Tender For Special Repair Of Roof Terrace, And Establishment Of Breast Feeding Corner And Biomedical Waste Corner At Aam Sector 50, Chandigarh
Tender Value
6.85 Lakhs
Estimated cost
Bid Submission
06 Aug 2026
2 days left
EMD
13707
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Chandigarh → Chandigarh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repair Of Roof Terrace, And Establishment Of Breast Feeding Corner And Biomedical Waste Corner At Aam Sector 50, Chandigarh
BOQ
| Sl. No. | Item Description |
| 1 | Re-grading terracing of mud phaska covered with tiles or brick, in cement by dismantling tiles or bricks, removing mud plaster preparing the surface of mud phaska to proper slope relaying mud plaster gobri leaping and tiles or bricks, grouted in cement mortar 1:3 (1 cement : 3 fine sand) including replacing unserviceable tiles or bricks with new ones and disposal of unserviceable material to the dumping ground (the cost of the new tiles or brick excluded) within 50 metres lead. |
| 2 | Painting top roofs with bitumen of approved quality at 17kg per 10 sqm impregnated with a coat of coarse sand at 60cudm per 10sqm including cleaning the slab surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil complete (with residual type petroleum bitumen of penetration VG-10 bulk to the entire satisfaction of the E.I.C(DSR : 12.15.1) |
| 3 | Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1mx 1mx 400 micron, finished with 12mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement rounding the edge and making and finishing the outlet complete. (DSR 12.22) |
| 4 | Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement: 2 coarse sand : 4stone aggregate 10mm and down gauge) including finishing with cement mortar1:3 (1 cement: 3 fine sand) as per standard design :12.21.1 In 75x75mm deep chase (DSR: 12.21.1) |
| 5 | Pointing on brick work or brick flooring with cement mortar 1:3 (: 1 cement : 3 fine sand) ( Flush/Ruled/Stuck or weathered pointing )(DSR 13.31.1) |
| 6 | Extra Rate for New Brick Tile |
| 7 | Credit of old dismantled roof tile brick bat |
| 8 | Providing and fixing aluminium work for door, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other section of approved make confirming to IS: 733 and IS: 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners inclusding necessary filling up of gaps at juctions, at top, bottom and sides with required PVC neoprene fell etc. Aluminium section shall be smooth, rust free, straight, mitred and jointed machanically wherever required including cleat angle, Aluminium snap beading for glazing/panelling C.P bass/stainless steel screws. all complete as per architectural drawings and the derection of Engineer-In-Charge. (Glazing and panelling to be paid for separately) for fixed portion: - Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, minimum anodic coating of grade AC15) For fixed portion.(DSR : 21.1.1.1) |
| 9 | For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15 (DSR : 21.1.2.1) |
| 10 | Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer-in-charge.Pre-laminated particle board with decorative lamination on both sides (DSR : 21.2.2) |
| 11 | Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete in all respecte to the entire satisfaction of the Engineer-In-Charge. 125mm (DSR : 9.100.1) |
| 12 | Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete in all respecte to the entire satisfaction of the Engineer-In-Charge. 150 x10mm (DSR : 9.97.4) |
| 13 | Providing and fixing M.S. Angle frame with IRC Jali of size 1”x1” (10 gauge) with welding M.S. angle frame having size 40x40x5 including M.S. flat size 40x5 mm which is having 3 Nos different compartment with 3 nos openable door welded with frame, The size of frame 11'-6\\"x 3'-6\\" with height of 7'-0\\" hold along existing wall with holdfastner as per drawing.The rate also includes the 2 cost of special quailty paint over one coat of primer complete in all respects to the entire satisfaction of Engineer –in –Charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 30, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 06, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 2 daysAug 06, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 2 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender