Tender For Special Repair To Bldg No Mes-45 (Mes Ib) At Shillong Cantt Under Ge Shillong
Tender Value
55.20 Lakhs
Estimated cost
Bid Submission
26 Aug 2026
16 days left
EMD
1.08 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
shillong → Meghalaya
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Special Repair To Bldg No Mes-45 (Mes Ib) At Shillong Cantt Under Ge Shillong
BOQ
| Sl. No. | Item Description |
| 1 | Taking down wooden chowkhats or frames with shutters (without taking off shutters from the frames) area exceeding 1.50 sqm but not exceeding 4.00 sqm each complete all as specified and as directed |
| 2 | Taking down old defective chowkhats with shutter (without taking off shutters from the frame) n.exc 1.5 sq.m each and removing away from site, complete all as specified and as directed. |
| 3 | Taking down old defective shutters of any description (wooden or aluminium) n. exc 1.0 sq.m each complete all as specified and as directed. |
| 4 | Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc. complete all as specified and directed. |
| 5 | Dismantling wooden fillets, rails, posts, rafters, purlins, etc. under 40 sqcm in section in unframed works, in any position complete all as specified and directed. |
| 6 | Demolition of cement concrete(unreinforced) in ground floors and paving not exceeding 15 cm thickness (below or above ground level) and complete all as specified and as directed. |
| 7 | Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) in any position below or above ground floors, not exceeding 15 cm in depth complete all as specified and as directed. |
| 8 | Dismantling of plain or corrugated steel sheeting, any gauge, thickness including any pattern roof coverings complete all as specified and as directed. |
| 9 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises |
| 10 | Dismantling of stone slabs and tiles of any description or thickness laid, bedded and pointed in any mortar in floors, aprons etc.complete as specified and directed |
| 11 | Dismantling of wall/ ceiling boards(fibre pulp insulation etc.) or insulations boards /slabs/blankets any thickness including cover fillets of any description including all snap grids and hanging arrangements complete all as specified. |
| 12 | Dismantling wooden boarding, any description, fixed in any position with nails complete all as specified and as directed. |
| 13 | Dismantling timber scantlings in unframed works, 40 sqcm and over in section, in any position |
| 14 | Excavating in post holes (or similar holes) each not exceeding 0.5 cum, getting out in soft/ loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering and removing surplus soil to a distance not exceeding 50 m and making good surface complete all as specified and as directed. |
| 15 | M & L for cement concrete in foundation, filling and mass concrete in M15(Nominal Mix) using 20 mm nominal size graded crushed stone aggregate complete all as specified and directed. |
| 16 | S & F for steel work of grade-3 as per IS 10748 in tubular trusses including special shaped washer etc. complete using ERW or HRIW welded tubes conforming to IS 1161: 2014 (Yst 240 Grade) complete all as specified and directed. |
| 17 | S & F of framework of seamless ceilling compresing of GI perimeter channel of 0.55 mm thick with two unequle flanges of 20 and 30mm and web of 27 mm fixed to surroinding wall using nylon sleeves and screwe at 450 mm centre to centre/intermediate chanell 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from sofit at approx 900 mm enter to centre with GI cleat and steel expension fasteren with and including ceiling section (n exc 1.2 mtr length) of 0.55 mm thickness having kurled web of 50 mm & flenge of 26 mm each with a lip of 10.50 mm fixed to intermediate channel with connecting clips acroos the intermediate channel at 457 mm centre to centre including hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed. |
| 18 | M& L for Providing and fixing 10mm thick plaster of paris ceiling (Gypsum anhydrous) to flat surface over 2nd class soft wood fillets, or metal frame work and reinforced with G.I. wire mesh (Fillets, metal frame work and G.I. wire mesh paid separately) complete all as specified and directed |
| 19 | S&F 10mm coloured PVC insulation panels with EPS stuck to 1mm plain PVC sheet suitably placed in false ceiling grid made of Aluminium/G.I./M.S. as per specification and drawing |
| 20 | M & L for structural timbers of group B, 2nd class hardwood as per IS 3629: 1986 in fillets, square, rectangular or triangular in section, clean sawn, secured with screw, area exceeding 13 sqcm but not exceeding 25 sqcm complete all as specified and as directed. |
| 21 | S&F 2nd class SW boarding 20mm thick fixed with nails in eaves board plained one side with butt joint including dismantling of old boarding complete all as directed. |
| 22 | M & L for structural timbers of group B, first or second choice as per IS 3629: 1986, clean sawn in scantlings and timber fixed complete all as specified and as directed. |
| 23 | S&F 2nd class hardwood plain, solid, straight chowkhats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints complete all as specified and as directed. |
| 24 | S&F 35 mm thk Flush door shutters solid core construction with block board core and ply wood face pannels commercial veneered on both faces complete alll as specified and directed. |
| 25 | S & F 2nd class HW 35mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. divided into squares (without sash bars ), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats as specified in SSR Part-I section 8 Clause 8.24 (a) complete all as specified and as directed. |
| 26 | S & F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and as directed. |
| 27 | S&F 18/19 mm thick block boards grade 1 quality exterior grade commercial type, water proof, termite proof fixed with screws to timber frame complete all as specified and directed. |
| 28 | M & L for 12 mm thick (7 ply) plywood, boiling water proof(BWP) Grade and Type BB as per IS 303: 1989 and IS 848: 2006; fixed with screws to timber frame work complete all as specified and as directed. |
| 29 | S & F 1.5 mm thick, type S (Standard type), wear index No. 3, Impact Index No. 2, Scratch Index No. 3, one side decorative, laminate as per IS 2046: 1995 of surfaces finish, colour and pattern as per approved, fixed with approved adhesive as per manufacturer's instructions complete all as specified and directed. |
| 30 | M & L for TELESCOPIC CHANNEL /Ball bearing drawer channel/catcher 500mm long including all necessary work complete fixed in position as directed |
| 31 | S&F W-hinges 75mm, Medium weight, Stainless Stell, complete all as specified and directed. |
| 32 | S&F W-hinges 125mm, Medium weight, Stainless Stell, complete all as specified and directed. |
| 33 | S & F 125 mm heavy weight( Type 1) mild steel butt hinges made out of cold reduced low carbon steel or hot rolled carbon steel as per IS 1341: 1992 complete all as specified and directed. |
| 34 | S & F brass barrel tower bolts with barrel of extruded sections of brass and rolled or down brass, 200 mm long, bright finish complete all as specified and directed. |
| 35 | S & F extruded brass handle, fabricated type polished, 250 mm size complete all as specified and directed. |
| 36 | S & F extruded aluminium alloy handle, fabricated type, 100 mm size, anodized to a bright natural, mat finish not be less than Grade AC 10 of IS 1868 : 1996 complete all as specified and as directed. |
| 37 | S&F Magnet catches for cupboard shutter, brass body and striking plate including letting in all as specified and as directed. |
| 38 | S & F mild steel continuous hinge, 30 mm nominal size, 1 mm thick, type IV as per IS 3818: 1992, bright finish and fixed to cupboard shutter complete all as specified and directed. |
| 39 | S & F brass sliding door bolts with sand-cast brass hasp, staple and fixing bolts or clips and rolled or drawn brass bolts (type-1) or Brass sliding door bits with diecast brass hasp, staple and fixing bolts or clips and rolled or drawn brass bolts (type -2), satin finish or polished, 300 mm long complete all as specified and directed. |
| 40 | S&F 6 lever Brass matte finish door handle of 200mm long with 1 x Mortice lock, 1 x striker plate, 1 x square shank including keys and all other necessary accessories fixed, colour and design as approved by GE complete. |
| 41 | S&F for 12mm thick toughned glass as in doors / partition or fixed including one hinged door, partion fixed with floors and walls, including one openable door with slef closing arrangement in bathroom fixed incl stainless steel floor spring with 2 Nos 400mm long stainless steel door handle with stainless steel connector to glass and similar work including cutting shape, drilling holes and fixing with single leg spider, ceiling/bottom SS 304 connectors wall to glass and glass to galss of required size, all necessary fittings upto all heights incl scaffolding complete all as specified and directed. |
| 42 | S & F factory made uPVC coloured Casement door with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. Comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality complete all as specified and directed. (Glass shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 43 | Providing and fixing factory made uPVC white colorSliding window Two track Area not exceeding 2.00 sqm each made of extruded profiles with wall thickness of 2.3mm (+- 0.2mm). Windowprofile with hollow section with multi chamber, Frame(60mm x 62mm). sash (42mm x 67mm). Sliding Interlock (One vertical length in each shutters) (45.5mm x 28mm). Glazing bead (24.5mmx 16mm) will he mitered cut and fusion welded at all corners,ncluding drilling of holes for fixing hardware and drainage of water etc.. making arrangement for fixingof hardware. EPDM gasket 1.2 + -0.2mm thickgalvanized steel frame (30mm x 21.5mm), Sash (30mm x 18mm), profile to be inserted in required profile,frame will be fixed to the wall with 8mm x 100mm long fasteners. Hardware : [Touch Lock of zinc alloyed(white powder coated), steel roller system including5mm thick glazing with selected quality glass,aluminum track on bottom rail for two track slidingframe, wool pine for Sliding sash and interlock.](Note: The unit rate quoted by contractor excludescost of glass and includes all other connectedaccessories. Net opening will be measured for payment purpose) |
| 44 | Providing and fixing factory made uPVC white colorSliding window Two track Area exceeding 2.00 sqm each made of extruded profiles with wall thickness of 2.3mm (+- 0.2mm). Windowprofile with hollow section with multi chamber, Frame(60mm x 62mm). sash (42mm x 67mm). Sliding Interlock (One vertical length in each shutters) (45.5mm x 28mm). Glazing bead (24.5mmx 16mm) will he mitered cut and fusion welded at all corners,ncluding drilling of holes for fixing hardware and drainage of water etc.. making arrangement for fixingof hardware. EPDM gasket 1.2 + -0.2mm thickgalvanized steel frame (30mm x 21.5mm), Sash (30mm x 18mm), profile to be inserted in required profile,frame will be fixed to the wall with 8mm x 100mm long fasteners. Hardware : [Touch Lock of zinc alloyed(white powder coated), steel roller system including5mm thick glazing with selected quality glass,aluminum track on bottom rail for two track slidingframe, wool pine for Sliding sash and interlock.](Note: The unit rate quoted by contractor excludescost of glass and includes all other connectedaccessories. Net opening will be measured for payment purpose) |
| 45 | Providing and fixing factory made uPVC white colourfixed window Area exceeding 1.00 sqm but not exceeding 2.00 sqm each made of extruded profiles with wallthickness of 2.3mm(+-0.2mm). Window profile withhollow section with multi chamber. Frame (60mm x58mm). T profile (Onevertical length in between twoshutters) (60mm x 74mm). Glazing bead (35mm x20mm) will be mitered cut and fusion welded at allcorners, including drilling of holes for fixinghardware and drainage of water etc. makingarrangement for fixing of hardware, EPDM gasket.1.2 +–0.2mm thick, galvanized steel Frame (28mm x21.5mm), T profile (27mm x 17 mrn) to be inserted inrequired profile, frame will be fixed to the wall with8mm x 100mm long fasteners- 5mm thick glazing withselected quality glass (Note: The unit rate quoted by contractor excludes costof glass and includes all other connected accessories Net opening will be measured for payment purpose.) |
| 46 | Providing and fixing factory made uPVC white colourfixed window Area exceeding 2.00 sqm each made of extruded profiles with wallthickness of 2.3mm(+-0.2mm). Window profile withhollow section with multi chamber. Frame (60mm x58mm). T profile (Onevertical length in between twoshutters) (60mm x 74mm). Glazing bead (35mm x20mm) will be mitered cut and fusion welded at allcorners, including drilling of holes for fixinghardware and drainage of water etc. makingarrangement for fixing of hardware, EPDM gasket.1.2 +–0.2mm thick, galvanized steel Frame (28mm x21.5mm), T profile (27mm x 17 mrn) to be inserted inrequired profile, frame will be fixed to the wall with8mm x 100mm long fasteners- 5mm thick glazing withselected quality glass (Note: The unit rate quoted by contractor excludes costof glass and includes all other connected accessories Net opening will be measured for payment purpose.) |
| 47 | Supply & fix sheet glass,8 mm thick and glazed fixed to ALUMINIUM frame not exceeding 0.5 Sqm in each pane complete all as specified and directed. |
| 48 | Supply & fix sheet glass 8 mm thick and glazed fixed to Al frame exceeding 0.5 Sqm in each pane complete all as specified and directed. |
| 49 | Supply & fix sheet glass 6 mm thick PLAIN/Black tinted and glazed fixed to metal/non metal exceeding 0.5 Sqm in each pane complete all as specified and directed. |
| 50 | Supply & fix sheet glass, ordinary quality, ground or obscured or frosted, 4.8 mm thick and glazed with oil putty or fixed with beads in square not exceeding 0.5 Sqm in each pane complete all as specified and directed. |
| 51 | M & L for precast cement concrete solid block masonry made using cement concrete M10 (Nominal Mix) using 20 mm nominal size graded crushed stone aggregate exceeding 10 cm in width and set in cement mortar (1:6) complete all as specified and as directed. |
| 52 | M & L for precast cement concrete solid block masonry n exc 10cm in width as per IS 2185 (part-1): 2005, masonry of grade C(5.0) with concrete M10 (Nominal Mix) using 20 mm nominal size graded crushed stone aggregate, and set in cement mortar (1:4) complete all as specified and directed. |
| 53 | M & L for pre-painted hot-dip aluminium-zinc alloy metallic coated corrugated steel sheet, any pattern corresponding to IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ150, 0.50 mm thick, of an approved colour and having yield strength of 550 MPa as in roof covering/ wall clading fixed with self tapping screws as specified including necessary scaffolding and safety measures at any floor complete all as specified and as directed. |
| 54 | M&L for pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour as approved by GE having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 55 | M&L for 10-12 mm thick premimum quality wooden laminate flooring, waterproof, AC4 grade with superior wear resistance, featuring MDF and HDF base materials, abrasion class standard, European flooring standards, waterproof certification of plank size 4' x 8' x 8mm including 2mm thick layer of foam for cushioing colour and design as approved by GE, complete all as specified and as directed |
| 56 | M & L for screed bed or bedding layer of mortar 20 mm thick in cement mortar 1:6 for laying floor finishes complete all as specified and as directed. |
| 57 | M & L for cement concrete M15 (Nominal Mix) using 20 mm nominal size graded crushed stone aggregate as in floor 40 mm thick finished even and fair complete all as specified and directed. |
| 58 | M & L for cement concrete M15 (Nominal Mix) using 20 mm nominal size graded crushed stone aggregate as in floor 25 mm thick finished even and fair complete all as specified and directed. |
| 59 | M&L for light shade vitrified ceramic tiles 10 mm thick (square / rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tile, laid over and including 15mm thick screed bed in CM 1:4, complete all as specified and as directed. |
| 60 | M & L for ceramic vitrified tiles, coloured ceramic floor tiles (group B Ia), 600 mm X 600 mm X 10 mm in skirting's/ vertical surfaces laid including 10 mm thick backing coat in cement mortar(1:4) set and jointed in neat cement slurry and pointed in epoxy mortar to match all as specified and directed. |
| 61 | M&L for Glazed ceramic tiles on vertical surface of size 450X 300X 7-8mm or 300x600x7-8mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match with shade of the tiles laid over and including 10mm thick rendering as backing coat in CM 1:4 with wire markings to receive tile over it, complete all as specified and as directed. |
| 62 | M&L 18-20mm thick black Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in over and including 15mm thick cement mortar (1:6) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including necessary dismantling of existing unserviceable one complete all as specified and directed. |
| 63 | M & L for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and as directed. |
| 64 | Taking down cement plaster, any description, on brick or stone walls, etc.including racking out joints, hacking for key, scrubbing down with water, etc. including removal of rubbish material away from site, complete all as specified and as directed. |
| 65 | Material and labour for plastering 10 mm thick on fair faces of brick work or concrete surfaces (on vertical surfaces) in cement mortar 1:6 finished even and fair without using extra cement complete all as specified and as directed. |
| 66 | Material and labour for plastering 15 mm thick (in two layers of 10mm and 5mm thk) on fair faces of brick wall or concrete surfaces in cement mortar 1:4 with water proofing compound as per manufacturer's printed instruction finished even and fair complete all as specified and directed.Note: (i) Water proofing compound shall be measured and paid for separately. (ii) The cost of scaffolding is included in this item. |
| 67 | Supply only integral water proofing compound complete all as specified and directed. |
| 68 | S & F 600 mm X 450 mm bevelled edge mirror of selected quality glass, mounted on 6 mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. |
| 69 | S&F vitreous china table top basin - white matt, kubix prime range of Jaguar of size 600x400x150mm including 32mm waste coupling with chromimum platted bottle trap complete all as specified and directed. |
| 70 | S & F sheet glass shelf assembly consisting of 5.50 mm thick glass sheet shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and as directed. |
| 71 | S&F glass corner shelf with bracket complete all as specified and as directed. |
| 72 | S&F single lever Basin Mixer with single lever tall boy with 155mm Extension body fixed Spout popup waste system with 600mm long Braided Hoses complete all as specified and as directed |
| 73 | S & F 15 mm nominal size, screw down stop valves/ angle cock, cast copper alloy body and body components with crutch handle, bright finished complete all as specified and as directed. |
| 74 | S & F in repairs 15 mm nominal size, nonrising spindle type fancy bib taps as per IS 8931: 1993, two ways in double control, made of cast brass including Knob, knob components, divertor & components, nickel-chromium plated finish complete all as specified and directed. |
| 75 | S & F of PVC (SWR) as per IS 13592: 2013 single socketed soil waste pipes in any length with rubber ring joints, 110 mm dia, laid in trenches complete all as specified and directed. |
| 76 | S & F of PVC bends without inspection door (any angle), 110 mm dia conforming to IS 14735: 1999 complete all as specified and directed. |
| 77 | M & L for cement concrete M15 (Nominal Mix) using 40 mm nominal size graded crushed stone aggregate 75 mm thick as in hardstanding/ path/ plinth protection complete all as specified and as directed. |
| 78 | S & F hot rolled medium and high tensile structural steel of grade E165 as per IS 15911: 2010 as in framed work such as grills, grating, etc., with ends of bars of shouldered and/or riveted, or forged into spikes, framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework water tanks and similar work complete all as specified and directed. |
| 79 | S & F for designer 25mm wide wooden beading for showcase or any wooden structure as approved including all necessary work complete. |
| 80 | S&F stainless steel slider channel for wooden cabinet or shutter with automatic soft close hinges and bracket including all necessary accessories fixed complete. |
| 81 | M & L for prefabricated glass fiber reinforced gypsum beads/ cornices architecturally crafted decorated 100 mm wide and fixing complete all as specified and as directed. |
| 82 | Material and labour for applying two coats of plastic emulsion paint over and including one coat of primer and 1mm putty white or tinted on new ceiling including preparation of surfaces complete all as specified and directed. |
| 83 | Preparation of newly or previously untreated steel surface of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed (spray painting). |
| 84 | M & L for preparation of new or previously untreated wood or wooden surfaces, of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 85 | Complete removal of existing treatment of wall and M & L for preparation of surface of wall and applying two coats of oil bound distemper over one coat of suitable primer over 1.5 mm thick wall care putty to match the surfaces complete all as specified and as directed |
| 86 | M & L for preparation of old decorated wood or wooden surfaces, of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed. |
| 87 | M&L for preparing old decorated plastered surfaces of walls by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salt and trading oil and greasy spots and applying two coats of exterior emulsion paint (Apex/Weather coat) white or tinted as approved complete all as specified and directed |
| 88 | M & L for preparation of newly plastered surface of wall and applying two coats of weather coat exterior paint over one coat of alkali resistance primer complete all as specified and as directed. |
| 89 | S&F half round PVC rain gutter of dia 180mm including clamps, bolts and nuts complete all as specified and as directed |
| 90 | Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as specified and as directed. Please Enable Macros to View BoQ information |
| 91 | Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as specified and as directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 29, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 26, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 16 daysAug 28, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 18 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender