Tender For Interior Work At Bulandshahr Development Authority Office Building At Bulandshahr Up.
Tender Value
3.28 Crore
Estimated cost
Bid Submission
25 Aug 2026
25 days left
EMD
6.58 Lakhs
Bank guarantee accepted
Document Fee
3540
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Hathras → Uttar Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Interior Work At Bulandshahr Development Authority Office Building At Bulandshahr Up.
BOQ
| Sl. No. | Item Description |
| 1 | Wall Paneling & False Ceiling |
| 2 | Providing and laying POP false ceiling Fixing of channal, T-Section, Cross, aluminium jali of heaviar section of more than 700gm use POP of JK Birla or eqivalant etc complete. |
| 3 | Baffle ceiling system comprises of 50 mm x 100 mm (50 mm width & 100 mm Height) U Shape panels. Panels shall be made of 0.5 mm thick galvanized steel with polyester powder coating 0f 60 microns and length up to 3600 mm. Panel shall be high corrosion resistance and good color stability. Centre to Centre panel gap will be 150 mm. Panels are fixed on to roll formed carriers 32 mm wide x 42 mm deep out of 0.50 mm G.I sheet powder coated with cutouts to hold the panels in module of 50 mm at maximum 1200 m c/c. Carriers are suspended from the roof or truss by 4 mm dia. galvanized steel wire rod hanger with special height adjustment suspension clip at max. 1200 mm c/c. Hangers are fixed to the roof by ‘J’ hooks or ceiling brackets and nylon inserts. Panels are factory cut in lengths up to maximum 3.6 m to suit site dimensions or shop drawings. Top cap and side cap are used to cover the edges of the panels. Make:- HarsonsGreen |
| 4 | Providing & Fixing of G.I open cell ceiling with 15mm Tee Grid (0.30mm) The Ceiling suspension system shall be exposed Lay-in system to fit 600mm x 600mm. It shall be suspended to the soffit by 4mm diameter adjustable quick it hanger rod system. Main tee shall be 32mm height exposed portion (Polyester coated) shall be 15mm. Cross tees shall be 32 mm height and exposed portion is 15mm.All system components are made of roll formed hotdipped galvanized steel of 0.30mm thickness with zinc coated of 100gsm/m2 and a minimum tensile strength of 240 mpa. Wall angle shall be 20mm heightand exposed portion shall be 20mm made of 0.35mm thick pre coated coil. Both ends of main tee have integral splices which can be enjoyed firmly be inserting a tab on the one end of one section into slot in the adjoining section.The exposed flange finish shall be pre painted polyester coated galvanized steenot less than 0.30mm with coating thickness of 20 microns top coat and 5 microns primer alkyd backer coat on back side. Open cell ceiling system is consisting of G.I 0.35 mm thickness with 60 microns powder coating of polyester paint. Main and cross runners of open cell interlock with each otherto form into 100 x 100mm and comes in dimension of 595 mm x 595 mm, which lay-in the frame of 15 mm tee grid. Dimension of open cell main and cross runner is 15 mm x 50 mm/40 mm x 595 mm. |
| 5 | Varnishing with varnish of approved brand and manufacture : Two or more coats glue sizing with spar varnish or an under coat of flatting varnish |
| 6 | French spirit polishing : Two or more coats on new works including a coat of wood filler |
| 7 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work |
| 8 | Providing and fixing plain lining with necessary screws/nuts & bolts/ nails, including a coat of approved primer on one face, and fixed on wooden /steel frame work, complete as per direction of Engineer-in- charge (Frame work shall be paid for separately). 12mm thick commercial ply conforming to IS : 1328 BWR type |
| 9 | Providing and fixing frame work for partitions/ wall lining etc. made of 50x50x1.6 mm hollow MS tube, placed along the walls, ceiling and floor in a grid pattern with spacing @ 60 cm centre to centre both ways (vertically & horizontally) or at required spacing near opening, with necessary welding at junctions and fixing the frame to wall/ ceiling/ floors with steel dash fasteners of 8 mm dia, 75 mm long bolt, including making provision for opening for doors, windows, electrical conduits, switch boards etc., including providing with two coats of approved steel primer etc. complete, all as per direction of Engineer-in-charge. |
| 10 | Providing and fixing full-height frameless/semi-frameless glazed partition comprising 12 mm thick clear toughened safety glass conforming to IS 2553 (Part-1), fixed in powder-coated aluminium top and bottom channels with approved glazing gaskets, setting blocks and structural silicone sealant. The partition shall be provided with engineered wooden finish vertical and horizontal trims/laminated MDF feature panels as shown in drawings to achieve a wooden appearance. All exposed aluminium members shall be powder coated in approved colour. The item shall include floor channels, ceiling channels, glazing accessories, stainless steel fittings, sealants, fixing hardware, edge protection, necessary cutting, polishing, transportation, installation and making good complete as directed by the Engineer-in-Charge. (For Half Patition 0.90m to 1.20mtr Wooden Board & 0.30-0.45mm toughed Glass ) & (Full Patition 2.00m to 2.40mtr Wooden Board & 1.20m-0.45mm toughed Glass ) |
| 11 | Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.0 mm thick |
| 12 | Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete : 2nd class teak wood 50x20 mm |
| 13 | Providing and Fixing of Stretch HUSH wall fabric system, By using Hush Fabric of size 1400mm width, shall be stretched by using wooden base 10mm thick and rigid vinyl Stretch Tracks full wrap 15mm (FS15) and Midseam 15mm (FS15), strand board, synth PF infill with requisite accessories & tools strand square edge magnesite bonded finewood fibre panels of size 600 x 1200 x 15 mm having density 400 Kg per cum and weight 4 Kg or more is fixed to existing frame work in between vinyl tracks with suitable fasteners Synth PF 10 x 10 mm thick shall be pasted on strands panels using suitable adhesive. Installation- Wooden base 10mm is installed along the marking lines with metal fasteners inserted at 300mm centers. FS15 fullwrap tracks to be installed on wooden base, at free edges,after applying adhesive on both surfaces for a true and continuous secure grip, and heavy-duty fasteners at 150mm centers on one/both sides of Stretch Tracks.Track outer corner should be installed on woodenbase at corners of column projection.Fabric of width 700mm is then aligned to the Stretch tracks by following the fabric thread line or pattern. The fabric is stretched and tucked into the Stretch tracks and secure into the locking jaws so that it will be smooth, free of wrinkles with the tucking tools. Note -minimum 50mm additional fabric is required for tucking hence maximum module wall fabric width would be 1600mm. The fixing need to be approved from Engineer in charge as per approved design of panels & requirement at site. Nothing extra shall be paid and only finished panelling area shall be measured for payment. |
| 14 | Providing and Fixing of ‘Wooden Slats’ 2430x131 mm with thickness of 16 mm MDF backed with acoustical Fleece providing sound absorption of NRC 0.70 tested as per IS:8225- 1987.To be installed with 15mm Aluminium profile conforms to Aluminium Alloy 6063-T 6.Temper As per BS:1474-1987 and G.I Lock in clips on the back of tongue and Groove system. The density per panel is 750-800 kg/m3.The panels come with tongue & groove for seamless patterns, 2-14mm Groove and visible panel.Wooden slats are made from acoustical fibreboard with linear perforations for excellent uniformity. The perpendicular holes should be available on the back of panel which are covered by black acoustical fleece.INSTALLATION: ‘Wooden Slats’ can be installed on G.I studs 600x600mm centre to centre 2400mm X 50mm web thickness 0.5mm, flanges 15 & 50mm fully knurled giving it high strength, hot dipped galvanized steel with 120GSM zinc coating specially designed for Acoustic vibration management and long life with a backing of 50mm thick,1000 GSM Acoustic Wool tested as per Fire Retardant ASTMD 635-1991/Insulation and IS 15061-2002 for excellent results. |
| 15 | Granite stone slab all colour except black, cherry/ruby red 18 mm thick (slab area above 0.50 sqm) of thickness 18 mm for wall lining (veneer work), backing filled with a grout of average 12 mm thick in cement mortar 1:3 (1 cement : 3 coarse sand), including pointing with white cement mortar 1:2 (1 white cement : 2 marble dust) with an admixture of pigment to match the marble shade (To be secured to the backing by means of cramps, which shall be paid for separately). |
| 16 | Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineerin-Charge. Granite Work |
| 17 | Providing and laying full Body Vertified Tiles in floor of 600x600mm sizes (thickness 9mm) with water absorption less than 0.08% and confirming to IS: 15622, of approved brand manufacture, in desired colour and shades, laid with cement based high polymer modified quit set tile adhesive (water based) confirming to IS :15477, including grouting of joints. All complete as per direction of E/I (Matt Finish/Glossy) |
| 18 | \\"Providing and fixing customized capsule-shaped signage/nameplate of approved size (approx. 300x600mm or as specified), fabricated using 3mm to 5mm thick high-quality acrylic base with premium wooden texture finish. The item shall include laser-cut 3D acrylic letters/numbers (white color) duly fixed on the base. Complete with double-sided spacer tape/studs, hardware, and installation on walls or doors as per the direction of the Engineer-in-Charge.\\" |
| 19 | LED Down lighter (COB Type) (System lumen efficacy ≥120 lm/Watt )Supplying, Installation, Testing & Commissioning of LED Recessed/surface Down lighter (Round / square/ Rectangular) COB Type of following body material and construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range -5 °C to 40 °C, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI ≥80 , UGR (Unified Glare Rating) < 19, Flicker free (flicker should be below 5 %), life time (LED, Driver & electrical circuitry), life time of minimum 50000 Burning Hours with, 70% of initial Lumen maintained till life ends , CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation Colour Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard. Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab Eachup for all testing facilities for LED fixtures. \\"complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥120 <135 lm/Watt output . LM79 & LM80 Test report and all testing required |
| 20 | 22 watt |
| 21 | 30 watt |
| 22 | Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. 1 run of cable |
| 23 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable in surface/ recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable etc. as required. Group A |
| 24 | Wiring for twin control light point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable in surface / recessed steel conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS/HFFR PVC insulated copper conductor single core cable etc .as required. |
| 25 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings). |
| 26 | Supply and fixing of LED Tube Light with batten suitable for up to 1 X 22 watt LED tube light fitting including tube on Surface complete in all respect. CAT- AAA |
| 27 | TELEVISION WORK (TV) |
| 28 | SSupply, Installation, Testing, and Commissioning (SITC) of Real QLED 4K AI Smart Television set of approved brand (Samsung or equivalent), 138 cm (55 inches) screen size, model reference QA55Q8FAAULXL (p. 1), featuring Ultra High Definition (UHD) 4K resolution (3840x2160 pixels) (p. 14), Real Quantum Dot Display with blue LED and cadmium-free Quantum Dot sheet (p. 3), Q4 AI Processor (pp. 3, 14), minimum 120Hz refresh rate (native) (p. 18) with Motion Xcelerator (p. 8), Quantum HDR (p. 1), Color Booster Pro scene recognition (p. 8), and 100% Color Volume measured to DCI-P3 standard (p. 6); embedded audio system featuring Q-Symphony simultaneous sync with compatible soundbars (pp. 2, 9), Object Tracking Sound, and Adaptive AI sound processing (p. 5); Smart TV platform running on One UI Tizen OS with guaranteed 7 years upgrades (p. 10), integrated Samsung Vision AI companion (p. 1), SmartThings & Matter smart home hub compatibility (pp. 11-12), Samsung TV Plus (125+ free channels) (pp. 3, 10), and Universal Gestures via compatible smartwatch (p. 12); physical attributes including ultra-slim AirSlim Design (pp. 1, 12) and height-adjustable table-top side stands (p. 13); inputs comprising minimum 3 Nos. HDMI ports, USB ports, built-in Wi-Fi, Bluetooth, and RJ-45 Ethernet; complete with factory-bundled standard accessories including SolarCell Remote Control (charged by light/USB-C) (p. 14), power cable, as required. all complete as per site-in charge. |
| 29 | BLINDS/CURTAIN WORK |
| 30 | Providing and fixing 18 mm thick, 150 mm wide pelmet of flat pressed three layer or graded plain wood particle board medium density grade I, ISI marked and conforming to IS : 3087 marked, including top cover of 6 mm commercial ply wood conforming to IS: 303 BWR grade, nickel plated M.S. pipe 20 mm dia ( heavy type) curtain rod with nickel plated brackets, including fixing with 25x3 mm M.S. flat 10 cm long fixed to pelmet with hollock wood cleats of size 100 mm x 40 mm x 40 mm on both inner side of pelmet and rawl plugs 75 mm long etc. all complete. |
| 31 | Extra for using veneered particle board conforming to IS 3097 Grade I, in item of pelmet 18mm thick 150mm wide. Non decorative veneer on both sides |
| 32 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture |
| 33 | Providing and fixing chromium plated brass curtain rod having wall thickness of 1.25mm with two chromium plated brass brackets fixed with C.P. brass screws and PVC sleeves etc., wherever necessary complete : 25 mm dia |
| 34 | Providing & Fixing Zebra Ready Blind with Pelmet multicolor in vertical/horizontal pattern, suitable for hospital and office use. All Complete as per Site-in Charge |
| 35 | GRC JALI FOR EXTERIOR WORK |
| 36 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 37 | Providing and fixing Glass Fibre Reinforced Concrete (G.F.R.C.) architectural screen jali of overall 30mm thickness, casted using an approved design mix with alkali-resistant glass fibres. The jali shall be fabricated in approved sizes, patterns, and smooth finish/shade as per architectural drawings.The elements shall be securely fixed using 'Dry Fixing' method over a rigid structural framework (like R.C.C., brickwork, or epoxy/red-oxide painted MS frame) with heavy-duty stainless steel (SS 304) clamps, fasteners, and anchor bolts of approved make (such as Fischer/Hilti). The rate shall include the cost of scaffolding, lifting, alignment, sealing joints with approved polyurethane/silicone sealant, making the installation neat and complete as per the instructions of the Engineer-in-Charge. (Payment will be done on the basis of actual front elevation area fixed).\\" |
| 38 | Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after .The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineer-in-charge .The elevational area of the scaffolding shall be measured for payment purpose .The payment will be made once irrespective of duration of scaffolding. Note: - This item to be used for maintenance work judicially, necessary deduction for scaffolding in the existing item to be done. |
| 39 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 30, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 25, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 25 daysAug 26, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 26 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender