Tender For Construction Of 12 Nos. Type- Ii Quarter (2 Nos. Block) For Women Police Station At Dharamshala, Distt. Kangra H.P.(Sh:-Construction Of 6 Nos. Type- Ii Quarter ( Block-A), Building Portion Including Water Supply & Sanitary Installation, Ra
Tender Value
2.08 Crore
Estimated cost
Bid Submission
05 Aug 2026
5 days left
EMD
4.16 Lakhs
Bank guarantee accepted
Document Fee
5000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Kangra → Himachal Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of 12 Nos. Type- Ii Quarter (2 Nos. Block) For Women Police Station At Dharamshala, Distt. Kangra H.P.(Sh:-Construction Of 6 Nos. Type- Ii Quarter ( Block-A), Building Portion Including Water Supply & Sanitary Installation, Rain Water Harvesting System And Site Development
BOQ
| Sl. No. | Item Description |
| 1 | Excavation in foundation, trenches etc. in earth work in all classification of soil such as pick work, jumper work, pick jumper work, blasting work, jumper blasting work, soft and hard blasting and saturated soil, de-watering, including wedging out rocks where blasting work is prohibited, chiseling or any other mixed variety of soil, including shoring, shuttering and pumping out water upto any depth or any quontam of water including slush which may be arise during de-watering removal of slush and stacking the serviceable and un-serviceable material clear from the edge of excavation as direction of Engineer-In-Charge and retuning the stacked soil in 15cm (Fifteen centimeter) layers, when required into plinths, sides of foundation etc; consolidating each deposited layer by ramming, watering and then disposing of all excavated earth as directed by the Engineer-in-Charge, including carriage of material ,within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rates inclusive of octori, royality, Malkhana, toll taxes, GST and any other taxes imposed by the Government. |
| 2 | Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in Foundation footings, bases of columns and mass concrete , including carriage of material including carriage of material within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 3 | Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in flat surfaces such as soffits of suspended floors roofs, landings as per Architectural drawing and the like , including carriage of material within all leads, lifts of materials and other incidentals , as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 4 | Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in beams cantilevers girders and lintels sides and soffits of beams, beam haunchings, cantilevers, bressumers and lintels upto all depths/heights including carriage of material ,within all leads, lifts of materials and other incidentals ,as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 5 | Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in plan concrete work in window sill, cornice and moulding etcetera, including carriage of material , within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 6 | Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in columns pillar posts and struts Square, rectangular or polygonal in plan including carriage of material ,within all leads, lifts of materials and other incidentals ,as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 7 | Providing form work with steel plates of 3.15mm (Three decimal fifteen millimetres) thick, welded with angle iron in frames of 30x30x5mm(Thirty into Thirty into Five millimetres),so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights and removal of the same for in-situ reinforced concrete and plain concrete work in stairs cases with slopping or stepped soffits, excluding, landing, including carriage of material ,within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 8 | Providing form work with steel plates of 3.15mm (Three decimal fifteen millimetres) thick, welded with angle iron in frames of 30x30x5mm(Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights and removal of the same for in-situ reinforced concrete and plain concrete work in edges of slabs and breaks in floors and walls under any thickness including carriage of material , within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 9 | Providing form work with steel plates of 3.15mm (Three decimal one five millimeters) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimeters), so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in vertical surfaces such as walls (any thickness) partitions and the like including attached pillasters, buttresses plinth and string courses and the like, including carriage of material , within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 10 | Providing and laying cement concrete 1:4:8 (One cement isto Four sand isto Eight graded broken/crushed stone aggregate 40mm (Forty milimetres ) nominal size and down gauge) mechanically mixed and curing complete excluding cost of forms work in foundation and plinth including carriage of material ,within all leads, lifts of materials and other incidentals as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 11 | Providing and laying cement concrete 1:6:12 (One cement isto Six sand isto Twelve graded broken/crushed stone aggregate 40mm (Forty millimeters) nominal size and down gauge) mechanically mixed and curing complete excluding cost of forms work in foundation and plinth including carriage of material , within all leads, lifts of materials and other incidentals as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 12 | Stone filling in plinth with approved quality under floor including watering, ramming, consolidating and dressing complete including carriage of material within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 13 | Providing and laying in position machine batched and machine mixed cement concrete work of grade M-25 ( M- twenty five) design mix to obtain the compressive strength of 25N/mm 2 (twenty five newton per Square millimetre) for reinforced cement concrete work with cement content not less than @ 360 kg/cum. ( three hundred sixty kilogram per cubic metre) or as per approved design mix for all work upto plinth level to give a smooth surfaces mechnically mixed and vibrated including curing complete and pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability for reinforcement concrete work ( foundation and footing) including carriage of material , within all leads, lifts of materials and other incidentals as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 14 | Providing and laying in position machine batched and machine mixed cement concrete work of grade M-25 ( M- twenty five ) design mix to obtain the compressive strength of 25N/mm 2 (twenty five newton per Square milimetre ) for reinforced cement concrete work with cement contents not less than @ 360 kg/cum. ( three hundred sixty kilogram per cubic metre) and as per approved design mix for all work above plinth level to give a smooth surfaces mechanically mixed and vibrated including curing complete and pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability for reinforcement concrete work including carriage of material , within all leads, lifts of materials and other incidentals as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 15 | Coursed rubble masonry/polygonal rubble masonry (uncoursed/brought to courses) with hard stones of approved quality in foundation and plinth at plinth level in Cement Mortar 1:6 (one cement isto six sand) including entire carriage of materials within all leads, lifts of materials and other incidentals as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 16 | Providing Tor steel reinforcement Thermo -Mechanically Treated Bars of grade FE- 500 D (five hundred) or more of Sail / Tisco /Tata for reinforced cement concrete work including bending, binding, straighting, cutting and placing in position complete including cost of binding wires complete for all floor including carriage of materials , within all leads, lifts of materials and other incidentals as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 17 | Providing Tor steel reinforcement Thermo -Mechanically Treated Bars of grade FE- 500 D (five hundred) or more of Sail / Tisco /Tata for reinforced cement concrete work including bending, binding, straighting, cutting and placing in position complete including cost of binding wires complete for all floor including carriage of materials , within all leads, lifts of materials and other incidentals as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 18 | Providing & applying a coat of residual petroleum bitumen of grade VG-10 (viscosity grade - ten) of approved quality using 1.7kg (one decimal seven kilogram ) per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil, including carriage of material ,within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 19 | Second class half brick work using common burnt clay building bricks in super-structure upto all floor level in cement mortar 1:4 (one cement :four sand) curing complete including carriage of material ,within all leads, lifts of materials and other incidentals, as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 20 | Second class brick work using common burnt clay building bricks in super-structure upto all floor level in cement mortar 1:6 (One cement isto Six sand) and curing complete, including carriage of material ,within all leads, lifts of materials and other incidentals, as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 21 | filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15 (fifteen) including carriage of material ,within all leads, lifts of materials and other incidentals ,as per approved drawing, design, specification and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 22 | Providing and fixing aluminium shutter work Jindal/ Hindalco for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15 (fifteen) including carriage of material ,within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 23 | Providing and fixing fly proof stainless steel ( Grade 304) wire gauge of 0.5mm ( zero decimal five milimetres) diametres wire and 1.4mm ( one decimal four milimetres) aperture on both sides in existing Aluminiun shutters on both sides complete including carriage of material within all leads, lifts of materials and other incidentals as per approved drawing, design ,specification and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 24 | Providing and fixing 8 mm (Eight milimetre) anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15)9 fifteen) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm ( two hundred milimetre) centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in- charge. (Only weight of grill to be measured for payment).complete including carriage of material within all leads, lifts of materials and other incidentals as per approved drawing, design , specification and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 25 | Providing and fixing factory made PVC door frame single rebate of RAJSHRI any clours of size 50x47mm ( fifty into forty seven milimetres) with a wall thickness of 5mm ( five milimetres) made out of extruded 5mm( five milimetres) rigid PVC foam sheet heat bend & mitred at corners and jointed with 2 Nos. ( two numbers) of 150mm ( one hundred fifty milimetres) long brackets of 15mmx15mm ( fifteen into fifteen milimetres) M.S. square tube, the vertical door profiles to be reinforced with 19mmx19mm ( nineteen into nineteen milimetres) M.S. square tube of 19 ( nineteen) gauge EPDM rubber gasket weather seal to be provided throughout the frame i/c fixing of door frame to wall with M.S. screws 100long with wooden or rawl plugs emedded in masonry complete as per approved shade including carriage of material , within all leads, lifts of materials and other incidentals as per approved drawing, design ,specification and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 26 | Providing and fixing to existing door frames, 30mm (Thirty millimetres) thick factory made PVC panelled door shutter of RAJSHRI (Code No9-120) consisting of frame made out of M.S. tubes of 19 (Nineteen) gauge thickness and size of 19mm x19mm (Nineteen into nineteen millimetres) for styles and 15mmx15mm (Fifteen into fifteen millimetres) for top & bottom rails, code 9.120 of Rajshri M.S. frame shall have a coat of steel primers of approved make and manufacture M.S. frame covered with 5mm (Five millimetres) thick heat moulded PVC \\"C\\" channel of size 30mm (Thirty millimetres) thickness, 70mm (Seventy millimetres) width out of which 50mm (Fifty millimetres) shall be flat and 20mm (Twenty millimetres) shall be tappred in 45 (Forty five ) degree angle on either side forming style and 5mm (Five millimetres) thick, 95mm (Ninety five millimetres) wide, PVC sheet out of which 75mm (Seventy five millimetres) shall be flat and 20mm (Twenty millimetres) shall be tapered in 45 (Forty five) degree on the inner side to form top and bottom rail and 115mm (One hundred fifteen) wide PVC sheet out of which 75mm (Seventy five millimetres) shall be flat and 20mm (Twenty millimetres) shall be tapered on both side to form lock rail, top, bottom and lock rail shall be provided either side of the panel 10mm (Ten millimetres) thick, 20mm (Twenty millimetres) wide cross PVC sheet be provided as gap insert for top rail and bottom rail paneling of 5mm thick both side PVC Sheet to be fitted in the M.S. frame welded/sealed to the style & rails, joints mitred and jointed with solvent cement adhesive i/c fixing of PVC shutter with existing frame with M.S. butt hinges 100x50x1.90mm ( One hundred into fifty into one decimal ninety millimetres) size with necessary screws etc complete as directed by the Engineer-in-Charge. including carriage of material ,within all leads, lifts of materials and other incidentals as per approved drawing, design ,specification and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 27 | Providing and fixing 12mm (Twelve millimetre) thick Phenol Bonded (Both Sides) Prelaminated BWP Grade Partical Board in Matt Finish Flat pressed three layer or graded wood partical board conforming to IS No. 12823 of action Tesa/ Greenlam/ Merinolam/Kitlam/Vista as per ISI and approved shade Grade-I type-II in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etcetra complete including carriage of material , within all leads, lifts of materials and other incidentals as per approved drawing, design ,specification and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 28 | Providing and fixing glazing in door, window, ventilator shutters and partitions etcetera with EPDM rubber / neoprene gasket etcetera complete, with plain glass panes of 5 mm ( Five milimetre) thickness (weight not less than 12.50 kg/sqm ( twelve decimal five zero kilogram per square metre) of modi guard / saint gobain as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 29 | Providing and fixing glazing in door, window, ventilator shutters and partitions etcetera with EPDM rubber / neoprene gasket complete, with Frosted Glass 4mm ( four milimetre) thickness (weight not less than 10.00 kg/sqm ( ten kilogram per square metre) of Modi guard / Sanit Gobain as per the architectural drawings, design, specification and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 30 | Providing and fixing 19mm (Nineteen millimetre) thick water proof terminate resistant commercial board Century/Alpro or equivalent in shutters for SDB/cup boards with 6 mm (six millimetre) thick hard wood edging all round and PGI sheet lining in side i/c fixing with nickel plated piano hinges with screws etc complete) including carriage of material ,within all leads, lifts of materials and other incidentals as per approved drawing, design ,specification and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 31 | Providing and fixing the complete box of Cup board shall be made of 25mm (Twenty Five millimetre) thick water proof termite resistant commercial board of Uniply / Green ply/ Century ply / Kitply / Dura ply / Marino ISI marked including shelves.Back side of board shall have 6 to 8 mm (Six to eight millimetre) thick water proof ply all the cut portion of board shall have 6 mm (Six millimetre) thick hard wood edging. The shutter from all side shall be finished with 1mm thick lamination ISI Marked of approved shade of Century / Greenlam /Action Tesa and 19 mm (Nineteen millimetre) thick water proof comercial board of uniply / Greenply for shelves including hinges, handle,knob megnatic catcher complete as per specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Chargeincluding carriage of materials within all leads, lifts and other incidentals. The rate is inclusive of Malkhana, Royality, Octroi, toll tax,GST or any taxes imposed by the Government. |
| 32 | Providing and fixing magnetic catcher of approved quality in upboard / ward robe shutters, including fixing with necessary screws etc. complete.Triple strip vertical type complete as per specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of materials within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 33 | Providing and fixing 65x35mm (Sixty five into Thirty five millimetres) special quality bright finished brass cup-board locks or ward robe locks with six levers including necessary screws etcetra complete as per approved shade including carriage of material ,within all leads, lifts of materials and other incidentals as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 34 | Providing and fixing 25 mm (Twenty five millimetre) dia stainless steel curtain rod having wall thickness of 1.25mm ( one decimal twenty five milimetres) with two chromium plated brass brackets fixed with C.P. brass screws and PVC sleeves etc., wherever necessary complete, including carriage of material ,within all leads, lifts of materials and other incidentals as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 35 | Providing and fixing 300x16mm (Three hundred into Sixteen milimetres) size Pilot/sheel anodized aluminium sliding door bolts anodized transparent or dyed to required colour and shade with necessary screws etc. including carriage of material , within all leads, lifts of materials and other incidentals. as per approved drawing, design ,specification and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 36 | Providing and fixing 250x16mm (Two hundred fifty into Sixteen milimetres) size Pilot/sheel anodized aluminium sliding door bolts anodized transparent or dyed to required colour and shade with necessary screws etc. including carriage of material , within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 37 | Providing and fixing aluminium Pilot/sheel anodized transparent or dyed to required colour and shade with necessary screws etc.Tower bolts (Barrel type) including carriage of material ,within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 38 | 250x10mm (Two hundred Fifty into Ten milimetres) size |
| 39 | 150x10mm (One hundred fifty into Ten milimetres) size |
| 40 | Providing and fixing aluminium Pilot/sheel anodized transparent or dyed to required colour and shade and of approved make with necessary screws etc. handles with the necessary screws etc. complete including carriage of material , within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 41 | 125mm (One hundred twenty five milimetres) size |
| 42 | 100mm (One hundred milimetres) size |
| 43 | Providing and fixing oxidized 150 mm (one hundred fifty millimetre) SIZE aluminium . hooks and eyes complete in all respect including carriage of material ,within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 44 | Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 35 kg to 80 kg ( thirty five kilogram into eighty kilogram) and door width from 700 mm to 1000 mm), ( seven hundred into one thousand milimetres) with double speed adjustment with necessary accessories and screws etc complete including carriage of material , within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 45 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised(anodic coating not less than grade AC 10 as per IS : 1868) transparent or yed torequired colour and shade, with necessary screws etc. complete including carriage of material ,within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 46 | Providing 40x5mm (forty into five millimeter) flat iron hold fast 40cm (forty centimeter) long including fixing to frame with 10mm (ten millimeter) diameter bolts and nuts and wooden plugs and embeding in cement concrete block 30x10x15cm (thirty into ten into fifteen centimeter) 1:3:6 (one cement isto three sand isto six graded stone aggregate 20mm (twenty millimeter) nominal size complete including carriage of material ,within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 47 | Providing 25mm (Twenty five milimetres) thick Kota Stone in flooring / skirting and Treads / Riser of steps 55x55cm (Fifty five into Fifty five centimetres) (Mirror polished) with 7.5 cm (Seven decimal Five centimetres) wide Jaislmer yellow (uniform colour) marble band base of 20mm (twenty millimeter) thick cement mortar 1:4 (One cement: Four sand) laid over and jointed with Grey cement slurry mixed with pigment to match the shade of the slab including rubbing, polishing moulding and nosing complete including carriage of material ,within all leads, lifts of materials and other, incidentals. as per approved architectural drawing, design and specification as directed by the Engineer-in-Charge . The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 48 | Providing and laying 19mm (nineteen millimetre) thick polished Grey Chima Pink granite in workstop where as required having semi round nosing 20mm (twenty millimetre) (average) thickness base of cement mortar 1:3 (one cement isto three sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone including rubbing and polishing complete including carriage of material ,within all leads, lifts of materials and other, incidentals. as per approved architectural drawing, design and specification as directed by the Engineer-in-Charge . The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 49 | Providing and fixing 10mm (ten milimetre) thick double charged matt finished vetrified tiles of Nitco / Simpolo / Orient -Bell / Rak/ Kajaria / AGL/Johnson / Somany as per approved shade and design 600x600mm of size (six hundred millimetre into six hundred millimetre) manufactured of approved shade and colour in flooring /Skirting and landings laid over 12mm (twelve millimetre) thick cement mortar 1:3 (one cement isto three sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete, including carriage of material ,within all leads, lifts of materials and other, incidentals. as per approved architectural drawing, design and specification as directed by the Engineer-in-Charge . The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 50 | Providing and laying 300X300 mm (three hundred into three hundred millimetre) antiskid Ceremic tile of Orient/RAK/Kajaria/Somany/Johnson/ Bell in flooring on 12mm (twelve millimetre) thick cement mortar 1:3 (one cement isto three sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete including carriage of material ,within all leads, lifts of materials and other incidentals, as per approved architectural drawing, design and specification as directed by the Engineer-in-Charge . The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 51 | Providing and laying 300X450 mm (three hundred into four hundred fifty millimetre) white ceramic Glazed tile of Kajaria/ Swastik / Somany / Bell / AGL/Johnson in skirting risers of steps and dados on 12mm (twelve millimetre) thick cement mortar 1:3 (one cement isto three sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete, including carriage of material ,within all leads, lifts of materials and other, incidentals. as per approved architectural drawing, design and specification as directed by the Engineer-in-Charge . The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 52 | Providing and fixing pre-painted steel sheet ridge (factory made) having proper Gola shape or hips of TATA Durashine / Reliance / Jindal Steel corrugation of steel sheet 60cm (sixty centimetre) over all with 0.60mm (zero decimal six zero millimetre) thick prepainted sheet in roofing with hot dipped metalic zinc coated sheets with top coat of regulat modified polyster organic coating of 20 (twenty) microns over 5 (Five) microns primer coating + back coating of polyster of 5 (Five) microns over 5 (Five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (Six millimetre) dia prepainted bitumen washers etc. complete in all respect as per approved specifications, drawing and design and direction by the Engineer in charge including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Malkhana, Octroi, Toll tax, GST or any other taxes imposed by the Government. |
| 53 | Providing and fixing valleys 90 cm (ninety centimetres) over all over all with 0.60mm (Zero decimal Six zero milimetres) thick prepainted sheet ISI marked - Z 120 of sail / TATA / reliance / Jindal roofing with hot dipped metallic Zinc coated sheet with top coat of regular modified polyester (RMP) organic coating of 20 (Twenty) microns over 5 (five) micron primer coating, back coat of polyster of 5 (Five) microns including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (Six milimetres) diametres with prepainted G.I. limpet and bitumen washers complete with all accessories as required, including carriage of materials ,within all leads, lifts of materials and other incidentals as per approved drawing, design , specifications and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 54 | Providing and fixing 0.60mm (Zero decimal Six Zero milimetres) thick prepainted steel sheet ISI marked - Z 120 ( one hundred twenty) of tata Durashine/ sail / reliance / jindal in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster (RMP) organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating to back coat of polyster of 5 (five) microns over 5 (Five) microns primer fixing with prepainted iron J or L hooks,bolts and nuts with prepainted limpet and rubber washers complete with all accessories as required including carriage of materials ,within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 55 | Providing and fixing TATA/durashine/ sail/ Relience/Jindal 30cm (Thirty centimetre) wide 25cm (Twenty five centimetre) deep plain G.I. sheet gutter of 0.60mm (zero decimal six zero millimetre) thick sheet fixed with iron brackets 40X3mm ( forty into three milimetres) size bolts, nuts and washers etcetra having dome shape gratting including making necessary connections with rain water pipe complete including cost and including carriage of material within all leads, lifts of materials and other incidentals as per approved drawing, design, specificstion and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 56 | Providing and fixing plain M.S. B.P. sheet TATA/SAIL/JINDAL 2.00 mm (Two decimal zero millimeter) thick fixed in eaves board / facia / soffits /ceiling including cutting, fixing and welding to steel rafter, member and applying a coat of red lead primer with gas/ electric welding in position complete (frame work is to be measured and paid for separately) including carriage of materials , within all leads, lifts of materials and other incidentals as per approved drawing, design, specification and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 57 | Providing and fixing flashing 38cm (thirty eight centimetre) overall with 0.60mm (zero point six zero millimetre) thick prepainted sheet in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of 20 (twenty) microns over 5 (five) microns primer coating + back coat of polyster of 5 (five) microns over 5 (five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm ( sixty milimetres diametres & prepainted G.I. limpet & bitumen washers complete with all accessories, including carriage of materials, within all leads, lifts of materials and other incidentals as per approved drawing, design ,specification and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 58 | Providing and fixing on wall face 150mm (One hundred fifty milimetres) diametres P.V.C. rain water pipes of working pressure 4/6kg (four / six kilogramme) per square centimetre of finolex / Relience / vectus/ prince pipe for rain water pipe fixed with approved adhesive including filling the joints complete including carriage of materials, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 59 | Providing and fixing on wall face P.V.C. acessories for rain water pipes of working pressure 4/6kg (four / six kilogramme) per square centimetre of finolex / relience / vectus ./ Prince for rain water pipe fixed with approved adhesive including filling the joints complete in all requirement including carriage of materials, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 60 | 150mm (One hundred fifty milimtres) diametrees PVC Plain bend |
| 61 | 150mm (One hundred fifty milimtres)) diametrees PVC shoe |
| 62 | Providing and fixing 150mm ( one hundred fifty milimetres) diameter. PVC holder bat clamps of approved design to P.V.C.. rain water pipe embedded in and including cement concrete blocks 10x10x20cm (ten into ten into twenty centimetres) of 1:2:4 (One cement: Two sand: Four graded crushed stone aggregate 20mm (Twenty milimetres) nominal size and cost of cutting holes and making good the walls etc; including carriage of materials,within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 63 | Providing and fixing 600 x600 x6mm (six hundred into six hundred into six millimetre) Everest Fibre cement board/ACP Pannel of all covering with prepainted G.I. Channel system and 600mm ( six hundred milimetres) including necessary fittings complete in all respect including carriage of materials, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 64 | Steel work welded in built up sections of TATA/SAIL joists channels, angles, tees with connection plates or angles, cleat as in trusses, trussed purlins main and cross beams, hips jack rafters, purlins connected to common rafters and the like in building including cutting, fixing, lifting, hoisting and; placing in position complete and applying a coat of red lead paint including carriage of materials,within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 65 | Providing and fixing handrail 50mm (fifty milimetre) diametre Stainless steel (SST) hollow pipe handrail slip resistant with round ends at two level at 75cm to 90cm (seventy five centimetre to ninety centimetre) height welded to 25mm ( twenty five milimetre) diametre stain less steel hollow pipe balusters. It should extend 30cm (thirty centimetre) beyond the top and bottom of the ramp as per detail of approved drawing , design specificationand direction by the Engineer in charge including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Malkhana, Octroi, Toll tax, GST and any other taxes imposed by the Government. |
| 66 | Providing and fixing staircase railing having hand rail of 50 mm (fifty milimeteres) diametre fixed with 35mm (thirty five milimetre) diametre stainless steel pipe as per detail in combination of 35X35mm (thirty five into thirty five milimetre) stain less steel square pipe and 15/20 (fifteen into twenty ) stainless steel baluster in stair case complete in all respect as per specification, drawing, design and direction by the Engineer in charge including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Malkhana, Octroi, Toll tax, GST and any other taxes imposed by the Government. |
| 67 | Painting two or more coats (including priming coat) on new steel and other metal surfaces with enamel paint brushing of Asian paint/ Nerolac/Berger of approved shade to give an even shade including cleaning the surfaces of all dirt, dust andother foreign matter enamel paint other than white including carriage of materials, within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 68 | Applying priming coat over new wood and wood based surfaces after and including prepering the surface by thoroughly cleaning oil,grease,dirt and other foreign matter) sand papering and knotting with ready mixed paint brushing wood primer pinkincluding carriage of materials, within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 69 | Painting two or more coats of Nerolac/Asian paint/ Berger (excluding priming coat) on new wood and wood based surface with enamel paint other than white to give an even shade including cleaning the surface of dirt,dust and other foreign matter,sand papering and stopingincluding carriage of materials, within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 70 | 6mm (Six milimetres) thick cement plaster in ceiling with cement mortar 1:3 (One cement: Three sand) for above plinth level to all floor level curing complete,including carriage of materials, within all leads, lifts of materials and other incidentals as per approved approved specification, drawings and design. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 71 | 15mm (Fifteen milimetres) thick cement plaster in single coat on rough side of brick/concrete/stone walls for interior plastering Above plinth level to all floor level including arises internal rounded angles, chamfers and or rounded angles not exceeding 80mm (Eighty milimetres) in girth and finished even and smooth with cement mortar 1:6 (One cement isto six sand) curing complete ,including carriage of materials,within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 72 | 6mm (Six milimetres) thick cement plaster in ceiling with cement mortar 1:3 (One cement: Three sand) for above plinth level to all floor level curing complete,including carriage of materials, within all leads, lifts of materials and other incidentals as per approved approved specification, drawings and design. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 73 | 15mm (Fifteen milimetres) thick cement plaster in single coat on fair side of brick/concrete/ stone walls for exterior plastering upto all floor levels including arises internal rounded angles, chamfers and or rounded angles not exceeding 80mm (Eighty milimetres) in girth and finished even and smooth with cement mortar 1:5 (One cement isto five sand)curing complete including carriage of materials, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 74 | Providing Plinth protection with 40 mm (forty millimetre) thick interlocking paver blocks of NTC with 23 cm (twenty three centimetre) dia. Half round R.C.C. pipe for drainage purpose laid base over of 10 cms ( ten centimetre) thickness cement concrete 1:4:8 (one cement isto four sand isto eight graded / crushed stone aggregate) 40mm (forty millimetre) nominal size for bedding of pipe complete including carriage of materials,within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 75 | Applying Birla / J.K white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete above floor level to all floor level,including carriage of materials, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 76 | Finishing wall with Apex weather proof exterior grade emulsion of Asians Paints /Nerolac suraksha /Bergur paint Exterior Emulsion as per approved shade approved design (Apexultima) on undecorated wall surfaces (two or more coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth complete including carriage of materials, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 77 | Wall Painting (two or more coats) with Interior acrylic emlusion paint of Nerolac/ Asian paints of approved brand and manufacture and of required shade on ceiling/sloping roof surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth.Priming coat with distemper primerincluding carriage of materials, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 78 | Providing and laying Dr. Fixit torch shield (IP-3160-3mm) shall be used for water proofing treatment on terrace/depressed portion membrances are made from high grade bitumen and selected polymers, APP/SBS modified bitumen thin coated to non-woven polyster reinforcement to give high care and puncher resistance. The application shall be done as per Architectural drawing, specification including carriage of materials, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 79 | Providing and laying cement concrete 1:2:4 (one cement isto two Sand isto four graded stone aggregate 20mm ( twenty milimetres) nominal size) and curing complete mechanically mixed and vibrated excluding cost of form work in foundation and plinth as per approved specification, drawing and design complete upto floor all level including carriage of materials, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 80 | Providing and laying cement concrete 1:3:6 (1 cement : 3 sand : 6 graded stone aggregate 20 mm (twenty milimetres) nominal size) and curing complete including cost of form work in foundation and plinth including carriage of materials, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 81 | Providing and laying heavy duty 60mm (sixty milimetres) thick inter locking paver blocks precast cement concrete of NTC inter locking paver blocks vibro compacted upto M-50 (M-Fifty) grade including border or kurb block Grey or coloured over sub-base of concrete with 25mm (Twenty five milimetres) thick average thickness of cement mortar 1:4 (One cement : Four sand) laid over and jointed with neat cement slurry mixed with pigment to match the shade of blocks including curing rubbing and polishing complete (sub-base concrete floor to be paid for separately) including carriage of materials, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 82 | Providing and laying cement concrete 1:3:6 (1 cement : 3 sand : 6 graded stone aggregate 20 mm (twenty milimetres) nominal size) and curing complete including cost of form work in foundation and plinth including carriage of materials, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 83 | 1620 (20mm) twenty millimeter diameter pipe O.D. pipe |
| 84 | 1620 (25mm) twenty five millimeter diameter pipe O.D. pipe |
| 85 | Providing and laying 20mm ( Twenty millimetres ) nominal bore in trenches, galvanised mild steel tubes (medium grade), tube fittings completeincluding carriage of materials, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 86 | Providing and placing water tank make P.V.C. SINTEX three layer having capacity of 1000 ( One thousand) liters each tank with necessary fittings including over flow pipe scour pipe etcetera and pads required for in let and out let ball valve with cover and locking arrangements complete in all respect including carriage of materials, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 87 | Making connection of galvanized mild steel distribution branch with galvanized mild steel main 20mm to 40nmm (Twenty milimetres to Forty milimetres)nominal bore by providing and fixing tees including cutting and threading the pipe complete including carriage of materials within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 88 | Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes light grade ISI marked of finolex/vectus/price 4.6mm thick having pressure not less than 6kg /cm2 (six kilogramm per centimetre square) including fixing with approved adhesive etc. complete including carriage of materials within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 89 | 110mm (One hundred ten milimetres) diametres |
| 90 | 75mm (Seventy five milimetres) diametres |
| 91 | Providing and fixing cast iron P.V.C. holder bat clamps ISI marked of approved drawing including steel screw and rawl plug etc. including carriage of materials within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 92 | 110mm (One hundred ten milimetres) diametres |
| 93 | 75mm (Seventy five milimetres) diametres |
| 94 | Providing and fixing P.V.C. I.S.I. marked heal rest of Finolex / Supreme / Prince including filling the joints with including fixing with approved adhesive including carriage of materials, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 95 | 110mm (One hundred ten milimetres) diametres |
| 96 | 75mm (Seventy five milimetres) diametres |
| 97 | Providing and fixing P.V.C. I.S.I. marked plain bend of Finolex / Vectus / Prince including filling the joints with including fixing with approved adhesive including carriage of materials,within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 98 | 110mm (One hundred ten milimetres) diametres |
| 99 | 75mm (Seventy five milimetres) diametres |
| 100 | Providing and fixing P.V.C. I.S.I. marked tees of Finolex / Vectus / Prince including filling the joints with including fixing with approved adhesive including carriage of materials, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 101 | 110mm (One hundred ten milimetres) diametres |
| 102 | 75mm (Seventy five milimetres) diametres |
| 103 | Providing and fixing PVC (polyvinyl chloride) double equal branch with oval access door, insertion rubber washer 3 mm (Three millimetres) thick bolts and nuts ISI marked of Supreme/ Finolex/ Prince complete including fixing with approved adhesive etcetera including carriage of materials, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 104 | 110mm (One hundred ten milimetres) diametres |
| 105 | 75mm (Seventy five milimetres) diametres |
| 106 | Providing and fixing P.V.C. I.S.I. marked collar (confirming to BIS-14735-99) ISI marked of Finolex / Supreme / Prince including fixing with approved adhesive completeincluding carriage of materials, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 107 | 110mm (One hundred ten milimetres) diametres (confirming to BIS-14735-99) |
| 108 | 75mm (Seventy five milimetres) diametres (confirming to BIS-14735-99) |
| 109 | Providing and fixing P.V.C. I.S.I. marked cowl (confirming to BIS-14735-99) ISI marked of Finolex / Supreme / Prince including fixing with approved adhesive complete including carriage of materials, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 110 | 110mm (One hundred ten milimetres) diametres (confirming to BIS-14735-99) |
| 111 | 75mm (Seventy five milimetres) diametres (confirming to BIS-14735-99) |
| 112 | Providing and fixing PVC (polyvinyl chloride) plain “Y\\" junction Finolex / Supreme / Prince ISI marked including fixing with approved adhesive etcetera. complete including carriage of materials, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 113 | 110mm dia (One hundred ten millimetres) diametres |
| 114 | 75mm dia (Seventy five millimetres) diametres |
| 115 | Providing and fixing 110 x 90mm (One hundred ten into Ninety milimetres) P.V.C. I.S.I. marked floor trap of Finolex / Supreme / Prince ISI marked (confirming to BIS-14735-99) of self cleaning design including with approved adhesive cost of cutting and making good walls and floors complete, including carriage of materials,within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 116 | Providing and fixing white vitreous china pedestal type water closet (European type)No 20087 (S - 10 ) Size 57 X 35 X 39 cm ( Fifty seven into thirty five into thirty nine centimetres) with seat and lid, 10 (ten) litre low level white vitreous PVC flushing cistern (sleek Plus) and fixed with Jet pressure of Hindware , Cera ,Jaquar of star white / Snow white shade and as shown in the drawing / as per details & C.P. flush bend with fittings & C.I. brackets, 40 mm ( forty milimetres) flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required complete, including cutting and making good the walls and floors wherever required including carriage of materials, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 117 | Providing and fixing vitreous China wash basin Delta No. 10010 of size 55x40mm (Fifty five is to forty milimetres) without pedestal of Hindware / Cera /Jaquar of star white / Snow white shade with mirror above and as shown in the drawing / as per details with single hole for pillar tap including 15 mm (fifteen millimetre) C.P. brass pillar tap with C.I. brackets, 32 mm (thirty two millimetre) C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require including carriage of material ( Mirror to be paid for separately), including carriage of materials, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 118 | Providing and fixing stainless steel kitchen sink size 610 x510 mm (six hundred ten into four hundred sixty millimetre) with bowl depth 200 mm (two hundred millimetre) of AMC unik / diamond approved standard ISI make with drain board and C.P. waste with C.I. or M.S. Brackets painted including cutting holes and making good the same but excluding fitting including carriage of materials, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 119 | Providing and fixing 15 mm ( fifteen milimetre) nominal bore C.P. brass pillar tap (concealed) Continental series of Jaquar / Classik series of Hindware / Floral series of Cera / Vintage series of Kerovite & Hindon series of Jal of standard design and of approved make conforming to IS : 8931 , including carriage of materials, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 120 | Providing and fixing 32mm (Thirty two millimetres) nominal size diametres rubber plug for wash basin including carriage of materials,within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 121 | Providing and fixing 32mm dia (Thirty two millimetres) diametres M.I. union for wash basin or sink complete including carriage of materials, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 122 | Providing and fixing 32mm (Thirty two millimetres) diametres C.P (chromium plated) brass waste and plug for glazed ware sinks, basins etcetera. with long screwed shank and fly nut and fixed to steel pipe including vulcanite plug, brass chain and stud complete including carriage of materials, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 123 | Providing and laying cement concrete 1:5:10 (One Cement isto Five Sand istoTen graded stone aggregate 40mm (Forty millimetres) nominal size 150mm ( One Hundred fifty milimetre ) thickness bedding for 230mm (two hundred thirty millimetres) dia pipe including, necessary form work and curing complete including carriage of materials, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 124 | Providing and fixing 100mm (One hundred millimetres) diametres C.P. (Chromium plated) Grating Continental series of Jaquar / Contessa series of Hindware /Ocean series of Cera / Vintage series of Kerovite & Hindon series of Jal for gully floor or Nahni trap including carriage of materials, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 125 | Providing and fixing flat back 600x450mm (Six hundred into Four hundred fifty millimetres) beveled edge mirror Continental series of Jaquar / Contess series of Hindware /Ocean series of Cera / Vintage series of Kerovite & Hindon series of Jal of superior glass mounted on 6mm (Six millimetres) thick A.C. asbestos cement sheet or ply wood sheet and fixed to wooden plugs with C.P. (Chromium plated) brass screws and washers complete including carriage of materials, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 126 | Providing and fixing 600mmx20mm (Six hundred millimetre into Twenty millimetres) Continental series of Jaquar / Contess series of Hindware /Ocean series of Cera / Vintage series of Kerovite & Hindon series of Jal brass Towel rail with C.P. (Chromium plated) brass brackets fixed to wooden plugs with C.P.(Chromium plated) brass screws complete within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 127 | Providing and fixing 600mmx120mm (Six hundred millimetres into One hundred twenty millimetres) glass shelf Continental series of Jaquar / Contess series of Hindware /Ocean series of Cera / Vintage series of Kerovite & Hindon series of Jal brackets and guard rail fixed to wooden plugs with C.P.(Chromium plated) brass screws complete including carriage of materials, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 128 | Providing and fixing C.P. brass each toilet paper holder of Continental series of Jaquar / Contess series of Hindware /Ocean series of Cera / Vintage series of Kerovite & Hindon series of Jal complete including carriage of materials, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 129 | Providing and fixing chromium plated brass soap dish with C.P.(chromium plated) Brass brackets fixed to wooden cleats with C.P. (chromium plated) Brass screws complete including carriage of materials, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 130 | Providing and fixing 100mm dia (one hundred millimetres) diametres C.P. (chromium plated) Brass shower rose with 15mm (Fifteen millimetres) or 20mm (Twenty millimetres) inlet complete Conforming ISI Marked IS No. 182202 (one lacs eighty two thousand two hundred two ) including carriage of materials, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 131 | Providing and fixing 15mm dia (Fifteen millimetres) diametres nominal bore chromium plated brass bib cock tap (superior or heavy type) Conforming to 8931 (eight thousand nine hundred thirty one ) of Jaquar / Contess series of Hindware /Ocean series of Cera / Vintage series of Kerovite & Hindon series of Jal complete including carriage of materials, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 132 | Providing and fixing 15mm dia (Fifteen millimetres) diametres C.P. (chromium plated) brass tab cock Conforming to 8931 (Eight thousand nine hundred thirty one) of Jaquar / Contess series of Hindware /Ocean series of Cera / Vintage series of Kerovite & Hindon series of Jal complete including carriage of materials, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 133 | Providing and fixing 15mm dia (Fifteen millimetres) diametres C.P. (chromium plated) brass stop cock Conforming to 8934 (Eight thousand nine hundred thirty four) of Jaquar / Contess series of Hindware /Ocean series of Cera / Vintage series of Kerovite & Hindon series of Jal complete including carriage of materials, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 134 | Providing and fixing 15mm (Fifteen millimetres) nominal bore PVC (polyvinyl chloride) connection pipe with brass union 30/ 45cm (Thirty or Forty five Centimetres) length complete including carriage of materials, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 135 | Providing and fixing 15mm (Fifteen millimetres) nominal bore ( chromium plated) brass full way valve with wheel Conforming to 8931 (Eight thousand nine hundred thirty one) of Jaquar / Contess series of Hindware /Ocean series of Cera / Vintage series of Kerovite & Hindon series of Jal complete within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 136 | Providing and fixing 15mm (Fifteen milimetres) diametres C.P.brass angle valve without nuts of Conforming to 8931 (Eight thousand nine hundred thirty one) of Jaquar / Contess series of Hindware /Ocean series of Cera / Vintage series of Kerovite & Hindon series of Jal complete including carriage of materials, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 137 | Providing and fixing 15mm (Fifteen milimetres) nominal bore C.P. brass valve (Horizontal plunger) type High pressure with polythene plastic floats of Conforming to 8931 (Eight thousand nine hundred thirty one) of Jaquar / Contess series of Hindware /Ocean series of Cera / Vintage series of Kerovite & Hindon series of Jal complete including carriage of materials, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 138 | Constructing brick masonry manhole in cement mortar 1:4 ( one cement isto four coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (one cement isto one decimal five coarse sand (zone- III) isto three graded stone aggregate 20 mm ( twenty milimetres) nominal size), foundation concrete 1:4:8 mix (one cement isto four coarse sand (zone- III) isto eight graded stone aggregate 40 mm ( forty milimetres) nominal size), inside plastering 12 mm ( twelve milimetres) thickness with cement mortar 1:3 (one cement isto three coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (one cement isto two coarse sand isto four graded stone aggregate 20 mm ( forty milimetres) nominal size) finished with a floating coat of neat cement complete as per standard design Inside size 90x80 cm ( ninety into eighty milimetres) and 45 cm (forty five centimetres) deep including C.I. cover with frame (light duty) 455x610 mm ( four hundred fifty five into six hundred ten milimetres) internal dimensions, total weight of cover and frame to be not less than 38 kg ( thirty eight kilogram) (weight of cover 23 kg ( twenty three kilogram )and weight of frame 15 kg ( fifteen kilogram) With Sewer bricks conforming to IS : 4885 , including carriage of materials, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 139 | Constructing brick masonry manhole in cement mortar 1:4 (one cement isto four coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (one cement isto one decimal five coarse sand (zone- III) isto three graded stone aggregate 20 mm ( twenty milimetres)nominal size), foundation concrete 1:4:8 mix (one cement isto four coarse sand (zone- III) isto eight graded stone aggregate 40 mm ( forty milimetre) nominal size), inside plastering 12 mm ( twelve milimetres) thick with cement mortar 1:3 (one cement isto three coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (one cement isto two coarse sand isto four graded stone aggregate 20 mm ( twenty milimetres) nominal size) finished with a floating coat of neat cement complete as per standard design Inside size 120x90 cm ( one hundred twenty centimetres) and 90 cm ( ninety centimetres) deep including C.I. cover with frame (medium duty) 400x610 mm ( four hundred into six hundred ten milimetres) internal diameter, total weight of cover and frame to be not less than 38 kg ( Thirty eight kilogram) (weight of cover 23 kg ( twenty three kilogram) and weight of frame 15 kg ( fifteen kilogram) ) : With Sewer bricks conforming to IS : 4885, including carriage of materials,within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 140 | Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (one cement isto four coarse sand) C.I. cover with frame (light duty) 455x610 mm ( four hundred fifty five into six hundred ten milimetres) internal dimensions, total weight of cover with frame to be not less than 38 kg ( thirty eight kilogram) (weight of cover 23 kg ( twenty three kilogram) and weight of frame 15 kg ( fifteen kilogram), R.C.C. top slab with 1:1.5:3 mix (one cement isto one decimal five Fine sand isto three graded stone aggregate 20 mm ( twenty milimetres) nominal size), foundation concrete 1:5:10 (one cement isto fivefine sand isto ten graded stone aggregate 40 mm ( forty milimetres) nominal size), inside plastering 12 mm ( twelve milimetres) thick with cement mortar 1:3 (one cement isto three coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etcetera complete as per standard design Inside dimensions 455x610 mm ( four hundred fifty five into six hundred ten milimetres) and 45 cm ( forty five centimetres) deep for single pipe line with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 ( seven decimal five) including carriage of materials,, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 141 | Excavating trenches of required width for pipes, cables, etcetera including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto any depth including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm (twenty centimetres) in depth, including consolidating each deposited layer by ramming, watering, etcetera. and disposing of surplus excavated, including carriage of materials, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 142 | Supplying cast iron cover with rectangular frame for internal dimension 455mmx610mm ( four hundred fifty five milimetres into six hundred ten milimetres) rectangular C.I. Cover (light duty single seal pattern-1) the weight of cover not less than 23kg. ( twenty three kilograms), including carriage of materials,within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 143 | Provision for water pump 1.00 HP (one horse power) of Kirlosker Delta within all leads, lifts of materials and other incidentals, as per approved architectural drawing, design and specification as directed by the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 144 | Providing and laying 20mm ( Twenty millimetres ) nominal bore in trenches, galvanised mild steel tubes (medium grade), tube fittings complete as per H.P.P.W.D specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Charge iincluding entire carriage of materials within all leads lifts and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government. |
| 145 | Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm ( twenty centimetre) in trenches, plinth, sides of foundation etc. complete , as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 146 | Earth work in excavation for all type of road structure such as retaining walls, breast walls, culverts, drains and parapets etcetera in all type of classification of soil comprising of ordinary soil, ordinary rock, hard rock chiseling /wedging out rocks (Where blasting is prohibited) as per drawings and M.O.R.D. technical specification clause 305 & 1603 and as per direction of the Engineer- In – Charge including setting out, shoring and bracing, removal of stumps and other deleterious materials and disposal of materials upto any lead and lift including dressing of sides and bottom and back filling in trenches with excavated suitable approved material to the original surface in layers not exceeding 150mm ( one hundred fifty milimetres) compacted thickness including shoring and strutting and pumping and bailing out water (surface and sub soil water) upto any depth and any quantam of water including cleaning of slush which may arrise out during dewatering , as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 147 | Providing and laying 100mm (Hundred millimeter) dia P.V.C pipe weep holes in brick masonry/stone masonry, plain reinforced concrete, Abutments, Wing walls, Return walls and retaining/breast walls extended through the full width of the structure with slope I(V):20(H)(One vertical : Twenty Horizontal) towards draining face complete as per drawing and MORD technical specification Clause 1206.6 and as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 30, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 05, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 5 daysAug 06, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 6 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender