rail of size 50x5mm beading extra including all fittings, as per direction of Engg. incharge but excluding cost of chowkhats: including two coats of anit-corrosive red oxide primer pain |
| 56 | Providing and fixing factory made P.V.C. door frame of size 50x47mm with a wall thickness of 5mm, made out of extruded 5mm rigid PVC foam sheet mitred at corners and joined with 2 Nos. of 150mm long brackets of 15x15mm M.S. square tube, the vertical door profiles to be reinforced with 19x19mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100mm size complete as per manufacturers specification and direction of Engineer-in-Charge. |
| 57 | Providing and fixing to existing door frames. |
| 58 | Plaster on new surface on walls in cement sand mortar 1:6 including racking of joints etc. complete fine finish: |
| 59 | Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish :20mm thick (outer Plaster) |
| 60 | Making grooves as per design in plaster 10mm to 20mm wide.230mm thick wall |
| 61 | Making of drip course (Tapka) in cement sand mortar 1:6 width upto 40 mm and 10 mm thick as per approved design |
| 62 | Providing and applying white cement based putty over plastered surface to prepare the surface even and smooth complete (New plastered surface three or more coats) |
| 63 | Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade including all scaffolding:Two or more coats on new work including prepartion of base with primer, putty, lippy etc complete in all respect.Internal plaster |
| 64 | Trowel Finish av. thickness 1500 to 2000 microns.qty of external plaster.(30% of exter plaster quantity) |
| 65 | Finishing walls with textured exterior paint of required shade as per approved colour complete as per manufacturers specifications including primer coat and protecting coat including scaffolding and safety provisionTrowel Finish av. thickness 1500 to 2000 microns.\qty of external plaster. (30% of exter plaster quantity)RollerFinish av. thickness 400 to 500 microns. (70% of external plaster) |
| 66 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade: |
| 67 | Providing and fixing stainless steel railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). Grade 304 |
| 68 | Providing and fixing steel gate, grating, and grills made of angles, tees, square bars, flats, or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide |
| 69 | Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying:a) first layer of slurry of cement @ 0.488 kg/sqm mixed with water proffing cement compound @0.253 kg//sqm.This layer will be allowed to air cure for 4 hours.b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water |
| 70 | Cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 Graded stone aggregate 20 mm nominal size |
| 71 | Finishing with neat cement (punning) |
| 72 | Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 stone aggregate 10mm and down gauge) including finishing with cement mortar 1:3 (1 cement: 3 fine sand) as per standard design: |
| 73 | Providing and laying damp-proof course with cement concrete grade M-150 (1 2:4) mortar prepared with 1% solution of water-proof compound complete as per specification.50mm thick. |
| 74 | Rough Chisel dressed Sand stone 35 mm thick flooring of approved shade set over 20mm thick base of cement mortar 1:6 (1 cement: 6 coarse sand) and pointing with cement sand mortar 1:3 with pigment to match the shade of stone with joint thickness up to 15 mm complete in all respectsRed sand stone (Karauli stone) same as coping |
| 75 | Making khurras 450 x 450mm with average minimum thickness 50mm cement concrete 1: 2:4 over P.V.C. Sheet 1 Mtr. x 1 Mtr. x 40micron finished with 12mm cement plaster 1: 3 and one coat of neat cement, rounding edges and making and finishing the out let complete. |
| 76 | Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing and cleaning etc. complete on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand) |
| 77 | Steel work in built up tubular trusses including cutting, hoisting (height upto 10 m)fixing in position and applying a priming coat of approved steel primer, welded and bolted including special shaped washers etc. complete.Hot finished welded type tubes (truss area)40kg/m2 Lumpsump qty |
| 78 | Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead and including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/vertical or curved surfaces) excluding the cost of purlins, rafters and trusses and including cutting to size and shape whenever required.0.80 mm thick with zinc coating not less than 275 gm/m2 |
| 79 | Providing ridges or hips of width 60 cm over all width plain G.S. sheet fixed with polymer coated Jor L hooks, bolts and nuts 8 mm dia. G.I. limpet and bitumen washers complete.0.80mm thick with zinc coating not less than 275ADD AMOUNT FOR MODULAR KITCHENADD FOR ORNAMENTAL WORK IN MASONARY, JALI AND PAINTING ETC |
| 80 | ADD AMOUNT FOR MODULAR KITCHEN |
| 81 | ADD FOR ORNAMENTAL WORK IN MASONARY, JALI AND PAINTING ETC |
| 82 | Earth work in excavation by mechanical means (Hydraulic Excavator manual m trenches or drains (not exceeding 1.5 m in width or 10 sqın on plan) including dre ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and d refilling of jhiri with watering & ramming and disposal of surplus excavated soil a lead of 50 meter. All kinds of soils |
| 83 | M10 grade Nominal Mix 1:3:6(Icement 3coarsesand:6gradedstone aggregate 201 |
| 84 | Centering and Shuttering with plywood or steel sheets including strutting, proppin and removal of formwork for foundation, footings, strap beam, raft, bases of col |
| 85 | Centering & shuttering with ply wood or steel sheets including strutting, propping with steel props and removal of formwork for upto floor five level for: |
| 86 | Suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands. Janchor blocks, sills, chhajjas, lintel, beam, plinth beam etc. |
| 87 | Providing and fabricating reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor Five level. Thermo-mechanically Treated bars (Conforming of relevent IS code) |
| 88 | Providing and laying in position specified grade of cement concrete for all RCC structural clements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 13 (1) cement: 3 coarse sand) and making good the joints and cost of plastizerst if required) excluding the cost of centering, shuttering and reinforcement. |
| 89 | Providing M-25 grade concrete by using cement as per codal provision instead of M-20 grade design mix. |
| 90 | Suplying and Fixing Ductile tron Man Hole Covers storm water grating and gratingwith frame of various sizes weight and types and load bearing capacity as per EN-124 superior quality or equivalent comlete as per Direction of Engineer In chargecovers |
| 91 | ladder pipe and other item etc |
| 92 | Construction of tube well from ground level and up to 100 mtr depth and above to accommodate housing assembly pipe in all type of unconsolidated formation such as pebbles, boulders, collapsible formation etc. by Odex drilling method as per IS: IS:2800 Part 1: 1991 and 15:2800 Part II: 1979 (both amended up to date) and technical specifications. The work will include lowering of housing and strainer pipe assembly and casing shoe including cost of casing shoe, but excluding cost of the casing pipe. The work would be completed after obtaining sand free water.Nominal bore 200 mm dia |
| 93 | Add 15% extra on above item (Item No 2.6.1 to 2.6.3) for drilling depth beyond 100 mtr, rate shall be applicable for only extra depth beyond 100 mtr |
| 94 | Labour charges for making slots on blank pipes made of ERW MS black pipe ISI marked of following sizes, the slotting should be as per IS:8110-1985.200 mm dia nominal bore of 5.4mm thickness |
| 95 | Supply & Fixing tube well cover of MS sheet 8inm thick at top & Snum thick 100mm wide shroud around the edge so as to form a cap on the top end of casing pipe with Gl Nipple 45cm long & two Gi flanges at both ends in 20mini sizes passing through a hole in the centre of MS sheet. A 25 mm socket with end plug shall also be welded over top plate. A Gi nipple having outside thread of size 1/2\\" (for installation pressure gaugel shall be provided & welded with 80mm Gf maple near top plate nipple sha'l be provided with end plug200 mm dia |
| 96 | Supply & Installation of 3 phase ISI marked submersible motor pump set of three star or better rating of BEE and as per 15: 8034-2018 (pump) and 159283-2013 (motor) or as amended up to date of approved make of following duty condition with required accessories Including making connection suitable for tube well/DCB. The job includes lowering of motor pump, installation of complete fitting & accessories, jointing of electrical cables up to switch board, testing of submersible pump set and interconnection up to water mains, coniplete in all respect.9.3 KW (12.5 HP) & head above 120 mtr |
| 97 | Supply & Firing of IS) marked three core PVC flat submersible cable as per 15 694 1990 or amended up to date and conductor us per class 5 of 15 8130:1980 including making connection etc.3 core 4.0 Sq.mm |
| 98 | Supply & Fixing XLPE insulated/P.V.C. sheathed cable of 1.1 KV grade with aluminium conductor Armoured of IS:7098-4/1554-1 approved make in ground as per 15:1255 including excavation of 30cmx75cm size trench, 25 cm thick under layer of sand, second Class bricks covering, refilling earth, compaction of earth, making necessary connection, testing etc. as required of size 16.050mm, 4 core |
| 99 | Providing & Lowering in tube well ISI marked Gl Pipe medium duty (\\"B\\" class), Steel tube as per 15:1239 or amended up to date and zinc coating as per 15 4736, threaded and double flanged (welded) on both ends and two number 25x3mm MS flat welded on both ends between pipe & flange, rubber washer & nut bolts etc. complete in all respect 50 mm dia |
| 100 | Providing & laying St marked Gi Pipe Light duty (\\"A\\" class) as per 15: 1239 for casing pipe for submersible cable external work 40 mm dia complete in all respect. |
| 101 | Providing & Fixing of double flanged, Ci body, 15 marked NRV of approved make of following sizes 80 mm dia |
| 102 | Providing & Lowering in tube well Si marked Gl Pipe medium duty (\\"B\\" class), Steel tube as per 15:1239 or amended up to date and zinc coating as per 154736, threaded and double flanged (welded) on both ends and two number 25x3mm MS flat welded on both ends between pipe & flange, rubber washer &nut boits etc. complete in all respect. 80 mm dia |
| 103 | Providing, installing, testing and commissioning of double flanged bulk flow meter with removable mechanism, of class B conforming to 150 4064/1 or amended up to date of approved make including cost of all material and labour as per specifications with Gl Box (sheet 16 SWG) suitable with lockingarrangement of following dia. 50 mm dia |
| 104 | Supply and Fising of electric control feeder panel comprising of suitable rating MCCB, fully automatic star-delta starter, over load relay, ampere meter with CTs, volt meter, phase preventer, suitable starting capacitors, phase indicators, lighting arrangement etc. complete suitable for three phase pump set. The panel should have space for energy meter (supplied by DISCOM) All these equipments shall be housed by panel box made out from 18 gauge M.5. Sheet with powder coating. Panel should be of minimum size 900 x 600 x 450 mm with Stand (made of angle iron of size 35x35x5mm) duly bolted/screwed with enclosure box having 4 legs, each leg's length 18\\" and double door including in built locking system. The legs should be embedded in M-15 cement concrete plat form. The size of CC platform should be equal or bigger than the base size of panel having height of at least 200 mm from ground level. The panel should have opening of suitable size in front of space for energy meter with glass for meter reading. The operation of panel should be suitable for on 440 Volt AC Supply.Above 10 HP and up to 15 HP |
| 105 | Plate Earthing as per 15.3043 with G.1. Earth plate of size 600mm x 600mm x 6.0mm by embodying 3 to 4 mtr. below the ground level with 20 mns dia. G.1. 'B' class watering Pipe including all accessories bike nut, bolts, reducer, nipple, wire meshed funnel, and C.C. finished chamber covered with hinged type with locking arrangenvent C.I. Cover, C.I. Frame of size 300mm x 300mm complete with alternate layers of salt and coke/charcoal, testing of earth resistance as required. |
| 106 | Providing & Fixing pump safety cage as per specifications or as directed by Engineer in charge. |
| 107 | Supplying & Installing 100 mm diameter sealed diaphragm bourdon type pressure gauge of range 0 to 10 kg. including all jointing material as per specification with safety cover. |
| 108 | Supply of ERW M.S. black casing pipe ISI marked (IS: 4270/2001) or amended up to date of following sizes 200 mm dia NB (Thickness of pipe 5.4mm & mass of tube 28.46 Kg/m) |
| 109 | Add for electric connections Is |
| 110 | Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. All kinds of soils |
| 111 | Providing and laying in position cement concrete including curing, compaction ete complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. 14:8 (1 cement 4 coarse sand 8 graded stone aggregate 40 mm nominal size). |
| 112 | Random Rubble stone masomy for with hard stone in foundation and plinth in Cement Sand mortar above 30 CM thick wall in Cement Mortar 16 (1-Cement: 6-Sandi |
| 113 | Centering and Shuttering with plywood or steel sheets including strutting, propping bracing both ways and removal of formwork for foundation, footings, strap beam, raft, bases of columns ete |
| 114 | Providing and laying in position specified grade of cement concrete for all RCC structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizerst if required) excluding the cost of centering, shuttering and reinforcement. M20 grade Nominal Mix/Design Mix |
| 115 | Providing and laying in position cement concrete including curing, compaction ete, complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. M15 grade Nominal Mix 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 40mun nominal size) extra piller |
| 116 | Brick work with mechanised autoclaved flyash lime bricks conforming to IS: 12894 :2002 of class designation 100 in superstructure above plinth level upto floor. V level in Cement mortar 16 (1 cement 6 coarse sand) extra colomn |
| 117 | Providing and laying in position cement concrete including curing, compaction ete, complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. M15 grade Nominal Mix 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 40mun nominal size) |
| 118 | Providing and fixing steel gate, grating and grills made of angles, tees, square bars, flats.or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide. Extra if square, rectangular hollow, tublar section are used for grill made by flatts only |
| 119 | Plaster on new surface on walls in cement sand mortar 16 including raking of joints etc, complete fime fimsh. 20 mm thick. |
| 120 | New work (Two or more coat applied @ 1.67 Itr/10 sqm over and including base coat of water proofing cement paint applied 2.20 kg/ 10 sqm). as per plaster item no 11top, piller top |
| 121 | Add extra for decorative work on front side of wall |
| 122 | Construction of granular sub-base by providing well graded material, spreading in uniform layers with Tractor Mount Grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density.complete as per MoRTH Specification Clause 401. Grading-2 |
| 123 | Construction of dry lean cement concrete Sub- base over a prepared sub-grade with coarse and tine aggregate conforming to IS: 383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per table 600-1, cement content not to be less than 150 kg/ cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, laid with a paver with electronic sensor, compacting with 8-10 tonnes vibratory roller, finishing and curing. |
| 124 | Providing and Laying of Interlocking M-30 grade Concrete Block Pavements having thickness 80 nun as per drawings and as per IS 15658:2006 and all materials shall conform to MORTH Specification Clause 602 with M-30 Grade 0.30 Mtr x 0.30 Mtr x 0.15 Mtr Edge BlocksCategory 'A': Dentated units to key into each other on all four faces Zigzag shape as per |
| 125 | Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing and cleaning etc. complete on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand Light shade using shade cement. |
| 126 | Earth work in excavation by mechanical means (Hydraulic Excavator) manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramining of bottoms, lift upto 1.5 m. including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. All kinds of soils |
| 127 | Providing and laying in position cement concrete including curing, compaction ete. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. 1.4.8 (1 cement 4 coarse sand 8 graded stone aggregate 40 mm nominal size). |
| 128 | Brick work with mechanised autoclaved flyash lume bricks conforming to IS 12894 2002 of class designation 100 in superstructure above plinth level upto floor V level in.Cement mortar 1:6 (1 cement: 6 coarse sand) |
| 129 | Plaster on new surface on walls in cement sand mortar 1:4 including racking of joint etc. complete fine furish:20mm thick. |
| 130 | Random rubble dry stone Kharanja under floor |
| 131 | Cement concrete flooring 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, making of lines or groove etc complete but excluding the cost of nosing of steps ete complete 75mm thick with 20mm thick nominal size aggregate. |
| 132 | Stone Aggregate filling (Single size): 63 mm nominal size |
| 133 | Stone Aggregate filling (Single size): 12.5 mm nominal size |
| 134 | Bajri tilling |
| 135 | Providing and fixing of Reinforced Ferro cement Drain cover designed for class \\"B\\" loading duly marked on cover with adequate steel reinforcement having thickness 50 mm to 75 mm anti-corrosive bitumen painted M.S. plate Rim and on M.S. lifting hooks admusture like plasticizer bond improving compound shrinkage resistance compound abrasion resistant complete as per approved design ete for drain Opening Size 1201 to 1500 mm Standard Drain Cover Size 1800mm x |
| 136 | Construction of tube well from ground level and up to 100 mtr depth and above to accommodate housing assembly pipe in all type of unconsolidated formation such as pebbles, boulders, collapsible formation ete, by Odex drilling method as per IS: IS:2800 Part 1: 1991 and IS:2800 Part II: 1979 (both amended up to date) and technical specifications. The work will include lowering of housing and strainer pipe assembly and casing shoe including cost of casing shoe, but excluding cost of the casing pipe. The work would be completed after obtaining sand free water.Nominal bore 200 mm dia. |
| 137 | Supply of ERW M.S. black casing pipe ISI marked (is: 4270/2001) or amended up to date of following sizes200 mm dia NB (Thickness of pipe 5.4mm & mass of tube 28.46 Kg/m) |
| 138 | Earth work in excavation by mechanical means (Hydraulic Excavator)/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. All kinds of soils |
| 139 | 1:4.8 (1 cement: 4 coarse sand: 8 graded stone aggregate 40 mun nominal size) |
| 140 | Random Rubble stone masonry for with hard stone in foundation and plinth in Cement Sand mortar above 30 CM thick wall in:Cement Mortar 1:6 (1-Cement: 6-Sand). |
| 141 | Brick work with mechanised autoclaved flyash lime bricks conforming to IS: 12894:2002 of class designation 100 in superstructure above plinth level upto floor V level in. Cement mortar 1:6 (1 cement: 6 coarse sand) |
| 142 | Centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel props and removal of formwork for upto floor five level forSuspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates, anchor blocks, sills, chhajjas, lintel, beam, plinth beam etc. |
| 143 | Providing and fabricating reinforcement for R.C.C. work including straightening, cutting, bending. placing in position and binding (including cost of binding wire) all complete up to floor Five level. Thermo-mechanically Treated bars (Conforming of relevent IS code) |
| 144 | Providing and laying in position specified grade of cement concrete for all RCC structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 13 (1 cement 3 coarse sand and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement. M20 grade Nominal Mix/Design Mix |
| 145 | Providing and laying in position specified grade of cement concrete for RCC structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers (if required ) excluding the cost of centering, shuttering and reinforcement for Walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. M20 grade Nominal Mix/Design Mix |
| 146 | filling available excavated earth in trenches plingth side of foundation ftc in layers not exceeding 20cm in depth consolidating each depositednlayers by layers..etc |
| 147 | Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish : 20mm thick ((External Plaster) |
| 148 | 12 mm thick in inner Sw inner deduction gate windows |
| 149 | Providing and applying white cement based putty over plastered surface to prepare the surface evenPuttyCelling PuttyInternal Putty |
| 150 | Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade Same as plaster (internal and external) and ceiling area |
| 151 | Random rubble dry stone kharanja under floor |
| 152 | 1:4:8(1cement :4coarsesand:8gradedstoneaggregate40 mm nominal size). pcc under floor |
| 153 | Kota stone slab flooring 25 mm thick over 20 mm (average) thick base laid over and jointed with grey |
| 154 | Grading roof for water proofing treatment with water proffing compoundCement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) |
| 155 | Providing and fixing steel glazed doors windows and ventilator shutters of standard rolled steel Partly fixed and partly openable [fixed area not to exceed 33% |
| 156 | Providing and fixing M.S. sheet 1mm thick single leaf door shutter in angle iron frame 35x35x5m/m |
| 157 | Add extra for double leaf shutters. (20%) |
| 158 | supply and fixing wire guage of 14 mesh 24 guage to the metal frame of rolled section by metal |
| 159 | Providing and fixing square bars or other flate welded to windows, ventilator etc windows |
| 160 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shadeTwo or more coats on new work gate windows |
| 161 | Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 stone aggregate gola |
| 162 | P&F rigid PVC Pipe (IS:4985 mark) class II/ (4 Kg./Cm2.) approved quality/make including joining the |
| 163 | Electricity items and fitting L.S. |
| 164 | Wiring of light point fan point exhaust fan pomt call bell point with 13 sq min nominal suve FR PVC insulated unsheathed flexible class 2copper conductor 11KV grade and 15 sq om sommal size FR PVC invulned unsheathed flexible class 2 copper cartii conductor 11 LV grade 15. 6941 in recessed ISI marked MMS IS 9537P-III) PVC conduit & its St market (15 3419-1988) accessories. Alumna rand nles, 12 mm thick. Hat Dipped Galvanized Modular Doo with earth termenal, to A Modular switch Modular face plate with grid phate 3 pin ceiling rose Holder 13 way connector, screws, making connectiom, jesting ete, as required Shon point tuy to 3 mtr) |
| 165 | Medium point (up to 6 mtr) |
| 166 | Long pout top te 10 mtr) |
| 167 | Weing of twin control light point with 15 sq nim nominal size FR PVC insulated usheathed flexible class 2 copper conductor 11 KV grade and 15 sq. mri nominal size FR PVC insulated unsheathed flexible class 2 copper earth conductor 1.1 LV grade (15.694) in recessed ISI marked MMS: IS:9537P-III PVC conduit & it's ISI marked (15 3419-1988) accessories, Alumunium round tiles 2 Nes Hot Dipped Galvanized MS Modular bov of 12 min thick with earth terminal 2 Nos 6 A two way Modular switch 3 pin ceiling rose/holder/way connector Modular face plate with grind plate screws, making connections, testing ete as required Short point tuy to 3 mtr) |
| 168 | Medium point (up to 6 mtr) |
| 169 | Long pout top te 10 mtr) |
| 170 | Wiring of 3/5 pin 6 amp. Light plug point with 15 sq mus nominal size FR PVC insulated unshcathed flexible class 2 copper conductor 11 W grade and 15 sq mm nominal stze FR PVC insulated unsheathed flexible class 2 copper earth conductor 11 KV grade15 694) in recessed IST marked MMS (IS 9537 P-III) PVC conduit & its IS1 marked (IS 3419-1985)accessories, Hot Dipped Galvanized Modular box of 12 min thick with earth terminal & A modular switch, 315 pin 6 A modular socket, Moduku face plate with gral plate, screws, making connections, testing ete, as required on board |
| 171 | SHort point (up to 3 mtr) |
| 172 | Medium point (up to 6 mtr) |
| 173 | Long point top t0 10 mtr) |
| 174 | S&F following sizes (dia) of ISI marked MMS (IS 9537 P-III) PVC conduit along with ISI marked (IS 3419-1988) accessories as required in recess including making thiri in the wall clamps at suitable spacing, covering conduit and making good the same as required. 20 mm |
| 175 | 25 mm |
| 176 | 32 mm |
| 177 | 40 mm |
| 178 | Suppling and laying FR PVC insulated & unsheathed flexible copper conductor of following nominal sizes with ISI marked 11S 694) and as per IS 8130 2013 of 11 kV grade Wire should he made from copper stranding in acc to IS $130/IEC 60228 for lower watt loss, oxygen free for less chances of oxidization, insulation PVC type A/C/D flame retardant as per 15 10810-53, better amperage rating as per IS 3961 part 5, in existing sürface or recessed PVC/ MS condut/casing capping making connections with Copper Lugs of suitable sue, Ferrules testing etc as required.1x.15 sq mm I for Invertor 1 |
| 179 | 3x 1.5 sqmm |
| 180 | 2 x 2.5 sq. mm. + 1x1.5sqmm |
| 181 | 1 x 4.0 sq.mm (For Earthing LDB/PDB) |
| 182 | 2 x 4.0 sq. mm. + 1 x 2.5 sq.mm. |
| 183 | 4 x 6.0 sq.mm ( For LDB) |
| 184 | 2 x 6.0 sq. mm. + 1 x 2.5 sq. mm. |
| 185 | 4 x 10.0 sq.mm (For PDB) |
| 186 | Supplying and Laying PE Insulated & PVC Sheathed unarmoured telephone cable with 0.5 mm dia. Solid Annealed electrolytic grade hare Copper Conductor as per 15 813084 & confirming to TEC specification GR/WII/06-03 March 2002 in existing surface or recessed conduit/casing capping, including ferruling on cach pair for Identification etc as reqinred 2 pair |
| 187 | 5 Pair |
| 188 | 20 Pair |
| 189 | 50 Pair |
| 190 | Supplying and Laying couvial cable 75 ohin umpedance with foam Pli insulated solid bare copper wner conductor, and it outer conductor of bonded clum tape and second cuter conductor of alun, alloy braid in existing surface or recessed conduit/casing capping including maling connections as required RG-6 |
| 191 | Supply and laying speaker cable of following size 2 core twin twisted multi stranded electrolytic grade copper conductor, overall PVC imsulated and armoured cable (Blue colour) on surface/ above false ceiling including cost of Gl spacers, saddles etc, as required 15 Sq mm |
| 192 | Supplying and fixing of power plug point with Modular accessories on hot dipped galvanized modular box of 1.2 mm thick with canhing terminal connector on surface or in recessed with suitable size of modular face place with grid plate and cover plate including cost of IS1 marked modular 16 amp. Switch (IS 3854) and 6/16 amp socket outlet (18:1293) making connection testing, etc. as required |
| 193 | P&F 12 mat thick MS Recessed fan box and top lid screwed on Box, hexagonal round of size 130 mm dia, depth 75mm 12 mm dia red fan hook with 150 run length extended on each side as required |
| 194 | P & F paper phenolie resin bonded laminates confirming to IS 2036-1995 for boxes/ frames including making holes for switches etc, with brass screws, washers zine plated not and bolts as required. 13.0 mm thick |
| 195 | Supply, Drawing and Testing of 4 pair. 23 AWG Solid Bare Copper wire insulated with PVC, U/UTP (Unscreened/Unshielded Twisted Pair), Category 6, Class E. 100 Ohm Impedance, Indoor Cable as per Latest ammendments of ANSI/TIA/EIA-568. The copper conducters should be balanced twisted in pairs, seperated by a cross-member fluted pair divider & protected by LSZH Jacket Certified performance in a 4-connector configuration upto 100 Mtrs channel requirements & transmission frequencies ranging from 250 to 500 Mhz, in existing MS/PVC Condoits/easing capping including making connections to Information outlets and Patch Panels with jack & ferruling at both ends for identification with necessary tools for punching, stripping, crimping and testing etc as required complete in all respect |
| 196 | Supply and Installation of unshielded/360 degree shielded PCB based Information outlets made of high impact plastic body with ABS, Flammability rating UL 94 V-0 with provision for protection against Just in jack of Faceplate, suitable for Cat 6/6A application complying to latest amendinents, According to Cat. 6/6A channel, It should support channel as well as components requirements of Cat 6/6A standards a frequencies 250/500 MHz. Cat 6/6A unshielded/slwelded Jock should be suitable to terminate 4 pair. 23/24 AWG solid stranded wire diameters, using 100 Ohm unshielded/shielded balance twisted pair cable, the jack should have toolless/impact termination on reliable copper tin plated Insulation displacement contact, with easy lock mechanisın. It supports IEC 60603-7-4 and complied with ANSI/TIA 568 C2 & ISO/IEC 11801 or latest standard jack should be RJ11 RJ12 & RJ45 compatible. Should suppon Ethernet 1.2 Gb/s ATM Digital video and broadband/baseband analog video, Voice over internet protocol (VOIP) Specifications in existing modular/MS Boxes along with necessary connections as required. All as per pre approved by Engineer in charge Cat 6. Un-sheilded Information Outlet |
| 197 | Supply & fixing of square Faceplate for Flush / Surface Mount Information Outlets Single/Dual or Quad Aperture with dust cover, material should be High-impact, flame retardant, thermoplastic, UL listed material, Suitable for RJ45 unshielded/shielded connection modules Should match with 1. O OEM Dimensions should be 86mm X 86mm as required complete in all respect. All as per pre approved by Engineer im charge single aperture |
| 198 | Supply, Testaliation, Testing and Commissioning of Rack mounted 19\\" IU, 24 Port loaded, CRS chases, powder coated, sheet steel. High-empact, flame retardane, thermoplastic, UL. Listed, Modular Patch Panels with Reas Cable management system and mounting hardware to mount the patch panel Should have port identification mambers printed engraved on front of the panel Exc required. All as per pre approved by Eingmeer in charge Modular Patch Panel Looded with Cat-610 |
| 199 | Supply Installation and Testing of 4 paar, 100 Ohm impedance, Cat 6/6A /Class EEa patch cords should be constructed of minimum 23/24 AWG, stranded bare Copper cable with LSZII Jacket, with an enhanced performance by factory moulded R145 connectors with strain refier boots as per ANSETIA EIA 568-C.2 suitable for Cat 6/6A application complying to latest ammendments Category 6-6A Standards, According to 11A568C2, ISO/IEC 11801, EN 50173, IEC 60603-7-51, EN 60603-7, IEEE 802 Jan minimum requirement for IG BASE-T to 10G BASE-T performance. Patch cords shall be straught thru cable compatible with both 1568-A and 15618-8 wiring schemes, should support IEEE 802 Jaf/IEEE 802.3at for POE applications, Minimum 750 to 1000 mating cycles in plug contacts for Mong durability Should support Ethernet 10GBASE-T, 12 Ghis ATM. Token ring 4/16 Digital videu and broadband baseband analog video, Voice over internet protocal (VOIP) Cat 6, U/UTP (Unscreened/Un-sheilded Twisted Pairy Patch Cord |
| 200 | Supply & Installation of IP-20 & IK-08 Wall mounted Double Section Communication enclosure (Itack) made from powder coated (60 to 80 Micron) CRCA sheet, front sturdy sheet steel frame folded from one piece and welded with minimum 5mm toughened glass Joor, Vertical Mounting Rail 1.0 MM with 'U'Marking, with All round protective channel on the door aperture, lock integrated on front door, top and bottom cover with cable entry provision with gland plates, integrated side walls, 2 pair of 19\\" angles with wall mounting provision on wall Accessories like 1 Ne of 19\\" 111 Horizontal Cable manager, I No of 90 cfm 230V AC Fan with 1 mts long cable, mounting hardware, I No of 19\\" IU, mountable socket strips with 5 nos of SA universal sockets with 2 mts long power chord for supplying power to switches, fans etc along with earth continuity kit, indicator, moulded power supply cable fixing on wall with Suitable Anchor fastner ete as required. 9 U Rack with Width 600 mm & Depth 400 mm 100 mm |
| 201 | Supply Installation, Testing and Comissioning of Unmanaged Switch Plug-and-play-easy setup with no configuration or no software needed, following Port fast ethernet-8 port 10/100/1000 MBPS auto-negotiation RJ45 ports. IEEE 802.3x flow control supports auto-MDI/MDIX, eliminating the need for crossover cables including making connection ete as required complete in all respect 24 port |
| 202 | SITC of IP Based 5MP Bullet camera: 1/2.8\\" or larger Progressive Scan CMOS Sensor with resolution (2560 x 1920) 30 fps Should Support H.264, H.265, MJPEG, Quad/Triple streaming profiles, Frame rate upto 1-30 fps, 120dB WDR, 2DNR/3DNR, BLC Camera should support Open standard to support ONVIF (PROFILE S. PROFILE G, PROFILE T), 1/1 Audio In/Out or better and 1/1 Alarm In/Out of better, onboard storage upto 512GB (SD card not included). The camera supports advanced Video Analytics (VA) including motion detection and alarm should be trigger on Tampering, Network disconnect. IP address conflict CCTV should have password protection, privacy mask, IP address filtering. Metal Housing, Vandal-proof housing, IP67, IK10, DC 12V & PoE, Complete wah Junction box for cable management Operating Conditions within -20°C to 60°C or better. The MAC address of Camera/NVR must be registered in the name of OEM Regulatory approvals include FCC, BIS/UL, CE CCTV cameras must be BIS Registered Cyber Security Certified by STOC as per lol SCS and meet the Essential Requirement (ER) issued by Meity for security. The CCTV OEM should have its service support center in Rajasthan 28/3 6/4/6/8 mm lens IR Range-50mtr or higher. |
| 203 | Suppon 11 264, H.265, MUPLO, Quad Triple streaming prefiles Frame rate upto 1-30 fps, 120dB WDR, 2DNR/JUNE, BLC Camera SITC OTP Based SMP Doone canена: 1/2.8\\" or larger Propese Scan CMOS Sensor with resolution (2560 x 1920) 30 fps Should should suppen Open standard to ONVIF (PROFILES, PROFILE G. PROFILE TL 1 Audio Inul ne better and 1/1 Alem bo Out or better, onboard storage upto 512GB (SD card not included) The camera supports advanced Video Analytics (VA) inckeling motion detection, and alarm should be trigger on Tampering. Network discomect. IP address conflict CCTV should Complete with Junction bes for cable management Operating Conditions within 20°C to 60°C or beter. The MAC address of Camera/NVR have password protection, privacy mask. IP addres litering. Metal Housing, Vandal-proof housing, IP67, IK10, DC 12V & Pof must be registered in the name of OEM. Regulatory approvals include FCC, BISA/L, CE CCTV cameras must be BIS Registered Cyber Security Certified by STQC as per loT SCS and meet the Essential Requirement (ER) issued by Meiry for security. The CCTV OEM should have its service suppon cemer in Rajasthan6/8 mm Lens more than 30 to 50 meter or above IR range |
| 204 | STIC of 32CH NVR for 2/5 MP cameras with woman 4 SATA HDD Support with minimum 40 TB Capacity (manumum 10TB Capacity per slet - Hant Disk Not Included), manmum HDAII output port, Videu comression 11:265/H.264/JPEG. 1/1 Audio In On. Preview Capability-Upto 4K, Plosback 6-channel samahancously, NVR should support minimum 320 Mbps throughput bandwidth 1160 incoming handwidthy, ONVIF compliance (Profile SG/T) Recording resolution up to 4K/8MP, minimum 2 USH Ports minimum 1 Tihernet Ports (RJ-45) 10/100/1000Mbps RAID 0/1/5/10 or better The system shall operate in 0°C to +50°C or bener with DIS, FCC, CE. The CCTV OEM should have its service support center in Rajasthan |
| 205 | SITC of 3.5\\" 4TB internal HDD for ectv recording capable for 24x7 operation, hdd rpm capacity shoud be 7200 rpm or better, Butler should be 512 MB as required of following size 6 TB |
| 206 | SITC of IP-PBX which is IP at its cure and act as a Umfied Consumunication System with IP switching technology and 100% non-blocking, configured for below mentioned. The system should be IPV6 ready, should have VoIP and Voice mail at its core 1 these modules should be mountable on the CPU. The system should be → Sig Ready, imbuilt Auto-attendant facility, Returned Call to Original Calier (RCOC) CLI based DISA (Mobile Extension) System, Should support SNMP martager for managing and monitor network, elements, audit network usage and detect network faults, should support SIP over TLS and SRTP, minimum 2 Gigabit Ethernet ports for LAN and WAN, built-in multi-party conferencing facility with 21 party in a single conference, minimum one RS232 ports for SMDR/PMS/CAS Interface The System have have capability to also act like Universal Media Gateway when required. The System should have facility of Conversation recording on Analog/Digital/il ports as well as on Mobile SIP Smartphones, UC Client application for Android, iPhone and on Windows PC. Power supply should be inbuilt and SMPS type with input ranges from 100-240 V AC, 47-60 112 OR 48VDC +15% The system must have Cenificanon TEC CE, FCC, ROHS48 analogue extensions, 04 PSTN Trunk Port, 12 Channel SIP PRI 04 Digital Port, 15 IP User License, 5 IP Softphone/mobile user |
| 207 | SITC of Line Card for required Analog/Digital/CO Extensions, compatible to8 Digital Extensions |
| 208 | SITC of Digital Phone/Operator Console with 240 x 64 of better- Povel Graphical LCD with Backlit, LED for |
| 209 | SITC of Type-1 IP Phone with 128 x 64 or better-pisel Graphical LCD, Extended SIP Protocol, LED for Call and message |
| 210 | Providing & Fixing of 240/415 V AC MCB with positive isolation of 10 kA breaking capacity (B/ CD iipping characteristic as per type of load and site requirement) 4 KV impulse withstand voltage, ISI marked IS 8828(1996)/conforming to IEC 60898-1 2002, IEC 60947-2 low watt losses, trip tice mechanism, energy limiting of class 3 as per IEC, munimum phase termination capacity of 25 sq min, conductor line load reversibility. IP 20 contact protection and Fitted in existing distribution board/sheets, mimonium electrical operation 20.000 upto 20 A rating. 10.000 upto 63 A. 5000 for 80 A & above rating including making connections, testing etc as required Single pole MCB (With B/C curve tripping characteristics)6 A to 32 A rating |
| 211 | Double pole MCB (With B/C curve tripping characteristics) 40 A rating |
| 212 | Triple pole MCCB (With B/C curve tripping characteristics) 50/63 A rating |
| 213 | Four pole MCB (With B/C curve tripping characteristics)40 A rating |
| 214 | 50/63 A rating |
| 215 | Providing & Fixing of 240415 V Gactory fited RCBO with overdad, sorn- creuit and earth leakage protection with IST marked (IS12640-27 conforming to IEC 61009-1, breaking tverfood, short cinctutk min Electrical operation 10.000 upto 63 A rating, minimont phase termination calabrying capacity 10 KA, provision forestillo bath existing distribution board/sheet including making connections, testing etc. as requiredTwo pole 30 mA sensitivity40 A niting |
| 216 | Providing & Fixing of Recessed surface mounting heavy duty horizontal type Double Door (Metal/Glazed / Acrylic) Distribution board with Metal end box made out from Galvanized steel/CRCA sheet, powder coated conforming te IS-8623-1 & 3/ IEC 61434-13 complete with 100 amp insulated copper bus harsherting link, bease neutral link with shrouds, brass earth linic, door earthing arrangement. color coded interconnecting wire set of minimum 100 spoon size and din bar masking sheet, making internal DB terminations with copper Hugs, Ferrules, detachable gland plate, including making connections, testing etc. as required.Metal door (single phase) 1k-09 and IP-43 with Metal end box 12 Wav |
| 217 | Metal door (Three phase) lk-09 and IP-43 with Metal end hox 6 Way (8 meomet 18 Outgoing) |
| 218 | 8 Way (8 incomer 24 Outgoing) |
| 219 | P&F metal clad Polyamide industrial plug top & socket unit with pin and sleeve type contact on porcelain/ bakelite hase in Recessed surface mounting heavy duty Enclosure made out from Galvanized steel/CRCA sheet powder coated conforming to IS- 8623-1 & 3 IEC 61439-1 & 3 (without MCB) including making connections, testing etc as required 20 amp. 12P+Ex 1 Module |
| 220 | Providing & Fixing of Recessed/surface mounting heavy duty Vertical TPN Distribution board with Metal end box with provision of incomer suitable for 3/4 pole MCCB and SP/TP MCB up to 63 Amps as outgoing made out from Galvanized steel/CRCA sheet, powder coated conforming to IS-8623-1 & 3/IEC 61439-1 & 3 complete with insulated 125/160/200/250 Amp. copper bus bar. color coded interconnecting wire set of suitable rating and din bar. brass neutral hors with shrouds, brass carth bor door earthing arrangement, masking sheet, making internal DB terminations with copper lugs, ferrules, detachable gland plate, including making connections, testing etc as required.Double door IP-43 & IK-09 with Provision of Incomer MCCB up to 125 A 6 Way |
| 221 | Providing & Fixing of IS1 marked (18,371) 6 amp surface type 3 pin ceding rose with CML no printed and made out from industrial grade Polycarbonate material, brass terminal & captive screws including making connection testing ete, as required |
| 222 | Providing & Fixing of ISI marked (IS 1258) batten/angle lamp holder with CM/L no. printed and made out from industrial grade Polycarbonate material, brass terminal & caplive screws including making connection testing etc. as required |
| 223 | Providing & Fixing of ISI marked (15 1293) 16 amp unbreakable 3 pin plug top having lamp indicator with CM/L no printed and made out from industrial grade Polycarbonate material, brass terminal including making connection testing etc. as required |
| 224 | Providing & Fixing of single moto tore electrone, cili bell/remote bell including makong correction testing eic, as requited |
| 225 | Providing & Fixing of 1St marked (IS bazy ding dongmaorat shine beli metaling making connection testing etc as required. |
| 226 | Providing & Frong of noodudar type switch bell push duly IM marked (15 1854) with UML no printed and made out of unbreakable and fore retardant virgin UV Stabilized Polycarbonate with brass sermunals and capuve screws & silver alloy contact tip with 11-20 rating minimum width of switch togglet PUSH PART) should not less then 20mm including making connections, testing etc as required 6. A bell push |
| 227 | 10. A one way switch |
| 228 | 16. A one way switch IM |
| 229 | 16 Ansp 2 Module switch With Led Indicator |
| 230 | 32 Amp 2 Module switch With Led lesbeator |
| 231 | Providing & Fiong of IS 1293 marked mosdular type lockable feature socket with CM/1, no. printed duly made out of unbreakable and fice retardant virgin poly carbonate with brasa terminals and captive wrews & silver alloy contact tip with IP-20 rating, including making connections, testing etc as requiredA 3 pin shuttered socket |
| 232 | 6/16 A shunered socker |
| 233 | 13 A flat pin mternational socket (Non 151) |
| 234 | Providing & Irving of modular type 100W Step Fan regulator duly IS1 marised (IS 11037) with CMUL no printed made out of unbreakable and fire retardant virgin pols carbonate with brass terminals and coptine screws & silver alloy contact tip with IP-20 rating including making connections testing etc as required5 step fan regulator 2 Module |
| 235 | Providing & Frong of 3 M Key card switch with I oad capacity 20 amp, Offume delay 30 Sec made out of unbreakable and fire retardant virgin poly carbonate, including making connections, testing etc as required |
| 236 | Providing & Fixing of following modular accessories, made out of unbreakable and fire retardant virgin poly carbonate with brass terminals and captive screws & silver alloy contact tip with IP-20 rating, including making connections, testing etc as requiredRJ-11 telephone jack single line |
| 237 | RJ-11 telephone jack Double line |
| 238 | USB Charger 2 A-IM with BIS mark |
| 239 | RJ-45 Cat 6 computer cack with shutter |
| 240 | TV. coaxial socket |
| 241 | Blanking plate |
| 242 | LED Skorting Foot Light 2 Module |
| 243 | Electronic Chine/Buzzer 2M |
| 244 | Modula MCB 6 A to 32 A DP |
| 245 | Providing & Fixing of following size mounting grid plates with cover plates made from fire retardent UV established high performance engineering plastic suitable for all universal metal boxes for front installation & removal direct fittype complete in all respect 1/2 Module |
| 246 | 3 Module |
| 247 | 4 Module |
| 248 | 5 Module |
| 249 | 6 Module |
| 250 | Prowling & Fixing of following size cover plates made from fire retardent UV established high perfonnance engineering plastie suitable for all universal metal boxes for front installation & removal direct fit type complete in all respect 1/2 Module |
| 251 | 3 Module |
| 252 | 4 Module |
| 253 | 5 Module |
| 254 | 6 Module |
| 255 | P&F Krone module with bose frame in the recess / surface made out of 12 mm thick sheet steel ben, front openable, having locking 20 Pairs |
| 256 | 50 Pairs |
| 257 | [5:35 PM, 7/20/2026] Himmat Saini: SITC of IP-42 and general construction continning to IS $623 1993, wall free standing flour mounted dust and vermin proofcompartmentalised cubical panel as specifications and Other parameters required as per point (a) (b), (cd), (el ifi. (gl.th) as below |
| 258 | supplying and fixing of Alteminam (IEC 60105 ISO 20%1.21 / Copper (IEC 60028) bus bar by means of SMC DMC type insulator, with short circat withstand capacity of 31 MVA for 1 Sec, high tensde nuts and bolts spring washers in existing panel including bending, cutting in required shape and size and colour coding with heat shrinkable PVC sleevesElectrolytre grade Aluminium bus bar 6010 gode |
| 259 | Providing & Fising ofIS: 13875 & IEC 61326/AEC 62053-22 conlirming LED Digital type (up to 500) V range Volt meter/Direct-Ammeter/ CT opertated ammeter/Irequency meter/KWII meter/Multi Function Meter / Power analyzer of class 1 accuracy of size 96mm x 96 mm including making connection by PVC insulated copper conductor with PVC sleeves / charinel etc as requiredThree phase AMP-HZ+PP+KW+KVA-KVAR TENERGY THD-4 THD-V & RUN HRS Meter |
| 260 | Providing & Fixing of Current Transformer confirming IS 2705-1 (1992) with secondary terminal and shorting Block with all necessary support in existing panel including connection ele, as required Current transformer Ring Type Tape Wound/Resin Cost Wound Accuracy C1, CT cathe and hunden as specified ISF-5. Cu cross section of secondary wire 1 Ssqmm (minintum), including all necessary support in existing panel including connection etc as requiredRing type tape wound CTCT Class 1, Ratio 800/5 to 1200/5, Burden 15 VA |
| 261 | Providing & Fixing of 110/220 V. unibody LED Indicating lamp IEC 60947 with integral circuit, IP 65 above panel & IP 20 terminal block. Approx. body dia for panel not less then 20 min, length min. 50mun, front LED cover dia min 27 mm, contact material phospher bronze for Led. PCB contacts shall be of brass (tin plated), impulse dielectric tested for 2.5 KV. Rated insulation resistance shall be 100 M ohm at 500VDC including connection ete as required Red/yellow/Green colour |
| 262 | Blue/white Colour |
| 263 | Providing & Fixing of Electrical insulating rubber mais confinning to 1515652/2006 with one side anti skid aberration marks and pasting the mat with synthetic rubber adhesive as required3.3 KV. class A 2 min thick with proof voltage 10 KV AC (rms) and BreakDown Voltage 30 KV AC (rms) |
| 264 | Providing & Fixing of self healing IP20 MPP type shunt capacitor (banks conforming to 15:13340-41/ IEC 831-1&2 OR IEC: 60831-1&2 in existing panel or parallel with load terminals, the capacitor shall be fitted with discharge resistors, pressure sensitive disconnector (PSD) and shall have dissipation factor less than 0.0025 at 50 Hz. Operating loss less than 0.30 Watt per KVAR Min over current capacity 18 times rated current & peak inrush current min 300 times of rated current, life expectancy greater than 100000hrs (temp class 25 D) in 440 V including making connections, testing etc as required.Heavy duty Three phase 440 V, 50 Hz cylindrical type capacitor (Bank) |
| 265 | Providing & Frong of 440 Volt 3 pole capacitor (AC 614) duty contactor with 3 no party make and post break ausulary contacts in series with quick discharge damping resistors reactors to limat the inrush curent as per 15/1EC 60947-4-1 2000, insulation sohage 1000V impulse withstand voltage & KV.Din rail mounting type including making connections, testing ere as required suitable for following саросту сераснor bank10 KVAR |
| 266 | 12.5 KVAR |
| 267 | 15 KVAR |
| 268 | 20 KVAR |
| 269 | 25 KVAR |
| 270 | Providing & Fixing of Electromechanical/degstal time switch having following day/week programme and minimum 100 hours reserve and ACT rating of 16-20 amperes including making connection, programming conforming to ILC 60730-1 and 60730-2-7 etc as requiredOne day reserve Electromechanical ive |
| 271 | SITC of 3/4 pole current lonting Moulded case ercuit breaker (MCCB) made of flame retardent & heat resistant material having following current rating, short circuit breaking capacity at 440/415 V, 50 Hz. 01. & S/C settings. conforming to 15/11C 60947 P-2:2003 with front face and centralised adjustable, trip free mechanisum, truc contact position indicator, designed for both horizontal & vertical mounting without any adverse effect on electrical performance, suitable for operation from 50 to 55 degree and without derating upto 40 degree, pollution degree 3, having positive isolation capability, push (test) to trip, irip time less then 10 ms under se condition, Breaking capacity les 100% leu U im; 8 KV. rated insulation voltage 690V provision for UVR shu: trip, earth fault trip. Joor interlock, pad lock & rotary handle ( to be paid extra) including making connections ete, as required. OEM shall have submit NABL/CPRI ERDA/ Imertek accrediated lab type test certificate3 pole MCCB With Thermal Magnetic releaseup to 100 Amp 10 LA. fosed OM. & fixed S/C setting |
| 272 | 4 pole MCCB With Thermal Magnetic release125 Amp, 25 kA. ahustable O/L & Fixed S/C setting, |
| 273 | 160 Amp, 25 kA adjustable O & Fixed S/C setting, |
| 274 | 250 Amp, 25 kA, adjustable 0/1 & adjustable S/C setting |
| 275 | 400 Amp. 35 kA, adjustable O/1. & adjustable S/C setting |
| 276 | Supply and fixing of following accessories for Moulded case circuit breaker (MCCB) compatible to main MCCB OEM as per PWD specification for electrical Works, conforming to IS/IEC 60947P-2 2003 including makingconnection ete complete in all respectExtended Rotary Handle |
| 277 | Spreaders upto 125A, 3 Pole MCCB |
| 278 | Spreaders for 250A 4 Pole MCCB |
| 279 | Spreaders for 400A 4Pole MCCB |
| 280 | Providing & Fixing of on load change over switch, front handle operated, four pole 415 V confirming to IS/IEC 60947-3-1999 includingconnections, testing etc as required in the following ratingOpen execution type400 A |
| 281 | Providing & Laving XMP modeed & PVC sheached Armoured Aluminium cabe confining to 15 700%p.tofilkV wah 14. Ciraóc electrohtic aluminum conhactive confimming to 15 8130 of purity 996 round/flar strip armuring of cables, Inner/outer sheath coefirewng to IN 11 in existing RCCHome/Stowevare PVC pipe open diceable trench/Cable tray (with calde tie) mchahing tewing commisswoning etc as required of 16.0 Sq. mm 4 core |
| 282 | 16.0 Sq. mm 4 core |
| 283 | 70.0 Sq. mm 3.5 core |
| 284 | 185.0 Sq. mm 3.5 core |
| 285 | Excavation of trench of size 75 con (Depth) s. 35 enw Width) for laving of suitable ne of LT cables tloter spacing between cables should not be less than 2. D) in ground with following procedure (a) Make a river sand bed of height 100 mm along the trench, (bt Lay the cable in the middle of the trench. (c) Provide river sand bed of height 100 mm on top of the cable, (d) Lay the profective Conumon burnt clay FPS Bricks of Clans designation 75/ Sand stone slabs of 50 mm thickness and 225 mm wide just above the sand bed vertically across the cable(e) Backfill the excavated soil leaving 300 mm from the Ground level, (filay the Cable warning tape and again bock-fill the remaming pormon of the trench upto the ground level and compacting the earth |
| 286 | Supplying and making end termination with heavy aluminium lugs (Pin/ring type) confirming to IS $309-1993 duly crimped with crimping tool PVC tape etc of following size6.0 Sq mm |
| 287 | 16.0 Sq mm |
| 288 | 70.0 Sq mm |
| 289 | 185.0 Sq mm |
| 290 | Supply, Fabricating & installing following sizes of perforated Hot dipped Galvanized iron cable tray (Galvanized thickness not less then 50 microns) with perforation not more then 17.5% in convenient section including horizontal and vertical bends, reducers ices,cross members and other accessories as required and duly suspended from the ceiling with Gl suspenders including Gl bolts & nuts, fastners. supports etc. as required225mm x 50mm x 1.6mm |
| 291 | SIF cable route marker with 10cm x 10cm x 5mm iluck or 10 cm dia G 1 plate with inscription thereon, bolted/welded to 35mm x 35mm 5mm angle iron, 60cm long and fixing the same in ground in CC (136) as required |
| 292 | PL of Double wall corrugated HDPE pipe confirming to IS 16205 P-24. Stiffness Class 750 N. Externally corrugated and having smooth surface inside with HDPE Coupler, Elbow, Tee at required Depth below the ground for laying cable of following Nominal Outer dia MFR Test report from NABL accrediated is to be submitted (Excavation of trench, CC launching, Back filling of Earth with compaction is to be Paid Extra) 75 mm |
| 293 | Plate Larthing as per 15 3041 with copper Earth plate of purity >95% of size 600mm x 600mm x 30mm by embodying 3 intr. below the ground level with 20 mm dia. G1. U class watering Pipe inchading all accessories the nut, bolts, reducer, nipple, wire meshed funnel, Heavy duty weather proof poly-propylene earth inspection chamber as per requirement of IS/AEC 62305 and tested as per IEC 62561-5 with lockable Jam free lid suitable for sate working losal 60 LN of round/ square size 250 mm, and Height 250 to 300 mm. and embodying the pipe complete with akernate layers salt and coke/ charcoal, testing of earth resistance for value of 5 ohms or less as required |
| 294 | SITC of Copper Bonded rod Earthing with high tensile strength (more than 600 N/sq min low carbon steel red molecularly bonded with Copper thickness (250 microns) and confirming to UL 467 of following size and length and as per point mentioned (a), (b), (c).(d), (e) below(a) Bore a hole of dia 100 mm of required length. Place the rod in the care (b)Earth enhancing compound to ensure the moisture content and electrical conductivity, 25 kg for 3000 nam. The compound shall be tested form NABI, accredited lab for low resistivity (less than 0.12 Ohun with carbon as a major content in accordance with IEC 62561-7 meter) & high conductivity is nature Connect the rod with copper Strip/onductor/Wire with suitable clamp mikle from tinned copper and SS 304 Bolt(d) Place Heavy duty weather proof poly-propylene carth inspection chamber as pej requirernent of IS/IEC 62305 and tested as per IFC 62561-5 with lockable Jam free led suitable for safe working load 60 kN of round/square size 250 mm.and Height 250 to 300 mm(c) Testing of earth resistance for value of 5 ohins or less as required(1) Test certificates for confirming above standards from OEM is mandatory17.2 mm thick and 3 Mir. Long |
| 295 | strip DMC Insulator including riveting soldering welding, Jouning shall be done by overlapping double the width of strip and with 2 set of Brass (for Cu stop)/Gl (forGi Strip) ma boli & spring washer spaced at 50cm making connection ere as required25mm x 3mm.copper stop |
| 296 | 25mm x 6mm G1 (Hot Dipped) Strip |
| 297 | Supply & Laying following size carth wire in horizontal or vertical run in ground/surface/recess including riveting, soldering saddies, making connection with GLCu punty purity>95% thimble ete as required10 SWG G1 (Hot Dipped Wire |
| 298 | Supply & Laying following size' B' class, G.1. Pipe continning to 18 1239 P-1(2004) with accessories like bend, socket etc for laying earth conductor/strip/ cable in ground/ sau face/ recess as required. (Earth Excavation will be Paid Extrai100 mm dia |
| 299 | Supply & Foxing of phenolic laminated bocad of 60 mm thick for fresh air fan/exhaust fan up to size of 300 man on existing window frame including cost of board, cutting of hole Nut bolts ete, as required. |
| 300 | Installation testing and Commissioning of ceiling fan (any size) mcluding wiring the down rod up to 30 cm with 3 x 15 sq min pve insulated flexible copper conductor. Cotter pin, rubber grommet making connection testing etc as required With regulator |
| 301 | Providing & Fixing BLDC technology step regulator compatible ceiling fan, with aluminium body & aluminium blade, poser factas not less then 09 following service value (CMM/W), with following air delivery, speed 350 RPM (tolerance as per IS 374 2019 THD less then 10%, copper winding with class of Insulation T complete with with secondary support safety cable (steel rope), Joun rod up to 30 em, coner pin, shackle ka with 3 x 1.5 sq mm pve insulated flexible copper conductor making connection testing etc as required1200 min sweep with An delivery / 230 CMM and Service Value 8 20 |
| 302 | Providing & Fiving of 400 mm Sweep BLD technology Oscillating type Wall mounting/Pedestal type fans with Three speed. ON and OFF position. Double Wall bearing with front and back 120 or more ribs guard, Three no blades, noise level should be JB. including fixing with anchor bolts, making connection testing etc as required: (With Remote) 75Wall mounting type with Service value 2.0 CMM W. Man. Air Delivery 71CMM |
| 303 | Providing & Fixing of Heavy duty capacitor start, copper wound Double ball bearing 900/1400 RPM single phase Exhaust fan conforming to 15 2312 marked in existing opening including making connections testing etc as required300 mm sweep(900 RPMI |
| 304 | 450 mm sweept 1400 RPM) |
| 305 | Providing & Fixing of Vertical BEE 5 star rated)/Horizontalt BEE 3 star rated) storage water heater with outer casing made of Engineering Plastic sheet (Upto 25 Lir)/Metal rust proof Body (35 & 50 Lit), Glassline/Titanium Enamel coated Pressure Pump Compatible 8 bar pressure Inner uk, Glass Line Coated, mineral filled heating element, siem type, snap action adjustable thermostat Dual indicating lamps Injected PUF insulation, Multi Function Valve ete as required held in position with 2/4 no. 10/12 mm anchor Fastener, duly wired with 3 core 2.54.0 Sqmm PVC insulated & sheathod copper conductor and 16 A 25A three pin plug top including making inlet, outlet Flexible alloy connection, testing etc, as required10 L |
| 306 | 25 Ltr |
| 307 | SITC of IP20 SMD Mid Power LED batten type integrated light fixture made from Powder coated Extruded aluminium housing wath in built driver System lumen efficacy 110 lm/Watt output only at CW (5700K to 6500K) internal surge protection of 4.0 KV with Short & Open circuit protection, THD <10%, P. F20.95, CRI-80, life time of minimum 50000 Burning Hours with, 70% of intial Lumen maintaned till life ends CCT 3000°K/4000°K/5700K/6000K/6500°K (As per ANSI Bin) as required 1170mm(+/-10%)LED batten with min lumen output 2200 Im |
| 308 | SITC of IP-20 LED Recessed Surface Mounted, Round Square backlit & SMD Mid Power LED Downlight with power coated die cast aluminum housing with UV Stabilized non yellowish Diffuser with BIS compliance 4.0 KV surge protected Isolated driver, with Short & Open circuit protection input 320VAC-48 hr protection, input 350VAC-2 hr protection), having efficiency> 85% System Lumen efficacy of 2 110 Im/watt,at CW (5700K το 6500K), THD <10%, P120.95. CRI>50, life time of minimum 50000 Burning Hours with, 70% of intral Lumen maintaned till life ends CCT 3000°K/4000K/ 5700°K 16000K/6500°K (As per ANSI Bin) as requiredRecessed MountingMinimum lumen output 1300 Im |
| 309 | Minimum lumen output 1600 Im |
| 310 | Surface Mounting (with extruded alumn. Housing) Minimum lumen output 1300 Im |
| 311 | Minimum lumen output 2400 Im |
| 312 | STIC of 1920, 2x2 LED Surface Recessed mounting backlit & SMD Mid power type LED Light fisture not less than 15 nam housing depth made from CRCA sheet steel housing, high punty transmissivity UV stabilized Non-yellowish diffuser for uniform light distribution operating voltage range 140-285 V. IIV cuto/T-LV cutoff should be 300-100V High efficiency with 4 KV internal surge protection BIS certified isolated driver having efficiency 85%, with Short & Open circunt protection (input 320VAC-48 hoursprotection inpot 350V AC-2 hours protection) (Integral with liglu fisture) System huamen efficacy of 120 Im War: THD 10 12095,CRI>80, life time of mininum 50000 Burning Hours with 70% of intial Lounen maintaned till life ends CCT 3000°K 4000K/5700K/6000K. 6500°K (As per ANSI Din) as requiredRecessed MountingMinimum lumen output 4800 Im |
| 313 | SITC of Suspended mounting 1966 IK08 rated Integrated High power LLD Wellglass light fisture made from Pressure Die Cast Aluminius housing, potted driver, Eye bolt for mounting PC elear Opal Diffuser, system lumen efficacy 2130 lin/Watt output only at CW (5700k to 6500K), THD < 10% p12095.CRI>70, life one of minimum 50000 Burning Hours with 70% of intel Lumen maintaned till life ends, CCT 3000°K/4000K 5700°K/6000K/6500°K (As per ANSI Bin), maximum power consumption should not more than the specified rating surge protection 4 KV mbuili & 10 KV external inside frcture as reamedMinimum lumen output 4550 Im |
| 314 | SITC of energy efficient energy saving IP 20 LED direct retrofia Bulb in existing holder or fixture as required with system lumes efficacy2100 lm/Watt output pl 0.95 CRI >70, minimum life time of minimum 25000 Burning Hours with 70% of mtial Lumen mamtaned till life ends CCT 3000°K/4000°K/5700°K/6000K/6500K (As per ANSI Bin) as required9 Watt |
| 315 | SITC of IP65 IKOS rated Integrated SMD Mid power LED bulk head type light fixture made from Pressure Die Cast. AL. housing suitable with anteeral demersvaten lumen efficacy>120 lm/Wat.cuanut.ons CW 15200K to 6500K) THD <15% Minimuin lumen output 1200 Im |
| 316 | Providing & Fixing of IK08 IP65/IP66 protected LED Up-Down Luminarie Wall Surface mounting made of powder coated die cast alluminiurn housing with with UV stabalized PC diffuser. The System level Luminous efficacy 80 Lumen/W COB LEDs is to be used. System CRI>70, CCT: 3000/4000/6500 K. The integral electronic driver must be potted & has a unique BIS R number constant current and Internal/external surge protechon device of min. 4KV(L-N) and efficiency 85%, PF>0.9, THD<10% and input Voltage range of 140-270V AC 50Hz. System life of 50000 Burning hours with 70% of Initial Lumens maintamed Light output in Cool white or Warm White Colour as per engineers choice LED driving output current <750mA as requiredMinimum lumen output 1300 Im Up-Down Luminary |
| 317 | Minimum lumen output 2150 Im Up-Down Luminary |
| 318 | Providing and Laying RCC Foundation for Octagonal Conical Street Light poles as per Drawing attach at Table P-05 with Following ProcedureA) Excavation of Pat for Foundation Size upto required depth from Ground levelB) Dressing of Pit and Dry stone pitching 200 mm thick including supply ofC) Providing and laying in position cement concrete of M-10 grade of 75 mmD) Reinforcement for R.CC. work with TMT bars including straightening, cutting bending, placing in position and binding allE) Centring and shuttering including strutting, propping ete and removal ofF) Providing & Fixing of 2 no Required Size PLB HDPE Pipe & Foundation Bolt with template as per OEM ReconumendationsG) Providing and Laying. Reinforce cement Concrete of M-30 grade in Footing and Pedestal inchading Curing the foundation for minimum 711) Providing and Fixing Nosing Angle 25 mm x 2.5 mm x 3mum with 2 no of Pole Foundation for Octagonal pole from 3 Mtr. To 6 Mtr |
| 319 | Pole Foundation for Octagonal pole from 7 Mir. To 9 Mtr |
| 320 | STC of 30 Watt speaker with taping facdity having frequency range of 6511-20kHza(-10db) with power handing of 200Watt continuous and inore than 350 Watt speak ete complete as required |
| 321 | Supply & Vistallaben of 240 Watt Mixer Amplifer Unit for providing a crimpeall or clear music with 4 microphone/ line inputs plus music wowoce input, announcement only output, 3 wire volume override, with Mains power supply 230 VAC +10%, 50 Hz reduced power at lowes marnst, Inrush current 20 A. Power consumption 120W, Frequency response (Line) 80 Hz to 18 kliz (+13 JB -10 dB rel rated output) Frequency response (Mic) 80 Hz to 18 kitz(+1-3 JB -10 dB ref rated outputi Distortion |
| 322 | Providing & Fixing of IP-65 Protected LED avsation elbstruction light luminaire comprising of die cast aluminium alloy housingwith Polycarbonate enclosure having more than 200 No's Low Power LED's having minimun pover consumption 15 watts complete in all respect aviation obstruction LED light luminaire 12/15 Watts |
| 323 | Providing & Fixing of IK07 IP65 protected Top Bottom mounted LED Post top Luminarie top & bottom inade of single piece construction powder coated die cast alluminium housing with UV stabalized Clear/frosted Polycarbonate diffuser and Aluminium anodised with powder quoted reflector The System level Luminous efficacy 80 Lumen/W SMD LEDs is to be used, System CRI-70, CCT 3000/4000/6500 K. The integral electronve driver must be potted & has a unique BIS R number constant current and Internal external surge protection device of min 4KV(L-N) and efficiency 85%, PF>0.9, THD 10% and imput Voltage range of 140-270V AC at 50Hz System life of 50000 Burning hours with 70% of Initial Lumens înaintained LED Driving out currem <750mA as requiredMinimum lumen output 2800 lin Post top Luminarie |
| 324 | Providing & Fixing of IKOS IP-66 protected high power LED flood light system with single piece Pressure diecast aluminiom houung toughened glass with suitable lenses on LED integrated lens diffuser to achieve various beam angles, of high power LED of 3 to 5 watt cach Integrated metal case potted driver as a unique BIS R number (as per IS 15885) having efficiency more than 85% and in compliance to BIS certified and Trade mark certificate Fitting & driver both have separate BIS R number) The System level Luminaire efficacy 130 lm/ wt. LED drner Input Voltage AC 120 to 270 V AC with High voltage Cutoff 300 V AC & Low Voltage cutoff90 V AC and Auto resetting Safety Power Factor 0.95 THDI) <10% LED driving output current 750mA. driver should be Phase to phase protection of 440 V for 4 Hrs. Electrical Connector. Surge Protection Min>-4KV internal and 10KV external but inside driver compartment System lite Jof 50000 Burning hours with 70% of Initial Lumens maintained CRI>70 and CCT 57006-355K المصعد High Power LED Flood Light Minimum lumen output 13000 Im |
| 325 | Providing & Foang of IKUS, IP 66 protected LED Street Light Luminaire on existing bracket/pole Fixture made of powder coated single piece pressure die cast aluminum material with heat dissipation fins on housing and secondary lens on each LED/ integrated lens diffiner without cover & should be High power LED of 3 to 5 wait cach The System efficacy-135 Im wt and integrated metal case potted driver & has a unique BIS R number (as per IS 15885) with Input Voltage AC 120 to 270 V AC with High voltage Cutoff 300 V AC & Low Voltage cutoff 90 V AC and Auto resetting Safety Power Factor20.95 driver Efficiency >85% THD) <10% Humidity 10% to 90% RII Working Temp SC to 45C LED driving output current 750mA. The luminaire shall be BIS certified (Fitting & driver both have separte BIS R number) and Trade mark certified Life Expectancy Equal or more than 50000 buming his with Minimum 70% lumen maintened CRI 70 and CCT 5700K +355k Surge protection shall be min 24KV internal and rain 10 KV external inside driver compartment, driver should be Phase to phase LED Street Light fixture with Minimum henen output 8100 Im |
| 326 | Supply and erection of Galvanized Iron pole with galvanizing done in single dipping (Average coating thickness Mimiman 65 Microns) continuously tapered poles having Octagonal/Circular/ Conical cross-sections designed to withstand the maximuen wind speed as per IS 875, The pole shat shall be made from sheet steel (HT Steel Conforming to grade $355J0) and confirming by BSEN 10025 and shall be continuously tapered with single longitudinal welding. There shall not be any circumferential welding. The welding of pole shaft shall be done by Submerged Are Welding (SAW) process, pole shafts shall be provided with the rigid flange plate of suitable thickness (Fe 410 conforming to 18 226/15 2062) with provision for fixing 4 ne foundation bolts, The base plate shall be fillet welded to the pole shaft at two locations te from inside and outside The octagonal Peles shall have hinged lockable door of approximate 500 mm length at the elevation of 500 mm from the Base plate with bakelite sheet having 6A SP MCD and 16 sqanm stud type connector (4 nos) insade the pole at door opening for cable connection of following length and dimension as per table P-01 for Octagonal & P-02 for Conical with base plate and foundation bolt on the Existing cement concrete foundation. To ensure quality of product it's entire manufacturing process starting from sheet cutting to galvanization sould be done under one premises.Poles with Octagonal Conical Cross Section 3 Mtr |
| 327 | 8 Mtr |
| 328 | STTC of Radial mixed flow water and anti-corrosive liquid filled submersible motor pump sets suitable for 100/150mm dia borewell The sare of adopter fixed on top of the motor should exceed the top of coupler for safegaurd the coupler. The job includes labour part of lowering of riser pipe GL/HDPE with rope, cables & pump, installation of complete fitting and accessories, joiming of electrical cables up to Starter All labour for testing of submersible pumps set and supply of water to water mains, complete in all respect100 mm diameter Submersible pump shall have following HP Rating, phase, 2.0 HP. 1-0, (7-95)Mr. (55-22) LPM |
| 329 | SITC of IP 54 OEM Fabricated DOL/Star-Delta Starter panel with switchgear selection as per Type-2 Coordination Chart and made out from 1.6 mm thick powder comed CRCA sheet, enclosure comprising of over load protection relay, short circuit & single phasing protection(for three phase pumps), Illuminated ON/OFF push buttons, arometer, voltmeter, indicating lamps, 2P/4P MCB etc. suitable for following rating motors complete in all respectFor single phase Submersible/Monoblock pump2.0 HP to 3.0 HP (DOL starter) |
| 330 | Providing & Fixing of IS 4985-2000 Class 4 (10 Kgf/Sqem) UPVC drisin water piping with fittings (15.7834 & 10Kgf/sqcm) like elbow, socket, Tee, solvent cement jointing, support with MS hanger on ceiling or recessed in wall with chasing & plastering with 6 min thick closed cell elastomeric nitrile rubber unsulation inclukling leakage testing ete as required of following Nominal120 mm |
| 331 | 25 mm |
| 332 | Making hole in stone masonary/RCC wall/RCC slab with core cutter for accomodating refrigerant pipe drain pipe/ MS pipe/ cables ete of following dia100 mm dia per running inch length |
| 333 | Supply & foxing MS powder coated stand suitable for 10/15/20 Troutdoor type |
| 334 | Supply & foxing MS powder coated stand suitable for 2.5/3.0/4.0 Tr outdoor type of Spla/Ductable Tower AC All as per pre approved by Engineer in charge |
| 335 | SITC of Interconnecting refrigerant copper pipe for split/Dactable Casselle AC of DHL Grade C12200- ASTM D68, B75, chemical |
| 336 | SITC of following diagonal size profesional Display, 4k Resolution Brightnest Typ 1 440 ni and above. Contrant Ratio 2000 1 and above. Viewing Angle(TUV)-178/178, Respome Tune(G-to-G) Rins, Input RCB- Analog D-SUB, Valeo-HDMI 2.0 (2) HDCP-HDCP 22. Audio-Stereo mini Jack, USB-Only F/W upgrade, Oupats RGB-DP1 Loop natt Audio Stereo mine Jack. External Control- RS232Crin/out, RJ45, Extermal Sensor Detachable typetIR Ambient) Operation Hour 247 monesting bracket etc as required43 (for Rooms) |
| 337 | 55\\" (for Camera duplay dinning Room) |
| 338 | SITC of following capacity BIS certified Phase Input. Phase Output advance DSI controlled IGBT hased rectifier Online UPS with 0.99 Input power factor &0.8 Output factor, having Input voltage & frequency range of 180-300V on full load/110-300V on 60% load & 50 Hz-5% and output voltage & Frequency of 230V+/-1% & 50 +0.1 Hz. Overloading of 105-1104 10 mins, 111-130% 2 mins 131-150% 30 sec, THDv of 3% for Linear & 5% for Non linear load UPS should have LCD display showing load level, Battery Voltage Level, Input & Output Voltage, Input & Output Frequency UPS should have protection from Input High Low Over Lood Short Circuit, Over Temperature and give audible alarms on Battery Mode. Low Battery Fault Over Load & Bypass Mode SMF Batteries of 12V VRLA for 30 nun back up with MS Rack and necessary cable for UPS to Batteries Installation UPS should have CE, ROHS, IEC62040-1,283 compliance and should have QR code which should contain drawing, test report OEM mural Geo-Tag of manufacturing location Etc as required.3KVA UPS with 3024 VAH Battery |
| 339 | Supplying and drawing flexible/stranded bare copper conductor, PV/XLPE insulated, overall aluminium mylar tape shielded ATC drain wire and outer PVC sheathed industrial Instrumentation (shielded)cables voltage grade 300/500 V as per BS EN 50288-7 in existing surface or recessed PVC MS conduit/casing capping/Cable tray/Open Duct making connections, testing ele as required. OEM must ensure that the cable is tested for complaince, either through their in house laboratory accrediated by NABL or by any Govt. laboratory accrediated by NABL and the laboratory's scope of accrediation should cover the requirementsand testing procedure as per IS 10810Un Armoured4 core x 2.5 So min |
| 340 | Supply, Fixing and testing of following capacity IS 8448 marked wall mounted stabilizer having output voltage variation from 200 V to 250 V+-5%) with input voltage variation from 170 V to 260 V, time delay facility from 2 to 4 minute and high cutoff at 270 V with providing of 16 Amp 20 Amp Industrial plug top making connection etc complete in all respect5KVA |
| 341 | Extra amount of other work |
| 342 | Supply Installation. Testing and Commissioning of Inverter type Air cooled Hi Wall split type Air conditioners complete with Indoor unitiIDU), Out door unit (ODU), surface/concealed copper Refrigerant piping with insulation (closed cell elastomeric nitrile tubber tubular pipe section) upto 3 Mir (IDU to ODU), copper power cable upto 3.5 Mu (IDU to ODU) ve drain pipe R-32/R-410/ R-407 Green Reftigerant, wireless Remote control, suitable for working between 180-260V with low & high voltage cutoff and 50 hz.1 phase AC supply capable of performing cooling, dehumidification, air circulation of following capacity with Scroll/rotary compressor The system shall be able to deliver 100% of the rated capacity up to 42 Degree Celsius ambient temperature. Min 3 year Original Equipment Manufacturer (OEM) warranty both compressor and Printed Circuit Board (PCB) Must comply Electrical cable IS 694 or IS 9968 temperature sensing control IS International Electro technical Commission (IEC) 60730, herinebe compressor IS 10617, heat exchanger I5 11329, capacitor IS 2993 and motor 15 12615. Complete as per specification and IS 1391 Part II 2023. The system shall be able to operate up to 50 degree C (out door ambient temperature)Cooling capacity 6800-7000 Watt, ISEER not less then 3.8 |
| 343 | Supply, Installation, Testing and Commissioning of Air Cooled Floor standing Tower type split Air conditioners complete with Indoor unst(IDU), Out door unit (ODU), surface/concealed copper Refrigerant piping with mulation (closed cell elastumeric nitrile rubber tubular pipe section) upto 3 Mte IDU to ODU), copper poser cable upto 3.5 Mtr (IDU to ODU), R-32/8-410 Green Refingerant, wireless Remote control, suntable for working between 415 V +/-10%, 3 phase 50 Hz AC Supply with low & high voltage cutoff and capable of performing cooling, dehumidification, air circulation of following capicity wah Scroll/rotary compressorCooling capacity 10400-10500 Watt. ISEER not less then 30 |
| 344 | Supply Installation, Testing and Commissioning of Inverter type Air Cooled Cassette type Air conditioners complete with Indoor unit(IDU), Out door unit (ODU), R-32/R410A Green Refingerant, wireless Remote, inbuilt drain penp, suitable for 400/230V, + 10% 50 Hz 1/3 phase AC supply, capable of performing cooling, dehumidification, Air circulation, filteration & ventilation of following capacity with Scroll /rotary twin rotary compressor etc, complete as requiredCooling Capacity 10500-11000 Watt ISEER not less then 3.5 |
| 345 | Supply & Fixing of CO2 type Fire Extinguisher conforming to IS:15683.2018, charged with CO2 gas (purity 99.7% conforming to IS 15222), Powder coated Internal & External Surface Manganese steel ISI marked as per IS 7285 cylinder body, Wheel type Forged brass release valve ISI Marked as per IS 3224 with Inbuilt safety release device (Fusible plug and Rupture Dric Type). 10 Mir Metal wire braided hose having minimum bursting pressure of 140 Kgf/cm2. Horn with metallic thread connection, QR code for Product Traceability, including Fixing on wall with suitable Anchor Fasteners as required of following capacity Test Certificates of all the Parameters along with Hydro test & Burst test (For Cylinder Body) Certificate from OEM/External NABL Accrediated Lab is Capacity 3.0 K |
| 346 | Supply & Fixing of Dry Powder Agent (as per IS 4305:2019), ABC type Fire Extinguisher (Stored Pressure type) confonning to IS 15683.2018 Powder coated Internal & External Surface Deep drawn cylinder body of Mild Steel CR2 grade conforming to IS: 513, Squeeze grip Forged brass release valve with Inbuilt safety release device, Diaphragm Type, 0 to 28 har range pressure gauge, 450 mm long EPDM discharge tube, QR code for Product Traceability including Frxing on wall with suitable Anchor Fasteners as required of following capacity Test Certificates of all the Parameters along with Hydro test & Burst test (For Cylinder Body) Certificate from OEM External NABI. Accrediated Lab is to be submitted 6 Kg |
| 347 | P&F Indiari type white glazed Vitreous china 1st quality W.C orina pon(15 2556 Mark) with 100 min vitreous china Por 5 trap including cutting and making good the wall and floorSize 580x440mm. |
| 348 | P&F Low level Flushing Cistern of 10 titres capocity (15: 2556ack) Ofapproved make with complete fittings C.1 brackets duly painted, brass ball cock, with ball. (15 1703 mark) complete includung cutting and making pood the wall |
| 349 | PVC with PVC bend as per IS 7231P&P European type wiine glazed vitreous china 1st quality Double syphonic WC (IS 2556 Mak) with Por Strap including cuting and making good the wall and floor |
| 350 | P&WVC Wash barin ist quilos IN 2558 Mak) of spyoned make with Cf breskate duty pat 15CP.Pilar cock 14 Mark & 33 mm CP. Irass waste coupling of approved make PVC Waste pipe with PVC net 32 mm complete chating cutting & making good the wallSize 550 mm x 400 mm |
| 351 | Size 610 max 510 mm |
| 352 | Add extra for using 25muit Gl waste pipe instead of PVC warte pipe |
| 353 | P&F Bevellel olpe Mincemaree wuh teak wood tipping around of special plans of approved make in podneten of Engineer-in-chargecevaplete with em thack cial phy bese fixed te wooden soens & washersother Stres |
| 354 | N&F waste Pipe with all fitting PVC with UP. 40 mm dia |
| 355 | P&Flequin WVC Urmal (15 2556 mars) with 23mm dis (6.1 wade pope, dome watt couplings concealed non tractats or screws ale cumyteteFlat Back Large Hall stalls 10 400 x 80 |
| 356 | Automatic Hoshing Cotein of first quality (IS 14 marki of approved make fating suphon with copper tube, CT brackets complete including cutting and making good the wall WVC (as per IS: 2556) 10 hiresP& Bib Cock (IN 8931 Mark) Superior quality of approved make PVC heavy duty, 15num nominal bore |
| 357 | PAF Marble Urinal Partition slab both sides polubed of approved design cut from marble size 900x600mmMakrana Adanga of Raj Napar 45tQuality White or Andle Indo-Italian marble |
| 358 | P& ECP. brass Urinal Flush Pipe set complete with flanged brackets of approved makeFor 1 Urmal |
| 359 | CP Brass fittingsP&F 15 mm. Dia Connection Pipe of approved quality make: PVC pipewith CP Brass nuts upto length, 450 mm |
| 360 | PA FCP Health Faucet with 1Mu Long Tube & Hook of approvedmake and heavy as per direction of Faganser-inChange |
| 361 | P&F Inlet Connection (Angle Valves) Superior quality, of approvedmake, for Wash basm. Gyser eleCP Tuiet connection 15mm Brass (IS: 8931 marked) |
| 362 | Providing & Fixing Premuan quality Bottle trap internal portion 32mm size 250mm long wall connection pipe & wall flange as per approved by Eng |
| 363 | P&F Towel Rail or Ring of approved quality makeCP brass |
| 364 | brass Towel Rail elbow type with conceded screws size 450mm Heavy duty) |
| 365 | P&Grating of approved quality make(ko) Square 150 x 150 x 8mm (Anu Cockroach) |
| 366 | Providing and fising Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for bot & cold water supply including all CPVC plain & brass threaded fittings v'e fixing the pipe with clamps at 100 m spacing. This includes jomting of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge (Concealed work including cutting chases and making good the walls ete20mm dia nominal outer dia pipes |
| 367 | 25mm dia nominal outer dia pipes |
| 368 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having therinal stability for hot & cold water supply inchaling all CPVC plain & brass threaded fittings ve firving the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge timermal work Exposed on wall32mm outer dia pipes |
| 369 | 50mm outer dia pipes |
| 370 | Supply & fixing G1 Union ISI marked in G1 pipe line as required complete in all respect of size20mm dia nominal bore |
| 371 | 25mm dia nominal bore |
| 372 | 50mm dia nominal bore |
| 373 | P&F Full-way Valve (IS 778 Mark) or wheel valve of approved makeGunmetal 25mm nominal bore |
| 374 | P & F PVC Storage Tank ISI Marked (IS 12701) indicating the BMS license Nol, of approved make with cover, 25mm dia IM long G.1 over-flow pipe & 25 Cin long wash out pipe with plug & socket, including making connection ete complete of approved design 1000 litrescapacity |
| 375 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings ve fixing the pipe with clamps at 100 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge (Internal work Exposed on wall)150 me nominal size |
| 376 | P&F Full-way Valve (IS 778 Mark) or wheel valve of approved make (do-) 50mm nominal bore(-do-) 50mm nominal bore |
| 377 | Providing, lowering, laying, aligning, fixing in position and jointing in pipe line CI Kinetic Double Air Valves as per IS 14845 of following dia (including jointing and jointing material), including all material, labour, testing and commissioning as per TechnicalSpecifications and as per direction of Engineer a) 80mm dia |
| 378 | SITC of Dewatering Submersible Motor Pump set, motor should be IE2 class as per IEC 60034-2-1: 2007, IEC 60034-30 2008 & 1512615:2011 with SS Impellor, body, shaft, mechanical seat etc as required. Pump shall have following HP Rating, please. Head, cunimum Discharge respectively complete in all respect OEM shall have submit NABL CPRI ERDA accrediated lab type test certificate before execution. All as per pre approved by Engineer in charge. For additional technical parameters of products work, refer Авоемe \\"A\\" attached with thus BSR3.0 HP 3-0 (5-20)Mr (910-120) LPM |
| 379 | P&F Sand-cast Iron (SCT) Pipe (IS: 1729mark) of approved make in wall or in floor with MS holder bat clamps in 10 X 10 X 10 Cm M 15 grade concrete Mocks, joints filled with CM 1 4 with spun yarn including cutting holes and making good the wall100mm dia |
| 380 | 150mm dia |
| 381 | P&F SCI Fittings (IS 1729 mark) in CM 14 with spun varn100mm-do-Offset |
| 382 | Socket |
| 383 | D/door Y-Tee |
| 384 | Cowel |
| 385 | door cross |
| 386 | 150mm-do- tee |
| 387 | Construction of septic Tank in all types of sod with 40 Cem thick masonry in CM 16, 15 cm thick CC bed of 15:10, M-15 grade CC floor & RCC slab covering with M15 grade ce floor, 50 mm thick stone slab partition walls, 20 mm thick plaster in CM 1.6 tinished with neat floating cement, 4 Nos stone foot rests of approved design two No 450 min dia Each Ferro cement cover with frame. earth work etc complete as per approved drawing including duposal of surplus earth within a lead of 50 MirSize 400 x140x150 cm (for 50 users) with 115 mm thick RCC (M-20) |
| 388 | Construction of soakage well in all type of soil with 300 mm thick dry masonry, top and bottom 300 mm course in CM 1680mm thick stone slab, joming of slab im CM 13, Ralthal, Kharanje, 40 mm thick M-15 grade CC fhoring earthwork complete as per approved drawing including disposal of earth within a lead of 50 MuSize 300 Cin dia outside & 300 Cm. depth |
| 389 | onstructing brick masonry road gully chamber 50x45x60 cm with bricks of class designation 75 in cement mortar 1411 cement: 4 course sand) including 500x450 mm precast R.CC horizontal grating with frame complete as per standard designWith Bricks |
| 390 | Constructing brick masonry road gully chamber 110x50x77.5 cm with bricks of class designation 75 in cement mortar 1:4(1 cement 4 coarse sand) including 500x450 mm precast RCC horizontal grating with frame and vertical grating compiete as per standard designWith Bricks |
| 391 | Providing & Fixing of ward robe shutters made out of 19mm thick BWP block board ISI of superior quality make with following details: Front side finishing with 1mm thick superior.quality mica approved make and 0.8mm thick approved shade mica in the inner side. Covering with teak wood beading 25x12mm all the sides of shutter & 35x12mm on outer frame for making good the wall joint including heavy brass S.S. fittings (Handle 200mm 2 Nos. Tower Bolt 150mm 2 Nos., Brass Lock 1 Nos., Magnetic Catcher 2 Nos., Brass Hinges. 75x40x2.5 mm 6 Nos, SS Hanger Rod 20mm dia) complete as per drawing and design approved by Engineer in Charge |
| 392 | Supplying and fixing in walls machine cut and polished stone shelves, tands and in CM 1:3 with machine cut edges: Kota stone minimum 30mm thick. |
| 393 | Providing and fixing 14 mm thick Acoustical with fine fissured tiles/ Mineral fibre high density tiles with butt edges false ceiling tiles of size 595x595 mm in true horizontal level suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanized @ 170 gsm/sqm.) consisting of main \\"T\\" runner with suitably spaced joints to get required length and of size 24x38mm made from 0.30mm thick (minimum) sheet spaced at 1200mm center to center and cross \\"T\\" of size 24x25mm made of 0.30mm thick (minimum) sheet, 1200mm long spaced between main \\"T\\" at 600mm center to center to form a grid of 1200x600 mm and secondary cross \\"T\\" of length 600mm and size 24x25mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600mm panel to form grids of 600x600mm and wall angle of size 21x21x0.30 mm and laying false ceiling tiles of approved texture in the grid including, wherever, required, cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main \\"T\\" runners to be suspended from ceiling using Gl slotted cleats fixed to ceiling with 6 mm dia and 50mm long dash fasteners, 4mm Gl adjustable rods with galvanised level clips spaced at 1200mm center to center along main T, bottom exposed width of 24mm of all T-sections shall be pre-painted with polyester paint, all complete at all heights as per specifications drawings and as directed by Engineer-in-Charge. (The tiles should of 90% RH avg. NCR 0.55 light reflectance> 80% thermal conductiveity K = 0.052-0.057 w/m K colour white. Fire performance class 0/class I(BS 476) with warranty against sag) |
| 394 | Providing Solid PVC false Ceiling consisting of 600mm x 600mm, 5mm (±0.25) thick Plain embossed PVC sheet of Density 600 Kg/Cbm Manufactured by an ISO-9001-2015 certified Company, used as panel insert in a frame work made using powder coated aluminum T- section of sizes 1\\" x1\\"(25x25mm, 19 gauge or 1mm thick) in square pattern of grid sizes of 2'x2'(600x600mm). The aluminum framework is supported from the ceiling with the help of 'J' hook and G.I. wire/6mm M.S. rods of required sizes to maintain proper level etc. The aluminum framework is supported on side wall with the use of aluminum L-section of size 1\\"x1\\" (25x25mm) angles etc. Complete as per direction of Engineer-In-charge, manufacturer's specification & drawing. |
| 395 | Extra for providing edge moulding to 15-18mm thick marble/ Granite/Kota stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite/Kota Stone Work. Full Edge moulding |
| 396 | Providing & Laying Tactile tile (for vision impaired persons is standard of size 300x300x20mm and confirming to IS 1231 of 1980 (Re affirmed in 2006) in all colours & sheds further product should confirm ASTM 303 for shad resistance and DIN51099 for colour fastness etc. laid on 20mm thick base of cement mortar 1:4 (1 cement: 4 course sand) in all shapes & patterns including grouting the joint which white cement mixer) will matching pigments etc complete is per direction of Engineer-in-charges. Grade M 30 |
| 397 | Add extra for Fixing glazed/Ceramic/Vitrified floor tiles with cement based high polymer modified quick-set tile adhesive (Water based) conforming to IS: 15477, using 5kg. adhesive per sqm of tile area, in average 3mm thickness instead of cement mortar. |
| 398 | Supply & Installation of 2-Seater SofaSize: 1550mm(W) x 690mm(D)x 750mm (H) The top shall be of Upholstery with PU Finish. The sofas are made of solid wood base, reinforced with supportive addendum in the seat. Engineered wood panels form/support the overall design structure, they synergise with the solid wood to offer unparalleled life to the product. Foam padding of multidensity and varying thicknesses provide cushion for the sofa PU foam used is made Hennecke foam plants using German Technology capable of producing the high-quality flexible polyurethane foam. It provides unparalleled comfort, ease of use and durability. The foam used is 32 Density for seating areas and 28 Density for backrest. The supersoft foam used is in seating areas in 32-35 Density High-resilience (HR) foam which is unique and rarely used by manufacturers. Webbing: Interwoven high tensile elastic bands for optimum comfort and endurance, as approved by the Architect-in-Charge, |
| 399 | Providing and supplying Designer Centre Table suitable for As Sofa arrangement, overall size approx. 1400 mm x 800 mm x 450 mm height (oval/rectangular as approved), made of seasoned hardwood internal framework with 19 mm thick BWP grade plywood conforming to IS:710 including necessary stiffeners and supports, finished with approved natural veneer with high gloss/matt PU polish (minimum three coat system) on all exposed surfaces, top provided with 12 mm thick clear toughened glass with machine polished edges and corner rounding, supported on heavy duty designer MS base frame finished with powder coating (minimum 60 microns) / SS brushed finish / solid wood carved legs as approved, including all fittings, fixtures, screws, hardware, polishing, finishing, packing, transportation, loading, unloading and taxes etc. complete as per approved design and direction of Engineer-in-Charge. as approved by the Architect-in-Charge, |
| 400 | Supply & Installation of Chair Type 1 (Operator/visitor Chairs) Low back visitor model ABS for seat, Mesh back with extra lumber Support with fine tuning for depth adjustment, with fixed armrest, silver epoxy cantilever base Upholstery: Black Fabric Seat & mesh backrest All work shall be done as per specifications and satisfaction of authority including all transportation, loading, unloading, Tools-Hardware and fixing etc. |
| 401 | Providing and fixing factory made Brown Wooden Double Bed with box storage and designer cushioned headboard of size 1980 mm * 1830 mm ( ( 6' -6^ prime prime *6^ prime -0^ prime prime ) made of 19 mm thick BWP grade plywood conforming to IS:710 seasoned hardwood sections not less than 50mm * 75 mm, including full box type storage with 19 mm thick plywood bottom, 12 mm thick plywood mattress support with necessary stiffeners, headboard of 19 mm thick plywood base upholstered with 40 mm thick high density foam and covered with e approved quality fabric/leatherette, all exposed surfaces finished with 1.0 mm thick decorative laminate of approved shade and make, 2 mm thick PVC edge banding on exposed edges, heavy duty SS hinges/telescopic channels or hydraulic lift mechanism as required. including all fittings, fixtures, screws, hardware, polishing, carriage, loading, unloading, taxes, labour, tools and tackles etc. complete as per approved design and direction of Engineer-in-Charge. rooms |
| 402 | Providing and supplying 8 inch (200 mm) thick King Size Spring Mattress (Hotel Quality) of size 1980mm * 1830 mm ( 6' -6^ prime prime *6^ prime -0^ prime prime ) having high tensile bonnell/pocket spring core system made of minimum 2.4 mm thick spring wire, layered with PU foam of minimum 32 density on both sides with reinforced edge support system, finished with quilted knitted fabric top and anti-skid bottom layer, along with 4 Nos. soft fibre filled cushions/pillows of standard hotel size (minimum 700 grams filling each) complete with pillow covers, and one set of king size bed sheet with matching pillow covers made of minimum 300 thread count cotton fabric of approved shade and make, including packing, transportation, loading, unloading and all taxes etc. complete as per direction of Engineer-in-Charge. rooms |
| 403 | Providing and supplying Luxury Wooden Bedside Table with Storage, overall size approx. 500 mm * 450mm * 550 mm height (or as per approved drawing), made of seasoned hardwood internal framework with 19 mm thick BWP grade plywood conforming to IS:710 including necessary stiffeners, having minimum two drawers fitted with heavy duty soft-close telescopic channels (Hettich/Ebco or equivalent approved make), drawers provided with premium SS/brass finish designer handles, all exposed surfaces finished with approved natural veneer of selected species with high gloss PU polish (minimum three coat system including primer, sealer and final coat) of approved shade and make, top provided with 18-20 mm thick Italian marble / engineered stone/ solid wood top as approved, edges finished with designer moulding, complete with all fittings, fixtures, hardware, polishing, finishing, packing, transportation, loading, unloading and taxes etc. complete as per approved design and direction of Engineer-in-Charge. rooms |
| 404 | Providing and supplying heavy duty decorative metal banquet chair made of MS tubular frame (25-32 mm dia, 1.2-1.6 mm thick) with double circular back design as approved, including anti-rust treatment, primer and powder coated/metallic paint finish in approved shade, seat base of 12 mm thick BWR plywood with 50-75 mm thick high density foam cushion upholstered in approved quality fabric/ leatherette, including PVC/nylon bushes at legs, all welding, grinding, finishing, loading, transportation and placing at site complete in all respects as directed by the Engineer-in-Charge. Godrej/Featherlite / Durian/Zuari /Nilkamal (metal series) / or equivalent approved make. |
| 405 | Providing and supplying Designer Centre Table (Small Size) of approved pattern and design, overall size approx. 900 mm x 450 mm x 450 mm height (or as approved), made of 19 mm thick BWP grade plywood/MDF/hardwood frame as required, finished with 1.0 mm thick decorative laminate / natural veneer with melamine polish/PU polish of approved shade and make on all exposed surfaces, including designer profile edges, 2 mm thick PVC edge ce banding wherever required, top finished with 8-10 mm thick toughened glass/stone/solid wooden top as approved, supported on MS powder coated / SS brushed finish / solid wood designer legs or base frame, complete with all fittings, fixtures, screws, hardware, polishing, finishing, packing, transportation, loading, unloading and taxes etc. complete as per approved design and direction of Engineer-in-Charge. |
| 406 | Providing and supplying premium quality designer side cabinet/storage console made of 19 mm thick BWR/BWP marine grade plywood with high pressure laminate / veneer polish finish, including internal shelves, drawers with telescopic channels, soft closing hinges, stainless steel/brass designer handles, edge banding, back panel, polishing / PU finish, complete with all fittings, hardware, transportation and installation at site as per approved design and satisfaction of Engineer-in-Charge.Makes: Godrej Interio / Durian/Featherlite / Wipro Furniture / IKEA (premium series) /Urban Ladder or equivalent approved make. |
| 407 | Supplying, Installation, Testing & Commissioning of Electrical Driven fire fighting duty pump as per TAC and IS 12469-1988., Factory assembled in Pump make OEM for Sprinkler / Hydrant applications suitable for automatic operation and consisting of following details given as A, B, C, D, E, F, G and H. 1620 LPM suitable for 56 Mar Head End Suction Back pull type single Stage, 2900 RPM |
| 408 | Supplying Instutation Testing & Commission Diesel Engine Driven line fighing duty pump as per TAC and IS 12469-1988. Factory assembled in Pump make OEM rason and consisting of following details given as A. BCDEFG and H. for Sprider Hydrant spekciations sutante for automatic operation and consisting (A) End Suction Hornzentually st casing olure type Single Multi stage Contesfugal pump complete for celivery of belowmendoned discharge and Hand (8) Matenat of construction: Pump Casing-Castlech impellor Bronze Shaft-55 410, Packing Mechanical Seal (C)Pump shall be capable of furnishing not less than 150% of rated capacity at a head not less than 65% of the rared head. The shut off head shall nat exceed 120% of rared head (D) Heat Exchanger cocked Diesel Engine as per NFPA 20 developing suits BHP for the below mentioned discharge at 1500/1800 RPM flexible coupling and coupling guard with the Pump, common bed clase for mounting of the Engine and Pump Antivibration damping arrangement by cushy foot. Diesel Engine starting Paned for starting of the engine automatically if the Normal electrical supply lady with a unit of battery bank of 12:24. 180 An Lead Act Banery with Soost/Trickle charger as required for operation of Diesel engine. Exhaust Pipe of surable diameter upto 10 M length (with LRB insulation & Alum Cladding), win muller. Diesel tonk of 200 Lia capocity (made out from 2 mm thick MS sheet with King Cap) with drain cock, Diesel level Indicator, Suitable MS anglo ron stand for ploong tank, first Filling of Diesel ark (E) Desed Engine Control cumpriting Automatic/Manual sector switch & 3 anemets staring device immers and relays as required, push butions, sort stop in manual mods Indicating lamp for high Low Lub. Of pressure. High Water Temp and Engine on indication, Battery charger sulton for 12V/24V DC with boost and tickle selector swilch 0-30V DC valt meter and 6-20 ANC Atmeter, Al standard milays and accessones for automatic operasion of diesel engine System Controller in Exisang Fav Fighting Control panel (P) The Hydrostatic tests (2 times of design operssong head or 1.5 ames the shut off head whichever is higher) and performance tests to determine Developed head, Pump BHP and efficiency vis Flow) of pumps along with top lest shall be carned out at manufacturer's works in Physical presence of Department's representaves, (G) Phywal & Chemical Test reports of Pump casing Impeller () Shall (v) Shaft sleeve and Dynamic Balience cenficate is to be submined by DEM (H) Pump tu be placed on Sunar size Existing Renturced cement concrete (M-301 foundation with foundaoon bo, Nezing Angle of size 40mm x40mm x men (Cost ofRCC Foundation to be paid Extra All as per pre approved by Engineer in charge. For additional technical parameters of products work, refer Annexure \\"A\\" attached with this1620 LPM suitable fox 56 Mar Head End Suction Back pull type Single Stage, 1800/2300 RPM |
| 409 | upplying Institution, Testing & Commissioning of Electrical Driven fire fighting outy Jockey pump as per TAC and ES 12469-1958, Factory assembled in Pump make OEM suitable for automast operation and consisting of following details given as A, B, C, D. EF and Gspor TAC and IS 12480-1988, Factory assembled in Pump тана Supplying Intion. Testing & Commissiering of Electrical Driven fire fighäng duty Jockey pump as per OEM sutsole for automusic operation and consisting of following details given as A, C, D, EF and G180 LPM stable for 56 My Mu Stage |
| 410 | SITC of suitable Pressum release valve of 50 mm dia, of Ct body, with pressure setting range 7-15 1g/soom on discharge ncoder Ar Vessel complete in all respect exc as required. All as per pre approved by Engineer in charges. For addional technical parameters of products work refer Annexure \\"A\\" attached with the BSR |
| 411 | Providing & fixing pressure transc cacer in MS. Pipeline (рикласти гапди 6 10 m2) set 12 vol24 DC Induding connection etc, as requist (Comul Cable from Pressum Transducer to Panel to be Paid Extra), Alt as per pre approved by Engineer in charge. For additional technical parameters of products work, rafer Annexure \\"A\\" attached with tres BSR |
| 412 | Providing Fixing, Janang, Testing & Commissioning of Heavy duty MS C dass (Heavy) pipes conforming to R$ 3589/1239 pan-4 for hydrant and sprinkler applicanons damps Indương cuting, screwing, welding etc. & forged stock listings the albows, teds, tipers, roducer, gaskets etc. fing the pipe on the wallcoling with sulake nanger and nuts boks indading cutting nole and cruse in brik or RCC worlly stab and malong good the same, complete with panong of one cuats of Red Oude and twu or more coats of synthetic enamel paint of rogared shade complete as required. (Pipe ta be tested 10kg Soom for 2 Hrs. All as per pre approved try Engineerin dverige. For and lionat technical parameters of products worker Annexure \\"A\\" attached with this BSR80 MM DIA |
| 413 | 100 MM DIA |
| 414 | 150 MM DIA |
| 415 | Prosiding Futog Joling Testing & Commissiering of Heavy duty MS dans (Heavy) pipe conforming to 15:35551239 jan for ydrant and pre Existing trench with carment concrete block as supports induding cuaing, welding ent & torped editings ne elbows, wes, toers, reducer with during wrapping and costing of the pipe with a mm thick tar based polymaric commion protection sape including applying whiteem coast of cold pipelikol primer as per 15, 10221 for protection yons corrosion complete in all reiect, Pipe to telesed 10kgSom for 2 hrs & Excavation of Trench and refiling of wrench to be paid extra), All as per pr approved by Engineer in charge. For additional technical parameters of products/work, rater Annexure \\"A\\" atashed with this BSR 80 MM DIA |
| 416 | 100 MM DIA |
| 417 | 150 MM DIA |
| 418 | Supplying and firing cylindrical air vessel of concnuous welded construction for pump room made of 450 mm dia fabncased out of 10 mm thick dished ends and 8 mm thick MS sheet 2000 mim in height with flanged connection Provision for 25 mm dia dramvare acesse vote safety valve pressure gaugo as required accossones ond painting with two roots of Red Oride and two coat of post ofice red enamel painting the tankenstalled on suitably vertical legs. The keys shall be provided with M with M.S. Angle of size 75 mm x 75 mmthebotom, The legs shall be grouted in cement concrete foundicion, as required. (Ar Rekene vole, Drain valire, PRV. Pressure Gauge stull be Pard Extra). All is per pre approved by Engineer in charge. For addisonal cherical parameters of products/\\"A attached with the BSR |
| 419 | Supplying and Foring uf Pc 16 Plonged y serainor fabercated our of cast on body. 55 304 straner with portionated schoon with 3 mini dia holes in evang Mi / Gã pipe complete with 2 no. Matching Flanges (Minus 18mm thick nuts, bolts, washers, gaskets etc as reguntd of flowing wees. Ad as per pre approved by Engineerin charge. For additional technicall parameters of products work reher Anncture \\"A\\" attached with thes BSR150 MM DIA |
| 420 | Supplying and Frong of PN 1.6 Buterfly Valve (Water Type) with S. Gron Discand confirming to IS 13095 comgame with Ino, Matching Flanges (Minimum 16 mm thick), outs bolts, washers, paskers on as required of following sizes. Ad as per pre approved by Engineer in charge. For additonal technical parameters of products work, fer crure \\"A\\" attached with this BSR80 MM DIA |
| 421 | 100 MM DIA |
| 422 | 150 MM DIA |
| 423 | Supplying and Firing of PN 16 Brass/ GM Ball valves with scmwed end.55 Ball induding don Lipe escas required. All as per pre approved by Engineerin charge For actional sechnical parameters of products work reter Anncrurn \\"A\\" attached with this BSR 20 MM DIA |
| 424 | 25 MM DIA |
| 425 | 50 MM DIA |
| 426 | Supplying and furig of 55 304 Single/Double headed oblique patiem hydrant landing valve (item) with: 75/100 mm dia Bangod inlet & 63 mm doinsuantaneous type for cute coupling with cast iron whed complete win ABS cap and chan and all ac as per 15 5290 83 (Type-A) in dluding matching tonge (14 men thick), nuts bolts, washers, paskets refer Annexure \\"A\\" attached wit BSR pre approved by Engineer in charge, Fer anational technical parameters of products work,ngle Hooded win 75 mm Dia Flanged Inket |
| 427 | Supplying and firing wellice plato made of men mick Markess steel with antice of required sius in bedwson flange & bonding vare of restemol and anormal hydrant in reduce pressure to working pressum of 3.5 additional techrvical parameters of products 1.5 kgiom2 congêne with rubber gasket. Of bolis nus koshers, as required. All on per pre approved by Engineer in chargn. reler Arvocxame \\"A\\" attached with BSR. |
| 428 | Supplying and fung of Rebe 100% polyester block EPDM intermal rutiber Ining with External coat of synthetic elastomer 15.638 type) 63 πωι στο 15 intr. Long PIRL nove pipe with mutisteneous type 63 mm da 55-304 mike anit female cadres (15.003) dy turned and riveted to hoses pipes with cupper nwits and SS wire etc, as nequreit. Approprisle Test Certificate report with kable warranty of productiaccessones trom OEM what he submeles |
| 429 | Suppl The Branch shat have min Miah 03 s Fee Signang ros s pplying & tang 55-504 Short Branch Pipe conforming le 15. 003:93 fited with 20mm (nominal esiemal diameter) bove nozzle for propecting water in form of solid je approved by Engroser in charge. For additional technical powers of product work started we ws BSR |
| 430 | Supplying and long first-Aid Fun hose reel Dram wall moused swinging type with MG construction powder ported in post office Red cantarming to 3884-1900 win dals amendments, complete with the fullowing as required, (A) Thermoplastic/Rubber Hosa (8,20 mm da UL, FM Bronze Sa nozzle montico (Drum and brackets for fixing the equipments on wild (0) Conncuninstrom natr with 2025 mm da Brass/GM que rates with corewed conforming to 15.778 Class-1 enough Forged steel Screwed Union & M.S, pipe. Et as requred. All as per pre approved by Engineer in charge. For additional of parameters of pestucts worster Axure \\"A\\" attached wen Is BSRWith 30 x 20 min High Pressure Best Ruter Hose as per 15 5132-1980 anit Bursteng pisse 42 ку |
| 431 | Bursing and Lang Benching Carmection of Ct body with Gun Metal mats instantaneous indet couplings with Nev. Drainage Connecton with 50 nenass gato valve complete with PVC tank cap and can as required for 150mm dia Outlast with 1 no. Matching ete in regulired of following Ways. All as bar gee approved by Enanter in charge. For addan schnical parameters of products work refer Annexure Matching Flange (Mimum 10 mm thick, nuts, bolts, woshers, gaskets, with the BSR 2 Way |
| 432 | 4 Way |
| 433 | Providing and lang từ 100 mm Dia Flanged Gun Metal Fire brigade Suction hete coupling (draw cut connection) for female coupling as per IS 902-1974 complete with Matching Flange (Minimum 14mm Fok, nuts, boks washers, gasts, el as required. All as por pre approved by Engineer in charge, For additional technical parameters of products/for Annexure\\" attached with the BSR |
| 434 | forced rubber Nelle rubber cooted Bonducing Marching Supply and Feang of Cast on body une side Fibnged and other side saraner ball type foot valve with Flange (Mrinum 16 mm thick) nuts bus, washers gaskets els as regured of following Sizes. All us per pre approved by Engineer in charge. For additional technical porameters of products work, refer Annerare \\"Atached with the BSR 80 MM DIA |
| 435 | 100 MM DIA |
| 436 | 150 MM DIA |
| 437 | Providing and Fung of Pi Resent torked seglo and broton dimniators sutith forwwatorup to 45 dog. C temperature, working pressure 8.5 Figrem ant test pressure 14 Kigion provide does stitisses a pipe inducing Marthing Plarge 16m 3 ruts, bols, wathen, nkets, etc tokowing Sizes. Ad es per ore approved try Engineer in charge. Pero al parameters of products work der Annerure \\"A\\" attiched with ans BER inquired of 80 mm Dia 150 mm |
| 438 | 100 mm Dia 150 mm |
| 439 | 150 mm Dia 150 mm |
| 440 | Skying and Bang of 750x600mm 250mm Oudoor plate of 1.5 mm thick MG sheet Duty powder coated in red color extemally and white kemally with & mm thick goed doors with Expanded Memmick Jong necessity boking sangement suticle to accommodate 2 Nos 15 Mr. Long RRL Hose and 1 Ne, bronch pipe on Esting Wat Angle Iron Frame as required. (Cost of MS structure for mounting Frame be Pad Extra) All as per gre approved by Engineer in charge. For arms of products work for Annexure \\"A\\" artiched with this DGR |
| 441 | woplying and luing of 1000mm x 600mm x 500 mm Outdoor apolation Fire Hose Cabinet made of 1.6 mm thick MS sheet Duty powder coated in ned color externally no white rentally with 6k with Expanded Metal Jincluding neorssary leoung arrangement suticle to accommodate Extermal with butterfly vide 2 Nos 15 Athr. Long RL Hese antes branch pipe on Existing Wal Angle bon Frameset (Cost of MS wucture for mounting to be Pad Extral Af as per pre approved by Engnew in thirge. For additional technical parameters of product work refer Annexure \\"A\\" attached with this |
| 442 | Providing and Rung of Fire/Electro Shut Door made from powder (50 Morini unum pornsaty and with 6 mes this gloss and Panuly Fully Louvered with Oder ame of Aluna Seconf Sar 100m 45x1.5 mm and Shutter's Top Made & Section of See 8245x1.5mm Bortom Section of Size 110 mm x 45 mm x 1.5 mm Complete with hinges, Tower tot, Hande Aktio Locking Acarpetent indung dan fasteners of required da und size, necessary Ming the gaps at partuns Le at top bromom and sides with recured EPDM rubber seoprianie sket etc, as per drawings and the deections of Engineer-in-charge. Alles approved try Engineer in charge. For aduna technical p wens of products |
| 443 | Proveding & fixing of Usled 1.5 approved by Erginem in charge. For addonol parameters of products intor Acces кесте оf Бірmer piping with the bike coing. All as per pre siched with BSR |
| 444 | Succly & Fing of Fire Mars Ave with cation seeded & boor All as per see opproved by Engineer in charge. For adosenal trial prometers of products worker 115 326 with length appres 0.4 M & weight 3.0 Kg. е \\"А\\" nacht wen BSR |
| 445 | cortorening to 15 15222) atre 151 Marked as per 15 3224 Supply & Firing of Trolley outing 22.5 Kg 002 Fire Extinguisher conforming 15: 10012:2012, charged with CO2 gas purity 99.7 Powder coated Imemul & Exteet Surface Manganese stel marked as per 15 7285 cylinder body, Whert type Forged trass release valve 15 Marked as per Intrul safety reksised and Rup Disc Types, 1.5. Me long Moul wre beaded hose having meumum bursing presture of 140 Kg/cm2, Hom metalicizade Offer Pruduct Traceability, induding Double mounted handles migured of following capacity. Test Confticianes of all the Parameters along w Hycrorest & Burst For Body) Cristo OFMEADL Accredored Lan is to be sused. All us por pre approved by Enginoor in charge. For technical porameters of products work, reler Annexure \\"A\\" stached with vs BSR |
| 446 | Supply & Fixing of Orang Dry Peter Agent (er 15 4308 20150, Moc se presaze type AC Fire Extogusher, Powdeн сосед Рампа & Еметой Surface Doop drawn cylindo tody of Mar Steel CR2 grade conforming to 15 513 Fixed Bulb with Tomature så oog C. QR code for Product Tractabilly inctating Fang on Colling with stunts Archer Fasteners as red of lokowing capacity, Test Certificales of all the Parameters along with Hydro & Dust For Cylinder Body) Cerificans from CEME NAEL Acced Lan is to be similes. All as per pre approved by Engineer in charge. Foral pararners of procucts/ work Annexure \\"Ached with vs BCR Accredased5 Ka Capooty |
| 447 | uditorium AUDIOSupply of 15\\" Linear Coaxial Speaker with an AuraWave guide, Frequency Response (-3 dB) 46 Hz-20 kHz, Frequency Range (-10 dB) 41 Hz 20 kHz, Rated Power 500W Continuous, 2000W Peak, Maximunı SPL 136 dB, Sensitivity 99 d8, Nominal Impedance 8 Ohms, Coverage Pattern 60° x 60°, LF Driver 15\\" Coaxial Performance Driver, 3\\" VC-Ferrite, HF Driver 1.5\\" Ferrite HF Trandsucer, 2\\" VC, Crossover Frequency 1.9 kHz. Approved Make: British Acoustics/Martin Audio/L-Acoustics/D&B/MeyerSound |
| 448 | Supply of 2-Channel High Performance Amplifier Systems for Install Applications, Power at 4 Ohms (Stereo Mode, All channels driven) 1650W, Power at 8 Ohms (Stereo Mode, All channels driven) 900W, Bridged Power at 8 Ohms 3000W, Bridged Power at 4 Ohms 4000W, Dampning Factor> 400 at Bohms, Signal to Noise Ratio (1 kHz, 8 Ohms)-105 dB, THD < 0.02% THD/4ohms and 8 ohms, Controls Sensitivity Selection High Pass Cut Off Stereo, Bridge, Parallel Switch\\". Approved Makes: British Acoustics/Martin Audio/Powersoft/Lab Gruppen, |
| 449 | Supply of 18\\" Passive Subwoofer, Frequency Response (-3 dB) 38 H2-800 Hz, Frequency Range (-10 dB) 41 Hz-200 kHz, Rated Power 1000W Continuous, 4000W Peak, Maximum SPL 137 dB, Sensitivity 98 dB, Nominal Impedance 8 Ohms, Coverage Pattem Omni-directional, LF Driver 18\\" Ultra Long Excursion ADR Drivers, 4\\" VC- Ferrite, Inputs 2 x Speak-on Connectors, Wired Parallel. Approved Make: British Acoustics/Martin Audio/L-Acoustics/D&B/Meyersound. |
| 450 | Supply of 2-Channel High Performance Amplifier Systems for install Applications, Power at 4 Ohms (Stereo Mode, All channels driven) 2500W, Power at 8 Ohms (Stereo Mode, All channels driven) 1300W, Bridged Power at 8 Ohms 4100W, Bridged Power at 4 Ohms 6400W, Dampning Factor> 400 at 8ohms, Signal to Noise Ratio (1 kHz, 8 Ohms) |
| 451 | Supply of 8\\" Linear Coaxial Speaker, Frequency Response (-3 dB)-58 Hz-22kHz, Frequency Range (-10 dB) 53 Hz 22 kHz, Rated Power 300W Continuous, 1200W Peak, Maximum SPL-125 dB, Sensitivity-91 dB, Nominal Impedance-8 Ohms, Coverage Pattern-120 x 120\\", LF Driver-8 Coaxial Performance Driver, 2\\" VC-Ferrite, HF Driver 0.8\\" Dome Compression Drivers, 1 VC, Crossover Frequency-2.3 kHz. Approved Make: British Acoustics/Martin Audio/L-Acoustics/D&B/MeyerSound |
| 452 | Supply of 2-Channel High Performance Amplifier Systems for install Applications, Power at 4 Ohms (Stereo Mode, All channels driven) 850W, Power at 8 Ohms (Stereo Mode, All channels driven) 400W, Bridged Power at 8 Ohms 1600W, Bridged Power at 4 Ohms 2500W, Dampning Factor> 400 at 8ohms, Signal to Noise Ratio (1 kHz, 8 Ohms) 105 dB, THD < 0.02% THD/4ohms and 8 ohms, Controls Sensitivity Selection High Pass Cut Off Stereo, Bridge, Parallel Switch\\". |
| 453 | Supply of Powered 12\\" Linear Coaxial Speaker with an Ominiwave guide, Frequency Response (-3 dB) 49 Hz-20 kHz, Frequency Range (-10 dB) 44 Hz-20 kHz, Amplifier Power 500W Continuous, 1000W Peak, Maximum SPL 129 dB, Coverage Pattern 100 x 100\\", Controls Individual & Master Gain Knobis, Power Switch, LF Driver 12\\" Coaxial Performance Driver, 3\\" VC-Ferrite, HF Driver 1.3\\" Ferrite HF Trandsucer, 2\\" VC, AC Power Input Universal power supply 100-240 VAC, 50-60 Hz. Approved Make: British Acoustics/Martin Audio/L-Acoustics/D&B/Meversound |
| 454 | Supply of 2 Channel High Performance Amplifier Systems for install Applications, Power at 4 Ohms (Stereo Mode, All channels driven) 1650W, Power at 8 Ohms (Stereo Mode, All channels driven) 900W, Bridged Power at 8 Ohms 3000W, Bridged Power at 4 Ohms 4000W, Dampning Factor > 400 at Bonims, Signal to Noise Ratio (1 kHz, 8 Ohms)105 dB, THD 0.02% THD/4ohms and 8 ohms, Controls Sensitivity Selection High Pass Cut Off-Stereo, Bridge, Parallel Switch\\". Approved Makes: British Acoustics/Martin Audio/Powersoft/Leb Gruppen. |
| 455 | Supply of 12 inch Powered Speaker, Frequency Response (-3 dB) 60 Hz-20 kHz, Frequency Range (-10 dB) 51 Hz-20 kHz, Amplifier Power 850W Continuous, 1700W Peak, Maximum SPL 128 dB. Coverage Pattern 100 x 60\\", Controls individual & Master Gain Knobs, Power Switch, LF Driver 12\\" LF Driver, 2.5\\" VC-Ferrite, HF Driver 1.4 Titanium Compression Driver-1 VC, Connectors 2 x Balanced XLR Inputs 1 Balanced XLR Link Output Power input, AC Power Input Universal power supply 100-240 VAC, 50-60 Hz. Approved Make: British Acoustics/Martin Audio/TW Audio/Renkus Heinz. |
| 456 | Supply of 32 Frame Compact Analogue Mixing Desk with Dual FX, Number of input Channels 28 Mono 2 Stereo Channels, Media Player with USB/BT input, Number of Output Channels Master L-R XLR Output, Zone L+R XLR Output (Sub), USB Intefrace Out, Recording Out (2Track), TRS Aux, Monir, FX Mute & Headphone Outputs, Oliver FX Dual FX Engine, Recording 2-Track Recording in/Out, USB Audio Interface Connectivity, Auxes Balanced XLR Setero Aux Out, One TRS Aux Output, Frequency Responsе 20мг - 30KM: 0.5dB, Max. Input Level Mic-24dBu, Lire +24dBu, Other +20dBu, Max. Output Level XLR 26dBu, TRS 2000u, Max Input Power 40 Watts, Faders 60mm.Approved Make: British Acoustics/Soundcraft/Yamaha/Allen & Heath |
| 457 | Supply of of Dual Channel 31-Band Equalizer, 1/3 octave Constant Q frequency bands, Switchable boost/cut ranges of 16 or 112 dB, Front panel bypass switch, 12 dB input gain range, XLR and TRS inpts and Outputs, Frequency Response of <10Hz to 50kHz, Dynamic rangeof greater than 108dB Approved Make: DBX/DSL/DIGICO/Waves |
| 458 | Supply of High Precision Management System: 4-inputs, 8-cuputs with advanced correction filters & dynamic PEQ for Feedback Correction, Audio Input 4xBalanced XLR, Audio Output 8x Balanced XLR, Minimum Load 150 Ohms, THD+N 0.0001% at 1kHz, Sound to Noise Ratio 110dB, AD & DA Converters 24bit-96kHz, Parametric EQ 11 filters per input selected as Bell or Shelving, Centre Frequency Selectable with a 1/24th of octave resolution step from 20Hz upto 20kHz, Crossover Section HPF/LPF Butterworth 6/12/18/24 dB per octave. Approved Make: British Acoustics/OSL/ Biamp/Martin Audio |
| 459 | Supply of Wireless Handheld Receiver with Diversity Principle: True Diversity, No. of Channels: 2, Frequency response 20-20 Khz, Frequency Selection: Auto, Modulation: Wideband FM, Attenuation 0 to 14 Db selectable, LED Display, Range: 100 meters, With IIF Shielding and Wireless Handheld Microphone Transmitter with Microphone with Display on Transmitter, Type: Dynamic, RF Power Output: 30mW, Polar Pattern - Cardioid, Frequency response: 55 Hz to 20khz, Mute Button on Transmitter, Battery Operation time: B hour with rechargeable battery, Range: 100 meters, PLL Synthesized Circuits. Approved Make: OSL/Beyerdynamic/Shure/Sennheiser |
| 460 | Supply of Wireless Handheld Receiver with Diversity Principle: True Diversity, No, of Channels: 1, Frequency response 20-20 khz, Frequency Selection: Auto, Modulation Wideband FM, Attenuation: Oto 140b selectable, LED Display, Range 100 meters, With AF Shielding and Wireless Handheld Microphone Transmitter with Wireless Bodypack Transmitter with RF Power Output: 30mW, Frequency response. 20 Hz to 20khz, Volume & Mute Button on Transmitter, Battery Operation time: 8 hour with rechargeable battery, Range: 100 meters, PLL Synthesired Circuits. Approved Make: CSL/Beyerdynamic/Shure/Sennheiser |
| 461 | Supply of 18\\" Gooseneck Microphone with Electret Condenser, Polar Pattern: Supercardioid, Freq. Response: 20-17 kHz, Max SPL: 140 dB, Working Volatge: 48V DC Phantom Power And Gooseneck. Base with Switch, Frequency Response 20-20,000 Hz, Power Requirement Phantom power 48V or bastery power 1.5V2 (ST-5030k work with 12-48V Phantom power), Current Consumption-Stand-by 2.4mA, Current Consumption-Operating 6.6mA, Switches Microphone selection ECM MIC unbalanced input, ECM MIC balanced input Dynamic MIC input Magnetic switch: power on/off, Aprraved Make: DPA/OSL/Neumann/Sennheiser |
| 462 | Supply of High-performance Handheld Vocal Microphone (cardiold, dynamic) with metal housing & adapted sensitivity for deep vocals. Includes (1) Travel Case (2) Placement Rings & (2) Wind Protectors.. Aprroved Make: DPA/OSL/Neumann/Sennheiser |
| 463 | Supply of Instrument microphone (supercardiold, hybrid condenser) for drum overheads with 3-pin XLR-M. Includes (1) Mic clip and (1) travel pouch. Aprroved Make: DPA/OSL/ Neumann/Sennheiser |
| 464 | Supply of Mic Stand BigAprroved Make: MyStand/DPA/OSL/Neumann/Sennhelser/Custom |
| 465 | Supply of 2.5sqmm 2 core speaker cable Approved Make: Krystal/Belden/Sommer/LYNQ |
| 466 | Supply of 2 core Signal/Microphone cable Approved Make: Krystal/Belden/Sommer/LYNQ |
| 467 | Supply of 24 pair 33 mtr Snake cable with patch box Approved Make: huja/Hawk/Krystal/LYNQ |
| 468 | Supply of Interconnects Approved Make: Nutrik/Amphenol/reputed make |
| 469 | Supply of 16U Audio rackApproved Make: Valrack/Comrack/Netrack/Reputed Make |
| 470 | contengencey 3% part A + Part B Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 31, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 13, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 10 daysAug 14, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 11 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender