Tender For special Repair To Md Accn Bldg No J-99 At Robert Line Under Age B/R I And Age E/M (S) Of Ge (S) Secunderabad
Tender Value
48.05 Lakhs
Estimated cost
Bid Submission
19 Aug 2026
1 days left
EMD
96200
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Hyderabad → Telangana
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repair To Md Accn Bldg No J-99 At Robert Line Under Age B/R I And Age E/M (S) Of Ge (S) Secunderabad
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and as directed. |
| 2 | Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, complete all as specified and as directed. |
| 3 | M&L for PCC (1:4:8) type D2 using 40mm graded stone aggregate as in foundation filling, post concerete and mass concrete complete all as specified and as directed. |
| 4 | S&F of Structural Steel work as in columns, posts, stanchions etc using ERW or induction butt welded tubes conforming to IS-1161-1998 grade St.-240 or with holow structural steel sections conforming to IS 4923-1997 Grade St-240 complete all as specified and as directed. |
| 5 | M & L for rolled mild steel in plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as specified and as directed. |
| 6 | M&L for aluminium composite panel sheet of 3.0mm thick, for MS post and gap filling on sides with skin thickness of 0.25mm of aluminium on both sides, sandwiched by 2.5mm polyethylene core with PVDF coating of 30.0micron fixed over frame of aluminium tabular section 50x25mmx 2.0mm thick, with necessary silicon filling, in approved pattern as in column, beam, wall etc. complete as specified and as directed. |
| 7 | Dismantling timber scantling 40 sq cm and over in any position complete all as specified and as directed. |
| 8 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed. |
| 9 | S & F of structural steel work in tubular trusses including special shaped washer etc.. using ERW or induction butt welded tubes conforming to IS-1161-1998 grade St.-240 or with holow structural steel sections conforming to IS 4923-1997 Grade St-240 complete all as specified and as directed. |
| 10 | S & F of structural steel work as in main and cross beams, hip and jack rafters, purlins where connected to common rafters , vertical posts, etc fixed with angle cleats or other connecting plates, cleats etc. using ERW or induction butt welded tubes conforming to IS-1161-1998 grade St.-240 or with holow structural steel sections conforming to IS 4923-1997 Grade St-240 complete all as specified and as directed. |
| 11 | S&F for compound girders and stanchions, lattice girders, aerial masts, staging for water tanks and the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates, etc.Fe-410-W Grade E-250 Quality A complete all as specified and as directed. |
| 12 | M & L for cutting chases in PCC block walls for placing the steel etc., and making good, cutting not exc 10 cm girth complete all as specified and as directed. |
| 13 | Dismantling of Asbestos cement (corrugated, semicorrugated and Transulent sheet etc) sheets in roof covering incl ridges complete all as specified and as directed. |
| 14 | Dismantling of Mangalore pattern roofing tiles with or without ceiling tiles or slate roofing in roof covering incl ridges complete all as specified and as directed. |
| 15 | S&F pre painted galvalume aluminium zinc coating GI based corrugated (manglore pattern or any other design as per required.) steel sheet 0.5mm thick of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall with self tapping screws complete all as specified and as directed. |
| 16 | S&F pre painted galvalume aluminium zinc coating GI based plain or design pattern as required steel sheet 0.5mm thick of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall with self tapping screws complete all as specified and as directed. |
| 17 | M&L for preparation of new steel surfaces and applying two coat of synthetic enamel paint over a coat of red oxide zinc chrome primer on Surfaces of any description,over 10cm in width or girth, not otherwise described complete all as specified and as directed. |
| 18 | Dismantling of wall and ceiling boards (fibre pulp insulation etc) or insulation boards / slabs /blankets any thickness, including cover fillets complete all as specified and as directed. |
| 19 | M & L for seamless false ceiling made out of 12mm thick of gypsum board fixed to the ceiling section with 25mm long self drilling and tapping screws having Philips head with under head cutter at 200mm centre to centre, including finishing the joints of face board with specially formulated joining compound and 48 mm wide fibre tape to provide seam less finish and including GI channel 0.55 mm thick with two unequal flanges of 20 to 30mm and web of 27 mm fixed to surrounding wall using nylon sleeve and screws at 450mm centre to centre/intermediate channel 0.9mm thick having two equal flanges of 215 mm each and web of 45 mm suspended from soffits at approx. 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.20mtr length) of 0.55 mm thick having kurled web of 50 mm and flanges of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre including 6mm thick GI hangers adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flats 40x3 mm size long and expansion hold fasteners 12.5mm dia 40mm long including thin layer of Pop with Gypsum binder, sanding the surfaces till smooth surface is obtained and finally applying two coats of acrylic emulsion over one coat primer over 3mm thick putty complete all as specified and as directed |
| 20 | Dismantling floor, hearth or wall tiling including cement mortar bedding but not backing removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed. |
| 21 | Dismantling stone slab or tiles of any description or thickness laid in any mortar as in floors, aprons etc complete all as specified and as directed |
| 22 | M & L for PCC 1:2:4 type B0 (using 12.5mm graded stone aggregate) 25mm thick as in levelling course, sub-floors and paving etc complete all as specified and as directed. |
| 23 | M & L for Cement concrete type B- 2, 1:2:4 (40mm graded aggregate) 75 mm thick as in levelling course, sub-floors and paving etc complete all as specified and as directed. |
| 24 | M & L for vitrified tiles light shade 10mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exc. 1.0 sqm as in floors etc. set and jointed in neat cement slurry and pointed in white/ coloured cement, laid over and including cement screed bed 15 mm thick in cement mortar 1:6, complete all as specified and as directed. |
| 25 | All as per item No 24 above but as in skirting / dados etc. including backing coat 10mm thick in cement mortar 1:3, complete all as specified and as directed. |
| 26 | M&L for non skid ceramic coloured tiles 7 to 8 mm thick (Square / rectangular) area of each tiles exc 0.06 Sqm but n. exc 0.11 Sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match including 15mm thick screed bed of CM (1:4) complete all as specified and as directed. |
| 27 | M&L for heavy duty non skid coloured tiles 8 to 10 mm thick area of each tile exceeding 0.18 sqm but not exc 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM 1:6 and complete all as specified and as directed. |
| 28 | All as per item No 27 above, but as in skirting / dados etc. including backing coat 10mm thick in cement mortar 1:3, complete all as specified and as directed. |
| 29 | M&L for glazed ceramic tiles in vertical surface 450X 350X 7 to 8 mm/600x300x7 to 8mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm thick rendering in CM 1:4 and complete all as specified and as directed. |
| 30 | M&L for formwork to chullah hoods, chajjas, troughs and similar items including edges kitchen plateform etc of rough finished flat surfaces concrete complete all as specified and as directed |
| 31 | M&L for reinforcement cement concrete type B0 (1:2:4) 12.5mm graded stone aggregate as in slabs supported on walls, beams and columns in floors roofs, landings, balconies canopies, deck slabs and in shelves, kitchen shelfetc complete all as specified and as directed. |
| 32 | M&L 16 to 18mm thick granite stone (of any type ) work (table rubbed and polished) in floors, staircase tread & risers of steps, cooking platform, window cill/jambs etc laid bedded over 15mm thick CM (1:4) bedding & pointed in white/coloured cement to match coloured tiles including Rounding, grinding and mirror polishing complete all as specified and as directed. (Note : Colour of granite shall be as approved by Engr-In-Charge) |
| 33 | Demolition of precast cement concrete block walling built in CM or Cement lime Mortar complete all as specified and as directed. |
| 34 | M&L precast cement concrete block masonry exc. 10 cm width with solid block C1 (1:3:6) (using 20 mm graded stone aggregate) and setting in cement mortar (1:6) complete all as specified and as directed. |
| 35 | M&L precast cement concrete solid building blocks or slabs Type C1 1:3:6 (20 mm graded stone aggregate) 10cm thick (with plain or interlocking joints as directed) setting in mortar(1:4), complete, in walls complete all as specified and as directed. |
| 36 | M & L for cement concrete 1:3:6 type C-1, 75 mm thick using 20mm graded stone aggregates as in plinth protection finished fair and even with using extra cement complete all as specified and as directed. |
| 37 | Taking down cement plaster and raking out joints, hacking for key,scrubbing down with water built in cement mortar any description complete all as specified and as directed. |
| 38 | M & L for rendering 15mm thick in CM 1:4 on fair faces of brick/concrete finished even and smooth without using extra cement, complete all as specified and as directed. |
| 39 | M&L for rendering in two layer i.e.5 mm thick in CM 1:4 including with or without mixing water proofing compound over 10mm thick in CM (1:6) on concrete/block masonry surfaces and finished even and smooth without using extra cement complete all as specified and as directed.(Note WPC shall be measured and paid separately in relevent item) |
| 40 | M&L for preparation of newly plastered wall surfaces with 3mm average thick wall care putty and applying two coat of oil bound distemper over one coat of primer including leveling the surface which undulation found with cement putty etc complete all as specified and directed. |
| 41 | M&L for preparation on newly plastered external wall surface and applying two coat of weather proof (exterior grade) acrylic emulsion paint with anti fungal property over a coat of primer of the same manufacturer as that of paint complete all as specified and as directed. |
| 42 | M&L for complete removal of existing treatment on wall by scrapping, washing, cleaning etc with 3mm average thick wall care putty and applying two coat of acrylic emulsion distemper over one coat primer including filling of cracks, holes and including leveling the surface which undulation found with wall care putty etc. complete all as specified and as directed. |
| 43 | M&L for complete removal of existing treatment of old decorated external wall surface by scrapping, washing, cleaning etc and applying two coat of weather proof (exterior grade) acrylic emulsion paint with anti fungal property over a coat of primer of the same manufacturer as that of paint incl filling cracks, holes using wall care putty complete all as specified and as directed. |
| 44 | Taking down frames with shutters (without taking off shutters from the frame ) area not exc 1.5 Sqm Each incl iron mangery complete all as specified and as directed. |
| 45 | Taking down frames with shutters (without taking off shutters from the frame) area exc 1.5 Sqm but n.exc 4 Sqm Each incl iron mangery complete all as specified and as directed. |
| 46 | S & F of stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with galvanised wire staples. compete all as specified as directed. |
| 47 | Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory indows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extrapayment on this account shall be made. |
| 48 | Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately) complete all as specified and as directed. |
| 49 | M & L for pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete , of frame size 125 x 60 mm, including one shop coat of red oxide zinc chrome primer complete all as specified and as directed. |
| 50 | M & L for pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete , of frame size 105 x 60 mm, including one shop coat of red oxide zinc chrome primer complete all as specified and as directed. |
| 51 | M&L for providing cement concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregates for filling in the pressed steel door frame/hold fast complete all as specified and as directed. |
| 52 | M&L for Mild Steel flat iron as in hold fast supplied and fixed including tarring complete all as specified and as directed. |
| 53 | M&L PCC 1:2:4 type B1 using 20 mm graded stone aggregate as in Coping, gap filling in between roof sheet and wall etc similar work complete all as specified and as directed. |
| 54 | M&L for 30 mm thick flush door shutters solid core construction with block board core and both face covered with decorative face venner with lipping/frame to match complete all as specified and as directed. |
| 55 | S & F of 2nd class hardwood 35mm thick glazed and skeleton shutters, and both face covered with decorative face venner with lipping/frame to match open rebated and prepared to receive glass gauze etc divided into squares, with plain, chamfered or rounded mitred and rebated sash bars any number edges of framing plain, chamfered or rounded, fitted with cut and metered beads for securing glass etc size of members of shutters as specified in SSR Part I Sec 8 clause 8.24 (a), fitted to chowkhats complete all as specified and as directed. |
| 56 | Providing and fixing factory made UPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories complete all as specified and as directed.. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured for payment purpose.) |
| 57 | S & F for 5.50 mm thick sheet glass, ordinary quality and glazing in aluminium door frames with beading Complete all as specified and as directed. |
| 58 | S & F in repairs figured glass, pin head type sheet glass 4.0 mm thick ordinary quality and glazing with aluminium glazing clip in aluminium window shutter not exc 0.5 Sqm in each pane complete all as specified and as directed. |
| 59 | Providing and fixing factory made uPVC white colour fixed window/ Ventilator made of extruded profiles with wall thickness of 2.3mm(+-0.2mm). Window profile with hollow section with multi chamber. Frame (60mm x 58mm). T profile (Onevertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc. making arrangement for fixing of hardware, EPDM gasket. 1.2 +–0.2mm thick, galvanized steel Frame (28mm x 21.5mm), T profile (27mm x 17 mrn) to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners- 5mm thick glazing with selected quality glass complete all as specified and as directed.(Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories Net opening will be measured for payment purpose.) |
| 60 | S & F of 18 mm thick plywood BWR type fixed with screws with timber framework complete all as specified and as directed. |
| 61 | M & L for 0.9 mm thick colour / white laminates type I or surface finish, colour and pattern fixed to wooden surface with glue complete all as specified and as directed . |
| 62 | S&F Stainless steel 304 grade wire Basket of pull out type like lain/cup & saucer/bottle/multi purpose/2-3 shelf baskets etc for kitchens of required size & Shape Complete all as specified and as directed. |
| 63 | S & F of 30 mm width of flap Continous (Piano) hinges, mild steel, bright finish or electro galvanised complete all as specified and as directed. |
| 64 | S&F for aluminium anodised 100 mm hasp and staple, safety type, brass with mild steel hing pin incl bolt to hinge plate and fixed with screws complete all as specified and as directed. |
| 65 | S&F aluminum anodized barrel bolt of extruded section 125mm long, complete all as specified and as directed |
| 66 | M & L for prepartion of new wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and as directed. |
| 67 | S&F butt hinges extruded aluminium alloy with galvanized mild steel hinge pin ,anodized of hinges 100 mm type B-21 complete all as specified and as directed |
| 68 | S&F of extruded aluminum alloy handle fabricated type anodized 150mm long complete all as specified and as directed. |
| 69 | S&F of aluminum anodized barrel bolt of extruded section 150mm long complete all as specified and as directed. |
| 70 | S&F of magnet catcher for cupboards or wordrobe etc complete all as specified and as directed. |
| 71 | S&F of stainless steel drawer channel and ball bearing slide telescopic channel for cabinet or cupboard complete all as specified and as directed. |
| 72 | S&F of 300mm mild steel , ordinary rat tail rod pattern springs including roller and roller plate etc complete all as specified and as directed |
| 73 | S&F for 300mmlong aluminium alloy, anodised sliding door bolt with hasp staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed etc complete all as specified and as directed. |
| 74 | S&F floor door stopper of aluminium alloy body & tongue, anodised with hard drawn spring of 140mm size fixed in floor complete all as specified and as directed |
| 75 | S&F in repairs stainless steel curtain rail, cromium plated with fixing brackets, stops, roller etc complete all as specified and as directed. |
| 76 | S&F in repair rotational moulded polyethylene water storage tanks 1000 lts (cylindrical vertical with closed top) hoisted and fixed in position incl taking downold pvc tank complete all as specified and as directed. |
| 77 | S&F in repair rotational moulded polyethylene water storage tanks 500 lts (cylindrical vertical with closed top) hoisted and fixed in position, including dismantling of old water tank and removing to store complete all as specified and as directed. |
| 78 | S&F 25mm ball valve high pressure with polythylene float valve and fly nut complete screwed for iron pipe PTMT complete all as specified and as directed. |
| 79 | S & F Gun metal globe or gate valve 20mm , with iron wheel head screwed both ends for iron pipe and loud in repairs complete all as specified and as directed. |
| 80 | S & F in repairs vitreous china wash down single piece WC of size 410x720x800mm with softclose seat cover with 'S' or 'P' trap and other connecting items approved brand including fix with white cement complete all as specified and as directed. |
| 81 | S&Fin repairs Health faucet (ABS body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect complete all as specified and as directed. |
| 82 | S & F in repairs vitreous china WHB white flat back size 630 x 450 mm rectangular shape table top approved brand incl bottle trap waste fitting complete all as specified and as directed. (Make- Jaquar/Prayag/Somany ) |
| 83 | S&F in repairs vitreous china ware wash down white water closet pan (pedestal pattern with trap incl connecting to drain and flushing pipe, antisyphonage pipe incl PVC sheet cover etc complete all as specified and as directed. |
| 84 | S&F in repair PVC valveless syphonic action type flushing cistern 10 ltr capacity white with inlet ball valve float flush pipe and handle including brackets complete all as specified and as directed. |
| 85 | S&F in repairs vitreous china ware wash hand basin white flat back of size 550x 400 mm with pedestal including brackets, 32 mm CP waste coupling, chain and plug, waste fittings, and all necessary inlet, out let connections complete all as specified and as directecl. |
| 86 | S&F in repairs 15 mm bore pillar taps, cast copper alloy, chromium plated fancy type screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts complete all as specified and as directed. |
| 87 | S&F in repair CP long body Bib taps/two- way Bib taps fancy type Chromium plated cast copper alloy with crutch or butterfly handle, screwed for iron pipe of dia 15mm, fancy type complete all as specified and as directed. |
| 88 | S&F CP Stop valves/angle cock cast copper alloy,fancy type,with long shank and cup, bore15mm, fixed complete all as specified and as directed |
| 89 | S&F in repairs PVC connection 15mm dia and 45cm long with two Nos of brass checknuts and washers complete all as specified and as directed. |
| 90 | S & F in repairs bevelled edged looking mirror of size not exc 2 Sqm of selected quality glass fixed with stainless steel studs all as specified & directed including taking down existing old unserviceable mirrors complete all as specified and as directed. |
| 91 | S & F of soap-dish chromium plated (Approximate size 160mmx160mmx90mm) complete all as specified and as directed. |
| 92 | S & F Brass chromium plated towel rack with lower hanger (stainless steel) with hook complete all as specified and as directed. |
| 93 | S&F Brass chromium plated tubular towel ring square/round with round flange complete all as specified and as directed. |
| 94 | S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and as directed. |
| 95 | S&F double bowl sink made up of stainless steel 1mm thick glossy matte fininsh for kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 1420mmx570mm, bowl size 600mm x 450mm x 250mm complete all as specified and as directed. |
| 96 | S & F central hole basin mixer with chrome finish complete all as specified and as directed |
| 97 | S & F of swan neck sink cock tap 15 mm with silver, chrome finish complete all as specified and as directed. |
| 98 | S & F in repairs for wall mixer 3-in-1 system with provision for both hand shower and over head shower composite with 115 mm long bend pipe connecting legs & wall flanges Mixer hand shower including 1.5 mtr flexible tube with hook Cat No BHS-87, and over head showerwith arm and flange(300mm) complete all as specified and as directed. |
| 99 | S & F kitchen plate rack size (900mmx750mm) made of stainless steel, complete all as directed and as specified |
| 100 | Dismantling of cast iron drain pipe 100 mmdia from floor/walls etc and taking out of trenches/floors complete all as specified and as directed. |
| 101 | S&F 110 mm PVC (SWR) pipes single socket in any length with rubber ring joints fixed to wall complete all as specified and as directed. |
| 102 | S&F 110 mm PVC (SWR) bends any radius with access door complete all as specified and as directed. |
| 103 | S&F 110 mm PVC (SWR) branch piece, (singal T) equal or unequal with access door complete all as specified and as directed. |
| 104 | S&F 110 mm PVC (SWR) vent cowl complete all as specified and as directed. |
| 105 | S&F 110 mm PVC (SWR) pipes single socket in any length with rubber ring joints fixed to wall as in rain water pipe complete all as specified and as directed. |
| 106 | S&F 110 mm PVC (SWR) bends any radius with access door complete all as specified and as directed. |
| 107 | Dismantling of cast iron drain pipe 75mm dia from floor/walls etc and taking out of trenches/floors complete all as specified and as directed. |
| 108 | S&F 75 mm PVC (SWR) pipes single socket in any lenth with rubber ring joints fixed to wall complete all as specified and as directed. |
| 109 | S & F 75/110mm dia, PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed. |
| 110 | S&F 75 mm PVC (SWR) bends any radius with access door complete all as specified and as directed. |
| 111 | S&F 75 mm PVC (SWR) branch piece, (double T) equal or unequal with access door complete all as specified and as directed. |
| 112 | S&F 32 mm bore CPVC pipes SDR 11 pipes & Plain CPVC SDR 11 fittings and fixed complete to walls and ceiling or laid in floors including taking down complete all as specified and as directed. |
| 113 | S&F 25 mm bore CPVC pipes SDR 11 pipes & Plain CPVC SDR 11 fittings and fixed complete to walls and ceiling or laid in floors including taking down complete all as specified and as directed. |
| 114 | S&F in repairs of CPVC pipes 20 mm dia SDR 11 & plain CPVC SDR 11 fittings in wall /ceiling or laying in floors taking down old GI tubes complete all as specified and as directed. |
| 115 | M & L for TMT bars 10 mm dia and over and cut to length bent to shape required including cranking, bending, hooking ends and bending with MS wire not less than 0.9mm dia or securing with clips quality conforming complete all as specified and as directed. |
| 116 | M&L for PCC (1:4:8) type D2 using 40mm graded crushed stone aggregate as in 100mm thick as in sub base complete all as specified and as directed. |
| 117 | M & L for hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and as directed. |
| 118 | Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc. of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed. |
| 119 | Excavation in trenches by mechanical means (Hydraulic excavator) or mannual exc n.exc. 1.5m wide and n.exc. 1.5m in depth for taking up/laying sewer lines and getting out in any kind of soil all as specified and as directed. |
| 120 | Returning, filling in soil including spreading, levelling, watering and well ramming in layers n.exc. 25cm all as specified and as directed. |
| 121 | Removing of excavated soil to a distance n.exc 50m and depositing where directed at alevel n.exc 1.5m above starting point complete all as specified and as directed. |
| 122 | Demolition and breaking up drain pipes 150mm dia ( Salt Glazed ware, AC or reinforced concrete) set in cement mortar including PCC bed and haunching and removal of debris outside the MD land complete all as specified and as directed. |
| 123 | M&L for salt glazed stoneware pipes grade 'A',150mm bore,laid in trenches and jointed complete all as specified and as directed. |
| 124 | M&L for PCC 1:3:6 type C2 (using 40mm graded stone aggregate) for bed to drain pipe 150mm bore including packing under and haunching against the sides of pipes after they are laid and tested all as specified and as directed. |
| 125 | Demolition of reinforced Concrete in any position not otherwise specifically provided for RCC cover slab for manholes etc complete all as specified and as directed. |
| 126 | M&L for pre-cast reinforcement cement concrete (1:2:4) Type B-1, using 20 mm graded crushed stone aggregate as in cover slab for manholes etc.and set in CM 1:6 complete all as specified and as directed. |
| 127 | M&L for Plain cement concrete type C1(1:3:6) ( using 20mm graded crushed stone aggregate) as in surface chanels and drains complete all as specified and as directed. |
| 128 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and as directed. |
| 129 | M & L for taking down copper/aluminium point wiring (light, fan, socket, power, security lights or bulkhead) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc.complete all as specified and as directed. Please Enable Macros to View BoQ information |
| 130 | M & L for taking down copper/aluminium point wiring (light, fan, socket, power, security lights or bulkhead) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc.complete all as specified and as directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 30, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 19, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 1 dayAug 21, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 3 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender