Tender For Providing Of Toilet Block In Mes Officers Mess( Mes) And Addn& Altn To Bldg No P-146 Vsn Chiloda .
Tender Value
46 Lakhs
Estimated cost
Bid Submission
20 Aug 2026
8 days left
EMD
92000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Gandhinagar → Gujarat
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Providing Of Toilet Block In Mes Officers Mess( Mes) And Addn& Altn To Bldg No P-146 Vsn Chiloda .
BOQ
| Sl. No. | Item Description |
| 1 | Excavation in trenches n.exc 1.5m and n.exc 1.5m in depth for foundation etc n.exc 10 Sqm on plan and n.exc 1.50m in depth and getting out in any type of soil complete all as specified and directed. |
| 2 | M & L for cement concrete in fioundation filling and mass concrete type D2 1:4:8 (40mm graded aggregate) complete all as specified and directed |
| 3 | All as per Item no 2 above but exc 1.5 m and upto 3.0m depth.complete all as specified and directed |
| 4 | M&L Brick work with fly ash brick, old size bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed |
| 5 | Returning, filling in including spreading, watering & well ramming in layers n exc 25 cm thick complete all as specified and directed. |
| 6 | Removing excavated material exc 250 M but n.exc 500 m and depositing where directed at a level n.exc 1.50 m above the starting point. |
| 7 | M&L for reinforced cement concrete Design Mix M-25 using 20mm graded stone aggregate as in Foundation, plinth beam etc complete all as specified and directed. |
| 8 | M&L for reinforced cement concrete Design Mix M-25 as in roof beams, cantilevers, breassummers and lintels over 1.5m span complete all as specified and directed. |
| 9 | M&L for RCC Design mix M-25 as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like,complete all as specified and directed. |
| 10 | M&L for reinforced cement concrete Design Mix M-25 using 20mm graded stone aggregate as in Column, pillar piers, Post & struts etc complete all as specified and directed. |
| 11 | M&L 18-20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite in floors etc, set , jointed pointed with grey cement slurry mixed with pigments to match the shade of the slabs including rubbing & polishing laid over and including 15 mm thick screed bed in CM 1: 6 ,complete all as specified and directed. |
| 12 | M&L for steel formwork to sides of pillars, posts, struts, piers, columns and stanchions in square, rectangular or polygonal rough finished surfaces of concrete complete all as specfied and as directed. |
| 13 | M&L for Formwork for flat rough finished surfaces to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified & directed. |
| 14 | M&L for form work to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed. |
| 15 | M&L for form work to soffits of suspended slabs such as roof slabs etc of concrete surface complete all as specified and directed. |
| 16 | Use and waste of form work to edges of concrete flats, roofs, floors etc and sides of RCC/PCC bands in walls, horizontal or sloping, and similar work exc 10cm but not exc 20cm wide for rough finished surface complete all as specified and directed. |
| 17 | M&L TMT bar 10mm dia and over cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including MS wire (annealed) than 0.90mm dia complete all as specified and directed. |
| 18 | M&L TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spaces and binders, cut to length bent to shape required, including crancking bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire not less than 0.9 mm dia or securing with clip quality complete all as specified. |
| 19 | M&L for 5mm thick cement rendering to RCC surfaces in CM 1:3 on ceiling finished even and smooth (without using extra lime or cement) complete all as specified and directed. |
| 20 | M & L Rendering 15mm thick in CM 1:6 on brick or concrete surfaces including finihsed the surface smooth and even without using extra cement ,complete all as specified and directed. |
| 21 | 15 mm thick rendering on fair faces of brick work or concrete surfaces of walls etc 10 mm thick im CM 1:6 and 5 mm thick in CM 1:4 incl water proofing compound as per manufacturers instruction & finished the surfaces even and smooth without using extra cement, complete all as specified and directed. Note : WPC WILL BE MEASURED AND PAID SEPERATELY |
| 22 | Supply only integral water proofing compound. complete all as specified and directed. |
| 23 | Preparation of new surfaces of walls by applying Wall care white ( Putty) thickness not less than 3 mm and sand papering surfaces to achieve smooth surfaces and applying two coats of plastic emulsion paint of approved shade and pattern complete all as specified. |
| 24 | Preparation of new plaster surfaces of ceiling and applying two coats of plastic emulsion paint complete all as specified and directed. |
| 25 | M&L for applying Two coats of 100% Premium acrylic emulsion paint havingVOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10sqm over new surfaces ,complete all as specified and directed. |
| 26 | M&L preparation of newly plastered surfaces of ceilings by applying Wall care white ( Putty) thickness not less than 2mm and sand papering surfaces to achieve smooth surfaces and applying applying two coat of distemper oil emulsion all as specified and directed. |
| 27 | Surface excavation n.exc 30cm deep and averaging 15cm deep and getting out in any type of soil complete all as specified and directed. |
| 28 | M&L Non skid coloured ceramic tiles of any shade and any pattern of size 600 x 600 x 10 mm thick, as in floors etc over and including 15mm thick screed bed in CM 1:6 as in floors etc. jointed in neat cement slurry and pointed in colored cement to match coloured tiles..(The Colour, shade and pattern shall be approved by the GE during execution work). |
| 29 | All as per item no 28 but Colored glazed ceramic tiles in vertical surfaces 600x300x7mm / 450 x 350 x 7 mm thick set over 10mm thick backing coat in CM 1:4 and jointed in neat cement slurry and pointed in white or colored cement to match ,complete all as specified and directed. |
| 30 | M & L for Brickwork with flyash bricks, straight or curved on plan to any radius in half brick thick walls, built in CM 1:6 complete all as specified and directed. |
| 31 | M&L 15 mm thick Glazed Vitrified Tile in steps, jambs, pillars, window cills, cooking platform, WHB platform in any position including screed bed 15 mm thick in cement mortar (1:4) and pointing with white or coloured cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed. Note:- Single piece for WHB table top. |
| 32 | S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplying & fixing in opening as per specification & drawing. |
| 33 | S&F Factory Made Solid PVC Moulded Door Shutter wooden, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick 3D wood grain Moulded PVC Sheet Polyurethane painted on the front face & 2mm Prelam colour PVC Sheet on back face supplying & fixing in frame at site as per specification & drawing complete all as specified and as directed. |
| 34 | S&F 15 mm bore pillar taps cast copper alloy with capstan heads fancy type chromium plated screwed down high pressure with long screwed shanks and fly nuts screwed for iron pipes complete all as specified and directed. |
| 35 | S&F 20 mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 incl Tee,elbow and coupler with all fittings and fixed to walls and ceiling or laid in floors, complete all as specified and directed. |
| 36 | S&F 25 mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 incl Tee,elbow and coupler with all fittings and fixed to walls and ceiling or laid in floors, complete all as specified and directed. |
| 37 | S&F 18mm thick PVC Sheet one side prelaminated of approved texture (Celuca Ply of Rajashree Make or equivalent in sintex as approved by GE) as in cabinet with shelves and partitions) including required beading and necessary fitting and fixtures such as 02 Nos SS auto close concealed hinges of size 75mm and 01 No SS handle of size 75mm in each shutter as per manufacturers instruction complete as in repairs all as specified and directed |
| 38 | S & F vitreous china 520mm x 360mm X 390mm snow white wash down water closet pan (pedestal pattern ) s type (excluding fixing bolts, flushing cistern )with flush pipe and seat cover complete all as specified Make :- CERA S1057101 and seat cover B1510121 , or Equivalent make as approved by GE |
| 39 | S&F for twin flush flushing cistern, low level, snow white, with inlet, ball calve, float and handle including brackets, flush pipe and fittingsMake- CERA B1020106 or Equivalent make as approved by GE |
| 40 | S&F 5.5 mm thick looking mirror glass with selected quality of any size including fixing with SS studs and similar etc complete all as specified and as directed |
| 41 | S&F long body bib cock with wall flange complete all as specified and directed. (Make : Jaquar Cat part No COP-107PM or Equivalent make as approved by GE) |
| 42 | S&F angular stop cock with wall flange complete all as specified and directed. (Make : Jaquar Cat part No COP-057PM or Equivalent make as approved by GE) |
| 43 | S&F towel ring square with round flange complete all as specified and directed. (Make : Jaquar Cat part No ACN-1121N or Equivalent) |
| 44 | S&F soap dispensor with metallic bottle complete all as specified and directed.(Make : Jaquar Cat part No ACN-1137N or Equivalent make as approved by GE) |
| 45 | S&F toilet paper roll holder with stainless steel flap with wall flange complete all as specified and directed. (Make : Jaquar Cat part No ACN-1153S or Equivalent make as approved by GE) |
| 46 | S&F Hand shower (Health Faucet) brass chromium plated with 8 mm Dia 1.2 meter long flexible tube and wall hook(back flow preventor) complete all as specified and as directed. (Make :-Jaquar Cat part No ALD-577 or equivalent make as approved by GE ) |
| 47 | S&F stainless steel grating Square 150 x 150mm with waste hole (Minimum weight 100gms) complete all as specified and directed. |
| 48 | S&F brass chromium plated bottle traps for wash basins and urinal with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified and directed (Make : Jaquar ALD-769L300X190 or Equivalent make as approved by GE) |
| 49 | S&F 15 mm size Two way bib tap with wall flange complete all as specified Make : Jaquar OPP-GDS-15041PM or Equivalent make as approved by GE |
| 50 | S&F Vitreous China urinals including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including brass screws, pointing around urinal back in cement including fitting such as spreader and outlet discharge pipe, coupling all as specified and directed.Make- Jaquar URS-WHT-13255 or Equivalent make as approved by GE |
| 51 | S&F Urinal spreader of chromium plated of any colour for fixing with 15mm dia pipe complete as in repairs all as specified and as directed ( Make :- Cera Cat No. F8070201 or Equivalent make as approved by GE in writing ) |
| 52 | S&F vitreous china white thin rim table wash hand basin 550 mm x 400 mm x 140mm including all necessary fitting such as CP waste coupling 32mm dia ,bottle trap and other misc fitting complete all as specified and as directed.Make :- CERA S2020137 or Equivalent make as approved by GE |
| 53 | S&F Curved shaped urinal partition with frosted glass 10 mm chrome finish of size 900x450 mm and including fixing with SS brackets including taking down exist partition complete as in repairs all as specified and as directed..(Make: Jaquar Cat No JSE-CHR-110UC450X or Equivalent make as approved by GE ) |
| 54 | S & F aluminium powder coated ) min thickness of powder coating 50 micron of approved colour) ventilator , partially glazed and partially louvers , outer frame and mullion fafricated with aluminium section of size 82.50mm x 38mm x 1.70mm thick (Cat No. 20036 Jindal or equivalent) half portion glazed with 4mm thick froasted glass including rubber bedding and glazing clip half portion louveres of 80mm wide and 4mm thick frosted glass including aluminium louver patti including SS wire gaze for fixing of 0.36mm dia and 1.40 width aperturer with 25x3 mm thick aluminium strip with screw to upper half portion of ventilitor all fitting & fixture and fixed in position. |
| 55 | S&F in repairs 40mm PVC (SWR) pipes single socketed in any length with rubber ring joints, laid to wall |
| 56 | S&F in repairs PVC connections 15mm size with PTMT nuts of length 450mm |
| 57 | S&F 1000 Ltrs capacity rotational moulded polythene water storage tank (cylindrical vertical with closed top) hoisted and fixed on roof in position including all fitting such as connection pipe pieces with GI tank nipple for inlet, outlet, wash out and overflow etc and incl Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/20mm-210 gms/25mm-455gms / 40mm- 690 gms) complete all as specified in SSR Part I complete all as specified and directed. |
| 58 | S&F 75mm dia of outlet PVC (SWR) floor trap with grating including jointing with solvent cement.complete all as specified and directed. |
| 59 | S&F 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints, laid to wall ,complete all as specified and directed. |
| 60 | S&F 75mm PVC (SWR) junction single, (single T) ,complete all as specified and directed. |
| 61 | S&F 75mm PVC (SWR) bends any radius ,complete all as specified and directed. |
| 62 | S&F 75mm PVC (SWR) vent cowl ,complete all as specified and directed. |
| 63 | M&L PVC (SWR) gully trap 125/110mm, setting and jointed with solvent cement,complete all as specified and directed. |
| 64 | S&F 110 mm PVC (SWR) pipes single socketed in any length with rubber ring joints, laid to wall ,complete all as specified and directed. |
| 65 | S&F110 mm PVC (SWR) junction single, (single T)complete all as specified and directed. |
| 66 | S&F 110 mm PVC (SWR) bends any radius ,complete all as specified and directed. |
| 67 | S&F 110mm PVC (SWR) vent cowl ,complete all as specified and directed. |
| 68 | S&F in 100mm long butt hinges, medium weight, cast brass,with mild steel hinge pin, bright polished and fixed, type B-11 complete all as specified and as directed.,complete all as specified and directed. |
| 69 | S&F in 200mm extruded brass handles, fabricated type polished complete all as specified and as directed. |
| 70 | S&F in 200mm extruded brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts and fixed complete all as specified and as directed. |
| 71 | M&L for Hard core of guage n.exc 63mm of broken stones, deposited, spread and levelled in layer n.exc 15cm thick water and rammed to a true surface. |
| 72 | M&L for PCC type D2 1:4:8 (40mm graded aggregate) 75 mm thick as in sub base complete all as specified complete all as specified and directed. |
| 73 | M&L for 75 mm thick, plain cement concrete 1:3:6, type C-2 (using 40mm graded crushed stone aggregate) as in plinth protection etc, finishing surface even and smooth without using extra cement including making joints with bitumastic filling in proportion of bitumen and sand 1:3 by weight complete as specified and directed.(Note : The concrete shall be laid at a stretch n.exc 3.0 m in length and every turning/ corners. |
| 74 | Preparation of concrete surfaces of accessible roof by scrubbing down with steel brushes and cleaning with water all loose dirt/dust and applying following treatment(a) Applying 1st course of 15mm thick screed bed with cement mortar 1:4 over concrete surface. (b) Applying 2nd course of bitumen primer conforming to IS-3384 @ 0.4 Kg/Sqm over screed . (c) Applying 3rd course of a coat of bonding material with blown type bitumen of grade 85/25 heating to a working temperature of 180 C and applied @ 1.2 kg per Sqm.(d) Applying 4th course of APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified (e) Applying 5th course of a coat of bonding material with blown type bitumen of grade 85/25 heating to a working temperature of 180 C and applied @ 1.2 kg per Sqm. |
| 75 | S&F 20mm gate valves, with iron wheel head, screwed both ends for iron pipe and fixed ,complete all as specified and directed. |
| 76 | M&L for cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting not exc 10 cm girth complete all as specified and directed |
| 77 | M&L Concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested; in cement concrete M-10(Nominal mix )using 20mm graded aggregates for 150mm dia bore pipes all as per SSR PART I complete all as specified and directed. |
| 78 | M&L Sail-glazed stoneware (SGSW) grade A drain pipes150mm bore laid and jointed in concrete bed complete including testing etc all as specified and directed as per SSR PART I specifications ,complete all as specified and directed. |
| 79 | M&L Precast cement concrete 1:2:4, type B1 (Using 20 mm graded stone aggregate) in landings, cover slabs (for manholes etc.) shelves and similar articles with plain faces and set in cement mortar 1:4 including necessary form work ,complete all as specified and directed. |
| 80 | PCC 1:2:4, nominal mix, type B-0, using 12.5mm graded crushed stone aggregate as in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, coping, bed plates and the like including weathering, slightly rounded or chamfered angles and throating including necessary form work, complete all as specified. |
| 81 | M&L Rendering 15 mm thick in cement mortar 1: 4 on fair faces of brick work or concrete surfaces, finished even and smooth with out using extra cement, complete all as specified. |
| 82 | M&L Plain cement concrete 1:2:4, type B-1 (using 20mm graded stone aggregate) as in benching, water troughs and the like including form work and finishing all exposed surfaces of concrete, complete all as specified directed. |
| 83 | M&L for Chequered cement concrete tiles 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors using grey cement and pigments laid over 15mm thick screed bed in CM 1:4 screed bed or bedding layer complete all as specified and directed. |
| 84 | Dismantling of stone slabs & tiles of any thickness & in any position laid, bedded and pointed in any mortar otherwise specified. |
| 85 | Demolition of RCC (reinforcement cut as required to facilitate demolition) roofs, floors (other than ground floors), beams, staircases, landing,chajjas, parapet, lintel beam etc and similar suspended work complete all as specified and directed. |
| 86 | M&L Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed |
| 87 | Taking down chowkhats or frames with shutters (without taking off shutters from the frames) of size exc 1.5 sqm but n exc 4.00 sqm each complete all as specified and directed. |
| 88 | Taking down chowkats or frame with shutters(without taking off shutters from the frame not exceeding 1.50 sqm & removing to store all as specified and directed by Engineer - in-Charge. |
| 89 | Dismantlling of Plain or corrugated steel sheeting, asbestos cement sheet, fibre glass reinforced translucent any gauge, thickness, including Nainital or similar pattern roof covering complete all as specified. |
| 90 | Taking down cement plaster of any description including racking out joints, hacking for key and disposing of debris out side MOD Land complete all as specified and directed. |
| 91 | M&L of PCC 1:2:4, nominal mix, type B-0, using 12.5mm graded crushed stone aggregate as in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, coping, bed plates and the like including weathering, slightly rounded or chamfered angles and throating including necessary form work, complete all as specified. |
| 92 | M&L for preparation of new plastered surfaces of wall and applying putty 2 mm thick or more as required to level the wall surface and two coats of oil bound distemper over a coat of chalk whiting on plastered surfaces complete all as specified and as directed. |
| 93 | M&L for ATT Along the internal and external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes minimum 300mm depth @ 300mm c/c etc in apron complete all as specified and as directed. |
| 94 | M&L for Vitrified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM (1:6) complete all as specified and as directed. |
| 95 | All as per item 94 but on vertical surfaces/skirting/Wall and including backing coat of 10mm thick in CM (1:4) including tile adhesive Make:- (Kajaria or Equivalent) |
| 96 | M&L for double charged Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 SQM not exceeding 3.00 SQM, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match premium quality as in floor etc and including screed bed 20mm thick in CM (1:6) with including tile adhesive or all as specified and directed.Make:- (Kajaria or Equivalent) |
| 97 | All as per item 96 above but on vertical surfaces/skirting/Wall and including backing coat of 10mm thick in CM (1:4) including tile adhesive Make:- (Kajaria or Equivalent) |
| 98 | S & F 12mm thick toughened sliding glass door with door sensor unit including any section (SS) as required at site for installing sliding toughened glass of any size & description including necessary accessories for door approved by GE / EIC complete all as specified and directed. |
| 99 | Demolition of Brickwork built in cement morter including work all quoins, aches, pillars, etc, complete all as specified and directed. |
| 100 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. |
| 101 | S & F 12mm thick toughned glass of any size & description (As approved by GE) including necessary accessories like SS studds etc to fix vertically approved by GE / EIC complete all as specified and directed. |
| 102 | S & F frosted film of 50 micron to glass panes exc 1.5 sqm as per instructions of manufacturer complete all as specified. |
| 103 | M&L for RCC (Nominal Mix) Type B1 (1:1.5:3) (20mm graded aggregate) Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under reamed piles and mass concrete etc complete all as specified. |
| 104 | M&L 18-20mm thick Lakha red granite work (table rubbed and polished including moulding, polishing) as in floor etc in any position including 15mm thick screed bed in cement mortar (1:4) and pointing with white or coloured cement (1:2) using marble dust with admixture of pigment to match with shade of granite of existing floors complete all as specified and directed. |
| 105 | M&L for Formwork to flat rough finished surfaces sides and soffits of floor or roof beams, beam haunchings , girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and directed. |
| 106 | M&L for RCC 1:2:4, nominal mix, type B-0, using 12.5mm graded crushed stone aggregate as in cantilevers, bressummers, lintels over 1.5m span etc complete all as specified and directed. |
| 107 | Taking up or down CPVC/steel tubing pipe and connections 15mm bore complete all as specified and directed. |
| 108 | Taking up or down CPVC/steel tubing pipe and connections 20 mm bore complete all as specified and directed. |
| 109 | S&F in repair single piece WC with UF soft close seat cover, hinges, dual flush, cistern fittings, fixing accessories and accessories set of size 360mm x730mm x 740mm, with 'S' trap 300mm complete all as specified and directed. (Make : Jaquar Cat part No SLS-WHT-6851S300UF or Equivalent make as approved by GE) |
| 110 | S&F Rimless Back to Wall WC with UF soft close slim seat cover, hinges ,fixing accessories and accessories set of size 370mmx580mmx430mm with 'P' trap 180 mm complete all as specified and as directed. (Make :-Jaquarr Cat part No-OPS-WHT-15955P180UFSM or Equivalent make as approved by GE ) |
| 111 | S&F Control Plate Alive complete all as specified and as directed. (Make :-Jaquar Cat part No JCP-CHR-852415 or Equivalent make as approved by GE ) |
| 112 | S&F Single piece slim Concealed cistern with floor mounting frame ,installation kit and ''P- Type \\" Drain Pipe connection set for wall hung WC complete all as specified and as directed. (Make :-Jaquar Cat part No JCS-WHT-2400FP or Equivalent make as approved ) |
| 113 | S&F Round shape thin rim table top basin with fixing accessories of size 480mm x480mm x135 mm including Click Clack Waste coupling full thread 130 mm height all necessary fitting complete as in repairs all as specified (Make :-Jaguar Cat part No OPS-WHT-15901N,ALD-727L130 or Equivalent make as approved by GE) |
| 114 | S&F4-6 mm thick wall mounted LED illuminated mirror of high quality moisture resistant and polished edges. The mirror shall be provided with built in energy efficient LED strip lighting cool light, warm light and neutral white as specified with uniform diffused illumination complete all as specified and as directed |
| 115 | S&F shinny Shower panel of size 1600x230mm incl all necessary fitting complete as in repairs all as specified (Make :-Jaguar Cat part No JPL SSF-ST8896 Chrome or Equivalent make as approved by GE) |
| 116 | S&F Pillar Cock with 450 mm long braided hoses complete all as specified and directed.(Make :-Jaguar CAT No: KUP-35001PM or Equivalent make as approved by GE) |
| 117 | S&F in repair long body bib cock with wall flange complete all as specified and directed. (Make : Jaquar Cat part No COP-107PM or Equivalent make as approved by GE) |
| 118 | S&F in repair angular stop cock with wall flange complete all as specified and directed. (Make : Jaquar Cat part No COP-057PM or Equivalent make as approved by GE) |
| 119 | S&F in repair towel ring square with round flange complete all as specified and directed. (Make : Jaquar Cat part No ACN-1121N or Equivalent make as approved by GE) |
| 120 | S&F in repair soap dispensor with metallic bottle complete all as specified and directed.(Make : Jaquar Cat part No ACN-1137N or Equivalent make as approved by GE) |
| 121 | S&F in repair toilet paper roll holder with stainless steel flap with wall flange complete all as specified and directed. (Make : Jaquar Cat part No ACN-1153S or Equivalent make as approved by GE) |
| 122 | S&F in repair stainless steel grating Square 150 x 150mm with waste hole (Minimum weight 100gms) complete all as specified and directed. |
| 123 | S&F in repairs 15 mm size Two way bib tap with wall flange complete all as specified Make : Jaquar OPP-GDS-15041PM ,complete all as specified and directed. |
| 124 | S&F remote control operated blackout roller blinds of size as per required width & drop, having hardware top tube made of extruded aluminium with 38mm dia and wall thickness of 1.2mm with spline adoptable to accommodate clutch of UNISILIL/ACMEDA make CLUTCH MECHANISM moulded plastic having self-lubrication with glass fibre reinforcement having a minimum lifting capacity head adoptability 38mm operating chain plastic/steel ball chain adoptable to the clutch pitch for smooth operation of blinds locking member plastic /steel stop locks for limit setting adoptable to be steel chain bonding 30/36mm wide double sided adhesive tape of 3M for strong holding capacity SPRING BOOSTERS provided as per the requirement bottom bar aluminium extruded circular section with powder coated finish , having a min. weight to be 365gms /Rm for a perfect fall to fabric to avoid warpage /floating ends are covered with ends cap to give a perfect finish FABRIC – blackout roller blinds WINFAB MAKE composition PVC/FIBREGLASS weight 470gms/sq mtr etc complete all as specified and as directed. Indoor Air Quality – Green Guard/ ECO-Codices Certified. (Make: Marvel /D’Decor /Hunter Douglas or equivalent. etc complete sample / design approved as per GE including taking down old vertical blind complete all as specified and directed by Engr in Charge |
| 125 | M&L for Non-skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 Sqm but not exc 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including screed bed 15mm thick in CM (1:6) complete all as specified and directed. |
| 126 | M&L for aluminium powder coating (powder coated of required colour) three track sliding windows frame top and sides of size 92x31.75x1.5mm (section No 20831), bottom size 92x31.7x1.5mm (section No 20832) and shutter top & bottom of size 40x18x1.55mm (section No 20736) and sides (handle) of size 40x18x1.55mm (section No 20738) and lock side shutter frame of size 40x18x1.45mm (section No 20737) with rubber gasket beading and locking arrangement and rollers etc including making good to the disturbed portion complete including stainless steel wire mesh 0.36mm nominal dia of wire with 1.40mm average aperature and fixed with stainless steel wire staples and fixing 5mm thick glass (plain/tinted/with laminated film)with necessary rubber beading gasket etc complete all as specified and as directed. |
| 127 | M&L aluminium powder coated (minimum thickness of powder coating 50 micron) sections suitable for doors frame , window and ventilator complete all as specified and directed. |
| 128 | S&F in 5.5 mm thick toughened glass, incl all fitting for fixing as in partition, fixed in horizontal or vertical surfaces and the edges of the glass should be properly moulded / grinded all as specified and directed. |
| 129 | S&F powder coated, any colour, aluminum door shutters (minimum thickness of powder coating 50 micron), aluminium section weighing 0.55 Kg/ Sqm including necessary jointing cleats, glazing clips, rubber neoprene packing, tower bolts, handles in each door, hinges, anodised aluminium snap beading, screws etc. complete all as specified and directed. |
| 130 | M&L Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet fixing on 5mm thick PVC sheet fillet of width 35mm inclusive of solvent cement fixing at site for wall panelling as per specifications and drawing complete |
| 131 | Dismantling of cast iron, PVC or reinforced concrete pipes jointed in cement mortar and taking out of trenches or on wallls upto 110 mm in dia, complete all as specified and directed. |
| 132 | M&L for 10 mm thick rendering in CM 1:6 on concrete surfaces / fair faces of brick masonary wall, finished even and smooth without using extra cement complete all as specified and directed. |
| 133 | M&L for 15 mm thick rendering in CM 1:4 on concrete surfaces / fair faces of brick masonary wall including mixed with water proofing compound @ 3% by weight of cement, finished even and smooth without using extra cement complete all as specified and directed. |
| 134 | M & L 10mm thick rendering in Cement Mortar 1:3 on fair faces of brick work or concrete surfaces of ceiling finished even and smooth without using extra cement complete all as specified and directed . |
| 135 | S&F Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and directed . |
| 136 | S&F plain framed, Panelled shutter (two Panel) with lock rail and panel of 9mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated ,complete all as specified and directed . |
| 137 | S & F flush shutter 30mm thick solid core construction with block board core and plywood face panels commercial type & both sides covered with decorative face veneer with lipping / frame to match all as specified and directed . |
| 138 | Hacking out old broken glass of any thickness, size, quality or description from metal /wooden frame including punching or drilling out old glazing pins/spring clips etc complete all as specified and directed. |
| 139 | M&L for preparation of old painted surfaces of wall and applying one coat of plastic emulsion paint using roller brush complete all as specified and as directed by Engr-in-Charge. |
| 140 | Material and labour for providing kitchen cabinet and cubboard in required sizes at site made out of 18mm thick PVC sheet (prelam) having one side decorative laminated sheet (for shutter, sides of cabinet, partition and shelves etc). All the edges of shutter and front exposed edge of partition/shelves shall be covered with 2mm thick edge bonding tape as per manufacturer. Including all required fixing material such as SS brackets, screws, adhesive etc., including taking out old any type cabinet complete all as specified and as directed by Engineer-in-charge.Note :- (i) The area of each sheet (shutter, sides of cabinet, partition and shelves) shall be measured in sqm for payment.(ii) Magnetic catcher, handles, continuous Piano hinges and PVC frame (where required) shall be measured and paid separately under appropriate item of BOQ.(iii) Any other material required for making/fixing/hanging of cabinet shall deemed to be included in the quoted unit rate nothing extra shall be paid on this account. |
| 141 | S & F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed. |
| 142 | S & F pre painted galvalume aluminum Zinc coating GI based plain steel sheeting 0.5mm thick of any colour having tensile strength of 550 MPA as in ridge ,gutters etc fixed with self tapping screws as specified. |
| 143 | S&F Stone / Marble glossy finish for Aluminium composite panel (ACP) sheet 4 mm thick size (max 3600mm x 1200mm x4mm) of selected quality cladding with silicon and 3M tape, fixed to wooden, concrete, brick, angle frame including aluminium grid frame of size 25x50x2mm thick horizontal and vertical frame c/c 450 mm in wall/ ceiling/column surfaces with necessary cleaning of surface and making surface even and smooth including scaffolding complete all as specified and as directed. Note:- ACP panel fix with T-Joint measured and paid separately. |
| 144 | S & F for position suspended PVC /WPC Louvers false ceiling using premium grade 8mm/9mm thick multicolours panels of approved colour, shade and design. The panels are fixed onto a rigid, concealed framework. Framework shall consist of rigid structure using 25mmx25mm GI section or specialized aluminium T-section/runners suspended from the roof slab/beams using 8mm dia GI threaded rods, rawl plugs and heavy duty angle cleats & as per manufacturers instructions.Note : No extra payment for multi level steps, vertical drops (cove drops) and pattress work for cove lighting as per the architect design and drawing. |
| 145 | M&Lof 12mm thick plaster of paris ceiling (Gypsum anhydrous) to flat surface over GI Grid frame work incl any sunk or raised moulding including Gl frame work for seam less ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre incl Hangers 6 mm dia. G.I. (upto1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified |
| 146 | Providing and fixing factory made uPVC white colour fixed window in any area reqd at site made of extruded profiles with wall thickness of 2.3mm(+-0.2mm). Window profile with hollow section with multi chamber. Frame (60mm x 58mm). T profile (Onevertical length in between twoshutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc. making arrangement for fixing of hardware, EPDM gasket. 1.2 +–0.2mm thick, galvanized steel Frame (28mm x 21.5mm), T profile (27mm x 17 mrn) to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners- 5mm thick glazing with selected quality glass (Note: The unit rate quoted by contractor includes cost of tinted/frosted/clear toughened glass of thicknes 8mm/ and includes all other connected accessories Net opening will be measured for payment purpose.) |
| 147 | M & L for Steel work as in tubular trusses as in post including special shaped washer and etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete all as specified & directed. |
| 148 | S&F mild steel purpose made bolts of diameter of neck exc 12 mm but n.exc 20 mm with hexagonal or square head one end and screwed the other or screwed both ends, each screwed ends to be fitted with washers and one hexagonal or square nut exc 30 cm long complete all as specified. |
| 149 | S&F plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachement conforming to Fe 410 W (Grade E-250 ,quality 'A' ) |
| 150 | S&F for rolled mild steel in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. and similar small articles conforming to Fe 410 W (Grade E-250 ,quality 'A' ) complete all as specified and as directed. |
| 151 | M&L for applying two coats of synthetic enamelled paint over a coat of red oxide on steel or iron surface based materials of any description , not other wise described over 10 cm width or girth including preparation of new surfaces. |
| 152 | M&L for Preparaing surfaces of wood and wood based materials, and priming with pink primer and applying two coat of synthetic enamel paint, complete all as specified and as directed Please Enable Macros to View BoQ information |
| 153 | M&L for Preparaing surfaces of wood and wood based materials, and priming with pink primer and applying two coat of synthetic enamel paint, complete all as specified and as directed Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 30, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 20, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 8 daysAug 22, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 10 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender