Tender For 8561/E8 : Repair & Maintenance Of Swimming Pool Installation, Replacement Of Parts & Allied Wks Under Ge (East) Bareilly
Tender Value
24.98 Lakhs
Estimated cost
Bid Submission
20 Aug 2026
19 days left
EMD
49900
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Bareilly → Uttar Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for 8561/E8 : Repair & Maintenance Of Swimming Pool Installation, Replacement Of Parts & Allied Wks Under Ge (East) Bareilly
BOQ
| Sl. No. | Item Description |
| 1 | Lifting/taking out defective submersible pump of any capacity alongwith column pipe of any size and submersible cable, dismantling the pump from motor, setting aside for repair /servicing / overhauling including lowering the pump set into borewell replacement of packing and nut bolts (if required) and testing after the completion of repair works in the presence of JE/ Engr in charge . |
| 2 | Disconnections of electric connection of the starter of 3/5/12.5/15/25 HP Pumping set for repairs installed at LT Panel in the pump house, carefully checking the parts throughly & replacement of unseviceable parts such as electronic Motor Protection relay with inbuilt earth fault protection, Over load protection relay ranging 16 -100Amp, MNX-16-100 contractor, NO-NC for starter, (Front add on auxilary contact block) and electronic timers multi time setting type, 240/415 Volt, 50 Hz of range, complete all as specified & directed. Make- L &T / Havells/Minilec. Note :- Spare parts to be measured and paid seperately in respective items. |
| 3 | Dismantling the submersible pump assembly capacity 12.5/15 HP completely, checking and segregating serviceable / unserviceable parts, cleaning serviceable parts thoroughly by approved method, replacement of wron out parts, stage casing, pump shaft, impeller, key, bearings , bowl bush NRV, nut, bolts and other minor parts etc including necessary lath / machinery work including all new parts as reqd, re-assembling the pump completely lowering the pump alongwith all accessories to the existing location, overhauling, commissioning, testing and connecting up complete including painting all as specified and directed. |
| 4 | Dismantling, cutting and removing the burnt windings from the submersible motor of capacity 12.5/15 HP, rewinding with suitable size / gauge of super enameled / copper conductor and other approved insulating materials, heating, drying and replacement of existing size of submersible cable including varnishing, overhauling, reassembling the motor, installing, commissioning, testing and connecting up complete all as specified and directed. |
| 5 | Supply only of following parts suitable for ser item No 05.00 for Submersible motor :- |
| 6 | (a) Oil Seal Set |
| 7 | (b) `O` ring set |
| 8 | (c) Motor bearing Bush set |
| 9 | (d) Complete Pad set (Bearing assembly) |
| 10 | (e) Rotor sleeve set |
| 11 | (f) Thrust plate with ferredo lining |
| 12 | (g) Upper/Lower bearing house |
| 13 | (h) Balancing ring |
| 14 | Dismantling the submersible pump assembly capacity 3.0/5.0 HP completely, checking and segregating serviceable / unserviceable parts, cleaning serviceable parts thoroughly by approved method, replacement of wron out parts stage casing, pump shaft, impeller, key, bearings , bowl bush NRV, nut, bolts and other minor parts including necessary lath / machinery work including all new parts as reqd, re-assembling the pump completely lowering the pump alongwith all accessories to the existing location, overhauling, commissioning, testing and connecting up complete including painting all as specified and directed. |
| 15 | Dismantling, cutting and removing the burnt windings from the submersible motor of capacity 3/5.0 HP, rewinding with suitable size / gauge of super enameled / copper conductor and other approved insulating materials, heating, drying and replacement of Seal, O ring, bearing, bush thrust plate, etc existing size of submersible cable including varnishing, overhauling, reassembling the motor, installing, commissioning, testing and connecting up complete all as specified and directed. |
| 16 | Disconnections of electric connection of centrifugal pump and motor capacity of 25/20 HP, lifting and removing motor form its existing foundation to the location (in side/outside of building) where directed by the Engr-in-charge. Dismantling the pump and motor of capacity 25/20 HP, carefully checking, segregating serviceable and unserviceable parts, cleaning the serviceable parts thoroughly by approved method (Pats like stator, rotor, terminal box, bearings shaft, key etc) heating, drying & varnishing including replacement of burnt winding for 25/20 HP motor with super enameled copper wire of existing gauge and good quality of insulating materials including replacement of unserviceable parts as required including necessary lath / machining work. Reassembling the pump and motor including painting with two coats of synthetic enamel paint after necessary surface preparation, marking of number (SM, MES or srl No) installing to its existing foundation, commissioning, connecting up and testing complete as directed.Note:- Spares shall be measurded and paid separately under respective items. |
| 17 | Disconnections of electric connection of centrifugal pump and motor capacity of 12.5 HP, lifting and removing motor form its existing foundation to the location (in side/outside of building) where directed by the Engr-in-charge. Dismantling the pump and motor of capacity 12.5 HP, carefully checking, segregating serviceable and unserviceable parts, cleaning the serviceable parts thoroughly by approved method (Pats like stator, rotor, terminal box, bearings shaft, key etc) heating, drying & varnishing including replacement of burnt winding for 12.5 HP motor with super enameled copper wire of existing gauge and good quality of insulating materials including replacement of unserviceable parts as required including necessary lath / machining work. Reassembling the pump and motor including painting with two coats of synthetic enamel paint after necessary surface preparation, marking of number (SM, MES or srl No) installing to its existing foundation, commissioning, connecting up and testing complete as directed.Note:- Spares shall be measurded and paid separately under respective items. |
| 18 | Supply only of following parts suitable for ser item No 10.00 for centrifugal pump and motor. |
| 19 | (a) 25/20/12.5 HP Pump Bearing No 6310 or suitable size |
| 20 | (b) Pump bearing seat suitable for 3 ph 25/20/12.5 HP motor |
| 21 | (c) Motor side cover suitable for 3 ph 25/20/12.5 HP motor |
| 22 | (d) Motor connected plate six hole suitable for 3 ph 25/20/12.5 HP motor |
| 23 | (e) 25/20/12.5HP Motor Bearing No 6308 or suitable size |
| 24 | (f) 25/20/12.5 HP Motor Bearing No 6309 or suitable size |
| 25 | (g) 25/20 HP impeller |
| 26 | M&L for Dismantling Non Clogging pump set up to 5 HP, carefully checking, segregating serviceable and unserviceable parts, cleaning the serviceable parts thoroughly & including replacement of unserviceable parts as required (Block piston, Nozzle, head block, cupling engine parts & Impeller, gland packing, Pump shaft, pump seal Pump parts) including necessary lath / machining work. Reassembling the pump and engine parts including painting with two coats of synthetic enamel paint after necessary surface preparation, marking of number (SM, MES or srl No) & replacement of unserviceable suction & Delivery PVC pipe, flange, clamps, foot valve etc and testing complete as directed. |
| 27 | Supply and fixing DI fittings for Flanged pipe, DI Bends, connecting pieces, bell mouth pieces, tapers, tee pieces of one end flanged and other end spigot or socket upto 150 mm bore complete all as specified and directed. |
| 28 | M & L for construction of brick masonry valve pit of size 90x90x90cm (internal dimension) one brick thick wall built in CM (1:4) on 100mm thick PCC (1:4:8) type D2 (using 40mm graded crushed stone aggregate) as in foundation, and 15mm thick rendering in cement mortar (1:4) both externally and internally, external plaster shall be up to 15cm below GL, providing valve pit cover made of 3.15mm thick MS sheet/plate, including provision of hinges, handle and locking arrangement including 40 X 40 X 5mm angle iron frame fixed on top of valve pit by means of MS hold fast 40x5mm and 150mm long, embedded in PCC (1:2:4) type B-1 (using 20mm graded stone aggregate) including two coats of anti-corrosive paint over a coat of red oxide zinc Chrome primer and necessary earth work in soft/loose soil including demolition of old unserviceable existing valve pit & pit cover complete all as specified & directed. |
| 29 | S&F CI Non Return Sluice Valve flanged ends of class 1.6 PN, size 150mm bore including taking down old existing unserviceable Non Return Valve complete all as specified and directed. |
| 30 | S&F CI Non Return Sluice Valve flanged ends of class 1.6 PN, size 100mm bore including taking down old existing unserviceable Non Return Valve complete all as specified and directed. |
| 31 | M&L for repairs to leaking joints for CI/DI pipe, spigot and socket pipes and fittings, of following sizes of bore in water mains, by burning out old lead joints in position including provision of run lead and including necessary excavation and earht work complete all as specified and directed. |
| 32 | (a) Bore of pipe 150 mm |
| 33 | (b) Bore of pipe 100 mm |
| 34 | (c) Bore of pipe 80 mm |
| 35 | Supply,installation,Commissioning and testing of Smart Motor Protection (electronic smart relay for metering and protection with VFD) controller having feature as Protection against UV,OV, Phase loss, Phase unbalanced,Phase asymetery & auto phase polarity correction with time delay & having display of V, I, Of, Hz with iOT enabled and potential free feedback contacts suitable for 25 hp motor-3 phase induction motor with following details. |
| 36 | (i) E300 overload relay (193/592 IEC/Nema) group selection (ii) 2 IN / 2 Out control Module. 240V AC (iii) V/I/GF Sensing Module (.5-30A) DIN rail/ Panel Mount Power Terminals. (iv) Voltage/current/ Ground fault sensing module (1C…100A) DIN Rail/ Panel Mount with line and Load side power conductor Terminals. (v) Voltage/ Current/ Ground fault sensing module (20..200A) DIn Rail/ panel Mount with line and load side Power conductor Terminals |
| 37 | ,-ditto- all as per item ser No. 18 here-in-before but suitable for 15/10 HP Submersible pump set |
| 38 | Supply and fix Green & Red button operated push type, Fully automatic Star Delta Starter with Single Phase Preventer, Type designation BSA, Operatig current 18-25Amp, voltage 380 _+15% , 3 phase 415V 50 Hz suibtable for 12.5/15 HP Submersible Pump and Motor complete with Over load tripping circuit (Max relay (14-20 Amp), Reverse phasing , unbalancing, Low voltage , high voltage upto motor terminal and starting time delay and should be housed in Dust proof, Moisture proof and powder coated sheet metal fabricated box with locking arrengement with extra long life contact with arrengement including taking down of existing starter complete all as specified and directed . Make- Kapil SKN or equivalent |
| 39 | Supply and fix DOL starter three phase 415 volt 50 Hz push button type suitable for 05/7.5 HP centrifugal pump set with arrangement and making the necessary connection in panel and pump set including taking down of existing starter complete all as specified and directed. Make- L&T or equivelent as approved by GE |
| 40 | M&L for Painting to pipe of Swimming pool plant /pump house rising mains, header, valves, pipe, fittings, NRV, discharge head etc after cleaning, scrapping and making the surfaces free from rust of main externally and painting with two coats synthetic enamelled paint in black / blue / red including marking / writing on pipe etc complete as specified and directed |
| 41 | Supply and fix in replacement Pool inlet surflow Nozzle made of Stainless steel 40/50mm dia. for uniformly spreading of water along the pool floor/wall |
| 42 | M&L for providing technician for attending any breakdown of swimming pool equipment and machinery as per requirement and directed by Engr-in-charge for fixing the issue on site and making the plant functional including repair and replacement of minor parts of starter, motor, plant etc |
| 43 | M&L for trimming vegetation or small inequalities clearing all grass vegetation, saplings, shrubs, brushwood, roots, and tree of surroundings area up to 500 sq mtr including cleaning and removing rubbish upto a distance of 50 mtr outside the periphery of the area under clearance of water supply installations complete all as specified and as directed. |
| 44 | M&L for providing and lowering, connecting submersible pump set 5 to 15 HP during the unserviceability of existing pump set including connecting pipe cable etc as per site requirement |
| 45 | Supply & fix in repair 1100 volts grade heavy duty cable PVC insulated aluminum conductor screened served with inner sheathing of PVC tape and over all PVC sheathed in service connections suspended by insulating hangers not more than 1 meter apart including 4mm GI suspension wire, one twin core cables flat or circular of size 10 Sqmm etc complete all as specified and directed. |
| 46 | S&F in repair Off load change over switch 400 Amp, 4 pole, 415 Volts, 50 Hz, with enclosure complete all as specified and directed |
| 47 | M&L for Earthing complete with using GI earth plate electrode 600x600x6.0 mm thick burried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 mtr below normal ground level and earth plate surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness off 15 cm all around the plate with using GI Strip 25 x 4mm as earth lead moulded and retreived to earth plate at one end and connected to main switch / control board at another end with and including 15 mm dia GI light grade from upper end of earth plate upto external face of the wall of the building including 20 mm dia bore GI pipe light grade as water pipe from chamber to upper edge of the plate GI funnel with wire mess fixed on water pipe and provison of PCC 1:2:4 type B-1 (Using 20 mm Dia graded stone aggregate) duly reinforced with mild steel round bar 6 mm dia @ 150 mm c/c both ways with 10 mm dia mild steel bars as in lifting handle with and including necessarry excavation and earth work including laying the pipe concealed in floor / wall allas per plate NO-3 of SSR Part-I complete all as specified and directed and testing on completiopn (Note:- If the desired resistance is not found earthing shall be done by the contractor at no extra cost to Govt). |
| 48 | M & L for Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 25 x 4mm galvanised iron strip, complete all as specified and as directed. |
| 49 | Supply and Fixing of suction strainer for 25HP pump set of size 200mm all as specified and directed. |
| 50 | S & F in repairs of MCB TPN DB 4 Way, (4+12) suitable for flush mounting and surface mounting, conforming to IP 43 - IK 09 with acrylic door with 100 Amp copper bus bar for each phase, complete with din rail, Neutral and Earthing bar after taking out the old unserviceable DBs, connection complete and making good the disturbed surfaces complete all as specified and as directed. |
| 51 | S & F in repairs of DX3 AC MCB SP, 240 Volt, 6 to 32 Amp, 10 KA, ISI Marked, \\"C\\" Curve, IP 20 Protected terminals, Complete all as specified and as directed. |
| 52 | S & F in repairs of DX3 AC MCB TPN, 415 Volt, upto 63 Amp, 10 KA, ISI Marked, \\"C\\" Curve, IP 20 Protected terminals, Complete all as specified and as directed. |
| 53 | Supply only Calcium based granularhypo chlorite 65% to 70% disinfectant for water treatment, Packing in 45 Kg, plastic drums complete all as specified and directed. |
| 54 | M&L MCCB 4 pole, 415 Volt, fixed type 125 to 160 amp with breaking capacity 25 Ka complete all as specified and directed. |
| 55 | M&L MCCB 4 pole, 415 Volt, fixed type 160 to 200 amp with breaking capacity 25 kA complete all as specified and directed. |
| 56 | M&L MCCB 3 pole, 415 Volt, fixed type 63 to 100 amp with breaking capacity 16 Ka complete all as specified and directed. |
| 57 | Supply and fixing in repairs PVC pressure hose pipe upto 10 to 20Kg/cm2 as per existing size, complete all as specified and directed. |
| 58 | S&F in repairs Digital multi programmable electronic timer capacity for 24 hrs clock, 3 phase, 415 volts, 50 Hz, complete all as specified and as directed. |
| 59 | S&F in repairs electronic Single phase preventer operation on 415 volts 50 Hz all as specified and as directed. |
| 60 | S&F in repairs three phase digital type voltmeter accuracy class 1.0 flush mounting 96x96 mm inbuilt selector switch input voltage measurement range 17-520 VAC all as specified and as directed. |
| 61 | S&F in repairs three phase digital type Ammeter accuracy class 1.0 , 5A flush mounting 96x96 mm inbuilt selector of range 0-300 amp CT/PT site programmable all as specified and directed. |
| 62 | M & L for Grass and weeds killer chemical 5 Ltrs capacity of make Roundup, complete all as specified and directed. |
| 63 | S&F LT rubber mat of size 1.0mx2.0mx2 mm at water supply installations, complete as specified and directed. |
| 64 | S&F pressure gauge of dial 0 to 14Kg/cm2, suitable for fixing at MS pipe 100/150/200 dia header with all fiting and fixtures etc, complete as specified and directed. |
| 65 | S&F Over load protection relay suitable for 5HP to 25HP monoblock/centrifugal /submersible motors of make L&T all as specified and directed. |
| 66 | Supply and fix in repair MNX contactor 16Amps to 40Amps, 3 Pole with NO and NC complete all as specified and directed. Make : L & T. |
| 67 | S&F in replacement MS ERW column pipe screwed 100 mm nominal bore having wall thickness not less than 7.11 mm electric resistance welded with MS flanged 16 mm thick heavy duty confirming to IS 6392 incl 2 mm thick rubber sheet and steel nuts and bolts 10 mm long with washer etc, complete as specified and directed. |
| 68 | (a) 150 mm nominal bore. |
| 69 | (b) 200 mm nominal bore. |
| 70 | (c) 300 mm nominal bore. |
| 71 | Take the water sample from the bore well at PH No.38 (Stn swimming pool) & JRC Swimming pool and send it for physical / Chemical / Bateriological test from any recognised govt agency and provide its report to Engr in charge. |
| 72 | S& F in replacement submersible pump/motor 1HP, Electric driven, 415 Volts, TP suitable for bore well, Output dia- 25 mm, Head 60 Mtr, 100 LPM, Vertical type, complete all as specified and directed.Make:-CRI / KSB / KIRLOSKAR |
| 73 | S& F in replacement submersible pump/motor 5 HP, Electric driven, 415 Volts, TP suitable for Well/ Semi UG Sump, Head 70-90Mtr, 750 LPM, Vertical type, complete all as specified and directed.Make:-CRI / KSB / KIRLOSKAR |
| 74 | S& F in replacement Monoblock self priming HI-Flow pump/motor 02 HP, Electric driven, 230 Volts , SP suitable for 25/20mm dia output, Head 70-90 Mtr, 120-150 LPM, complete fitting/fixtures with starter panel, complete all as specified and directed. Make:- CRI, KSB and KIRLOSKAR. |
| 75 | Supply fixing testing and commissioning submersible cable flat 10.0 sqmm x 3 core PVC insulated and PVC sheathed with multi stranded copper conductor 1100 volts grade fixed to submersible motor column pipe using suitable size of clamps made out of stainless steel flat of size 20x2 mm with steel nuts bolts & washer foe every column pipe of 3 mtr lenght all as specified and directed. |
| 76 | (a) 6.0 sqmm x 3 core.. |
| 77 | (b) 4.0 sqmm x 3 core.. |
| 78 | (c) 2.5 sqmm x 3 core.. |
| 79 | Supply, installation, Commisioning and testing for Chemical dosing system metering type, capacity to deliver 14- 27 LPH max & adjustable from 10% to 100% through Knob and suitable to inject against 5-10Kg/cm2 pressure duly operated by 240V, Single phase power supply, Chemical Solution preparation tank of 200 Ltrs capacity made out of FRP (made with Bisphenol resins) having port hole on lid for pouring chemical, water inlet connection, overflow and drain with valve, outlet connection with PP ball valve for transferring solution to chemical dosing tank of 100 Ltrs capacity made out of FRP (made with Bisphenol resins) having port hole on lid, inlet connection and tank lid duly mounted with agitator made of Stainless Steel -316 operated with single phase FHP electric motor for dissolution of chemical, dising pump shall be complete with inlet /outlet check valves, strainer cum foot valve and tubing for suction/delivery injection line including fittings etc, complete all as specified and as directed Make : Declibac Modle :-96 NGQ51, Item NR:- DPP9651 or Equivalent in poter & Watt Crop/Briozing Unlimited. |
| 80 | Supplying, installing, commissioning & testing of cast iron body butterfly valves of size 200 mm capacity 10 Bar and PN.1.0 rating and per BIS 13095:1991 with fresh rubber gaskets , bolts and nuts Butterfly vlaves all as specified and directed. |
| 81 | Supplying, installing, commissioning & testing of cast iron body butterfly valves of size 100 mm capacity 10 Bar and PN 1.0 rating and per BIS 13095:1991 with fresh rubber gaskets, bolts and nuts Butterfly vlaves all as specified and directed. |
| 82 | Repair/Maintenance of Swimming Pool and other allied worksM&L for complete overhauling and repairing of pressure filter capacity 280 Cu M/hr including removal of chocked media from filter and depositing same with 30 m from plant room, scraping and cleaning of filter inside surfaces and re-painting with 3 black bituminous pant, cleaning of lateral pipes and recharging each filter with fresh filter media as follow :- i. Natural graded gravel of size 25mm - 20 mm : 150 mm layer: 68 Cu Ftii. Natural graded gravel of size 15mm - 10 mm : 100 mm layer: 45 Cu Ftiii. Natural graded gravel of size 10 mm - 6 mm : 100 mm layer: 45 Cu Ftiv. White graded coarse quartz sand 8 + 14 mesh : 100 mm layer: 45 Cu Ftv. White graded coarse quartz sand 16 + 30 mesh: 600 mm layer: 22 Cu Ftvi. Cleaning and repairing of under wash system including renewal of broken/defective unserviceable strainer/nozles. vii. Replacement of man holes & hand holes gaskets, painting exterior surface with synthetic enamel of approved shadesviii. Scraping cleaning / making internal and external shell of filteration plant neat and tidy and painting internal surfaces with two coats of anti corrosive black bituminous lead free paint over a coat of primer and externally with two coats of synthetic enamel paint over one coat of primer with sprayers and wiritng description of filteration plant complete all as specified and directed. |
| 83 | M&L for soda ash as directed by Engr in Charge |
| 84 | M&L for Bleaching powder as directed by Engr in Charge |
| 85 | M&L for copper sulphate as directed by Engr in Charge |
| 86 | M&L for Alum Crystal as directed by Engr in Charge |
| 87 | M&L for dismantling of non clog type centrifugal pumping set of capacity 5/7.5 HP either fixed on floor or on trolley mounted and taking out unserviceable spares and performing following operation to complete the task :-(a) rewinding of motor centrifugal pumping set with insulated copper winding wire including sleeves as per original company and replacement of worn out parts, including grinding & polishing of rotor sleeves and refixing, testing & transport charges complete all as specified & directed. (b) replacement of motor bearing with lock nut -02 Nos. (c) replacement of fan motor-01 No. (d) replacement of star couling set with rubber -01 each. (f) replacement of impellor with key -01 No (g) replacement of gland coupling -01 No |
| 88 | De watering of well up to 26' feet deep and up to 8 mtr dia by portable pumping set and taking out manually waste material like sludge,mud,soil,sanitory material and other dirts etc from inner sump and outer housing sump by using labour/equipment and depositing the same waste material at low lying area by digging pits all as, Cleaning and washing the surface area of sump well with wire brush and removing the algae growth including removal of grass/tree roots inside sump and above surrounding area etc all as specified and directed . |
| 89 | S&F in repair sluice valve class PN-1.6 heavy duty flanged ends drilled ISI marked confirming to IS: 14846 suitable for 150 mm bore pipe, wheel operated (Handle) with high tensile stainless steel spindle, including nuts, bolts and jointing with jointing materials etc. complete including taking out old existing unservicable sluice valve including making arrangement for safe working all as specified and directed. Make: BIR, KIRLOSKAR, Kartar |
| 90 | S&F in repair sluice valve class PN-1.6 heavy duty flanged ends drilled ISI marked confirming to IS: 14846 suitable for 100 mm bore pipe, wheel operated (Handle) with high tensile stainless steel spindle, including nuts, bolts and jointing with jointing materials etc. complete including taking out old existing unservicable sluice valve including making arrangement for safe working all as specified and directed. Make: BIR, KIRLOSKAR, Kartar |
| 91 | Supply & Replacement suction sweeper , head 24 to 36mtr long with trolly mounted type including suitable pump, suction/delivery hose of suitable size , Brush and connected items complete all as specified and as directed & after dismantling the unserviceable one. |
| 92 | S&F foot valve of size 150/200 mm bore complete all as specified & directed |
| 93 | S&F foot valve of size 80 mmbore complete all as specified & directed |
| 94 | S& F Chlorine test kit of standard size for to check daily Chlorine as directed |
| 95 | Supply only O-Tolodine regent solution in 500 ml bottle as per Sample approved complete all as specified and directed. |
| 96 | M&L for cleaning the swimming pool by draining out the water and removing the debris and cleaning the wall and surface of swimming pool by scrapping using tile cleaning brush, pool safe chemical to remove stains from from wall and floor or hight pressure washer to scrub the wall and floor and draining out the water using suction sweper or vaccum cleaner heavy duty , and finally rinsing the surface with clean water using pressure washer and draining out the water and debris all as directed by Engr-in-charge |
| 97 | Suction sweeper comprising of 600 mm long CI fabricated suction head with PVC wheels, spring loaded brush and rubber squeezers including movable trolleymounted with electric driven non clog self priming type centrifugal pump and not less than 2 HP TEFC motor, 3 phase 440 votls electric driven DOL push buttonstarter, 30m long 40mm dia PVC flexible hosepipe, 4 Nos.PVC floats and 50m long rope including 2 Nos. spare brushes complete all as specified and directed. Make:CHLOROMAX / ION EXCHANGE |
| 98 | M&L development of borewell by flushing of borewell complete by using 250 CMF compressor and heavy duty driller machine to deliver the high air pressure at the bottom of the bore well and cleaing/flushing the bore well till the water is become free from any mud and clear complete as per site requirement and all as specified and directed by Engineer-in-charge |
| 99 | Supply and fixing all in one solar LED street light IP66 with high efficiency mono crystaline solar panel PV module not less than 12V, 20W lithium ferro phosphate battery with in-built BMS technology, capacity 12.8V, 10.5 Ah high efficiency LED 100LM/W, MPPT solar charge controller and aluminium extruded body & is specially programmed to automatically control the dimming and brightness of light, which increase the backup time and minimum 10 Hrs backup. |
| 100 | Supply and fix 35 W new generation, IP 65 LED post-top family, energy saving, environmental friendly, long life aestheticallydesigned with symmetrical light distribution, spun aluminium landscape luminaire with high power LEDs as light source. clear cover offers bright illumination for different applications. |
| 101 | S&F swimming pool skimmer net , heavy duty swimming pool leaf rake with deep fine nylon mesh net bag with stainless steel bristles hogard telescopic pole extendable upto 20 Feet |
| 102 | Supply and fixing in replacement of PVC suction currugated hose pipe with flanged ends of green colour of bearing capacity 2500 Pa, temperature range 0deg-100deg and velocity 30-40 m/s of foloowing size all as specified and directed by Engr-in-Charge. |
| 103 | (a) 40 mm bore |
| 104 | (b) 50 mm bore |
| 105 | (c) 80 mm bore Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 30, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 20, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 19 daysAug 27, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 26 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender