Tender For Addition/Alterations And Special Repairs Of Selected Old Married Accommodations At Ahmedabad Military Station
Tender Value
11.50 Crore
Estimated cost
Bid Submission
27 Aug 2026
11 days left
EMD
9 Lakhs
Bank guarantee accepted
Document Fee
3000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Ahmedabad → Gujarat
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Addition/Alterations And Special Repairs Of Selected Old Married Accommodations At Ahmedabad Military Station
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removing the rubbish off materials out side of Ministry of defence (MOD) land complete all as specified and directed. |
| 2 | Demolition of concrete of any description and in any position not other wise specially provided for cement concete (unreinforced) including removal of debris debries/rubbish off materials out side of Ministry of defence (MOD) land complete all as sppecified and directed. |
| 3 | Roughening the surfaces of old concrete floor by picking, sweeping, cleaning and washing down with water to remove dust and brushing neat cement slurry with 3.0 kg of cement per Sqm complete all as specified and directed |
| 4 | M&L for 25 mm thick Plain cement concrete type B-0, (1:2:4) using (12.5 mm graded crushed stone aggregate) as in floor finished even and rough to received top layer or tiling complete all as specified and directed |
| 5 | M & L for non skid ceramic (colored), 7 to 8 mm thick as in floor area of each tile exceeding 0.6 Sqm but n exceeding 0.11 Sqm, set and jointed in neat cement slurry and pointed in white or colored cement to match incluckuding over screed bed or beeding layers of mortar 15mm thick in cement mortar 1:4 in floors, complete all as specified and directed. |
| 6 | M&L for Glazed ceramic tiles coloured (300x450mm) x 7mm thick, in wall/dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick backing coat of tiles in cement mortar (1:3) complete all as specified and directed. |
| 7 | M&L for Non - skid Ceramic tiles light shade 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick in cement mortar 1:4 screed bed complete all as specified and directed. |
| 8 | M&L for Non - skid Ceramic tiles light shade 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick backing coat of tiles in cement mortar (1:3) complete all as specified and directed. |
| 9 | M&L for matt finish Vitrified tiles light shade 9-10 mm, (square or rectangular) area of each tile n. exc 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed cement mortar 1:4 complete all as specified and directed. |
| 10 | All as per item No 9 above but on vertical surfaces including 9-10 mm thick backing coat of tiles in 10 mm thick cement mortar (1:3) complete all as specified and directed. |
| 11 | M&L machine cut Kota stone slab 20-25 mm thick as in flooring or trades of step incl half round moulding over and including screed bed 20 mm thick in cement mortar (1:3) laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including cutting, rubbing and polishing complete all as specified and directed. |
| 12 | M&L machine cut Kota stone slab 20-25 mm thick as in riser to step including 10 mm thick rendring in cement mortar (1:3) laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including cutting, rubbing and polishing complete all as specified and directed. |
| 13 | Demolition of stone slab and tiles of any description or thickness as in floors, apron etc. laid, bedded and pointed in any mortar complete all as specified and directed. |
| 14 | M&L for 18-20 mm thick Granite (of any type) work (table rubbed and polished) in cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including 15 mm thick screed bed in cement mortar 1:4 and providing necessary holes for gas pipe / water supply pipe etc. complete all as sppecified and directed. |
| 15 | M&L Marble work any shed other than white or black 18-20mm thick (table rubbed and polished) in steps, jambs, pillars, windowcills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade including 15 mm thick cement plaster in cement mortar 1:4 complete all as sppecified and directed. |
| 16 | Taking down of existing unserviceable water proofing treatment with PCC padding, cement plaster etc of any description and cleaning of top surfaces of cement concrete flushing out junction of parapet walls and washing down with water including removing the rubbish off materials to a distance exceeding 500 m but not exc 1 KM complete all as sppecified and directed. |
| 17 | M&L for providing Water Proofing Treatment to RCC Roof / stone patti surfaces with APP Membrane & roof tiles in the following steps including benching at the junction of wall & roof all as directed.(a) M&L for Rendering 5 mm thick on on fair faces of concrete surfaces on PCC padding in CM 1:3 mixed with and including liquid water proofing compound ISI market as per manufacturer instruction and finish the surface even and smooth without using extra cement for laying APP membrane all as directed. (b) M&L preparation of plastered surface of roof slab by throughly wire brushing washed dried up cleaned all foreign matter and dust and apply one coat of approved bituminous primer@ 0.40 ltr per sqm complete all as specified and directed complete(c) M&L for 3 mm thick APP modified polymeric membrane minimum weight 3kg/sqm and reinforced with non woven polyster reinforcement shall be laid by torch application method over a coat of bitumen S-35 grade C 30/40 applied @ 1.20 Kg/Sqm Note:-APP modified polymeric membrane shall be all as specified & directed. The side overlaps shall be minimum 75mm and end laps shall be minimum 100mm. All Overlaps shall be sealed as per manufacturer's instructions.(d) Providing 40 mm thick PCC 1:2:4 type B-0 (12.5 mm thick graded stone aggregate) as top layer, complete all as specified and directed. |
| 18 | Supply only integral water proofing compound conforming to IS: 2645 - 1975 specification complete all as specified and as directed |
| 19 | Disconnecting existing tanks exc. 250 and n.exc. 500, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required re-connecting and re-fixing inposition complete all as specified and as directed. |
| 20 | S&F Rotational moulded poly-ethylene three layer water storage tanks (cylinderical vertical with closed top) 500 litres capacity, white in colour hoisted and fixed in position with and including all fittings 25 mm dia CPVC tank adaptor & 20mm Ball valves high pressure of PTMTand fixtures and as per TD Drg No CEJZ/TD/14 of 1/1 dt 04.10.2013 complete all as specified and directed. |
| 21 | Disconnecting existing tanks exc. 500 and n.exc. 1000, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required re-connecting and re-fixing inposition complete all as specified and as directed. |
| 22 | S&F Rotational moulded poly-ethylene three layer water storage tanks (cylinderical vertical with closed top) 500 litres capacity, white in colour hoisted and fixed in position with and including all fittings 25 mm dia CPVC tank adaptor & 20mm Ball valves high pressure of PTMTand fixtures and as per TD Drg No CEJZ/TD/14 of 1/1 dt 04.10.2013 complete all as specified and directed. |
| 23 | M&L for PCC (1:3:6), type C-2 with using 40mm graded crushed stone aggregates as in platform for PVC tank all complete as specified and as directed. |
| 24 | Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting not exc 10 cm girth complete all as specified and directed |
| 25 | Taking up or down existing unserviceable mild steel water tubing and connections 15mm dia, any grade, of any description or in any position including fittings & removing to store complete all as specified and as directed. |
| 26 | Supplying and laying of 20 mm outer dia CPVC pipes SDR 11 and plain CPVC SDR 11 fittings, concealed joint with CPVC adhesive taflon tape complete to walls and ceilings or laid in floors including all connected brass cpvc fittings and cutting grooves, filled with cement mortar 1:6 complete all as specified and as directed. |
| 27 | Taking up or down existing unserviceable mild steel water tubing and connections 20mm dia, any grade, of any description or in any position including fittings & removing to store complete all as specified and as directed. |
| 28 | Supply, fixing & laying GI tubing of 20 mm bore, medium grade with both end threaded in any length including cutting threading connection in new or old position including provision of all type of GI fitttings for wall/ceilling/floor complete all as specified and directed. |
| 29 | Taking down cement plaster on brick/stone or concrete surfaces including racking out joints, hacking for key, scrubbing down with water to receive plaster including necessary all scaffolding complete all as specified and as directed. |
| 30 | M&L for rendering on fair faces of brick work in two layers i.e., 10 mm thick in CM 1:6 and top layer of 5 mm thick in CM 1:4 mixed with water proofing compound in top layer @3% by the weight of cement or as per manufacturer's instructions finishing the surface fair and even without using extra cement complete all as specified and as directed.Note:-Liquid water proofing compound shall be measured and paid for separately as “Supply only” |
| 31 | S&F for Butt hinges, Medium weight, cold rolled mild steel, and fixed 100mm size complete all as specified and as directed. |
| 32 | M&L for PCC 1:2:4 type B0 using 12.50mm graded crushed stone aggregate in roof etc. as levelling coarse etc. all as specified and as directed by Engineer-in-Charge |
| 33 | M&L 10 mm thick rendering in cement mortar 1:6 on fair face of brick work or concrete surface finishing the surface fair and even complete all as specified and directed. |
| 34 | Prepration of surface newly plastered or un plastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer after applying cement based wall care putty 1.5 mm thick to wall surface complete all as specified and directed. |
| 35 | Prepration of surfac newly plastered or un plastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer to wall surface complete all as specified and directed. |
| 36 | Complete removal of existing treatment of old plastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer after applying cement based wall care putty 1.5 mm thick to wall surface including preparing old decorated surfaces complete all as specified and directed. |
| 37 | Complete removal of existing treatment of old plastered surfaces of walls and applying two coats of oil bound distemper to wall surface including prepration of old surface complete all as specified and directed. |
| 38 | M&L guniting for shortcrete 1 :2 (CM) mixed with epoxy resin and hardner (manufactured by FOSROC/MC BAUCHEMIC /CICO/PIDILITE) @ 2% by weight of cement in equal proportion using short crete pumps and allied equipment,in thickness 30 mm all as per manufactureres instruction.(Upto 5 mtr height) including necessary chiping/taking down loose concrete along with application of rust remover for old rusted bars and rebar if required followed by application of anti corrosive paint (nitozink primer) @.25 lt/sqm over old /rebar followed with application of one coat epoxy bonding agent (Nito Bond EP) to old concrete surface as per manufacturers instruction complete all as specified and directed. |
| 39 | S& F mild steel welded fabric of weight exe 2.5 Kg but n.exc. 4 Kg/ Sqm, fixed to steel members with spikes complete all as specified and directed. |
| 40 | M&L for rendering 5mm thick plastering in CM (1:3) on ceiling, soffits of slabs, chajjas, columns and beams etc and finished the plastered surface even and smooth without using extra cement complete all as specified and directed. |
| 41 | M&L preparing newly plastered or unplastered surface of ceiling and applying three coats of white washing complete all as specified and directed. |
| 42 | M&L complete removal of existing treatment, scraping down, washing, rubbing down of old plastered surfaces of ceiling and applying three coats of white washing including prepration of old surface complete all as specified and directed. |
| 43 | Demolition of Brickwork or stone/ boulder masonry, built in lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed. |
| 44 | M & L for brick work with sub class ‘B’ old size bricks, straight or curved on plan and any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed. |
| 45 | M&L brickwork with sub class B bricks straight or curved on plan exc 6mtr mean radius built in cement mortar 1:6 by using old size bricks complete. |
| 46 | M & L for providing plain cement concrete type B-1, 1:2:4, (using 20 mm graded crushed stone aggregate), as in benching, copings, bed block for filing hollow space of steel chowkhats, including weathering, slightly rounded or chamfered angles & throating as directed including necessary form work as required complete all as specified and directed. |
| 47 | M&L for 15mm thick rendering on vertical side of sunken floor of brick/ concrete surfaces in cement mortar (1:3) mixed with water proofing compound as per manufacture instrution and finished even and smooth without using extra cement complete all as specified. (Note : WPC shall be measured and paid seperately) |
| 48 | M&L for PCC 1:1½:3 nominal mix type A-0 using 12.5 mm graded crushed stone aggregate mixed with water proofing compound as per manufacture instruction on bottom of sunken portion with slope towards spout including applying two coat of polymeric base chemical in the top surface of PCC and side of sunken portion complete all as specified. (Note : WPC shall be measured and paid seperately) |
| 49 | M&L for PCC 1:5:10 type E-2 (using 40 mm graded stone aggregate) as in lean concrete in sunken floors complete all as specified and directed. |
| 50 | S&F 50 mm bore pipe medium grade galvanised iron water tube with all fittings laid in floors fixed to wall for spout etc complete including taking down old pipe complete all as specified and as directed. |
| 51 | S&F in repairs vitreous china wash basin, white, flat back, size 550x400m excluding taps, waste , chain & plug & porcelain stopper including brackets including cutting for pinning in ends of bracketes or erecting stand and fixing and supply and waste pipe complete all as specified and directed |
| 52 | S&F in repairs 600mm x 450 mm bevelled edge mirror of selected quality, mounted on 6 mm thick AC plain building board or commercial plywood and fixed to wall on wooden plugs with chromium plated brass screws and cup washers all complete as specified and as directed. |
| 53 | S&F in repair 10 ltr capacity PVC flushing cistern low level white colour including PVC connection PVC flush pipe of required length complete all as specified and directed. |
| 54 | S&F in repairs vitreous china squatting pan, ‘Orissa’ pattern, size 580 mm x 440 mm, white with integral foot rests, including CI 'P' or 'S' trap, embedded and set in PCC 1:5:10 type E-2 and making good to floor including removing rubbish with and including and PVC flushing pipe, 32 mm dia complete all as specified and as directed. |
| 55 | S&F in repair vitreous china wash down water closet pan (pedestral pattern), white including connection trap and to flushing pipe, anti-syphnoge pipe etc complete all as specified and as directed. |
| 56 | S&F in repair PVC seat cover for pedestal pan, white closed pattern with flat bottom and cover and mild steel chromium plated or aluminiumised hanging device complete all as directed. |
| 57 | S&F in repair 15 mm bore stop cock / angle cock with flage (CAT Part No-PIS-10H or euivalent) complete all as specified and direcrted |
| 58 | Supply only central hole basin mixer for WHB complete all as specified and directed.(Cat part No 8550 of Make-Prayag or its equivalent make). |
| 59 | S&F in repair CP brass 600 mm D type towel rail complete all as specified and directed. |
| 60 | S & F in repairs chromium plated soap dish complete all as specified (Cat No CPA-42 of make Prayag or its equivalent make). |
| 61 | S&F in repair CP toilet paper holder CAT Part No-CPA-09 of make Prayag or equivalent complete all as specified and directed. |
| 62 | S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed. |
| 63 | S & F in repairs corner glass shelf 300mm complete all as specified and directed. (Cat No CPA-30 of make Prayag or its equivalent make). |
| 64 | S&F 0.60 mm thick stainless steel plate rack of size 31\\"x36\\"x10\\" complete all as specified and directed. (Make -Cat No PSP-3 or its equivalent make). |
| 65 | S&F in repairs Bib taps (long body) fancy type cast copper alloy, chromium plated for 15mm bore pipe, screwed for iron pipes or for brass ferrule all complete as specified and as dierected. |
| 66 | S & F in repair 15mm bore PVC Connection with PTMT nut of length 450 mm complete all as specified and directed |
| 67 | Supply and fix in repair pillar taps, cast copper alloy with capston heads, chromium plated, screwed down high pressure, with or without lettered hot or cold with long screwed shanks and fly-nuts, screwed for iron pipe 15mm bore complete all as specified and directed. |
| 68 | S&F in repair brass CP shower rose 125 mm size with or without swivel joint and fixing to steel pipe complete all as specified and directed |
| 69 | S&F in repairs stop valves fancy type cast copper alloy, chromium plated with long shank and cup (concealed type) for 15mm bore pipe, screwed both ends including necessary fittings such as sockets for pipe or for union all complete as specified and as directed. |
| 70 | S & F in repair Grating doom 125 mm dia with waste hole of PTMT (Minimum weight 40gms) complete all as specified and directed |
| 71 | S& F in repair sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed. |
| 72 | Supply and fixed in repairs sinks with drainage board made of stainless steel 1mm thick sheet plugs, washers and waste pipe, including a pair of cantilever brackets embedded in wall with suitable size of PCC (1:3:6) type C-1 blocks and connecting union to pipe of overall size 915mm x 460mm & bowl size 410mm x 330mm x 160mm all complete as specified and as directed. |
| 73 | Dismaintling of 75mm to 100 mm internal dia of cast iron pipe jointed in cement mortar and taking out of trenches or any description and any position as required complete all as specified and directed. |
| 74 | S&F of PVC (SWR) pipe 110 mm dia, conforming to IS-13592-1992 type 'B', double socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed. |
| 75 | S&F of PVC (SWR) pipe 75 mm dia, conforming to IS-13592-1992 type 'B',double socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed. |
| 76 | S&F of 110 mm bore PVC (SWR) bends/tee any radius complete all as specifed and directed. |
| 77 | S&F of 75 mm bore PVC (SWR) bends/tee any radius complete all as specifed and directed. |
| 78 | S&F of 110 mm bore PVC (SWR) cowls complete all as specifed and directed. |
| 79 | Taking down chowkats or frames with shutters (without taking off shutters from the frames) exceeding 1.5 sqm but not exceeding 4 sqm each and removing from site complete all as specified and directed. |
| 80 | Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exceeding 1.5 sqm each and removing from site complete all as specified and directed. |
| 81 | Taking down shutter of any description but exc 1 sqm and n. exc. 2 sqm each complete all as specified and directed. |
| 82 | S&F of mild steel angle iron work as in doors frames, chajja hollow square sections conforming to 410W (Gde E-250) quality-B including fixing of hold fast and hinges complete all as specified and directed. |
| 83 | M&L Factory made flush shutter 35mm thick solid core construction with block board core and ply wood face panels, commercial type on both side and covered with decorative face veneer both side with lipping/frame to match complete all as specified and directed. |
| 84 | S&F factory made 35 mm thick 2nd class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauge, etc., divided into squares, with plain, chamfered or rounded, mitred and rebated sash members, any numbers and mited beads for securing glass, etc., sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.20(a) supplied and fitted to chowkats complete all as specified and directed. |
| 85 | S&F stainless steel wire cloth 0.36 nominal dia wire & average width of aperature 1.40 mm fixed with stainless steel wire staples complete all as specified and directed |
| 86 | S&F 200 mm long Aluminium anodised barrel tower bolts. complete all as specified and directed. |
| 87 | S&F 150 mm size aluminium anodised door handles complete all as specified and directed. |
| 88 | M&L for sliding door bolt of 300mm long plate Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed. |
| 89 | S&F 300 mm ordinary mild steel rat tail rod pattern spring including roller and roller plate complete all as specified and directed |
| 90 | M&L preparation of new untreated wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 91 | S&F Factory made solid panel pace door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel heaving a PVC sheet strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing on page No 176-177 of SSR Part-II complete all as specified and directed. |
| 92 | Solid PVC door frame of size 50x47mm made out of 5mm thick plain colour PVC sheet reinforced with MS square tube, supplied and fixed in repair in opening as per specification and drawing complete as directed. |
| 93 | S&F stainless steel butt hinges medium weight 100 mm long complete all as specified and directed |
| 94 | S&F Continuous (piano) hinges, 30mm width of flaps (when open) mild steel, bright finish or electrogalvanised complete all as specified and directed. |
| 95 | S & F powder coated anodised Aluminium alloy sections sliding windows 3 track sliding shutters duly fitted with neoprene beading, glazing clips, two shutters glass panes 4.80 mm nominal thickness one shutter with stainless steel wire cloth 0.45mm dia and average width of aperture 1.4mm , aluminium alloy handles etc. as shown in TD Drwg No -CEJZ-/63 sheet No-1/3 and 2/3 incluinge all glazing/aluminium wire cloth, rubber packing, joining, cleats, glazing clips, aluminium snap beading, locking arrangements, handle with or without opeing for AC etc., complete all as specified and directed. Note :Rates include all glazing/aluminium wire cloth, rubber packing, joining, cleats, glazing clips, aluminium snap beading, locking arrangements, handle with or without opeing for AC etc., as directed by Engrs-in-Charge. |
| 96 | S&F aluminium anodised ventilator with fixed aluminium frame fixed in vertical position with aluminium vertical members and 1/3 portion to be provided with 6.30mm thick fixed figured glass and remaining 2/3 portion to be louvered using 4mm thick figured, including rubber gasket and aluminium beading as shown in TD Drwg No -CEJZ-/12 sheet No-2/2 complete all as directed. |
| 97 | S & F of mild steel work such as window guard bars and similar work conforming to Fe – 290 Grade – E 165 complete all as specified and directed. |
| 98 | S&F in repair 25 mm dia drapery rod of MS chromium plated fixed to wall with fancy bracket & knobs complete all as specified and directed. |
| 99 | M&L preparation of new untreated Steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome complete all as specified and directed. |
| 100 | M&L for preparation of old steel surface of any description over 10cm width or girth and applying one coats of synthetic enamel paint complete all as specified and directed. |
| 101 | S&F pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of colour as approved by GE and having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 102 | S&F 100 mm size aluminium anodised door handles complete all as specified and directed. |
| 103 | M&L 75mm thick PCC,1:2:4, type B-2 as in plinth protection/footpath using 40mm graded crushed stone aggregate finishing cement concrete surface even & smooth without using extra cement including impression and glass strip or bitumen filling in two panel etc complete all as specified and as directed. |
| 104 | Demolition of reinforced concrete of any description and in any position not otherwise specifically provided for including reinforcement cut as required to facilitate demolition complete all as specified and directed |
| 105 | M&L Rolled steel sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connectiong plates complete including cutting, grinding, welding etc Fe-290 (Gde E-165) as required complete all as specified and directed.Note : The Qty considered is tentative and it should be get approved from CEA before execution of the work. |
| 106 | S&F powder coated anodised Aluminium aloy sections windows with frame side hung/openable shutters duly fitted with neoprene beading, cleats,glazing clips,hinges shutters glass panes 4.80 mm nominal thickness , aluminium alloy handles etc. as shown in TD Drwg No -CEJZ-/12 sheet No-1/2 complete all as specified and directed. |
| 107 | S&F Mirror cabinet PVC/fiber of size 500x 400 with mirror complete all as specified and as directed. ( Make -cat-556 of prayag or eqivalent ) |
| 108 | S&F 15mm dia brass CP wall mixer with L bend for mixing hot and cold water screwed down for iron pipe and fixed in repairs complete all as specified and directed. |
| 109 | S&F 20 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed complete all as specified and directed. |
| 110 | S&F of 75 mm PVC (SWR) branch piece, single (single Y) equal or unequal or with parallel branches complete alla specied and directed. |
| 111 | S&F of 110 mm 75 mm PVC (SWR) branch piece, single (single Y) equal or unequal or with parallel branches complete alla specied and directed. |
| 112 | M&L for Chequered cement concrete tiles 20cm x 20cm x 25 mm thick with white cement and pigment, jointed and pointed in neat cement slurry in floors on horizontal surfaces including 15mm thick screed bed cement mortar 1:6 complete all as specified and directed. |
| 113 | S&F Tee grid suspension system of size 600 mm x 600 mm type-1 made out of roll framed hot dipped galvanised steel zince coated of not less than 120 gm/Sqm, main runner 0.3 mm thick of section 24 mm x 33 mm crross runner 0.30 mm thick of section 24 mm x 25 mm, wall angle shall be 0.63 mm thick of section 24 mm x 24 mm grid shall be suspended by 4 mm dia adjustable quick fit hanger rod, system exposed portion shall be pre painted polyester coated in off whitee/white in colour complete with material, fixing, jointing etc., with Coloured textured designer ceiling board 4mm thick of size 595 x 595 mm fixing with screws/clips all as per manufacturers instructions and direction complete all as specified and directed. |
| 114 | Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.,) or insulation boards /slabs /blankets, any thickness, including cover fillets complete all as specified and directed. |
| 115 | Dismantling of plain or corrugated steel sheeting, any gauge,thickness,including Nainital or similar pattern roof coverings complete all as specified and directed. |
| 116 | Dismantling single layer Mangalore pattern or similar tiles in roofing complete all as specified |
| 117 | Dismantling timber scantling 40 Sqcm and over in section in any position in unframed work as in rafters, purlins etc complete all as specified and directed. |
| 118 | S&F in repairs 18 mm (± 0.7 mm) thick, solid PVC sheet one side prelam sheet for cupboard shutter of density 600 Kg/Cbm bent 900 and finish at all edges at level for making egdes at level for making edge lipping/bending or 0.5 mm thick PVC sheet lipping at 4 edges using bonding tape etc complete all as per direction of Engineer-in-Charge and manufacturer specification |
| 119 | S&F of MS auto hinges of crank 0 degree & 90 degree, fixed with screws to timber frame complete all as specified and as directed. |
| 120 | S&F of G Profile handle for kitchen cabinet/ Cubboard fixed to board complete all as specified and directed. |
| 121 | S&F of Telescopic channels suitable for 560 mm depth cabinets complete all as specified and as directed. |
| 122 | S&F of stainless steel accessories grade 202 (Make:- V-BOSS/ Olive- Silver accessries) as mentioned below complete all as specified and as directed:- |
| 123 | (a) Plain basket pull out.(480x500 x200 mm) |
| 124 | (b) Cutlery pull out.(480x500 x100 mm) |
| 125 | (c) Cup & Saucer pull out (480x500 x100 mm) |
| 126 | (d) Plate trolly (480x500 x200 mm) |
| 127 | S&F Pre- painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified as specified |
| 128 | M&L for 75 mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed. |
| 129 | M& L for PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed. |
| 130 | M&L for post construction anti termite treatment Along the external wall or at the junction of floor and wall using ATT chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc complete all as specified and directed. |
| 131 | M&L for post construction anti termite treatment of soil under existing floors using ATT emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and directed. |
| 132 | M&L for Treating the soil under plinth protection / floor at the rate of 5 litres of ATT chemical emulsion per square metre of surface area complete all as specified and directed. |
| 133 | Material and labour for Mild Steel TMT bars 10 mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia, or securing with clips FE 410 Gde complete all as specified and directed. |
| 134 | Material & Labour for applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed. |
| 135 | Complete removal of existing treatment and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm including preparation of surface complete all as specified and directed. |
| 136 | Taking down copper/aluminium point wiring ( light, fan, socket or power) complete,incl fixtures and fittings like swithes, ceiling rose, pendant, regulator, sockets, light fitting ( Mirror light,Bulk head,LED Panel 2''x2'',security light,wall fitting,down light, Flood light,post top lantern) etc. removing materials for taking credit and making good disturbed surfaces of walls, floors, etc with cement plaster, putty and paint to match with the existing surface complete all as specified and directed. |
| 137 | M&L for modular Point wiring with 1.5 Sqmm FRLS insulated, unsheathed, multistranded, 1100 Volts grade copper conductor cable single core conforming to IS:694 along with one run of 1.5 Sqmm FRLS insulated copper conductor cable green in colour for continuous earthing drawn through and including medium grade rigid PVC conduit conforming to IS:9537 (Pt-III) and its all accessories/junction boxes/ inspection covers etc of suitable size but not less than 20mm (OD), concealed in wall/ floor etc including provision of pressed steel terminal box of thickness not less than 18 SWG / with earth dolly of suitable size concealed in wall and covered with 3 mm thick phenolic laminated hylam sheet fixed with brass/GI screws for mounting switches, sockets, fan regulator, etc. / modular metal flush box covered with modular frame plate with cover of any size as per site requirement for mounting modular switches, modular sockets, modular fan regulator etc complete all as specified and directed for the following points:- |
| 138 | (a) One light / ceiling fan / exhaust fan / call bell point controlled by one switch |
| 139 | (b) One light point controlled by one, two way switch 6 Amps |
| 140 | (c) One socket outlet 6 Amp controlled by one switch on the same board with other switches. |
| 141 | (d) One socket outlet 6 Amp controlled by one switch on indepdendent board. |
| 142 | All as per item No.135.00 above but using 2.5 sq mm single core copper conductor FRLSH cable of multistranded PVC insulated unsheathed 1100 volts grade for 16 Amps switch socket cobmination point including necessary running of 2.5 sq mm copper conductor FRLSH cable of multistranded PVC insulated unsheathed as earth continuity conductor along with wiring and connecting to the common eath dolly. |
| 143 | S&F modular switch one way 6 Amp 1 module all as approved complete all as specified and directed. |
| 144 | S&F modular switch one way 16 Amp 1 module all as approved complete all as specified and directed. |
| 145 | S&F modular switch two way 6 Amp 1 module all as approved complete all as specified and directed. |
| 146 | S&F modular bell push, 6 Amp, 1 module complete all as specified and directed. |
| 147 | S&F bell multi music type, AC, 240 volts complete complete all as specified and directed. |
| 148 | S&F modular socket 16 Amp - 3 pin combined 2 module all as approved complete all as specified and directed. |
| 149 | S&F modular socket 6 Amp 3 pin , 2 module all as approved complete all as specified and directed. |
| 150 | S&F modular hum free electronic step fan regulator, suitable for BLDC fan, 2 module all as approved complete all as specified and directed. |
| 151 | Supply and fixing in replacement ceiling rose in poly carbonate 3 terminal brass, flush type 6 Amps, 220 volts AC, ISI marked, fixing on 3 mm thick sunmica hylum plastic laminated round sheet 75mm dia complete all as specified and directed. |
| 152 | Supply and fixing in replacement of modular MCB protected plug and socket board in sheet steel enclosure with 25 Amp rated mini MCB and 25 Amp rated 3 pin plug, 240 V, 50 Hz complete including cutting the wall surfaces for flush mounting of socket board including taking down existing unserviceable plug & socket board of any description and making good with cement plaster, putty and paint to match with the existing surface all as specified and directed. |
| 153 | Taking down carefully copper/aluminium Sub main wiring of any size from surface/concealed /existing conduit of any height and removing materials at site and making good disturbed surfaces of walls, floors roofs etc complete all as specified and directed. |
| 154 | S & F for in repairs sub main wiring with two runs of PVC insulated but unsheathed multi stranded copper conductor FRLSH cable 1100 volt grade of size 6 Sqmm and one run of 6 Sqmm single core PVC insulated but unsheathed multi stranded copper conductor FRLSH cable (Phase-Red, Neutral-Black, Earth-Green) 1100 volt grade as earth lead drawn through in and including non metallic PVC conduit of size 25 mm dia (external) with wall thickness not less than 1.8 mm, ISI marked concealed in wall including accessories like bends, tees junction boxes, etc fixed in wall or ceiling etccomplete all as specified and directed. NOTE:- Two runs of cable with one run of earth wire cable incuding one run of PVC conduit will be measured as one length including making good the disturbed surfaces. |
| 155 | All as per Item No 148.00 above but of size 2 runs x 4 sqmm (Ph & N) + 1run x 4 sqmm(earth wire)NOTE:- Two runs of cable with one run of earth wire cable incuding one run of PVC conduit will be measured as one length including making good the disturbed surfaces. |
| 156 | All as per Item No 148.00 above but of size 4runs x 6 sqmm (Ph & N) + 1run x 6 sqmm (earth wire)NOTE:- Four runs of cable with one run of earth wire cable incuding one run of PVC conduit will be measured as one length including making good the disturbed surfaces. |
| 157 | Supply and fixing in replacement of old unserviceable LED tube light fitting Integral slim LED batten 20 watts with polycarbonate housing and diffuser internally prewired complete with all accessories and including connecting up with PVC insulated and PVC sheathed twisted three core flexible copper wire of 0.5 sqmm from ceiling rose to connector of fitting complete all as specified and directed. |
| 158 | Supply and fixing in replacement of old unserviceable LED mirror light light fitting Integral slim LED batten Integral 9 / 10 watts of 2 feet long internally prewired complete with all accessories and including connecting up with PVC insulated and PVC sheathed twisted two core wire of suitable size complete all as specified and directed. |
| 159 | Supply and fixing in replacement Decorative wall light fitting, made out of polycarbonate suitable for B-22 base LED lamp including 9/10 watts LED lamp, full white of approved model fixed on wall and making electrical connection with PVC insulated and PVC sheathed twisted two core wire of suitable size complete all as specified and directed. |
| 160 | Supply and fixing in replacement of LED bulkhead luminaire 10 watt environmental friendly, ultra modern, energy saving, surface mounted, decorative oval bulk head edge-lit with diffuser, including making electrical connection with PVC insulated and PVC sheathed twisted two core wire of suitable size complete all as specified and directed. |
| 161 | Taking down MCB distribution boards with incoming and outgoing controls any make, any capacity after disconnecting complete as directed. |
| 162 | Supply and fixing in replacement of MCB distribution board, SPN, 8 way, 230 V, Single phase, AC in sheet steel powder painted enclosure double door type with minimum IP 43 degree of protection with built in copper bus bar, neutral link and earth link complete including cutting the wall surfaces for flush mounting of DB and making good with cement plaster, putty and paint to match with the existing surface complete all as specified and directed. Note: MCBs shall be measured and paid separately. |
| 163 | Supply and fixing in replacement of MCB distribution board, TPN, 4 way, 415 V, 3 phase, AC in sheet steel powder painted enclosure double door type with minimum IP 43 degree of protection with built in copper bus bar, neutral link and earth link complete including cutting the wall surfaces for flush mounting of DB and making good with cement plaster, putty and paint to match with the existing surface complete all as specified and directed. Note: MCBs shall be measured and paid separately. |
| 164 | Supply and fixing in replacement of MCCB / MCB distribution board, Vertical TPN, 4 way, 415 V, 3 phase, AC with MCCB as incomer and MCBs as outgoing in sheet steel powder painted enclosure double door type with minimum IP 43 degree of protection with built in copper bus bar, neutral link and earth link complete including cutting the wall surfaces for flush mounting of DB and making good with cement plaster, putty and paint to match with the existing surface complete all as specified and directed. Note: MCCB / MCBs shall be measured and paid separately. |
| 165 | Supply and fixing of MCCB 160 Amp, 16 KA, 4 Pole, 415 Volt, 50 Hz with fixed thermal magnetic release fixed in Vertical TPN complete all as specified and directed. |
| 166 | Supply and fixing in replacement of MCB 100 Amp, 10 KA, TPN, 'C' curve, 415 Volt, 50 Hz complete all as specified and directed. |
| 167 | Supply and fixing in replacement of MCB 6 - 32 Amp, 10 KA, single Pole, 'C' curve, 240 Volt, 50 Hz complete all as specified and directed. |
| 168 | Supply and fixing in replacement of MCB 40 Amp, 10 KA, SPN, 'C' curve, 240 Volt, 50 Hz complete all as specified and directed. |
| 169 | Taking down Ceiling Fan of any make, type and sweep by disconnecting Electric Connection and deposit to MES store complete all as specified and directed. |
| 170 | Supply and fixing ceiling fans complete with blades, down rods, fan remote and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) including electrical connections from ceiling rose to fan teriminal complete all as specified and as directed. |
| 171 | Supply and fixing in replacement of ventilating / PVC exhaust fans fancy square type 250mm sweep with plastic fiber body heavy duty 230 Volt AC, single phase complete with plastic louvers and including making suitable size of holes in wall for fixing the fan including making electrical connection with ceiling rose including taking down existing unserviceable ventilating fan of any description complete all as specified and directed. |
| 172 | S&F of TV co-axial modular socket 1 module as approved complete all as specified and as directed |
| 173 | S&F of telephone socket double RJ-11, 1 module as approved complete all as specified and as directed |
| 174 | M&L for co-axial TV cable drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories as required complete all as specified and as directed |
| 175 | M&L for PVC insulated unarmoured telephone cable for indoor applications 0.5 mm ATC 1 pair confirming to TEC specification G/WIR06/02 drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories as required complete all as specified and as directed |
| 176 | Taking down Exhaust Fan of any make, type and sweep by disconnecting Electric Connection and keep in safe coustody for repair/refixing complete as directed. |
| 177 | S&F in exhaust fan in kitchen of 300 mm sweep, with bird protector heavy duty motor, double ball bearings, single phase, 1400 rpm, powder coated metalic finish blade 3 Nos, 230V, 40 Watt, 50Hz, with louver shutter and mounting acessories including making openings for exhaust air through brick wall and making good by plastering rendering etc around the wall openings complete all as directed. (Note : Cost of suitable opening wall for fixing exhaust fan is deemed to be included in overall rate quoted). |
| 178 | Supply, Installed & fixing maintenance free earthing copper bonded steel earth rod of 10 feet long having diameter of 17.2 mm with copper bonding thickness of 250 micron, UL listed, CPRI Tested at 25 KA fault current for one second and provided with universal clamp made of SS earth enhancing compound shall be of 50 kg/pit (resistivity is less than 0.12 Ohm meter). The above arrangements shall be provided with heavy duty earth poly plastic pit cover of 4000 kg load bearing capacity (Size: 270 x 240 x 200mm) and FRLS insulated copper conductor of size 6 sqmm, single core cable drawn through and including medium grade rigid PVC conduit upto 7 mtr inclulding cutting and chases on wall / floor and making good using PCC work complete all as specified and directed.Note :- 6 sqmm, single core copper wire of lenght 6 RM as continuity conductor is including in quote rate. |
| 179 | Supply, installation , test and commisioning of Electric Chimney 900mm width & air flow capacity 1200 Cum/Hr including making hole in wall for exhaust pipe and providing required lenght pipe of suitable dimension from chimney to outside of kitchen into atmosphere and smooth the wall surface complete all as specified and directed with following features: (1) Touch and motion sensor control(2) Brushless DC motor, 9 speed control (3) Heat Autoclean Technology(4) Filterless Chimney - No need to clean or change filters (5) SS Oil Collector Tray (6) Energy Saving 2x1.5 W LED lights (7) Stir fry option for extracting fumes, Aeration for keeping the kitchen fresh (8) Metal Housing |
| 180 | Supply and fixing in replacement of LED street /security light fitting 30 watts with high efficiency long life LEDs with In-built electronic driver complete housed in pressure die-cast aluminium housing covered with polycarbonate cover with IP66 degree of protection including GI pipe bracket made up of 42 mm dia medium grade GI pipe of length 1.00 m bent to required shape and fixing on walls with suitable MS clamps (02 Nos) made up of 25 mm x 4 mm MS flat, nuts, bolts and washers and provision of 3 core PVC insulated and PVC sheathed twisted three core flexible copper wire of 0.5 sqmm from ceiling rose to connector of fitting complete all as specified. |
| 181 | Supply, laying and testing cable XLPE insulated screened PVC bedded, galvanized seel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 16 Sqmm 4 core including taking down of old unserviceable cable complete all as specified and directed. |
| 182 | Supply, laying and testing cable XLPE insulated screened PVC bedded, galvanized seel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 25 Sqmm 4 core including taking down of old unserviceable cable complete all as specified and directed. |
| 183 | Supply, laying and testing cable XLPE insulated screened PVC bedded, galvanized seel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 50sqmm 3 1/2 core including taking down of old unserviceable cable complete all as specified and directed. |
| 184 | Material and labour for Double wall corrugated HDPE pipe, ISI marked of outer dia 50mm, inner dia 38mm with smooth internal and profiled external surface, non-pressure type, laid in trenches /floors /duct or fixed on walls /pole including all connections, accessories like socket, couplers, bends, etc for protection of LT cable XLPE grade 1100 volts complete all as specified and directed. |
| 185 | Excavation in trenches in soft/loose soil not exceeding 1.5 m wide and not exc. 1.5 mtr deep for laying of cables and getting out any type of soil complete all as specified and directed. |
| 186 | Returning filling including spreading, levelling, watering and well ramming in layers not exceeding 25 cms thick in trenches complete all as specified and directed. |
| 187 | Removing excavated material not exc 50m and depositing where directed at a level not exc 1.5m above the starting point complete all as specified and directed. |
| 188 | Taking up or down existing unserviceable mild steel water tubing and connections 20 mm dia, any grade, of any description or in any position including fittings & removing to store complete all as specified and directed |
| 189 | Supply, fixing & laying GI tubing of 20 mm bore, medium grade with both end threaded in any length including cutting threading connection in new or old position including provision of all type of GI fitttings for laid in trenches/wall/ceilling/floor complete all as specified and directed. |
| 190 | M&L for drilling/boring and tapping on existing CI/GI pipe pipe 80mm to 300mm dia size for branch connections of 15mm to 50mm dia by fixing of MS clamp of size 50 X 40 mm cut to length and bent to shape, drilled and welded with GI socket of suitable size including rubber packing, nut, bolt and washer etc. and testing complete all as specified and directed. |
| 191 | Supply and fixing of Gun-metal, globe or gate valves, with iron wheel head , screwed both ends for iron pipe of size 50 mm dia pipe including all fittings and including taking down of old unserviceable valves complete and all as specified and directed. |
| 192 | Supply and fixing of electric water heater ,storage type steel body with glass lined inner tank and heating element up to 2 KW capacity 25 litre, BEE 5 star rated complete with all accessories such as safety valve, thermostate, NRV, connection pipe etc., including all water connection and fixing on wall with suitable MS tower/anchor bolts, grouted to wall complete all as specified and as directed. |
| 193 | NOTE FOR SCHEDUL OF CREDIT Rs (-) 2544375.00 AMOUNT DEDUCT FROM TOTAL QUOTED AMOUNT AT TIME OF ACCPTANCE OF TENDER. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 29, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 27, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 11 daysSep 03, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 18 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender