Tender For Supply Of Electrical And Electronics Engineering Department Lab Equipments Are Required As Per New Syllabus

Sharing tender

Tender for Supply Of Electrical And Electronics Engineering Department Lab Equipments Are Required As Per New Syllabus , Upgradation Of Labarotaries Ece Department , 8051 Micro Controller Kit • Operating Voltage: +5 V Dc. • Flash Memory: 4 Kb (At89c51) / 8 Kb (At89s52). • Ram: 128 Bytes Internal Ram. • 16 × 2 Alphanumeric Lcd Display. • Push Buttons / Tactile Switches. • Dip Switches For Digital Input. • Inbuilt Adc Interface: Ldr, Potentiometer. • Inbuilt Dac Interface. • Inbuilt Stepper Motor Driver With Stepper Motor. • Inbuilt Dc Motor Driver With Dc Motor. • 1 × 4 Led Array, 1 × 4 Keypad, 1 × Relay. • 1 × Buzzer, 16 × 2 Lcd Display, 1 × Pwm Driver. • 1 × Hardware Interrupt Key, Inbuilt Rtc. • Inbuilt Eeprom And Uart Module. • 4 × 7-Segment Display. • Supports Both Assembly And C Language Programming. • Pc Interfaceable. , Single Phase Induction Motor 1 Hp, 230 V Ac, 1500 Rpm With Loading Arrangement - 1 No. Voltmeter: (0-300) V Ac, 96 × 96 Mm With Input Terminals - 1 No. Ammeter: (0-10) A Ac, 96 × 96 Mm With Input Terminals - 1 No. Wattmeter: 2 Kw, 96 × 96 Mm With Input Terminals - 1 No. Power Factor Meter: 96 × 96 Mm With Input Terminals - 1 No. Auto Transformer: 0-300 V, 1Φ Variac - 1 No. Mcb: 2-Pole, 40 A / 230 V Ac - 1 No. Digital Rpm Indicator With Proximity Sensor - 1 No. Aluminium Brake Drum: 230 Mm Diameter - 1 No. Spring Balance: (0-25) Kg - 02 Nos. Circuit Diagram Printed On Front Panel With Instruments And Connecting Terminals. Motor And Loading Arrangement Mounted On Rigid Channel Frame With Anti-Vibration Mounting Pads, M12 × 1.5 Bolt & Nut, 85 Mm Dia - 4 Nos. Mild Steel Powder-Coated Electrical Panel Table Setup. , Auto Transformer Input: 230-240 V Ac, 50 Hz. Output: Variable (0-270) V Ac. Rating: 1 Kva. Insulation Class: Class F / Class H. Construction: Copper Winding With Carbon Brush Arrangement. Mounting: Bench-Top / Panel Type. Protection: Suitable Fuse / Overload Protection. , Dth Trainer Kit Power Supply: • 200 V To 240 V Ac, 50 Hz. Dish Antenna: • 1.5 Ft Aluminium Steerable Dish Antenna. Lnb (Low Noise Block Down Converter): • Input Frequency: Ku-Band. • Output Frequency: 950 Mhz To 1450 Mhz. • Conversion Gain: 65 Db. • Noise Temperature: 35 K (Max). Set-Top Box Receiver In Trainer Form: • If Frequency: 70 Mhz. • Video Bandwidth: 50 Hz To 5 Mhz. • Video Output Level: 1 Vpp At 75 Ω Load. • Video Polarity: Normal/Inverted, Switch Selectable. • Audio Subcarrier Frequency: Tunable From 5.0 Mhz To 8.0 Mhz. • Remote Control Provided. • Hdmi Cable: 10 M. Controls: • Channel Selection. • Volume Control. Fault Simulation: • Five Built-In Simulated Faults For Troubleshooting Experiments. • If Signal Disconnected. • Video Output Fault. • Audio Mute Fault. • Tuner Misalignment. • Rf Output Interruption. Pcb Size: • 15 × 12 With Multicolour Section-Wise Block Diagram. Standard Accessories: • 1.5 Ft Dish Antenna. • Lnb. • Trainer Pcb. • Dish Connecting Wire.• Audio-Video Cable. • User Manual. • Acrylic Cover.• Hardware Materials For Assembly Of Dish Antenna. Additional Features: • Dth Subscription Connection With Doordarshanfree Channels. , Sim Reader Trainer Kit Power Supply: • Operates On 230 V Ac ±10%, 50 Hz Mains Supply. • Built-In Regulated Smps Power Supply. • Operating Dc Supply: 5 V / 12 V With Overload And Short-Circuit Protection. Sim Card Interface: • Supports Gsm Sim Cards Compatible With 2G / 3G / 4G / 5G Networks. • Sim Card Read/Write Interface. • Supports Sim Card Initialization, Authentication, And Communication Functions. • Compatible With Standard 6-Pin / 8-Pin Sim Card Sockets. Communication Interface: • Usb 2.0 Interface For Pc Communication. • Rs-232 Serial Communication Interface. • Uart Communication Facility For Embedded System Interfacing. Sim Operating Parameters: • Selectable Sim Clock Frequencies: • 3.579 Mhz • 7.159 Mhz • 14.318 Mhz • Sim Supply Voltage Selection Facility. • Sim Reset And Activation Control. Supported Protocols And Standards: • Gsm Etsi 07.07 And Etsi 07.05 At Command Support. • Iso/Iec 7816 Smart Card Communication Support. • Sim Communication Command Monitoring Facility. Hardware Features: • On-Board Sim Card Socket. • Led Indication For: • Power Status • Sim Detection • Reset Activity • Data Transmission/Reception • Built -In Keypad For Standalone Operation. • Lcd Display Module (128 × 64) For Menu And Status Display. • On -Board Microcontroller -Based Control Section. Software Support: • At Command Execution And Monitoring Software. • Sim Manager Utility Software.• Data Logging And Communication Terminal Utility. • Pc -Based Gui Software For Sim Data Communication Experiments. Trainer Features: • Fault Simulation Facility For Troubleshooting Experiments. • Simulation Of Faults Such As: • Sim Not Detected • Clock Failure • Vcc Failure • Reset Failure • Multiple On -Board Test Points For Signal Observation. • Test Points For: • Sim_Rst • Sim_Clk • Sim_Io • Vcc • Uart Tx/Rx • Suitable For Cro/Dso Signal Monitoring. • Glass Epoxy Pcb With Educational Block Diagram Layout. • Compact Tabletop Enclosed Cabinet Design. Construction: • Front Panel With Printed Block Diagram.• Banana Test Points And Patching Facility. Standard Accessories: • Gsm Sim Trainer Unit. • Usb Communication Cable. • Rs-232 Communication Cable. • Power Cord. • User Manual. • Utility Software Cd / Downloadable Software Package. , Fpga Trainer Kit • Must Use Industry-Standard Mid-Range Fpga Device • Usb-Jtag Programmable, Compatible With Vivado Ise (Webpack). • Power Supply: 5 V Dc Through Usb Or External Adapter. • On-Board Peripherals: Leds, Switches, Push Buttons, 7-Segment Display,Clock Source, Gpio / Pmod Expansion Ports, Uart, Vga / Hdmi, Usb-Uart Bridge, Usb Cable. •User Manual.