Tender For Improvement To Toilets In Bldg No Pm-90 And Certain Swts At Afs Bidar
Tender Value
19 Lakhs
Estimated cost
Bid Submission
21 Aug 2026
14 days left
EMD
38000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Bidar → Karnataka
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Improvement To Toilets In Bldg No Pm-90 And Certain Swts At Afs Bidar
BOQ
| Sl. No. | Item Description |
| 1 | SCHEDULE OF WORKS |
| 2 | Taking down cement plaster on brick or stone walls etc. including racking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed. |
| 3 | Demolition of un-reinforced cement concrete of any description and in any position not otherwise specifically provided for, including removing debris outside MD land complete all as specified and as directed. |
| 4 | Demolition of Brick work or PCC solid block masonry built in cement mortar or cement lime mortar including all quoins, arches, pillars etc. but excluding ashlar facings dressed stone work and pre-cast concrete articles, including removing debris outside MD land complete all as specified and as directed. |
| 5 | Material and labour, for Pre-cast cement concrete block masonry with grade ‘C’ solid blocks exceeding 10 cm in width, having minimum compressive strength of 40 Kg / Sq cm as per IS 2185 (Part- I) 2005 and set in CM 1:6 complete all as specified and as directed. |
| 6 | Material and labour for Plain cement concrete 100 mm thick 1:3:6 type C2 (20mm graded stone aggregate) as in sub base complete all as specified and directed. |
| 7 | Material and labour for providing plain cement concrete 1:2:4 type B0, using 12.5 mm graded stone aggregate as in bed blocks/coping etc. including necessary form work all as specified. |
| 8 | Material and labour for rendering 15mm thick on fair faces of brick work/concrete surfaces in cement mortar 1:3 complete all as specified and as directed. |
| 9 | Removing all loose particles, sharp projections from sunken slab, Preparing surfaces and providing Material and labour for two-component, UV resistant, acrylic polymer modified cementitious coating system, in 2 layers using Shalicem EWP 150 of make STP limited having two component (pack of 50 Kg mix of proportion 34 Kg powder mixed with 16 Kg liquid) @ 2.5 Kg / Sq m in each layer to achieve 1.5 mm thickness complete all as per manufacturers instructions and as directed by Engineer-in-Charge. |
| 10 | Material and Labour for Preparing of New plastered surface of Wall, Chajja, Roof Projection and Roof Fascia surface and applying acrylic smooth exterior paint of approved shade by mechanical sprayer (2 or more coats applying @ 1.67 litre / 10 sq m over and including priming two coats of Acrylic Smooth exterior paint of required shade over a coat of exterior primer applied @ 2.2 Kg / 10 Sq m complete all as per manufacturer instructions and as directed by Engineer-in-Charge. |
| 11 | Dismantling unframed structural work, railing, grills, doors, gates, etc. complete all as specified and as directed. |
| 12 | Material and labour for mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete using steel section conforming to Fe.290.Gde-E-165 complete all as specified and as directed. |
| 13 | Material and labour for mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed. |
| 14 | Material and Labour for Preparation of New steel surfaces of any description, over 10cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of zinc chrome primer complete all as specified and as directed. |
| 15 | Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in hard / dense soil complete all as specified and as directed by Engineer-in-Charge. |
| 16 | Material & Labour Hardcore of Broken stone or boulders gauge not exc.63 mm , deposited, spread and levelled in layer not exc. 15 cm thick, watered and rammed to a true surface complete all as specified and as directed. |
| 17 | Material & Labour 75 mm thick plain cement concrete Type D-2, 1:4:8 (40 mm graded stone aggregate) as in sub base for floor complete all as specified and as directed. |
| 18 | Material & Labour 75 mm thick plain cement concrete Type B1, 1:2:4 (20 mm graded stone aggregate) as in sub base for floor complete all as specified and as directed. |
| 19 | Material and labour for rendering 15mm thick on fair faces of brick work/concrete surfaces in cement mortar 1:4, and finishing surfaces even and smooth without using extra cement complete all as specified and as directed. |
| 20 | Material & Labour for Preparing of new plastered surface of concrete wall and applying two coats of distemper oil bound over a coat of chalk whitening, complete all as specified and as directed. |
| 21 | Taking down chowkats or frames exc 1.5 sqm but not exc 4sqm each but with shutters (without taking off shutters from the frame), complete all as specified and as directed. |
| 22 | Dismantling, wall and ceiling boards (fibre, pulp, insulation, etc.) orinsulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and as directed. |
| 23 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed. |
| 24 | Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for, including removing debris outside MD land complete all as specified and as directed. |
| 25 | Material and labour for Plain cement concrete 25 mm thick 1:2:4 type B0 (12.5 mm graded stone aggregate) as in sub base for laying tiles, complete all as specified and directed. |
| 26 | Material and labour for 35 mm thick factory made flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides and one face is covered with decorative face veneer with lipping/frame to match complete all as specified and as directed. |
| 27 | Material and labour anti skid coloured ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc. set with spacer, joints of more than 3mm are grouted with epoxy grout and pointed in white or coloured cement to match the tiles including 15 mm thick screed bed in CM 1:6, complete all as specified and directed. |
| 28 | Supply and fixing of Glazed ceramic coloured tiles in vertical surface 450x 300x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the tiles as in skirting/dado including matching PVC corner beading over and including provision of backing coat of 10 mm thick in CM 1:4.etc, complete all as specified and directed. |
| 29 | Material and labour for, 18- 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms including edge moulding, machine polish to edge as required and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite all as specified and as directed. |
| 30 | Supply and fixing of Solid PVC Door Frame of size 50mm x 47mm made out of 5mm both side pre laminated of any colour PVC sheet reinforced with M.S. Square tube, supplying & fixing in opening as per specification & drawing, complete all as specified and directed. |
| 31 | Supply and fixing of Factory made solid panel PVC door both side pre laminated shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded both side pre laminated of any colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Paneling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing, complete all as specified and directed. |
| 32 | Material and Labour for 18/19mm thick Plywood, grade BWP type BB fixed with screws to timber frame complete all as specified and as directed. |
| 33 | Supply and fixing for 1mm thick laminated mica glossy finishes in any colour, fixed with adhesive material for shutters of ward robes, cabinets, wall paneling etc. complete all as specified and as directed. |
| 34 | Supply and Fixing for steel slip-on soft closing concealed hinges with nickel plated for high corrosion resistance of dimensions 110x60x30mm and weight 150 gm for kitchen cabinet, ward robes etc. complete all as specified and as directed. (Make: Godrej Product or Techno commercial equivalent of approved makes specified here-in-after) |
| 35 | Supply and Fixing stainless steel floor door stopper finished with brass antique of 125 mm over all length with cover plate and tongue with hard drawn steel spring fixed in floor, Complete all as specified and as directed. |
| 36 | Supply and fixed in repairs mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate including fixing with necessary fittings in doors, complete all as specified and as directed. |
| 37 | Supply and Fixing of Soap dispenser with pump action complete all as specified and as directed.Make: Parryware CAT No. T6513A1 or Techno commercial equivalent of approved makes specified here-in-after |
| 38 | Supply and fix in repairs brass chromium plated shower rose 150mm size with or without swivel joints any size including fixing to steel pipe of 15mm bore complete all as specified and as directed. (Make: Parryware CAT No. T5135A1 or Techno commercial equivalent of approved makes specified here-in-after) |
| 39 | Supply and Fixing of 5mm thick glass corner glass self of 300mm radius with CP brass railing fixed with brass Brackets complete all as specified and directed.(Make: Parryware CAT No. T6010A1 or Techno commercial equivalent of approved makes specified here-in-after) |
| 40 | Supply and Fixing of Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 500cm long and 125cm wide with chromium plated bracket guard and railing complete all as specified and as directed.Make: Parryware CAT No. T6009A1 or Techno commercial equivalent of approved makes specified here-in-after |
| 41 | Supply and fixing of Butt Hinges extruded aluminium alloy with galvanized mild steel hinge pin, anodized 100 mm long complete all as specified. |
| 42 | Supply and fixing of Aluminum anodized barrel tower bolts of extruded section 150mm long complete all as specified and as directed. |
| 43 | Supply and fixing of Aluminum anodized bow handle fabricated type extruded section of 150mm long complete all as directed |
| 44 | Supply and Fixing for 125mm long stainless steel door handle finished with brass antique fix with brass screws complete all as specified and as directed. |
| 45 | Supply and fixing of 300mm aluminium alloy, anodized, sliding door bolts with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, complete all as specified and as directed. |
| 46 | Supply and fix in repairs stainless steel 25mm dia Curtain rods (wall thickness not less than 1.2 mm) with supports etc., complete all as specified and as directed. |
| 47 | Supply and fix in repairs 25mm dia chromium plated fancy type decorated approved design brackets with end sockets to hold the curtain rod properly complete all as specified and as directed. |
| 48 | Supply and fix in repairs brass peg set of six with screws complete all as specified and direct.(Make: Parryware or Techno commercial equivalent of approved makes specified here-in-after) |
| 49 | Material and labour for Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 on brick work, ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth, complete all as specified and as directed. |
| 50 | Taking down steel tubing 15mm bore and connections, including cleaning for refixing all as specified and directed. |
| 51 | Supply and fixing of GI tubes medium grade with all fittings and fixed complete to walls and ceiling or laid in floors, 15mm dia bore all as specified and directed |
| 52 | Taking down steel tubing 20mm bore and connections, including cleaning for refixing all as specified and directed. |
| 53 | Supply and fixing of GI tubes medium grade with all fittings and fixed complete to walls and ceiling or laid in floors, 20mm dia bore all as specified and directed. |
| 54 | Taking down steel tubing 25mm bore and connections, including cleaning for refixing all as specified and directed. |
| 55 | Supply and fixing in GI tubes medium grade with all fittings and fixed complete to walls and ceiling or laid in floors, 25mm dia bore all as specified and directed. |
| 56 | Supply and fix in repairs Wash basin oval shape counter top of size 555x450x205mm in any coloured including 32mm bore CP Waste coupling and PVC connection pipe of 15mm x 450mm long complete all as specified and as directed. (Make : Parryware CAT No C0407 or Techno commercial equivalent of approved makes specified here-in-after) |
| 57 | Supply and fix in repairs vitreous China urinal, half stall type with and including waste coupling CP of 40 mm dia PVC flexible waste pipe including all accessories, complete all as specified and as directed. |
| 58 | Supply and fixing of chromium plated Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms), complete all as specified and as directed. |
| 59 | Supply & Fixing in PVC waste pipe 32mm bore for WHB/Sink/Urinal, complete all as specified and as directed. |
| 60 | Supply and fixing in beveled edge mirror 600x450mm of selected quality glass mounted on 6mm commercial plywood and fixed to wooden plug with chromium plated screws and caps all as specified and directed |
| 61 | Supply and fix in repairs vitreous China wash down water closet (Pedestal Pattern) white (excluding flushing cistern and flush pipe) including PVC seat cover white closed pattern with recessed bottom and connection to drain or out going pipe and flushing pipe, complete all as specified and as directed. (Size and Cat Part No _____) |
| 62 | Supply and fix in repairs vitreous China wash down water closet Vitreous China, semi-pedestal pattern (Anglo-Indian Type) white (excluding flushing cistern and flush pipe) including PVC seat cover white closed pattern with recessed bottom and connection to drain or out going pipe and flushing pipe, complete all as specified and as directed.(Make: Parryware CAT No. C0126CS or Techno commercial equivalent of approved makes specified here-in-after) |
| 63 | Supply and fix in repairs 10 litre capacity PVC Low level flushing cistern including 32mm dia PVC flush pipe, fixing in position with PVC connection pipe of 15mm x 450mm long etc., complete all as specified and as directed. (Make: Parryware CAT No. E8333 or Techno commercial equivalent of approved makes specified here-in-after) |
| 64 | Supply and fix in repairs 15mm bore chromium plated cast copper alloy bib taps fancy type with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule all as directed.(Make: Parryware CAT No. G0204A1 or Techno commercial equivalent of approved makes specified here-in-after) |
| 65 | Supply and fix in repairs 15mm bore stop valves/angle cock, chromium plated fancy type, screwed down high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions all as directed. (Make: Parryware CAT No. G0253A1 or Techno commercial equivalent of approved makes specified here-in-after) |
| 66 | Supply and fix in repairs 15mm bore CP 2- Way bib cock double handle with wall flanges, glossy finish complete all as specified and as directed. (Make : Parryware CAT No G021ZA1 or Techno commercial equivalent of approved makes specified here-in-after) |
| 67 | S&F in repairs 15mm bore Brass CP mixer for mixing hot & Cold water screwed down for iron pipe complete all as directed. |
| 68 | S&F in repairs brass chromium plated shower rose 125mm size with or without swivel joints any size including fixing to steel pipe of 15mm bore all as directed. |
| 69 | Supply and Fixing of 15mm bore Brass CP mixer(3 in 1) with wall flange ( provision for over head shower and hand shower) for mixing hot & Cold water screwed down for iron pipe complete all as directed. (Make : Parryware CAT No G022FA1 or Techno commercial equivalent of approved makes specified here-in-after.) |
| 70 | Supply and Fixing of 15mm bore ABS hand shower Mult flow 100mm with 1.5M SS tube & ABS Hook complete all as specified and as directed. Make : Parryware CAT No G022FA1 or Techno commercial equivalent of approved makes specified here-in-after. |
| 71 | Supply and fix in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. |
| 72 | Supply and fix in repairs 15mm bore chromium plated cast copper alloy wall mounted sink cock screwed for iron pipe or for brass ferrule complete all as specified and as directed. (Make: Parryware CAT No. G4721A1 or Techno commercial equivalent of approved makes specified here-in-after) |
| 73 | Supply and fix in repairs Tubular towel rail 20mm dia D type 60cm long between flanges chromium plated all as specified and directed. (Make: Parryware CAT No. T5901A1 or Techno commercial equivalent of approved makes specified here-in-after) |
| 74 | Supply and fix in repairs Brass Towel ring Complete all as specified and directed. (Make: Parryware CAT No. T5902A1 or Techno commercial equivalent of approved makes specified here-in-after) |
| 75 | Supply and fix in repairs SS grating 100mm dia complete all as specified and as directed. (Make: Parryware or Techno commercial equivalent of approved makes specified here-in-after) |
| 76 | Supply and fix in repairs Toilet paper Holder with Cover of chromium plated complete all as specified and as directed. (Make: Parryware CAT No. T5914A1 or Techno commercial equivalent of approved makes specified here-in-after). |
| 77 | Supply and fix in repairs PVC (SWR) floor trap 75mm dia plain with grating including jointing with solvent cement etc, complete all as specified and as directed. |
| 78 | Supply and fix in repairs 110mm dia PVC (SWR) pipes, type 'B', single socketed in any length with rubber joints fixed to walls etc., complete all as specified and as directed. |
| 79 | Supply and fix in repairs 75mm dia PVC (SWR) pipes, type 'B' single socketed in any length with rubber joints fixed to walls etc., complete all as specified and as directed. |
| 80 | Supply and fix in repairs PVC (SWR) bends 110mm dia any radius with access door, complete all as specified and as directed. |
| 81 | Supply and fix in repairs PVC (SWR) bends 75 mm dia any radius with access door, complete all as specified and as directed. |
| 82 | Supply and fix in repairs PVC (SWR) junction single,(Single T) 75mm dia equal or unequal with access door, complete all as specified and as directed. |
| 83 | Material & Labour for Rendering 10 mm thick plaster on internal wall surfaces in CM (1:6) finishing the surface even and smooth without using extra cement all as specified and directed . |
| 84 | Material and labour for Preparation of New plastered surface of wall and applying two coats of oil bound distemper over one coat of alkali resistant primer, complete all as specified and as directed. |
| 85 | Material & Labour for Applying 2mm thick wall care putty on wall at any height etc., complete all as specified and as directed. |
| 86 | Complete removal of existing treatment of ceilings and providing Material and labour for applying two coats of oil bound distemper over one coat of alkali resistant priming paint, complete all as specified and as directed. |
| 87 | Material & Labour for Rendering 5mm thick on fair faces of concrete surface of ceiling in CM 1:3, surface finished even and smooth surface without using extra cement complete all as specified and as directed. |
| 88 | Material and labour for Preparation of new plastered surface on ceiling in height and any description and applying two coat of oil bound distemper over a alkali resistant priming coat, complete all as specified and as directed. |
| 89 | Use and waste of formwork (flat concreted surface) to soffits of suspended slabs as in in roof slab, landing, deck slab and similar work not exceeding 20mm thick complete all as specified and directed |
| 90 | Material and labour for reinforced cement concrete 1:2:4 type B-0 using 12,5mm graded stone aggregate, as in shelves, hajjes, water troughs, shelves and similar articles etc., complete all as specified and directed.Note: Reinforcement steel will be measured and paid separately. |
| 91 | Material and labour for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking bending spirally for handle, rungs and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, as in cover slabs, complete all as specified and as directed. |
| 92 | Material & Labour for PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in sunken floor, filling and mass concrete complete all as specified and as directed. Cement concrete in foundations, filling and mass concrete |
| 93 | Material & Labour for plastering 10mm thick CM 1:4 with WPC on sunken floors, roof slabs, Water Retaining Structures concrete surfaces complete all as specified and as directed.Note: Supply only WPC shall be measured and paid separately. |
| 94 | Supply only Liquid based water proofing compound. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 31, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 21, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 14 daysAug 28, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 21 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender