Tender for Tender for Painting, Installation Of Swings And Other Repair Work In Bhomiya Nagar Park In Ward No. 22 Of Vidyadhar Nagar Zone.
Tender Value
44.93 Lakhs
Estimated cost
Bid Submission
08 Aug 2026
7 days left
EMD
89860
Bank guarantee accepted
Document Fee
590
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jaipur → Rajasthan
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Painting, Installation Of Swings And Other Repair Work In Bhomiya Nagar Park In Ward No. 22 Of Vidyadhar Nagar Zone.
BOQ
| Sl. No. | Item Description |
| 1 | (4.2.1)Earth work in excavation for roadway, including trimming bottom and side slopes in accordance with requirement of line, grades and cross sections, including disposal of surplus material with all lift and lead upto 1000 metre as per MoRT&H specification clause 301. In all type of soil |
| 2 | (1.1.1)Carriage of Materials by mechanical transport including loading, unloading and stacking :: Earth 10 KM |
| 3 | (25.1.1)Random rubble masonry with hard stone in foundation and plinth : Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 4 | (24.4.1)Brick work with FPS bricks of class designation 75 in superstructure above plinth level upto two stories in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand) With FPS bricks. |
| 5 | (21.1.2)Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level : 1:1½:3 (1 Cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size). |
| 6 | (21.1.7)Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level : 1:4:8 (1 Cement : 4 fine/ coarse sand : 8 graded stone aggregate 40 mm nominal size). |
| 7 | (32.1.2)Cement plastering including T&P, scaffolding, material and complete labour, including cost of water, curing, racking of joints etc. with 12 mm cement plaster of mix : including Providing /mixing of synthetic fibers compulsorily complying with IS 16481:2022 of 06 mm/12 mm length to be mixed @ 0.25% by weight of Cement i.e. 125 gms per 50 kg Cement up to 900 gms per cum of Concrete/ mortar 1:6 (1 cement : 6 fine/ coarse sand) |
| 8 | (29.26.2)Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. |
| 9 | (32.15)Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete |
| 10 | (32.35.1)Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/ 10 sqm). |
| 11 | (32.51.1)Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture. |
| 12 | (9.2)Providing and laying rolled cement concrete mix of M-10 base course with coarse and fine aggregate conforming to IS:383, the size of coarse aggregate not exceeding 25 mm with minimum aggregate cement ratio 15:1 and minimum cement content of 200 kg/cum, aggregate gradation to be as per table 600-4 after blending, mixing in batching plant at optimum moisture content, transporting to site, laying with a paver with electronic sensor, compacting with 8-10 tonnes smooth wheeled vibratory roller to achieve the designed flexural strength, finishing and curing complete as per clause 603, 112 of MoRT&H specification including all material, labour, machinery, lighting, guarding and maintenance of diversion. |
| 13 | (9.11)Providing and fixing of 60mm thick precast cement concrete interlocking paver block casted with rubber moulds in approved reflective colour and design having minimum compressive strength of 300 kg/ sq cm. The CC paving blocks be laid on average 50mm thick bed of coarse sand and the joint is to be filled with fine sand. Laying procedure on compacted sub-base as defined. Complete job is to be executed as per the instruction of Engineer in-charge. The rates to be inclusive of all lead & Lifts etc. complete as perspecifications. |
| 14 | (10.1)Providing and fixing precast cement concrete M-20 grade (Using mechanical Concrete Mixer) kerb stone top and bottom width 115 and 165 mm respectively, 250 mm high on 150 mm thick PCC M-10 grade foundation as per design, including fixing at site as per clause 408 of MoRT&H Specification including all material, labour, machinery, lighting, guarding and maintenance of diversion |
| 15 | (30.21.1)Chequered precast cement concrete tiles 22 mm thick in footpath & courtyard jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing and cleaning etc. complete on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand).Light shade using white cement. |
| 16 | (39.48)Supplying, erecting and fixing in position specified precast RCC bench made of RCC grade M-30 consisting of 2 Nos. “L” shaped base support of thickness 100 mm back height 1000mm, front height 450 mm, base width 420mm and 5 Nos. RCC planks of size of 1500x100 x 50 mm and 1 Nos RCC planks of 150x200x50mm including joining all parts with galvanised nuts and bolts of suitable size. All bolts to be sealed after assembly with nice finish and appearance and level complete in all respect as per direction of engineer in-charge. Every bench should have a manufacturer’s logo of appropriate size Engraved at suitable place. |
| 17 | Providing and Fixing ROTO MPS of size area 22*16*12 feet, main frame manufactured with 75 mm OD pipe b class make TATA company pipe 31&25 mm OD pipe used,all slide are roto lidpe sllde are used, all nut bolts are galvanised. one towet used 14 feet height, one hexagonal tower (ph:5ft) with square and hexagonal decks. one roto lldpe premium spider shape canopy, one small roto lldpe butterfly canopy, one roto lldpe minion canopy, one roto llpde flower canopy, one roto lldpe spiral tube slide with safety gate (ph:5feet), one roto lldpe premium multicolour slide (PH:7feet), one roto lldpe multicolour straight slide with safety gate (PH:7feet), one roto abacus gril, one giraffic grills, two window grills, one lldpe sitting bench, two FRP staircase for better gripping and durability.All equipments should be paint by 2 layre of P.U. paint in multicolour or oven baked powder coated which ever is feasible and possible.All work and joint of pipe, nut should be in proper joint and finishing. All work should be done in engg. incharge. |
| 18 | DeluxeSlide:Deluxe Slide chute is made from stainless steel (SS) of 304 grade swith 16 SWG sheet.The structure comprises of 20 mm NB and 25 mm NB 'B' Class G.I. pipe. The centre support is made in 80 mm NB 'B' Class G.I. pipe and 15 mm NB G.I. pipe.The ladder cum railing is made up of 20 mm NB and 25 mm NB 'B' Class GI pipe. The platform is made up of 14 SWGA luminium sheet swith an tiskid for firm foot grip.There are train gular steps of 16 SWG sheets. The chute has its end such as it causes safe landing of the child.The pipe sare powder coated to avoid rusting. |
| 19 | FRP wave slide :Providing and Fixing of FRP wave slide its required area 4.6 mtr x 0.9 mtr platform height should be 5' Ground Level and should be made by 32 mm NB and 25 NB and 20 mm NB pipe MS pipe.Slide length10' all components paint by PU paint in multi colours. |
| 20 | CROSS TRAINERProviding and fixing of Cross trainer of size not less than 1140mm (Length) x 625mm (Width) x 1750mm. (Height), to enhance the mobility of upper and lower limbs and improve the flexibility of joints. The main structure frame shall be made from G.I. pipe minimum of 80NB “C” class welded with M.S. round base plate at least Ø250 mm & 10mm thick. The Handle Frame shall be made up of at least 25NB “C” Class G.I. Pipe. The footrests shall be made from LLDPE/Aluminum casting material of size not less than 130 mm X 310mmX5mm thickness and mounted on M.S. Plate of Size 130mmx310mmx3mm thick. High tensile steel with galvanized nuts and bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powders of Ackzonoble/ Berger/ Nerolac Paints with 60 to 70 Micron thicknesses complete in all respect including fixing the M.S. holdfast in cement concrete to hold the whole structure, under the directions of Engineer-in- charge to fulfill the functional requirement. |
| 21 | SEATED PULLERProviding and fixing of Seated Puller of size not less than 2400mm (Length) x 800mm (Width) x 2000mm. (Height), to enhance the strength of upper limbs and the muscles in chest and back and promote cardio-pulmonary function. The main structure frame shall be made from G.I. pipe minimum of 100NB “C” class welded with M.S. round base plate at least Ø250 mm & 10mm thick. The handle frame shall be minimum of 32NB “C” class G.I. pipe. The seat frame minimum of 50NB “C” class G.I. pipe, Closing Caps shall be made up of LLDPE/high quality Fiber reinforced Plastic material. High tensile steel with galvanized nuts & bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powders of Ackzonoble/ Berger/ Nerolac Paints with 60 to 70 micron thickness complete in all respect including fixing the M.S. holdfast in cement concrete to hold the whole structure, under the directions of Engineer-in-charge to fulfill the functional requirement. |
| 22 | CHEST PRESSProviding and fixing of Chest Press of size not less than 2200mm (Length) x 800mm (Width) x 2000mm. (Height), to enhance the strength of upper limbs and the muscles in chest & back and promote cardio pulmonary function. The main structure frame shall be made from G.I. pipe minimum of 100NB “C” class welded with M.S. round base plate at least Ø250 mm & 10mm thick. The handle frame shall be made up from at least 32NB “C” class G.I. pipe. The seats and Back rests to be fitted on the outer frames shall be made up of M.S. Sheet of size not less than 330mm X 300 mmX2mm thickness. Closing Caps shall be made up of LLDPE/high quality Fiber reinforced Plastic material. High tensile steel with galvanized nuts & bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powders from Ackzonoble/ Berger/ Nerolac Paints with 60 to 70 micron thickness complete in all respect including fixing the M.S. holdfast in cement concrete to hold the whole structure, under the directions of Engineer-in-charge to fulfill the functional requirement. |
| 23 | STANDING SEATING TWISTERProviding and fixing of Seating & Standing Twister of size not less than 1700mm (Length) x 540mm (Width) x 1250mm. (Height), to enhance flexibility of waist. Suitable for people of different ages except children. The main structure frame shall be made from G.I. pipe minimum of 100NB “C” class welded with M.S. round base plate at least Ø250 mm & 10mm thick. The bottom frame of the Seating & Standing twister be at least of 32 NB, 50 NB, and 25 NB shall be made from “C” class G.I. pipe. The handle frame of Seating & Standing twister of minimum 25 NB & Foot resting frame of seating side shall be made from “C” class G.I. pipe minimum of 25mm NB. The Twister plate to be fitted on the bottom frame shall be made up of M.S. Round Plate of minimum size 250 mm diameters and 10mm thickness. Closing Caps shall be made up of high quality LLDPE/Fiber reinforced Plastic material. High tensile steel with galvanized nuts & bolts shall be used for assembly. The powder coating shall be done by Pure Polyester powder of Ackzonoble/ Berger/ Nerolac Paint with 60 to 70 micron thickness complete in all respect including fixing the M.S. holdfast in cement concrete to hold the whole structure, under the directions of Engineer-in- charge to fulfill the functional requirement. |
| 24 | SURFING BOARDProviding and fixing of Surfing Board of size not less than 1150mm (Length) x 900mm (Width) x 1400mm (Height), to build up the muscle groups of the waist, enhance the body coordination and flexibility. The main structure frame shall be made from G.I. pipe minimum of 100NB “C” class welded with M.S. round base plate at least Ø250 mm & 10mm thick. The footrests shall be made from high quality LLDPE/fiber reinforced plastic material. High tensile steel with galvanized nut bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powder of Ackzonoble/ Berger/ Nerolac with minimum 60 to 70 micron thickness complete in all respect including fixing the M.S. holdfast in cement concrete to hold the whole structure, under the directions of Engineer-in-charge to fulfill the functional requirement. |
| 25 | SIT UP BOARD DOUBLEProviding and fixing of Sit up Board double of size not less than 1580mm (Length) x 1400mm (Width) x 680mm (Height), to enhance the flexibility of whole body. The main structure frame shall be made from G.I. pipe minimum of 100NB “C” class welded with M.S. round base plate at least Ø250 mm & 10mm thick. The remaining frame of the sit up board minimum of 32mm NB shall be made from “C” class GI pipe. The powder coating shall be done with Pure Polyester powder Ackzonoble/ Berger/ Nerolac Paints with 60 to 70 micron thickness complete in all respect including fixing the M.S. holdfast in cement concrete to hold the whole structure, under the directions of Engineer-in-charge to fulfill the functional requirement. |
| 26 | LEG PRESS : Area :- 0.40x1.77 MtrSafe Area :- Providing and the center pThe bottom support thickness is welded the remaining outer frame pipe. the foundation used for Ǿ 80mm made from \\"C\\" c & 10 mm thickness, 25mmx25mm. to join the c 3mm thicness is used. the seats are size 330mmx3mm and size 250mmx 200mm. the footrests is made 130mmx311.77 mtr.-1x2.38mtr. fixing leg press made from \\"B\\" class G.I. p pipe is of Ǿ 115mm made from \\"C\\" class G.I. of M.S. round plate of Ǿ 250mm & at bottom. is of Ǿ 40mm made from \\"C\\" class G.I. foundation fixing is consist of three equal class G.I. pipe, M.S. round p x 3mm M.S. angle. centre pipe & outer frame seamless pipe of thickness fitted on the outer frame is made up of FRP material of 300mm of thickness 3mm & M.S. plate of is used to support it. from aluminum casting material, i 10mm & 5mm thickness. pipe, made pipe and 250mm, 10mm items i.e. plate of Ǿ 250mm angle. Ǿ 120mm & thickness 5 support its sizes are the frame of footrests consists of Ǿ 32mm made from \\"C\\" class G.I. pipe. closing caps made from top quality FRP material which is of 2 mm thickness. the inner bushes is made from seamless pipe, its diameter is 60mm & 5mm thickness. the pins used in are made up of Ǿ 25 mm hardened bright bar, the bearings used are of \\"6205zz\\" permanent lubricated sealed bearing of reputed make (FAG/SKF). the handles used are of rubber grip. high tensile steel with galvanized nut bolts are used for assembly. the serclips used for assembly are of Ǿ 25 mm. the powder coat is done by poly urethane & exoxy powder with 60-to-70-micron thickness. |
| 27 | Providing & Fixing of Rotary Thrill Merry Go Round having require area of dia 1.5 meter & height of 1.0 meter from ground level . The center support is made with 60mm ODMS Apollo pipe . The heavy duty ball bearing 6312 of reputed make is attached for smooth rotation. The connecting support to seat shall be made with 32mm ODMS Apollo pipe . The Seat structure is made with 32mm & 25mm ODMS Apollo pipe. The 4 nos. of seats are made from fiber glass reinforce plastic of 3mm thick are attached with the structure . All Equipments should be paint by 2 layer of P.U.paint in multicolor or oven baked powder coated whichever is feasible and possible. |
| 28 | Providing & Fixing of circular swing with steel seat having require area 1.8 mtr. x 1.5 meter and height 2.1 mtr. from ground level. The leg support should be made by 48 mm odms pipe connected with 48 mm ODMS pipe. Top bar connected with outer frame of Circular swing made with 32 mm ODMS pipe & the outer frame is attached with seating structure made with 50 x 15mm ms rectangular pipe & the lower part should be made by 50 x 15mm rectangle pipe for foot rest. All Equipments should be paint by 2 layer of P.U.paint in multicolor or oven baked powder coated whichever is feasible and possible |
| 29 | Providing & Fixing of Climber A-Hexa having require area of 2.4 x 1.2 meter & height of 2.4 meter from ground level . The Vertical support should be made by 48mm ODMS pipe. The Globe outer frame should be made with 40mm ODMS & its inner frame made in 32mm ODMS pipe. Vertical support of spiral climber should be made with 40mm ODMS pipe & its steps made in 25mm ODMS pipe. All Equipments should be paint by 2 layer of P.U.paint in multicolor or oven baked powder coated whichever is feasible and possible. |
| 30 | Providing & Fixing of Toddler Swing having require area of 2.4 x 0.6 meter & height of 2.1 meter from ground level . The arch shape vertical support shall be made with 48mm ODMS Apollo pipe & the center support should be made in 58mm odms Apollo pipe . Between the horizontal bar there is heavy duty metal clamp with inbuilt bearing is attached to swing smoothly . The2 nos. bucket seats of the toddler swing are attached to a rubber coated GI Chain of 6mm . The bucket seats are of LLDPE material . All Equipments should be paint by 2 layer of P.U.paint in multicolor or oven baked powder coated whichever is feasible and possible. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 29, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 08, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 7 daysAug 10, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 9 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender