Tender For Addition Alteration Of 01 X Bath Room At Bldg No P-26 (Otm Accn), P-01, Provn Of Parking Shed For Four Wheeler (10 X Vehs) At Bldg No P-73 & P-74, 01 X Single Toilet Bathroom In Mandir Area At Bldg No P-111 And 01 X Toilet In Wksp Area Under Ag
Tender Value
38 Lakhs
Estimated cost
Bid Submission
17 Aug 2026
7 days left
EMD
76000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Pathankot → Punjab
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Addition Alteration Of 01 X Bath Room At Bldg No P-26 (Otm Accn), P-01, Provn Of Parking Shed For Four Wheeler (10 X Vehs) At Bldg No P-73 & P-74, 01 X Single Toilet Bathroom In Mandir Area At Bldg No P-111 And 01 X Toilet In Wksp Area Under Age B/R-I Of Ge (N) Mamun
BOQ
| Sl. No. | Item Description |
| 1 | Taking down chowkhats or frames with shutters (without taking off shutters from the frames) n.exc 1.50 sqm each complete all as specified and directed. |
| 2 | Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exceeding 1.5 Sqm and n.exc 4 Sqm each complete all as specified and directed. |
| 3 | Taking down cement plaster on brick walls or stone walls of any description etc including raking out joints, hacking for key, scrubbing down with water etc, rubbish off the premises complete all as specified and directed. |
| 4 | Demolition of cement concrete (unreinforced) of any description and in any position not specifically provided for, complete all as specified and as directed. |
| 5 | Demolition of cement concrete (unreinforced) in ground floor and paving n.exc 15 cm thick (below or above ground level) and removal of rubbish beyond MOD land complete all as specified and directed. |
| 6 | Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for( reinforcement cut as required to facilitate demolition) and rubbish off the premises, complete all as specified and directed |
| 7 | Dismantling of brick work built in cement mortar including all quoins, arches, pillars etc and removal of debris/rubbish off the premises etc complete all as specified and directed. |
| 8 | Dismantiling old floor tile including cement mortar bedding and removal of debris out o premised complete all as specified and directed. |
| 9 | Dismantling floor, hearth or walls tilling and terrazo topping including cement mortar bedding ( but not backing), rubish off the premises complete all as specified and directed. |
| 10 | Taking up or down steel water tubing and connections including cleaning for refixing of pipe 15mm bore or removal to store complete all as specified and directed. |
| 11 | Taking up or down steel water tubing and connections including cleaning for refixing of pipe 20mm bore or removal to store complete all as specified and directed. |
| 12 | Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc complete all as specified and directed. |
| 13 | Hacking out old broken glass ( any thickness , size, quality, or description) from metal frame glazed with putty or fixed with beads/clips, rubbish off the premises complete all as specified and directed. |
| 14 | M&L for Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc., Brushing neat cement slurry with 3.0kg of cement per sq. meter complete all as specified and directed |
| 15 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified & directed. |
| 16 | Surface dressing n.exc (not exceeding) 30cm deep and averaging 15 cm deep and getting out in soft/loose soil, complete all as specified and directed. |
| 17 | Excavating in trenches n exc 1.5m wide and n exc 1.5m depth for foundation etc or for shafts, well, cesspits, manholes, pier holes, cable tranch, pole, drain etc n exc 10 sq m on plan and n exc 1.5m depth and getting out in soft/loose soil complete all as specified and directed. |
| 18 | Surface excavation not exc 30cm in depth and averaging 15 cm deep and getting out in soft/loose soil, complete all as specified and directed. |
| 19 | Excavation in post holes (or similar holes) each n.exc. 0.5 cum getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering and removing surplus soil to a distance not exceeding 50m, in soft/loose soil and making good surfaces, complete all as specified and directed. |
| 20 | M&L Plain cement concrete 1:4:8 type D2 using 40mm graded crushed stone aggregate as in sunken floors portion complete all as specified and directed. |
| 21 | PCC 1:3:6 type C-2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified. |
| 22 | Returning filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm thick complete all as specified and directed. |
| 23 | Removing excavated material n.exc. 50m and depositing where directed at a level n.exc. 1.5 m above the starting point, complete all as specified and directed. |
| 24 | Hard core of broken stone or boulders of guage n. exc 63mm but exc 100mm, deposited, spread and levelled in layers n. exc 15 cm thick, watered and rolled/rammed to a true surface, complete all as specified and directed. |
| 25 | M&L for Brick work with fly ash bricks (Old Size bricks), sub class'B' bricks straight or curved on plan exc 6 mtr mean radius built in CM 1:4 complete all as specified & directed. |
| 26 | Brick work with old servicable bricks retrieved from dismantling, straight or curved on plan exc 6 mtr mean radius built in CM 1:4 complete all as specified and directed. |
| 27 | Brick work with old servicable bricks retrieved from dismantling, straight or curved on plan exc 6 mtr mean radius built in CM 1:4 complete all as specified and directed. |
| 28 | M&L Brick work with fly ash bricks straight or curved on plan to any radius in half thick walls,built in CM 1:4 complete all as specified and directed. |
| 29 | Brick work with fly ash bricks (Old Size bricks) straight or curved on plan exc 6 mtr mean radius built in CM 1:6 complete all as specified and directed. |
| 30 | M&L for 15mm thick cement plaster on brick work or concrete surfaces, in cement mortar 1:6 in two layer of 10mm each and finishing top surfaces fair and even (top layer to be provided with WPC @ 2% by weight of cement) and smooth with using extra cement complete all as specified and as directed (WPC shall be measured & paid separately). |
| 31 | M&L for Rendering 10mm thick on fair faces of brick work/ concrete sruface in cement mortar (1:6), finished even and smooth without using extra cement complete all as specified and directed. |
| 32 | M&L for Rendering 5mm thick cement plaster on fair faces of brick work, concrete sruface in cement mortar (1:3) as in ceiling finished even and smooth without using extra cement complete all as specified and directed. |
| 33 | M&L for Rendering 15mm thick on fair faces of brick work, concrete sruface in cement mortar (1:4), finished even and smooth without using extra cement complete all as specified and directed.Note : (WPC will be measured and paid seperately) |
| 34 | M&L for rendering 15 mm thick cemet plster on fair faces of brick work or concrte surfaces in CM 1:4 in two layers (5mm finishing layer over 10mm base layer) finished even and surface without using extra cemen with WPC over finishing layer complete all as specified and directed.Note: WPC shall be measured and paid seperately) |
| 35 | M&L for rendering or plastering 10 mm thick in CM 1:3 in fascia / edging / ceiling of Chajjas, roof projections, drainge etc, making the edges in line, in true shape and finishing the surface without using extra cement complete all as specified and directed. |
| 36 | S&F Factory Made Solid PVC Moulded door Shutter With wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick prelam Moulded PVC Sheet on the front face & 2mm plain colour prelaminated PVC sheet on back face complete all as specified and directed. |
| 37 | S&F pressed steel frames for doors/windows of size size 105x60 mm (1.25mm thick MS sheet) with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, duly filling of cement concrete 1:3:6 type C-0 (using 12.50 mm graded crushed stone aggregate) to back of chowkhats and two coats of synthentic enamel paint complete all as specified and directed. |
| 38 | S&F Solid PVC door frame of size 50 x 47 mm made out of 5mm wood grain printed PVC sheet used instead of plain colour PVC sheet & edges shall be painted to match with printed sheet reinforced with MS square tube, supplying and fixing in opening as per specification and drawing complete all as specified and directed. |
| 39 | S&F 35mm thick factory made plain framed panelled shutters of 2nd class hard wood, one panels with lock rail and panel of 9mm thick BWP commercial ply or 12mm veneered particle board with commercial veneering on both face. The size of rail and stile as per IS-1003 (Part-I)(Larger size to be provided) Kiln seasoned and chemically pressure treated fitted to chowkats complete all as specified and directed. |
| 40 | M&L for preparation old steel or iron surfaces of any description over 10 cm width or girth and applying two coat of synthetic enamel paint complete all as specified and as directed. |
| 41 | M & L preparation of new wood or wood based surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified & directed. |
| 42 | M&L for preparation new steel or iron surfaces of any description over 10 cm width or girth and applying two coat of synthetic enamel paint complete all as specified and as directed. |
| 43 | M&L for two coats of cement base paint on newly plastered surface including preparation of new surface over a coat of cement primer on wall complete all as specified and as directed. |
| 44 | M&L for two coats of OBD on wall including preparation on new plastered surface complete all as specified and as directed. |
| 45 | S&F Box type Steel windows and ventilators comprised of tubular frame and shutters made out of 1.25mm thick MS steel tube factory made with double side shutters wire gauged shutter & glass glazed shutter (wire mesh and glass panes shall be measured and paid separately) with side hung shutters with steel handle and steel peg stay dovetailed or welded including 2 Nos tower bolts 150mm long for each leaf and 8mm square bar grills at spacing as shown on drg welded to FI frame work, including other fittings, hinges, handles, tarred hold fasts, PCC blocks (1:2:4 type 12.50mm graded crushed stone aggregate) including two coats of synthetic enamel paint over a shop coat of red oxide primer etc. all as shown on drg No CEPZ /TD-354/09 sheet 1/3 to 3/3 complete all as specified and directed. |
| 46 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 65x100 mm (double rebate) comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with properties of being termite/borer proof, water/ moisture proof and fire retardant, fixed in position with and including MS hold fast/lugs/SS dash fasteners of required dia and length complete all as specified and directed. Note: (i) For WPC solid door/window frames minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. (ii) Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made complete all as specified and directed. |
| 47 | Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately). |
| 48 | S&F Stainless steel wire cloth 0.71 mm nominal dia of wire and average width of aperture 1.40 mm fixed with tinned tacks, or Stainless steel wire staples complete all as specified & directed. |
| 49 | S&F 4mm thick sheet glass ordinary quality and glazing with oil putty or fixed with bead/glazing pins in squares not exc 0.50 Sqm in each pane including hacking out old broken glass complete all as specified and directed. |
| 50 | S&F in repair Stainless steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm fixed with tinned tacks, or galvanized wire staples complete all as specified & directed. |
| 51 | 4mm thick figured glass ordinary quality, and glazing with oil putty or fixed with bead/glazing pins in squares n.exc 0.50 Sqm in each pane, complete all as specified and directed. |
| 52 | S&F 100 mm size stainless steel butt hinges (as per sample) complete all as specified and directed. |
| 53 | S&F 100 mm size butt hinges (as per sample) medium weight, cold rolled mild steel complete all as specified and directed. |
| 54 | S&F 300 mm long aluminium alloy, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts complete all as specified and directed. |
| 55 | S&F aluminium anodized barrel tower bolts 200 mm of extruded section (as per sample) fixed complete all as specified and directed. |
| 56 | S&F 100 mm size aluminium alloy handles, febricated type extruded section (as per sample), complete all as specified and directed. |
| 57 | S&F 150 mm size aluminium alloy handles, febricated type extruded section (as per sample), complete all as specified and directed. |
| 58 | S&F 25mm curtain rails anodised aluminium alloy with brackets, end bulbs, fancy type, fixed in position (as per sample)complete all as specified and directed. |
| 59 | S&F Peg set of Six fixed with chromium plated brass screws and wooden and plastic cleats(min wt 190 gm) complete all as specified and directed. |
| 60 | S&F in repair 25mm bore mild steel powder coated, single curtain rod (walls thickness not less than 1mm) including fancy type PVC owder coated brackets, fenials etc (as per sample) suitable for single curtain rod, fixed in repair complete all as specified and directed. |
| 61 | M&L for preparation of new/ old wall surface, making surface clean, dry, free from any loose paint film, dirt, chalk, grease, fungus and algae etc and applying one coat of antifungal acrylic emulsion exterior weather proof paint complete all as specified and directed. |
| 62 | M&L for preparation of new plastered surface of walls and applying three coats of white wash complete all as specified and directed. |
| 63 | M&L for preparation of new plastered surface of ceiling and applying three coats of white wash complete all as specified and directed. |
| 64 | M&L for preparation of old plastered surface of walls and applying two coat of white wash complete all as specified & directed |
| 65 | M&L for preparation of old plastered ceiling surface and applying two coats of white wash complete all as specified and directed. |
| 66 | M&L for complete removal of old existing treatment including preparation of plaster/unplaster surfaces of walls, chajja, fascia etc and applying one coat of external wall care putty and two coat of exteior emulsion paint (weather coat) over a coat of primer any shade or colour complete all as specified and directed. |
| 67 | M&L for preparation of old surface after complete removal of existing treatement making surface smooth and applying two coats of cement base paint over a coat of alkali-resistant priming paint complete all as specified & directed. |
| 68 | M&L for preparation of old surface of wall complete removal of existing treatment and applying 2mm thick wall care putty over one coat of primer and making surface even and smooth and applying two coats of oil emulshion distemper complete all as specified & directed. |
| 69 | M&L for preparation of new plastered surface of external wall and chajjas, making surface smooth using sand paper, priming the surface with alkali resistance primer paint for external surface, applying one coat of external wall care putty and two coats of exterior emulsion (weather coat) paint complete all as specified & directed. |
| 70 | M&L for preparation of new plastered surface of external wall by applying 2mm thick wall care putty and making the surfaace smooth applying two coats of distemper oil emulsion over a coat of primer of new surface complete all as specified & directed. |
| 71 | M&L for PCC 1:2:4 Type B1 (using 20 mm graded crushed stone aggregate) as in cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, benching, copings, kneelers, apex stones, bed plates, kerbs , fillet, gola, water troughs and the like including weathering, slightly rounded or chamfered edges including necessary form wrok complete all as specified and directed |
| 72 | PCC type C-1, 1:3:6 (using 20mm graded crushed stone aggregate) as in plinth protection 75mm thick laid in slope finished even and fair including making joints not more than 2.5 m (or as directed) and at corner, filled with bitumen 85/25 and sand in ratio 1:2 by weight complete all as specified and directed. |
| 73 | 75mm thick PCC 1:4:8 Type D-2 (40 mm graded stone aggregate) as in sub-base of floors, sub-bases, floors, pavings etc, complete all as specified and directed. |
| 74 | M&L for 100mm thick PCC 1:2:4 type B2 (40mm graded crushed stone aggregate) as in sub floors, sub bases floors and pavings etc complete all as specified and directed. |
| 75 | M&L for 100mm thick cement concrete type D2 1:4:8 (40mm graded crushed stone aggregate) as in sub floors, sub bases floors and pavings etc complete all as specified and directed. |
| 76 | 25mm thick PCC 1:2:4, type B-0 (using 12.5 mm graded crused stone aggregate) as in floors to recieve floor finishes, complete all as specified. |
| 77 | 25mm thick PCC 1:2:4, type B-0 (using 12.5 mm graded crused stone aggregate) as in floors to recieve floor finishes, complete all as specified. |
| 78 | M&L PCC 1:2:4 type BI (using 20mm graded stone aggregate) as in coping, benching for manholes including necessary form work complete all as specified and directed. |
| 79 | M&L for Sand filling under floors or in foundation in layers n exc 40mm thick including watering and consolidation complete all as specified and directed. |
| 80 | Non skid ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc set and jointed (joint free) in neat cement slurry and pointed in coloured cement over 15mm thick screed bed or bedding layer of mortar in CM 1:4, complete all as specified and directed. |
| 81 | Non skid ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc set and jointed (joint free) in neat cement slurry and pointed in coloured cement over 15mm thick screed bed or bedding layer of mortar in CM 1:4, complete all as specified and directed. |
| 82 | M&L for 20-25mm thick machine cut kota stone slab flooring over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade,of the slab including rubbing and polishing and including 15 mm thick screed bed or bedding layer of mortar in CM 1:6, complete all as specified and as directed. |
| 83 | M&L for Machine cut kota stone slab flooring 20-25mm thick in riser of steps, skirting, dado and pillar over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade, mirror polished complete over and including 10 mm thick screed bed or bedding layer of mortar in CM 1:4 complete all as specified and as directed. |
| 84 | M&L for 80mm thickness M-40 grade Machine pressed precast concrete factory made paver block confirming to IS-15658-2006 (topping thickness not less than 5mm thick with white cement and colour pigment non fadable epoxy coating) complete all as specified & directed. |
| 85 | 15mm bore Steel water tubing, galvanised, \\"medium grade\\" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor, complete all as specified and directed. |
| 86 | Refixing of old steel tubing 15mm bore and connection in old or new position (walls, ceiling or floors etc.) with new all fittings short pieces, complete all as specified and directed. |
| 87 | 20mm bore Steel water tubing, galvanised, \\"medium grade\\" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor, complete all as specified and directed. |
| 88 | Refixing of old steel tubing 20mm bore and connection in old or new position (walls, ceiling or floors etc.) with new all fittings short pieces, complete all as specified and directed. |
| 89 | Cutting chases for concealed water tubing, making good to facing where required, pointing in CM 1:3, cutting n.exc. 10cm in girth, complete all as specified and directed. |
| 90 | S&F in repair 15mm bore bib tap fancy type chromium plated cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule (fixed in repairs),complete all as specified and directed. |
| 91 | 15mm bore stop valve/angel valve, chromium plated cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or union (fixed in repairs), complete all as specified and directed. |
| 92 | S&F 15mm bore dia stop valve concealed cast copper alloy (as per sample) chromium plated ISI marked with crutch or butter fly handles screwed down, screwed for iron pipe complete all as specified and directed. |
| 93 | 15mm bore pillar tap, copper alloy with capstan head, chromium plated screwed down high pressure, with or without lettered hot/cold with long screwed shanks and fly nuts screwed for iron pipe, complete all as specified and directed. |
| 94 | S&F in repair vitreous china, wash hand basin, white, flat back, of size 550mmx400mm with brackets including cutting for and pinning in ends of brackets, complete all as specified or erecting stand including 32mm full threaded waste coupling and 32mm PVC waste pipe, complete all as specified and directed. |
| 95 | S&F in repairs Vitreous china wash down water closet pan pedestal pattern , white (excluding supply of flushing cistern and flush pipes, but including fixing thereof), including making connections to trap, and to flush pipe incl plastic seat and cover ( As per sample ) with stainless steel or aluminised hinging device and health foucet/jet spray complete all as specified and directed. |
| 96 | S&F Vitreous china wash down water closet pan pedestal pattern , white (excluding supply of flushing cistern and flush pipes, but including fixing thereof), including making connections to trap, and to flush pipe incl plastic seat and cover ( As per sample ) with stainless steel or aluminised hinging device and health foucet/jet spray complete all as specified and directed. |
| 97 | S & F in repair vitreous china squatting pan water closet, orissa pattern, size 580x440mm white with integral foot rests (excluding flushing cistern and flush pipe) including cast iron 'P' or 'S' trap, front or back inlet and foot rests, any pattern including cement concrete bedding, complete all as specified and directed. |
| 98 | S&F in repairs vitreous china bowl urinal half stall type, white complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing flush pipe, grating and union for discharge pipe including providing and fixing of PTMT urinal spreader with 15mm dia pipe, complete all as specified and directed. |
| 99 | S&F Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe including Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed including old taking down complete all as specified & directed. |
| 100 | S&F Vitreous china wash hand basin, white flat back, size 550 x 400 mm (as per sample), including brackets, CP waste coupling and cutting for and pinning in ends of brackets or errecting stand including 32 mm dia waste pipe complete all as specified and directed. |
| 101 | PCC 1:5:10 type E-2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified. |
| 102 | PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified. |
| 103 | Rendering 15mm thick on brick work or concrete surfaces in CM 1:4 mixed with water proofing compound to sunken portion with proper slope towards outside, finishing cement concrete or brick work surface even and smooth using extra cement, provide 90 micron polythene film duly applying bitumen coating @ 3.00 Kg/Sqm complete all as specified and directed. Note: WPC shall measured and paid for separately. |
| 104 | S & F in repair 10 litre capacity PVC valveless, low level, synphonic action type, flushing cistern, with inlet, ball valve, float valve, handle including brackets including 32mm dia PVC flush pipe of suitable size and making necessary connections, complete all as specified and directed. |
| 105 | S & F 10 litre capacity PVC valveless, low level, synphonic action type, flushing cistern, with inlet, ball valve, float valve, handle including brackets including 32mm dia PVC flush pipe of suitable size and making necessary connections, complete all as specified and directed. |
| 106 | PVC connection 15mm size with PTMT nuts at both ends of length 450mm for hot and cold water, complete all as specified and directed. |
| 107 | 600 mm x 450 mm bevelled edge mirror of selected quality glass mounted on 6 mm thick AC building board or BWP commercial plywood and fixed to wooden plugs/PVC rawl plug with chromium plated brass screws and cup washers, complete all as specified and directed. |
| 108 | 600 mm x 1200 mm bevelled edge mirror of selected quality glass mounted on 6 mm thick AC building board or BWP commercial plywood and fixed to wooden plugs/PVC rawl plug with chromium plated brass screws and cup washers, complete all as specified and directed. |
| 109 | S&F in repair towel rail, brass, CP 600 mm long 20mm dia pipe of 1mm thick complete all as specified and directed. |
| 110 | S&F towel rail, brass, CP 600 mm long 20mm dia pipe of 1mm thick complete all as specified and directed. |
| 111 | S & F in repair brass CP Shower rose with or without swivel joints (any size) including fixing to steel pipe or union complete all as specified & directed. |
| 112 | S&F in repair glass shelf assembly consisting of 5.5mm thick sheet glass 12cm wide (as per sample) with chromium plated brackets double guard and railing 60cm long, complete all as specified and directed. |
| 113 | S&F Health foucet hand shower 8mm dia 1.20m stainless steel flexible hose with wall hook and making connection complete all as specified & directed. |
| 114 | S&F in repairs Grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms) complete all as specified and directed. |
| 115 | S&F PVC shelf of size 450mm x 100mm complete all as specified & directed. |
| 116 | S&F liquid soap sentainer of PTMT fixed with including chromium plated brass screws and wooden and plastic cleats(min wt 105 gm) complete all as specified and directed. |
| 117 | Rotational moulded polythylene 500 litres capacity water storage tank (Cylindrical vertical with closed top), 3 layer hoisted and fixed in position including 20mm brass ball valve high pressure with brass rod & high density plastic ball including dismanting of existing RCC/PVC tanks of any capacity complete all as specified and directed. |
| 118 | Rotational moulded polythylene 1000 litres capacity water storage tank (Cylindrical vertical with closed top), 3 layer hoisted and fixed in position including 20mm brass ball valve high pressure with brass rod & high density plastic ball including dismanting of water tanks of capacity exc 500 ltrs but not exc 1000 ltrs and removing to store, complete all as specified and directed. |
| 119 | S&F in repair 20 mm size gun metal globe or gate valves with iron wheel head, screwed both end for iron pipe and fixed cast copper chromium plated fancy type alloy ISI marked with crutch or butter fly handles screwed down screwed for iron pipe of 20mm bore complete all as specified and directed. |
| 120 | S&F in repair Cast iron, waste and vent pipes, sand cast, 100mm bore in any length with or without ears with cement joints, as in floor with all fittings complete all as specified and directed |
| 121 | S&F Cast iron waste and vent pipes sand cast 100mm bore in any length with or without ears with cement joints fixed to walls/in trenches with all fittings including taking down the unservicable pipe with fitting complete all as specified and directed |
| 122 | S&F in repair Cast iron, waste and vent pipes, sand cast, 75mm bore in any length with or without ears with cement joints, as in floor with all fittings complete all as specified and directed |
| 123 | S&F in repair Cast iron waste and vent pipes sand cast 75mm bore in any length with or without ears with cement joints fixed to walls/in trenches with complete all as specified and directed |
| 124 | S&F in repair 50mm bore cast iron soil, waste and vent pipes, sand cast, in any length with or without ears fixed to walls with clamps and cement joint complete all as specified and directed. |
| 125 | S&F 50mm bore cast iron soil, waste and vent pipes, sand cast, in any length with or without ears fixed to walls with clamps and cement joint complete all as specified and directed. |
| 126 | S&F in repair 100 mm bore Cast iron bends (any radius) diminishing pieces or tapers (larger bore measured) complete all as specified and directed. |
| 127 | S&F in repair 100 mm bore Cast iron bends (any radius) diminishing pieces or tapers (larger bore measured) with ovel asses door complete all as specified and directed. |
| 128 | S&F 100 mm bore Cast iron bends (any radius) diminishing pieces or tapers (larger bore measured) with ovel asses door complete all as specified and directed. |
| 129 | S&F in repair cast iron 100mm bore Branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches, fitted with ovel access doors complete all as specified and directed. |
| 130 | S&F in repairs 75mm dia Cast iron bends (any radius) diminishing pieces or tapers (larger bore measured) complete all as specified and directed. |
| 131 | S&F 75mm dia Cast iron bends (any radius) diminishing pieces or tapers (larger bore measured) with oval access door complete all as specified and directed. |
| 132 | S&F in repair cast iron 75mm bore Branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches fitted with oval access door complete all as specified and directed. |
| 133 | S&F in repair Cast iron floor trap 75mm with grating including jointing to waste pipe fixed in cement concrete 1:2:4 type B-1 with CP grating with ot without hole for waste pipe complete all as specified and directed. |
| 134 | S&F in repair Cast iron cowl of 50mm bore complete all as specified and directed. |
| 135 | S&F Cast iron cowl of 50mm bore complete all as specified and directed. |
| 136 | S&F in repair Cast iron Swan necks (or offsets) upto 152mm projection for 100mm to 50mm pipe complete all as specified and directed. |
| 137 | RCC M-25 nominal mix using 20 mm graded aggregate in column etc complete all as specified and directed. |
| 138 | RCC M-25 nominal mix using 20 mm graded aggregate as in beams, cantilevers, bressummers lintels over 1.5 m span complete all as specified and directed. |
| 139 | RCC M-25 nominal mix using 20 mm graded aggregate in chajjas etc complete all as specified and directed. |
| 140 | RCC M-25 nominal mix using 20 mm graded aggregate in foundations, including rafts, footings, foundation beams, plinth beams, base for columns, etc basements slabs under rammed piles and mass concrete complete all as specified and directed. |
| 141 | M&L for RCC M-25 nominal mix as in slabs supported on walls, beams and columns, in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified & directed. |
| 142 | RCC M-25 (Design mix) as roof beam, tie beams /lintal beam complete all as specified and directed. |
| 143 | Formwork to sides of beams and lintels with rough finished surface of concrete complete all as specified and directed. |
| 144 | Formwork to sides of columns with fair finished surface of concrete complete all as specified and directed. |
| 145 | Formwork to edges of concrete in roof slab etc similar work n.exc 20cm wide with rough finished surface of concrete complete all as specified and directed. |
| 146 | Formwork to sides of concrete foundation, footing with rough finished surface of concrete complete all as specified and directed. |
| 147 | Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings & similar works, flat, rough finished surafaces of concrete; not exceeding 200mm thick (horizontal or sloping) complete all as specified and directed |
| 148 | M& L for Form work to sides of concrete foundations, footings, bases of columns, raft beams sides and soffits (if any) of foundation and plinth beams and similar work vertical or to batter complete all as specified and directed. |
| 149 | S&F Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified & directed. |
| 150 | S&F Mild steel TMT bars 08mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed. |
| 151 | S&F Mild steel TMT bars 05mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed. |
| 152 | Precast reinforced cement concrete 1:2:4, type B-1 (using 20mm graded crushed stone aggregate) , set in CM 1:4 as in slab for for water tank/shelf. landings, cover slabs (for man holes etc) chullah hoods, chajjas, water trough, managers, shelves & similar articles with palin faces complete all as specified and directed. |
| 153 | S&F in repair 75mm bore dia PVC (SWR) pipes, single socketed, in any length with rubber ring joints, fixed to walls with clamps, complete all as specified and directed. |
| 154 | S&F 110mm bore dia PVC (SWR) pipes, single socketed, in any length with rubber ring joints, fixed to walls with clamps, complete all as specified and directed. |
| 155 | S&F in repair 110mm bore dia PVC (SWR) pipes, single socketed, in any length with rubber ring joints laid in trenches or in floor , complete all as specified and directed. |
| 156 | S&F in repair 75mm bore dia PVC (SWR) pipes, single socketed, in any length with rubber ring joints laid in trenches or in floor , complete all as specified and directed. |
| 157 | S&F in repair 110mm bore dia PVC (SWR) bends,any radius (larger bore measured), complete all as specified and directed. |
| 158 | S&F in repair 75mm bore dia PVC (SWR) bends,any radius (larger bore measured), complete all as specified and directed. |
| 159 | S&F in repair 75mm bore dia PVC (SWR) bends, fixed in repair, complete all as specified and directed. |
| 160 | S&F in repair 75mm bore pipe PVC (SWR) vent cowl, fixed in repair, complete all as specified and directed. |
| 161 | S&F in repair 110mm bore dia PVC (SWR) reducers, complete all as specified and directed. |
| 162 | S&F in repair PVC floor trap 110mm with grating including jointing to waste pipe fixed in cement concrete 1:2:4 type B-1 with CP grating with or without hole for waste pipe complete all as specified and directed. |
| 163 | S&F CI floor trap 110mm with grating including jointing to waste pipe fixed in cement concrete 1:2:4 type B-1 with CP grating with or without hole for waste pipe complete all as specified and directed. |
| 164 | M&L for PCC 1:2:4 type B-0 ( using 12.5mm graded crushed stone aggregate) padding as roof , surface finished even and smooth without using extra cement complete all as specified and directed. |
| 165 | M&L 20 mm thick cement plaster in cement mortar 1:4 on brick or concrete surface of sunken floor finished even and smooth using WPC liquid of make Dr. Fixit or STP as per manufacturer instruction @ 0.200 ltr in 50 Kg of cement complete all as specified & directed (WPC shall be measured and paid separately) |
| 166 | 10mm thick cement plaster in cement mortar 1:4 on concrete surface finished even and smooth using WPC liquid of make Dr. Fixit or STP as per manufacturer instruction @ 0.200 ltr in 50 Kg of cement including taking down all as specified and directed |
| 167 | M&L for preparation of surfaces and apply first coat fiber reinforced elastomatic liquid water proofing membrane formulated with PU hybrid ploymersand reinfoecing acrylic fibers with sun reflective index(SRI) of 100-110 having maximumelongation of 350% tensile strength od 2.9 Mpa and shall have crack bridging ability upto 2.5mm and shall resist 10 bars of hydrostatic presure and reduce surface temprerature upto 10 degree celsius with 33% ditution of priming coat. Laying of fiber mesh of 0.3mm thickness weave in leno pattern having 45 grm/sqm and pastinf it properly with overlaping of 50mm and allow it to dry, Apply second coat of undiluted coat @ 0.45 ltr/ Sqm . Apply third and final coat undiluted @ 0.45 ltr/sqm complete application to be done by the manufacture of authorised applicator complete all as specified and directed. Please Enable Macros to View BoQ information |
| 168 | M&L for preparation of surfaces and apply first coat fiber reinforced elastomatic liquid water proofing membrane formulated with PU hybrid ploymersand reinfoecing acrylic fibers with sun reflective index(SRI) of 100-110 having maximumelongation of 350% tensile strength od 2.9 Mpa and shall have crack bridging ability upto 2.5mm and shall resist 10 bars of hydrostatic presure and reduce surface temprerature upto 10 degree celsius with 33% ditution of priming coat. Laying of fiber mesh of 0.3mm thickness weave in leno pattern having 45 grm/sqm and pastinf it properly with overlaping of 50mm and allow it to dry, Apply second coat of undiluted coat @ 0.45 ltr/ Sqm . Apply third and final coat undiluted @ 0.45 ltr/sqm complete application to be done by the manufacture of authorised applicator complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 27, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 17, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 7 daysAug 25, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 15 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender