Tender For Comprehensive Maintenance Work At Nsb-I Chanakyabagh, Chanakyapuri Under Ge New Delhi.
Tender Value
75 Lakhs
Estimated cost
Bid Submission
27 Aug 2026
12 days left
EMD
1.37 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
New Delhi → Delhi
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Comprehensive Maintenance Work At Nsb-I Chanakyabagh, Chanakyapuri Under Ge New Delhi.
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling floor hearth or wall tiling including cement mortar bedding and rubbish off the premises complete all as specified and as directed. |
| 2 | M&L for SGVT ceramic light shade matte/ Glossy finish tiles 10 mm thick (square /rectangular) area of each tile exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors set and jointed in neat cement slurry and pointed with white or coloured cement laid over 15 mm thick Screed bed or bedding layer of cement mortar 1:6 complete all as specified and directed. (Colour and pattern of tile as approved by EIC and work to be execute through skilled labour) Make :- Kajaria or equivalent in Somany /Johnsion/ Nitco |
| 3 | M & L Glazed vitrified coloured tiles of 10 mm thick in glossy / matte finish with size 2 x 4 feet (600 x 1200 mm) fixed in vertical surface with 10 mm thick backing layer of good quality tile adhesive (MYK Laticrete 325+ / Roff) (qty of water should be mix as per manufacturere's instruction) fix to wall, joint shall be kept as 3mm filled with epoxy. to attain the best result 3 mm thick tile spacers to be used,Masking tape shall be put before putting the eposy grout & the grout shall be throughly cleaned immendiatlycomplete in all respect as specified. (Colour and pattern of tile as approved by EIC and work to be execute through skilled labour) Make :- Kajaria or equivalent in Somany /Johnsion/ Nitco |
| 4 | M & L Virified Ceramic tiles light colour 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick cement screed 1:6,complete in all respect as specified. |
| 5 | All as per item No. 4 here-in-before but on vertical surfaces over and including 10 mm thick plaster in cement mortar 1:4 complete all as specified and as directed. |
| 6 | M&L for glazed coloured ceramic tiles in dado/vertical surface (300mm x600mm x 7-8 mm) thick fixed with chemical adhesive Fevi Mate of equivalent and joint shall be kept as 3mm filled with epoxy. to attain the best result 3 mm thick tile spacers to be used,Masking tape shall be put before putting the eposy grout & the grout shall be throughly cleaned immendiatly, complete all as specified and directed. |
| 7 | M & L Non skid joint less coloured ceramic tiles 7-8mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed by Engr in charge. (approved by EIC) Make :- Somany or equivalent in Kajaria/Johnsion |
| 8 | M & L Glazed ceramic coloured tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over including screeding 10 mm thick in CM 1:4 on wall complete in all respect as specified. Colour and pattern approved by EIC) Make :- Somany or equivalent in Kajaria/Johnsion |
| 9 | Taking up or down steel tubing and connections of 15mm bore dia of pipe including cleaning for refixing or removal to store complete in all respect as specified |
| 10 | Taking up or down steel tubing and connections of 20mm bore dia of pipe including cleaning for refixing or removal to store complete in all respect as specified |
| 11 | Supplying and laying of 20 mm dia CPVC pipes SDR 11 fittings on walls / ceiling or laying in floors including cement solvent and all fitting complete all as specified. |
| 12 | Supplying and laying of 25 mm dia CPVC pipes SDR 11 fittings on walls / ceiling or laying in floors including cement solvent and all fitting complete all as specified. |
| 13 | S & F 20 mm dia Brass Elbow |
| 14 | S & F Union 16 / 20 mm |
| 15 | S & F 20 mm dia Brass Tee |
| 16 | Dismantling 100mm/75mm dia bore cast iron soil, waste and vent pipes including fitings by burning out lead joints etc |
| 17 | S & F 110 mm dia PVC (SWR) pipes 5 mm thick (6 kg/ cm2) pressure pipe, single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed. Make:- Finolex / Supreme/ Vectus |
| 18 | S & F 75 mm dia PVC (SWR) pipes 5 mm thick (6 kg/ cm2) pressure pipe, single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed. Make:- Finolex / Supreme / Vectus |
| 19 | S & F 110 mm PVC (SWR) bends any radius |
| 20 | S & F 110 mm PVC (SWR) junction single, (Single T) equal or unequal |
| 21 | S & F 110 mm PVC (SWR) Cowl |
| 22 | S & F 75 mm PVC (SWR) bends any radius |
| 23 | S & F 75 mm PVC (SWR) junction single, (Single T) equal or unequal |
| 24 | Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings,heads, shoes, bends, swan-necks,etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) |
| 25 | S&F MS Bands, straps, supports or stays for rainwater, ventilating pipes,including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to FE-290 Gde-E-165 |
| 26 | S&F in repairs 20mm bore gun matel globe or with iron wheel, screwed both ends for iron pipes fixed complete in all respect as specified |
| 27 | S&F in repair SLS-WHT-6953BIUFSM (Size : 375x520x400 mm) / Cera Code : A1044116 (Size : 600x410x430 mm) / Kohler Code : K-16817IN-SS-0 in white colour Rimless, Blind Installation Wall Hung WC with UF soft close cover, Hinges and accessories set, incl single piece slim concealed cistern body in white finish Jaquar code: JCS-WHT-2400 / Cera Code :D1110105 / Kohler Code : K-26353IN-P-NA, Pneumatic tank 3/6L with full frame with installation kit with Pneumatic faceplate flush control plate kubix Jaquar code: JCP-BGP-352415 / Cera Code :D1120121 / Kohler Code : K-75890IN-P-RGD of colour Blush Gold PVD incl required accessories and fixture, making all connection to make it functional incl make good complete in all respect as specified and directed. |
| 28 | Supply and fixing in repairs floor mounted coupled star white one piece water closet (Pedestal pattern) (Italian collection) premium class of cat part No 92551 (S-22) 70 x 38 x 73 Cm with P or S of size 220 mm, EWC with inbuilt sensor for touchless flushing, ensure more hygiene, slow falling seat cover, Elegant design, Easy clean, I trap including soft closed seat cover, hinges fixing accessories set and accessories set, incl flushing cistern, with cistern fittings connection to drain or (outgoing pipe) & to flushing pipe anti syphonage pipe etc. complete in all respect as specified and directed. Make : Hindware cat part No 92551 (S-22) 70 x 38 x 73 Cm or equivalent in Kohler / Jaquar |
| 29 | S&F Vitreous China urinals, half stall bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe |
| 30 | S&F Urinal spreader of brass chromium plated any for fixing with 15 mm dia pipe complete all as specified and directed |
| 31 | Taking down chowkats or frames not exceeding 1.5 Sqm each but with shutters (without taking off the shutter from the frame) all as specified. |
| 32 | Taking down chowkats or frames exc 1.5 sq. m but n exc 4 sq. m (without taking off shutters from the frame) all as specified. |
| 33 | M&L for Providing and fixing factory made uPVC white colour casement (Openable) Door made of extruded profile wilh wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with mitlti chamber, frame (60mm x 58mm), sash (60mm x 78mm). T profile (One vertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling ol holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 + -0.2mm thick galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27mm), T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall wilh 8mm x 100mm long fasteners. Hardware: [casement door handle made of zinc alloyed (white powder coated). Corner striker. Secondary Strikers. Cylinder. Door transmission gear made of mild sleel with multi point locking system with strikes. 3D Hinges of zinc alloyed (white powder coated) [and 5mm thick glazing with selected quality glass. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose.) |
| 34 | M&L for Supply and fixing factory made uPVC white colour Casement window single panel with S.S. friction hinges (300 x 19 x 1.9 mm), made of (small series) frame 47 x 50 mm & sash 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glass pane glazing bead of appropriate dimension (Area of window upto 0.75 sqm.) comprising of uPVC multichambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 35 | S&F aluminium ventilator with outer frame 40mmx114mm with 1.3mm thickness corner 45 degree cut & aluminium welded center mullion size 40mmx65mm partly glazed/ gauzed including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading. screws, including 0.45mm nominal dia of SS wire mesh and average width of aperature 1.18mm, including 3mm clear glass both side EPDM rubber gasket etc. provision for fixing the exhaust fan complete all as specified and as directed. |
| 36 | S&F for factory made single extruded WPC (wood polymer composite) solid door/window/Ceosetory windows and other frames/chowkat of size 125mmx65 mm comprising of virgin PVC polymer of K value 50-60(Suspension Grade), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame dencity of 750kg/cum, screw withdrawl strength of 200N (Face and 1100N edge), minimum compressive strength of 58N/Sqmm and resistance to flame of class A category and property of being termite/borer proof, water/moiture proof and fire retardant and fixed with MS hold fasts/lugs/SS Dash fastener of required dia and length of complete as per direction of Engr in charge.Note : For WPC solid door /windows frames, minus5mm tolerance in dimension ie depth and width of profile dimension on plus side shall be acceptable but no extra payment on this account shall be made. Make- Alstone/ Yashpoly/ Century. |
| 37 | S&F for factory made single extruded WPC (wood polymer composite) solid door/window/Ceosetory windows and other frames/chowkat of size 100mmx50 mm comprising of virgin PVC polymer of K value 50-60(Suspension Grade), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame dencity of 750kg/cum, screw withdrawl strength of 200N (Face and 1100N edge), minimum compressive strength of 58N/Sqmm and resistance to flame of class A category and property of being termite/borer proof, water/moiture proof and fire retardant and fixed with MS hold fasts/lugs/SS Dash fastener of required dia and length of complete as per direction of Engr in charge.Note : For WPC solid door /windows frames, minus5mm tolerance in dimension ie depth and width of profile dimension on plus side shall be acceptable but no extra payment on this account shall be made. Make- Rajshree/ Yashpoly/ Century |
| 38 | Providing 30mm thick FACTORY-MADE WIRE MESH SOLID WPC DOOR SHUTTER consisting of Density 650 Kg /Cbm Manufactured by an ISO-9001-2015 certified Company, Door to be panelled with SS mosquito Mesh and XTN aluminium Mesh for additional strength and safety purpose. (Confirming as per IS:4020). The door should be water proof, termite proof, fire retardant and having screw holding capacity. Door to be fixed to frame with 3 nos. SS butt hinges size 100mmx25mmx2mm and 32mm long steel screws drilled suitable to pass through Other hardwares shouldbe fixed with 19mmx6mm size steel screws etc. Complete as per direction of Engineer-in-charge, manufacturer's specification & drawings.\\" Note: fixture /fittings shall be measured and paid under relevant items. Make- Alstone/ Yashpoly/ Century |
| 39 | S&F Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)complete all as spd and directed. Make- Alstone/ Yashpoly/ Century |
| 40 | Supply and fixing WPC Cup Board made of 18 mm thick (solid WPC sheet) (Plus / minus 0.7) celuka WPC ply complete for hold of shelf / partition and shall provide 3 edges in sizes 18 mm x 18 mm as per required length. the edges of shelf / partition / wall side to be lipped with 18 mm x 1 mm thick WPC sheet of density 600 Kg /cbm manufactured by as ISO -9000 certified company , using solvent cement etc.( including all necessary Aluminium hardware fitting i.e Piano hinge , 4 handles, ball catchers including locking arrangement in each Cup board including dismantling of existing complete in all respect as specified and directed. (measurement should be taken external face only i.e. length and breadth) Make: Rajshree, Ecocell, Giza |
| 41 | S & F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples |
| 42 | S&F 200 mm Stainless steel barrel tower bolts of extruded section |
| 43 | S&F 150 mm Stainless steel handles, fabricated type., anodised |
| 44 | S&F SS Butt hinges in 100 mm Size, heavy weight, cold rolled Stainless steel, and fixed |
| 45 | Supply and fixed Floor door stopper 140mm long of stainless steel and tongue, anodised with hard drawn steel spring, |
| 46 | S & F 300 mm long SS sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections and fixed all as specified. |
| 47 | S&F in repair angle valve (one way) 15 mm bore cast copper alloy fancy type, cromium plated with cup complete all a specified and directed. Make- Jaquar- CAT Part No OPP-CHR-15053PM , Cera F2002201 or Equivelant in kohler |
| 48 | S&F in repair chromium plated brass two way bib tap fancy type screwed down ,screwed for iron pipe or for brass ferrule 15 mm bore complete all a specified and directed. Make- Jaquar- CAT Part No CON-CHR-041KN , Cera F 2002163 or Equivelant in kohler |
| 49 | Supply and fixed in repair 15mm bore dia Stainless steel finish quarter turn central hole basin mixer round spout with popup Waste assemly with 10mm dia , 450 mm long copper pipes complete in all respect as specified and directed by Engr-in-Charge. Make : Jaquar- CAT Part No CQT-CHR-23167B,Cera F2002461 or Equivelant in kohler |
| 50 | Supply and fixed in repair 32mm bore dia CP finish copper alloy bottle trap heavy complete in all respect as specified and directed by Engr-in-Charge. Make : cera |
| 51 | S&F in repairs chromium plated AVS health faucet Jet spary for water closet including 15mm bore PVC connecting pipe 1.2m long with check nut and washers all as specified .(Make : ZIM/PARKO/JAGUAR/SEIKO |
| 52 | Supply and fixed in repairs 600 mm long C P finish CP Towel Rail D type complete in all respect as specified and directed by Engr-in-Charge. |
| 53 | S&F in repairs vitreous china wash hand basin counter/table top type of size 495mmX395mmx150mm in 18 mm thick granite (of any type) machine cut as in platforms, bedded and jointed with grey cement slurry and pointed with white cement with admixture of of pigment to match the shade of granite stone, including 32mm bore dia CP waste coupling, waste pipe and all reuired fittings complete in all respect as specified and directed. Make: Jaquar- CAT Part No JDS-WHT-25909, Cera CAT Part No S2020163 or Equivelant in Kohler. |
| 54 | S&F in repair sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, incl pvc waste pipe and cp waste fitting, bowl size 410mmx330mmx160mm. |
| 55 | S & F in repairs PVC connections 15mm size with PTMT steel nuts of length 450mm |
| 56 | S&F in repair CP Wall mixer (wall mounted model ) 2-1 system with provision for overhead shower complete with 115mm long pipe connecting legs and flanges. Over head shower 105mm dia round shape single flow (ABS body chrome plated with gray face plate) with rubbit cleaning system Code Make- Jaquar- CAT Part No CQT-CHR-23273UPR, Cera F-2002401 or Equivelant in kohler |
| 57 | S&F in repair Brass mortice lock vertical type size 100mm & 4 lever including escutchon plate and two no of keys fixed as in repairs complete all as specified |
| 58 | S & F in repair PVC mirror cabinet of size 350 mm x 450 mm x150 mm with openable single looking mirror with PVC inner & outer shelves of any colour, including taking down old looking mirror & wooden cupboard mirror complete all as specified and directed MAKE : COMMANDER/PRAYAG/JINDAL |
| 59 | S&F in repairs CP grating 100 mm dia round fixed on floor/Nahani trap fixed with cement mortar including necessary cutting etc complete all as directed |
| 60 | Supply and fixed in repair peg set of 6 fixed with rawal plug make ;- Prayag Cat no BEA-30 |
| 61 | S & F in repair Stainless steel Double Soap Dish with tumber holder Make: Cera, Parryware. |
| 62 | S & F in repair glass made wall mounted (removable bottle) liquid Soap Dispenser Make: Cera, Parryware. |
| 63 | S&F in repairs stainless steel 20 mm dia 18 gauge pipe of required length for curtain rods including side brackets and bulbs complete all as directed |
| 64 | S & F in repair Glass Shelf assembly Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60 cm long Make - Jaquar/Cera |
| 65 | S&F in repair corner shelf (set of 03) 200mm to 300mm size 5mm thick toughened glass make :- Paryag Cat no BEA 48 |
| 66 | Demolition of stone slabs and tiles of any description or thickness in floors/walls, aprons etc laid bedded and pointed in any mortar. |
| 67 | M&L Granite (of any type) tiles 20mm thick machine cut, bedded with 20mm thick screed bed in cement mortar 1:6 and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete |
| 68 | M&L 20 mm thick granite (of any type) machine cut as in vertical surfaces and like, jointed with grey cement slurry and pointed with white cement with admixture of of pigment to match the shade of granite stone incl grinding and polishing laid over and including 15 mm thick rendering in CM 1:4 complete all as specified. |
| 69 | M&L Machine cut kota stone slab flooring 20-25 mm thick laid over 20 mm thick screed bed in cement mortar 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed. |
| 70 | M&L Machine cut kota stone 20-25 mm thick in riser of steps, skirting, dado and pillar laid over 10mm screed bed in cement mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the existing slab including rubbing and polishing complete all as specified and directed. |
| 71 | Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed. |
| 72 | M & L 15 mm thick heavy duty parking tiles 400 x 400 mm of any colour and pattern decided by Engr-In-Chargeas in pavings laid over 20 mm thick screed bed 1:6 set jointed with cement slurry mixed with pigments to match the shade of tiles complete all as specified and directed.Make : Johnson / Kajaria / Somany |
| 73 | M and L 20 mm thick Red Agra sand stone as in wall cladding, steps, footpath gang saw machine cut edges , polished, over 20mm thick cement screed in CM 1:6,set and jointed in cement mortar 1:3 and pointed in cement mixed with approved pigment to match the colour of the stone ( Note:- Size and colour of stone to be matched with existing stone) complete all as specified and directed. |
| 74 | Demolition cement concrete(reinforced) in ground floors and upto 4 storey of any description and in any position incl MS pipes Scafolding and making arrangemenets with hessian clothes for protection from falling of concrete & all other saftey precautions as in Chajjas RCC water tanks kitchen slabs etc. complete all as specified and directed. |
| 75 | M & L for Reinforced cement concrete 1:1.5:3 nominal mix, using 20mm crushed stone agg as in slab supported on walls, beams & columns in floors, roofs |
| 76 | M & L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping |
| 77 | M & L for Form work to edges of concrete flats RCC/PCC band exc 5 cm but not exc 10 cm. |
| 78 | S&F TMT bars 10mm dia and over cut to lengths bent to shape required including cranking bending and spirally hoping for columns hooking ends and binding with MS wire annealed n.less then 0.90mm dia. |
| 79 | All as item no 78 above but 6mm to 8mm dia -ditto-. |
| 80 | S&F Framed work rolled section as in framing compound girder staging for water tank,cooler stand as and the like built up from two or more beam or channel section or angles with plates stiffeners etc complete. |
| 81 | S & F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I of capacity 1000 Ltrs Incl making connection for inlet & outlet as specified & directed Engr-in-Charge and including dismantling of existing water tanks any type including ball brass valves high pressure with polythene float & flynut complete screved for Iron pipe or brass ferrule of 20 mm dia and fixedMake - Syntex, Rotex. |
| 82 | S & F in repairs ball brass valves high pressure with polythene float & flynut complete screved for Iron pipe or brass ferrule of 20 mm dia and fixed. Make -Prayag |
| 83 | Demolittion of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for all as specified. |
| 84 | M&L Providing cement concrete type B-I,1:2:4(20mm graded agg) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028 , water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed complete all as specified. |
| 85 | Taking down cement plaster on brick walls, raking out joints locking for key, scrubbing down with water etc all as specified |
| 86 | M&L for 15 mm thick rendering plaster on fair or other than faces of brick work or concrete surfaces in cement mortar 1:6 and finishing surfaces even and smooth without using extra cement complete all as specified and directed. |
| 87 | M&L Preparation of new plastered or un-plastered surface of walls and applying two coats of oil bound distemper using roller brush on walls over a coat of primer and over incl one coat of 1.50mm thick Birla putty complete all as specified and directed. |
| 88 | M&L 10 mm thick cement plaster in CM (1:4) on fair face of brick or concrete surfaces on ceiling finished even and smooth without using extra cement and using SBR latex emulsion @ 4% by weight of cement all as specified. (SBR latex shall be measured and paid separately) |
| 89 | M&L Preparation of new plastered surfaces of ceiling and applying two coats of oil bound distemper using roller brush, over a coat of primer and over incl one coat of 1.00mm thick Birla putty complete all as specified and directed. |
| 90 | M&L for complete removal of existing treatment from old surfaces of ceiling scrapping by machanical means and applying two coats of oil bound distemper using roller brush, over a coat of primer and over incl one coat of 1.00mm thick Birla putty complete all as specified and directed. |
| 91 | M&L for complete removal of existing treatment from old surfaces of wall scrapping by machanical means and applying two coats of oil bound distemper using roller brush over a coat of primer and over incl one coat of Birla putty 1.50mm thick complete all as specified and directed. |
| 92 | M&L for complete removal of existing treatment on wall/roof projections including facia, cornices etc by scrapping with mechancical sander(having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 80 grit having dia of 7\\"/9\\" to make free from dust, loose paint etc by skilled labour complete all as specified and directed. |
| 93 | M&L for water proof cement based putty @1kg (undiluted) per sqm of average thickness 2mm over the plastered /old prepared painted surface of wall and sanding of the putty surface with mechanical wall sander (having mechanical vacuum mecghanism) having RPM not less than 1500, sanding pad of 240 grit or above to make the surface . Step 1: Mix the putty powder by adding water as manufacturer's instruction and mix it with putty mixer with the mixing capacity of min 2.5 kg putty per minute. Step 2: Apply the first coat of the prepared mixer with the help of fully automatic airless spray machine/manully of putty application finishing the surface even and smooth in level without any undulations.Step 3: Allow 6-8 hrs time to dry the putty surface. |
| 94 | M&L for one coat of acrylic water based exterior grade primer @ 0.9litre(undiluted)/ 10 sqm diluted with water in 1:1 ratio to be applied with fully automatic airless spray machine and allow 6-8 hours to dry the surface for painting of subsequent coats complete all as specified and directed. |
| 95 | M&L for water based premium acrylic smooth exterior emulsion of approved colour with silicon additive excellent dirt pickup resistance with low VOC less than 50, Antifungal/ Anti Algai properties in two coats not less than 1.79 litre(undiluted)/10 Sqm diluted with water as per manufacturer's instruction applied over primed surface with fully automatic airless spray machine of paoint application with a flow speed of miniumum 1 litre per minute having a pressure of 3300PSI. Allow 6-8 hrs to dry the surface in between subsequent coats of paint complete all as specified and directed. |
| 96 | Notes for Srl item No 92 to 95:-The work for periodical services shall include the following and the rates quoted by the bidders shall include the same:-(a) The work pertaining to periodical services shall be executed by the contractor as per MoU from authorised applicator through manufacturer of the materials like Exterior Emulsion paint, putty etc after approval by the GE.(b) The contractor shall uplod with the documents under cover I \\"Memoradum of Understanding\\" (MoU) with at least one of the maunfacturers mentioned int he contract, failing which the bid hsall be laible to be rejected.(c) Use of Scaffolding, trestles, ladders, cradles etc necessary for execution of work and protective measures.(d) Removing of Nails, making good holes, cracks etc.(e) Work in patches and in narrow/width, bands, cornices, pilasters etc and cutting in edge of line where necessary.(f) Spreading and removing covering to doors, windows, floors, fittings etc to protect them from splashes.(g) Washing floors, cleaning glass, joinery, electric fittings, wirings etc. Drops and splashes of paint to be cleaned to the entire satisfaction of Engineer-in-charge.(h) Sample patch of 10 Sqm be prepared considering alll the itmes of periodical and shall be got approved from AGE prior to carrying out further work. |
| 97 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. |
| 98 | S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 making good of dismantled portion by plastered work and match with existing surface complete all as specified and directed. |
| 99 | M&L preparation of old steel and iron surfacesof any description, not otherwise descri-bed, over 10cm width or girth and applying two coat of synthetic enamel paint. |
| 100 | M&L for preparation of new or previously untreated surfaces, of steel and iron work of any description not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of Red oxide all as specified and as directed. |
| 101 | Dismantling loose concrete cover of RCC columns, beams, slabs, chajjas, parapets, railing and the like as directed without disturbing the core of RCC member, roughening and cleaning concrete surfaces with steel wire brushes, washed with and allowed to dry, including application of rust removal cum passivator painted with brush to the rusted reinforcement (and removing rust with flex after 24hours of application of rust remover with the help of wire brush, sand paper) and also applying zinc anti-rust agent as per manufactures method of application to re bar corrosion protection system to reinforcement surface of steel reinforcement with existing reinforcement as directed wherever required binding RCC 100mmx100mm (10 gauge welded mesh) & tack welding after that applying polymer modified cementious bonding coat, prepared and applied on the concrete surface with 1 part of sika latex or equivalent in Forsoc/BASF/Dr Sunanda with 4 part of water and 6 part of cement by weight, coverage of sika latex shall not be more than 0.25 Kg/Sqm for one coat. Adhesive bond strength not less that 2.5 mpa, After this, providing 40mm (average thickness) guiniting mix @ pressure 2.2 to 2.5 kg per sqcm with anti corrosion admixture (using 1 part of ordinary potland cement 43 grade and 2 part of Ghagger sand mixed with adhesive /admixture at the rate as per manufacturer instruction and as directed) including stripping floting with wooden strippers for proper dimension control necessary, formwork and scaffolding, complete surface of guiniting to be finished fair with 10mm thick plaster in cement 1:4 with water proofing compound @ 3% by weight of cement cleaning and removing of waste material etc as directed at site. ( Welded mesh & addl reinforcement if required measured and paid separetly) Note :- Only steel scaffolding is allowed and rate included in above item. The work shall be carried out by enclosing affected area by green cloth) up to Four storey building. |
| 102 | M & L hard drawn steel wire fabric cut to length, bent to shape required of mild steel wire mesh / welded mesh and tying with and including annealed mild steel wire not less than 0.9mm dia binding wire S & F in reinforcement weight not exceeding 4.00 Kg/Sqm complete all as specified and directed |
| 103 | S & F in repairs Exhaust fan louvers 230/300 mm size, iron including taking out old louvers up to fourth floor complete all as specified. |
| 104 | supply only Liquid water proofing compound |
| 105 | S & F in repair Vitreous China wash down water closet pan with seat cover (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe)including sheet cover |
| 106 | S and F PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet,ball valve, float and handle including brackets with 32 mm CP Flush pipe of Low level cistern. |
| 107 | 18/19 mm thick solid WPC board, as in cupboard shutters, partition walls and shelves fixed with frame complete all as specified and directed. |
| 108 | S&F in Repair Kitchen cabinets made out of WPC sheet board 19mm thick including making drawers, partitions, shelves and WPC board on all sides with following specifications and as directed by Engineer-in-charge:-(a) 19mm thick WPC solid flush board with 5mm thick pre-laminated sheet fixed on one side, as kitchen cabinet. (b) Frame of size 50mmx47mm. (c) Shutters having piano hinges and brass handle 75mm long No for each shutter. (d) Bottom back and sides of cabinet covered with 19mm thick WPC board with 5mm thick pre-laminated sheet fixed on one side.(e) Drawers having brass handle 75mm long and two long sliding rails for each drawers with magnatic catcher as required.(f) Cabinet must have one drawers supported of sliding rails. (g) Size of each cabinet shall not be exceeding 0.9 M x 0.75 M and 0.60 M depth. (h) Measurement will be considered only for front face i.e. length & height & depth 0.50m. (j) SS jali racks mounted on drawer chanel Note: Measurement for purpose of payment shall be made on external visible face for width x height (considering frame). |
| 109 | M&L for Supply and fixing 18 mm thick 100 % Solid premium quality Action Tesa HDHMR base board pre laminated both side (of approved colour) having density more than 850 kg/cum, fixed with screws as in wall panel, storage cabinet/Vanities/ Cub board and built in modular tables etc, for hold of shelf / partation and shall provide 3 edges in sizes 18 mm x 18 mm as per required length. the edges of shelf / partation / wall side to be lipped with including 18 mm x 1 mm thick laminated sheet of density 850 kg/cum manufactured by as ISO -9000 certified company , lipping portion should be match with laminated colour, using solvent cement etc. (including all necessary brass hardware fitting i.e Soft closing hydraulic hinges (Make : Atlantic / Lapo/ Hettich) ,handle, ball catchers including mortice locking arrangement (Make: Doorset / Godrej / Yale), hole cap including lipping etc, and Channel siliding rail in each Cup board/ Vanities complete incl dismantling of existing all as specified and directed. |
| 110 | S & F stainless steel soft closing spring hinges at 0 degree hinges (hydraulic type) of approved make - Hettich/Haffele or equivalent in others to cupboard shutters of kitchen cabinets with full threaded steel screws including making necessary recess in board and finished etc. complete as per direction of Engineer-in-charge. |
| 111 | Dismantling brick tiles or terracing tile, single layer on roof including cleaning the roof surface and filling the cracks with silicon compound if obsserved on roof |
| 112 | M&L for PCC 1:2:4 type B-1 (20mm graded aggregate ) 50mm thick as in padding finished even and smooth witout using extra cement |
| 113 | M&L for Applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 Kg per sqm including bitumen primer @ 3.5Kg/Sqm |
| 114 | M&L for Laying APP (atatic polypropylene) modified membrane 3mm thick and weighing not less than 3 kg/sqm with 160 GSM/sqm, non woven polyester mat as center core reinforcement, laid with 75 mm side over lap and 100mm end over lap, the membrane has to be laid with LPG tourch and over lap sealed and finished neat over roof including a coat of bitumen 85/25 at the rate of 1.2 Kg per sqm over APP membrane. |
| 115 | M&L for non skid roof tiles with cooling properties of size 300x300 mm and 8-10 mm thick with solar reflective index (SRI) value upto 98%. Make OreientBell / Somany/ Kajaria Cat Part No. Orient Cool Tiles(EC) Bianco or equivalent including screed bed of 15mm thick cement mortar 1:4 all as specified and directed. |
| 116 | S&F in repair SS night latch with suitable stainless steel chain of size 250 to 300mm long including plate and fixed as in repairs complete all as specified. Make -Godrej. |
| 117 | Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/wall paneling, blankets, any thickness, including cover fillets and frame complete. |
| 118 | S&F Solid PVC Wall Lining consisting of 5mm thick single side prelam PVC sheet (colour as approved by Engr-In-Charge) instead of Plain colour PVC sheet inclusive of PVC frame work, solvent cement, screws, fasteners and all required accessories and fixing the sheet at site on PVC frame as per specifications and drawing including complete all as specified and directed. Make : Rajshri |
| 119 | S&F Charcoal Designer Wall Paneling consisting of 12mm thick embossed Charcoal sheet of approved color and texture, fixed directly onto existing masonry/plywood surfaces using premium high-bond polymer adhesive, masking tapes, headless nails, and matching silicone joint fillers, inclusive of all preparatory surface work, scaffolding, and required accessories at all heights as per drawing, including complete all as specified and directed. |
| 120 | S&F High-Grade PVC Fluted Paneling (Louver Panel) consisting of minimum 10mm to 12mm thick heavy-duty interlocking PVC sheets (12 inch/300mm width, pattern/colour as approved by Engr-In-Charge) featuring distinct 3D vertical grooves, instead of plain flat sheets, inclusive of structural aluminium/PVC framing, high-performance solvent cement, tongue-and-groove interlocking profiles, GI clips, self-tapping screws, fasteners, and all required trim accessories; fixing the panels at site on framework as per technical specifications and engineering drawings, including complete all as specified and directed. Make: Europratik / Vox / Plantex or approved equivalent |
| 121 | S&F (Supply and Fixing) Exterior/Interior Grade Aluminium Composite Panel (ACP) Wall Paneling consisting of minimum 4mm thick panel with a 0.25mm/0.30mm aluminium skin thickness on both sides and a polyethylene (PE) core (colour and finish as approved by the Engineer-in-Charge). System inclusive of an aluminium tube/runner grid framework, high-tensile GI brackets, fast-curing anchor fasteners, masking tapes, flashing, and weather-proof silicone sealant; cutting, routing, folding, and securely fixing panels to the framework using stainless steel rivets/screws at all levels and heights, complete in all respects as per engineering drawings and manufacturer specifications |
| 122 | S&F Fire-Retardant Corrugated ACP Wall Paneling consisting of minimum 4mm thick Class B-s1, d0 / Class A2 Fire-Retardant Aluminium Composite Panel with pre-formed corrugated/3D ribbed profile (colour, texture, and profile configuration as approved by Engr-In-Charge), inclusive of concealed heavy-duty structural aluminium framing system, non-combustible mineral-filled core, approved GI brackets, fast-curing anchor bolts, fire-rated weather silicone sealants, masking tapes, flashing, and trim sections; cutting, routing, folding, and securely fixing panels mechanically to the aluminium grid using stainless steel fasteners at all levels, heights, and elevations as per engineering drawings, including complete all as specified and directed. Make: Aludecor (A2 Grade) / Viva (FR) / Alstrong or approved equivalent |
| 123 | M & L for providing & fixing semi perforated 12 mm thick micro tegular edged GI T-Grid false ceiling tiles of Size 595 x 595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Noncombustible as per BS 476 (part 4 )-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main T runners of size 15 x 32 mm of length 3000mm,cross-T of size 15x 32mm of length 1200mm and secondary intermediate cross-T of size 15 x 32 mm of length 600mm to form grid module of size 600x 600mm , suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1000mm length and L shape level adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size 24x 24x0.40mm of length 3000 mm to be fixed on periphery wall I partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge |
| 124 | M&L12mm thick Gypsum board as in ceiling/lining fixed with counter sunk screws on & including GI channels frame work of standard section as per manufacturers instruction , fixed @ 1.2m in one direction and 45cm in C/C in other direction with necessary fixing arrangement at their junction point at desired heights below roof slab and including two coats of plastic emulsion paint over a coat of primer on exposed surfaces, the frame work shall be fixed with the help of GI suspenders of suitable size with the help dash fasteners and along wall, making good disturbed surfaces smoothening the gypsum board, POP lining at joints panning as required complete all as specified and as directed. |
| 125 | Providing, fixing, and modifying high-pressure plumbing pipelines for a G+10 high-rise building vertical riser network, including isolating, bypassing, or removing accumulated air pockets, Air Release Valves (ARV), or Pressure Reducing Valves (PRV) to convert the network into an uninterrupted direct pressure line as directed; the work includes high-pressure pipe cutting, jointing, fitting bypass loops, and execution at height using heavy-duty steel scaffolding systems, with mandatory deployment of ISI-marked full-body safety harnesses (safety belts) anchored to independent lifelines, helmets, and personal protective equipment (PPE); the quoted unit rate shall deem to include the cost of all skilled labor, scaffolding erection and dismantling, safety supervision, material lifting to upper floors, and pressure testing complete all as directed |
| 126 | Demolition of brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete. |
| 127 | M&L for Brick work with sub-class `B' bricks, straight or curved on plan exceeding 6 M mean radius built in cement mortar (1:6) complete all as specified and directed. |
| 128 | Note :- Removing building materials /old waste unwanted existing material of any description or any type etc. to a distance beyond out side MOD Land. Note :- The work described in these items shall be executed in bldgs up to (G+10 floor) hence the contractor shall make scaffolding arrangements, trestles, ladders etc and hessian clothes for protection & all other safety precautions up to 04 storeys of buildings and the cost for the same is deemed to be included in the quoted unit rates. Please Enable Macros to View BoQ information |
| 129 | Note :- Removing building materials /old waste unwanted existing material of any description or any type etc. to a distance beyond out side MOD Land. Note :- The work described in these items shall be executed in bldgs up to (G+10 floor) hence the contractor shall make scaffolding arrangements, trestles, ladders etc and hessian clothes for protection & all other safety precautions up to 04 storeys of buildings and the cost for the same is deemed to be included in the quoted unit rates. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 30, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 27, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 12 daysSep 01, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 17 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender